Commission Directive 89/491/EEC of 17 July 1989 adapting to technical progress Council Directives 70/157/EEC, 70/220/EEC, 72/245/EEC, 72/306/EEC, 80/1268/EEC and 80/1269/EEC relating to motor vehicles
Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗
The undermentioned Directives are hereby amended in accordance with the Annexes to this Directive: - Directive 70/157/EEC is amended in accordance with Annex I, - Directive 70/220/EEC is amended in accordance with Annex II, - Directive 72/245/EEC is amended in accordance with Annex III, - Directive 72/306/EEC is amended in accordance with Annex IV, - Directive 80/1268/EEC is amended in accordance with Annex V, - Directive 80/1269/EEC is amended in accordance with Annex VI.
Member States shall bring into force the laws, regulations and administrative provisions necessary to comply with this Directive not later than 1 January 1990. They shall forthwith inform the Commission thereof.
This Directive is addressed to the Member States. Done at Brussels, 17 July 1989. For the Commission Martin BANGEMANN Vice-President (1) OJ No L 42, 23. 2. 1970, p. 16. (2) OJ No L 192, 11. 7. 1987, p. 43. (3) OJ No L 76, 6. 4. 1970, p. 1. (4) OJ No L 214, 6. 8. 1988, p. 1. (5) OJ No L 152, 6. 7. 1972, p. 15. (6) OJ No L 190, 20. 8. 1972, p. 1. (7) OJ No L 375, 31. 12. 1980, p. 36. (8) OJ No L 375, 31. 12. 1980, p. 46. (9) OJ No L 92, 9. 4. 1988, p. 50. (10) OJ No L 36, 9. 2. 1988, p. 1.
AMENDMENTS TO ANNEX I TO DIRECTIVE 70/157/EEC 6 is added as follows: 1.2 // '6. // EXTENSION OF EEC TYPE APPROVAL // 6.1. // Vehicle types modified to run on unleaded petrol // 6.1.1. // Approval of a vehicle type modified and/or adjusted solely for the purpose of making it capable of running on unleaded petrol, as specified in Directive 85/210/EEC, shall be extended when the manufacturer certifies, subject to the approval of the authority granting type approval, that the sound level for the modified vehicle shall not exceed the limiting values specified in 5.2.2.1. // 6.2. // Vehicle types modified for any other purpose // 6.2.1. // Approval of a vehicle type may be extended to vehicle types differing with regard to the characteristics listed in Annex III if the authority granting type approval considers that the modifications made are not likely to have any substantial adverse effect on the sound level of the vehicle.' ANNEX II AMENDMENTS TO ANNEX I TO DIRECTIVE 70/220/EEC 1. The following text is inserted at the beginning of 2.2.: 1.2 // '2.2. // "Reference mass" means the mass of the vehicle in running order less the uniform mass of the driver of 75 kg and increased by a uniform mass of 100 kg.' 2. 3.2.4. is replaced by the following: 1.2 // '3.2.4. // in the case of vehicles equipped with positive ignition engines, a statement of whether either 5.1.2.1 (restricted orifice) or 5.1.2.2 (marking) applies, and in the latter case, a description of the marking.' 3. 5.1.2.1 and 5.1.2.2 are added as follows: 1.2 // '5.1.2.1. // Subject to 5.1.2.2, the inlet orifice of the fuel tank shall be so designed that it prevents the tank from being filled from a petrol pump delivery nozzle which has an external diameter of 23,6 mm or greater. // 5.1.2.2. // 5.1.2.1 does not apply to a vehicle in respect of which both of the following conditions are satisfied, that is to say - // 5.1.2.2.1. // that the vehicle is so designed and constructed that no device designed to control the emission of gaseous pollutants shall be adversely affected by leaded petrol, and // 5.1.2.2.2. // that it is conspicuously, legibly and indelibly marked with the symbol for unleaded petrol (4.26) specified in ISO 2757-1985 (1) in a position immediately visible to a person filling the fuel tank. Additional marking shall be permitted.' (1) Reproduced as figure 22 of Annex II to Directive 78/316/EEC. ANNEX III AMENDMENTS TO ANNEX I TO DIRECTIVE 72/245/EEC 8 is added as follows: 1.2 // '8. // EXTENSION OF EEC TYPE APPROVAL // 8.1. // Vehicle types modified to run on unleaded petrol // 8.1.1. // Approval of a vehicle type modified and/or adjusted solely for the purpose of making it capable of running on unleaded petrol, as specified in Directive 85/210/EEC, shall be extended when the manufacturer certifies, subject to the radio interference suppression for the modified vehicles remain within the limits for conformity of production, as specified in 9 to this Annex. // 8.2. // Vehicles types modified for any other purpose // 8.2.1. // Approval of a vehicle type may be extended to vehicle types differing with regard to the characteristics listed in 2.2 to this Annex if the authority granting type approval considers that the modification made are not likely to have any substantial adverse effect on the radio interference suppression of the vehicle.' ANNEX IV AMENDMENTS TO ANNEX V TO DIRECTIVE 72/306/EEC Annex V is replaced by the following: 'TECHNICAL CHARACTERISTICS OF REFERENCE FUEL PRESCRIBED FOR APPROVAL TESTS AND TO VERIFY CONFORMITY OF PRODUCTION CEC reference fuel RF-03-A-84 (1) (3) (7) 1.2.3 // // // // // Limits and units // ASTM method // // // // Cetan number (4) // min 49 max 53 // D 613 // Density 15 °C (Kg/1) // min 0,835 max 0,845 // D 1298 // Destillation (2) 50 % 90 % FBP // min 245 °C min 320 °C max 340 °C max 370 °C // D 86 // Flash point // min 55 °C // D 93 // CFPP // min - max - 5 °C // EN 116 (CEN) // Viscosity 40 °C // min 2,5 mm2/S max 3,5 mm2/S // D 445 // Sulphur content // min (to be reported) // D 1266/D 2622 D 2785 // // max 0,3 % mass // // Copper corrosion // max 1 // D 130 // Conradson carbon residue (10 % DR) // max 0,2 % mass // D 189 // Ash content // max 0,01 % mass // D 482 // Water content // max 0,05 % mass // D 95/D 1744 // Neutralization (strong acid) number // max 0,2 mg KPH/g // // Oxidation stability (6) // max 2,5 mg/100 m // D 2274 // Additives (5) // // // Carbon-hydrogen ratio // (to be reported) // // // // (1) Equivalent ISO methods will be adopted when issued all properties listed above. (2) The figures quoted show the evaporated quantities (percentage recovered + percentage loss). (3) The values quoted in the specification are 'true values'. In estabishment of their limit values the terms of ASTM D 3244 'Defining a basis for petroleum product quality disputes' have been applied and in fixing a maximum value, a minimum difference of 2R above zero has been taken into account; in fixing a maximum and minimum value, the minimum difference is 4R (R = reproducibility). Notwithstanding this measure, which is necessary for statistical reasons, the manufacturer of fuel should nevertheless aim at a zero value where the stipulated maximum value is 2R and at the mean value in the case of quotations of maximum and minimum limits. Should it be necessary to clarify the question as to whether a fuel meets the requirements of the specification, the terms of ASTM D 3244 be applied. (4) The range for cetane is note in accordance with the requirement of a minimum range of 4R. However, in cases of dispute between fuel supplier and fuel user, the terms of ASTM D 3244 can be used to resolve such disputes provided replicate measurements, of sufficient number to achieve the necessary precision, are made in preference to single determinations. (5) This fuel should be based on straight run and cracked hydrocarbon distillate components only; desulphurization is allowed. It must not contain any metallic additives or cetane improver additives. (6) Even though oxidation stability is controlled, it is likely that shell life will be limited. Advice should be sought from the supplier as to storage conditions and life. (7) If it is required to calculate thermal efficiency of an engine or vehicle, the calorific value of the fuel can be calculated from: Specific energy (calorific value) (net) MJ/kg = (46,423 - 8,792d2 + 3,170d) (1 - (x+y+s)) + 9,420s - 2,499x 1.2.3 // where: // d // = the density at 15 °C, // // x // = the proportion by mass of water (%/100), // // y // = the proportion by mass of ash (%/100), // // s // = the proportion by mass of sulphur (%/100).' ANNEX V AMENDMENTS TO ANNEX I TO DIRECTIVE 80/1268/EEC 1. 3.1.1 is amended as follows: Delete 'as last amended by Directive 78/665/EEC' 2. 7 is added as follows: 1.2 // '7. // EXTENSION OF EEC TYPE APPROVAL // 7.1. // Vehicle types modified to run on unleaded petrol // 7.1.1. // Subject to the approval of the authority granting type approval, approval of a vehicle type modified and/or adjusted solely for the purpose of making it capable of running on unleaded petrol, as specified in Directive 85/210/EEC, shall be extended under the following alternative conditions: // 7.1.1.1. // The manufacturer shall certify that the fuel consumption for each test condition does not exceed by more than 5 % the figure obtained with the original, unmodified, type approved vehicle. In this case the extension shall confirm the figures the original type approval, or. // 7.1.1.2. // The manufacturer shall declare a revised fuel consumption figure for any of the three test conditions which exceeds by more than 5 % the figure obtained with the original, unmodified, type approved vehicle. In this case the extension shall specify the newly declared figures as applicable to the modified vehicle type. // 7.2. // Vehicle types modified for any other purpose // 7.2.1. // Approval of a vehicle type may be extended to vehicle types differing with regard to the characteristics listed in Annex II if the authority granting type approval considers that the modifications made are not likely to have any substantial adverse effect on the fuel consumption of the vehicle.' ANNEX VI AMENDMENTS TO ANNEX I TO DIRECTIVE 88/1269/EEC 1. 8 is replaced by: 1.2 // '8. // EXTENSION OF EEC TYPE APPROVAL // 8.1. // Vehicle types modified to run on unleaded petrol // 8.1.1. // Subject to the approval of the authority granting type approval, approval of a vehicle type modified and/or adjusted solely for the purpose of making it capable of running on unleaded petrol, as specified in Directive 85/210/EEC, shall be extended under the following alternative conditions: // 8.1.1.1. // The manufacturer shall certify that the engine power of the modified vehicle shall remain within the limits for conformity of production, as specified in 9.2 as obtained with the original, unmodified, type approved vehicle. In this case the extension shall confirm the power of the original type approval, or // 8.1.1.2. // The manufacturer shall declare a revised engine power figure which is less than that obtained with the original, unmodified type approved vehicle. In this case the extension shall specify the newly declared figures as applicable to the modified vehicle type. // 8.2. // Vehicle types modified for any other purpose // // Any other modification of the engine with regard to the characteristics listed in Appendix 1 or Apendix 2 to this Annex shall be reported to the competent authority. That authority may then either: // 8.2.1. // consider that the modifications made are not likely to have any substantial effect on the power of the engine, or // 8.2.2. // request a further determination of engine power through the carrying-out of such tests as are deemed necessary.' 2. 9 is replaced by: 1.2 // '9. // TOLERANCES FOR MEASURING THE NET POWER // 9.1. // The net power indicated by the manufacturer for the type of engine shall be accepted if it does not differ by more than ± 2 % for maximum power and more than ± 4 % at, the other measurement points on the curve with a tolerance of ± 1,5 % for engine speed, from the values measured by the technical service on the engine submitted for testing. // 9.2 // During the tests to verify conformity of production the power shall be measured at two engine speeds S1 and S2 corresponding respectively to the measurement points of maximum power and maximum torque accepted for type approval. At these two engine speeds, which are subject to a tolerance of + 5 %, the net power measured at at least one point within the ranges S1 ± 5 % and S2 ± 5 % shall not differ by more than ± 5 % from the approval figure'.
Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.