97/176/EC: Commission Decision of 17 February 1997 on the procedure for attesting the conformity of construction products pursuant to Article 20 (2) of Council Directive 89/106/EEC as regards structural timber products and ancillaries (Text with EEA relevance)
Data as of 2026-07-04 Β· Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. Β· Read the official text β
The products and families of products set out in Annex I shall have their conformity attested by a procedure whereby the manufacturer has under its sole responsibility a factory production control system ensuring that the product in is conformity with the relevant technical specifications.
The products set out in Annex II shall have their conformity attested by a procedure whereby, in addition to a factory production control system operated by the manufacturer, an approved certification body is involved in assessment and surveillance of the production control or of the product itself.
The procedure for attesting conformity as set out in Annex III shall be indicated in mandates for harmonized standards.
This Decision is addressed to the Member States. Done at Brussels, 17 February 1997. For the Commission Martin BANGEMANN Member of the Commission (1) OJ No L 40, 11. 2. 1989, p. 12. (2) OJ No L 220, 30. 8. 1993, p. 1.
Fasteners for structural timber products Connectors for timber, split ring connectors, cylindrical steel and wood dowels, wood screws, threaded bolts, wood nails. These products can be treated against fire, biological attack, or not treated. ANNEX II Solid structural timber products Elements Bridge elements, truss elements, sleepers, floor elements, wall elements, roof elements such as beams, arches, joist, rafters, columns, poles, piles. Kits Trusses, floors, walls, roofs, frames. These products can be treated against fire, biological attack, or not treated. Timber poles Structural glued laminated products and other glued timber products Elements Bridge elements, truss elements, floor elements, wall elements, roof elements such as beams, arches, joist, rafters, columns, poles, piles. Kits Trusses, floors, walls, roofs, frames. These products can be treated against fire, biological attack, or not treated. ANNEX III PRODUCT FAMILY STRUCTURAL TIMBER PRODUCTS (1/3) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec (European Committee for Standardization/European Committee for Electrotechnical Standardization) are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s): >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristics, see Article 2 (1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the interpretative documents. In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY STRUCTURAL TIMBER PRODUCTS (2/3) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec (European Committee for Standardization/European Committee for Electrotechnical Standardization) are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s): >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic, see Article 2 (1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the interpretative documents. In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY STRUCTURAL TIMBER PRODUCTS (3/3) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec (European Committee for Standardization/European Committee for Electrotechnical Standardization) are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s): >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic, see Article 2 (1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the interpretative documents. In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
Source: EUR-Lex (Publications Office of the EU), Β© European Union, reuse permitted under Commission Decision 2011/833/EU.