97/597/EC: Commission Decision of 14 July 1997 on the procedure for attesting the conformity of construction products pursuant to Article 20 (2) of Council Directive 89/106/EEC as regards reinforcing and prestressing steel for concrete (Text with EEA relevance)
Data as of 2026-07-04 Β· Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. Β· Read the official text β
The products and families of products set out in Annex I shall have their conformity attested by a procedure whereby the manufacturer has under its sole responsibility a factory production control system ensuring that the product is in conformity with the relevant technical specifications.
The products set out in Annex II shall have their conformity attested by a procedure whereby, in addition to a factory production control system operated by the manufacturer, an approved certification body is involved in assessment and surveillance of the production control or of the product itself.
The procedure for attesting conformity as set out in Annex III shall be indicated in mandates for harmonized standards.
This Decision is addressed to the Member States. Done at Brussels, 14 July 1997. For the Commission Martin BANGEMANN Member of the Commission (1) OJ L 40, 11. 2. 1989, p. 12. (2) OJ L 220, 30. 8. 1993, p. 1.
Ducts and sheaths for protection or guide of prestressing steel products ANNEX II Reinforcing steel products for concrete Bars Rods, coils Welded fabrics Lattice girder Indented strips Prestressing steel products for concrete Wires (stress relieved cold drawn wires, smooth wires, indented wires) Strands (multi-wire strands, multi-wire compacted strands, indented and high bond strand) Bars (hot rolled and processed bars, threaded bars, ribbed or plane or smooth bars) Prestressing cables ANNEX III PRODUCT FAMILY REINFORCING AND PRESTRESSING STEEL FOR CONCRETE (1/3) 1. Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/CENELEC are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s): >TABLE> 2. Conditions to be applied by CEN on the specifications of the attestation of conformity system The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of the CPD and, where applicable, clause 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY REINFORCING AND PRESTRESSING STEEL FOR CONCRETE (2/3) 1. Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/CENELEC are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s): >TABLE> 2. Conditions to be applied by CEN on the specifications of the attestation of conformity system The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of the CPD and, where applicable, clause 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY REINFORCING AND PRESTRESSING STEEL FOR CONCRETE (3/3) 1. Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/CENELEC are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s): >TABLE> 2. Conditions to be applied by CEN on the specifications of the attestation of conformity system The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of the CPD and, where applicable, clause 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
Source: EUR-Lex (Publications Office of the EU), Β© European Union, reuse permitted under Commission Decision 2011/833/EU.