1999/472/EC: Commission Decision of 1 July 1999 on the procedure for attesting the conformity of construction products pursuant to Article 20(2) of Council Directive 89/106/EEC as regards pipes, tanks and ancillaries not in contact with water intended for human consumption (notified under document number C(1999) 1482) (Text with EEA relevance)
Data as of 2026-07-04 Β· Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. Β· Read the official text β
The products and families of products set out in Annex I shall have their conformity attested by a procedure whereby the manufacturer has under its sole responsability a factory production control system ensuring that the product is in conformity with the relevant technical specifications.
The products set out in Annex II shall have their conformity attested by a procedure whereby, in addition to a factory production control system operated by the manufacturer, an approved certification body is involved in assessment and surveillance of the production control or of the product itself.
The procedure for attesting conformity as set out in Annex III shall be indicated in mandates for harmonised standards.
This Decision is addressed to the Member States. Done at Brussels, 1 July 1999. For the Commission Karel VAN MIERT Member of the Commission (1) OJ L 40, 11.2.1989, p. 12. (2) OJ L 220, 30.8.1993, p. 1.
Piping kits, pipes, tanks, leakage alarm systems, overfill prevention devices, fittings, adhesives, joints, joint sealings, gaskets, ducts and conduits for protection, pipe/duct supports, valves and taps, safety ancillaries For use in installations for the transport/distribution/storage of gas/fuel intended for the supply of building heating/cooling systems, from the external storage reservoir or the last pressure reduction unit of the network to the inlet of the heating/cooling systems of the building, and in installations for the transport/disposal/storage of water not intended for human consumption, and for heating systems, other than those specified in Annex II. ANNEX II Tanks, ducts and conduits for protection For use in areas subject to resistance to fire regulations, in installations for the transport/distribution/storage of gas/fuel intended for the supply of building heating/cooling systems, from the external storage reservoir or the last pressure reduction unit of the network to the inlet of the heating/cooling systems of the building. Piping kits, pipes, tanks, leakage alarm systems, overfill prevention devices, fittings, adhesives, joints, joint sealings, gaskets, ducts and conduits for protection, pipe/duct supports, valves and taps, safety ancillaries For use in areas subject to reaction to fire regulations, in installations for the transport/distribution/storage of gas/fuel intended for the supply of building heating/cooling systems, from the external storage reservoir or the last pressure reduction unit of the network to the inlet of the heating/cooling systems of the building, and in installations for the transport/disposal/storage of water not intended for human consumption for products for which the reaction to fire class is A(1), B(2) or C(3). (1) Materials for which the reaction to fire performance is susceptible to change during production (In general, those subject to chemical modification, e.g. fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (2) Materials for which the reaction to fire performance is susceptible to change during production (In general, those subject to chemical modification, e.g. fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (3) Materials for which the reaction to fire performance is susceptible to change during production (In general, those subject to chemical modification, e.g. fire retardants, or where changes of composition may lead to changes in reaction to fire performance). ANNEX II Note: for products having more than one of the intended uses specified in the following families, the tasks for the approved body, derived from the relevant systems of attestation of conformity, are cumulative. PRODUCT FAMILY PIPES, TANKS AND ANCILLARIES NOT IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION (1/5) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> System 3: See Directive 89/106/EEC, Annex III(2)(ii), second possibility. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY PIPES, TANKS AND ANCILLARIES NOT IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION (2/5) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> System 4: See Directive 89/106/EEC, Annex III.2(ii), third possibility. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2(1) of Directive 89/160/EEC and where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY PIPES, TANKS AND ANCILLARIES NOT IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION (3/5) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> System 1: See Directive 89/106/EEC, Annex III(2)(I), without audit-testing of samples. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2(1) of Directive 89/160/EEC and where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY PIPES, TANKS AND ANCILLARIES NOT IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION (4/5) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> System 1: See Directive 89/106/EEC, Annex II(2)(I), without audit-testing of samples. System 3: See Directive 89/106/EEC, Annex III(2)(ii), second possibility. System 4: See Directive 89/106/EEC, Annex III(2)(ii), third possibility. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2(1) of Directive 89/160/EEC and where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY PIPES, TANKS AND ANCILLARIES NOT IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION (5/5) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> System 3: See Directive 89/106/EEC, Annex III(2)(ii), second possibility. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2(1) of Directive 89/160/EEC and where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
Source: EUR-Lex (Publications Office of the EU), Β© European Union, reuse permitted under Commission Decision 2011/833/EU.