2000/273/EC: Commission Decision of 27 March 2000 on the procedure for attesting the conformity of construction products pursuant to Article 20(2) of Council Directive 89/106/EEC as regards seven products for European Technical Approvals without Guideline (notified under document number C(2000) 668) (Text with EEA relevance)
Data as of 2026-07-04 Β· Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. Β· Read the official text β
The products set out in Annex I shall have their conformity attested by a procedure whereby the manufacturer has under its sole responsibility a factory production control system ensuring that the product is in conformity with the relevant technical specifications.
The products set out in Annex II shall have their conformity attested by a procedure whereby, in addition to a factory production control system operated by the manufacturer, an approved certification body is involved in assessment and surveillance of the production control or of the product itself.
The procedure for attesting conformity as set out in Annex III shall be indicated in the relevant European technical approvals.
This Decision is addressed to the Member States. Done at Brussels, 27 March 2000. For the Commission Erkki Liikanen Member of the Commission (1) OJ L 40, 11.2.1989, p. 12. (2) OJ L 220, 30.8.1993, p. 1.
Vibration and impact noise isolation kit for floating floors (EOTA ref. 05.03/03): For uses except those subject to reaction to fire regulations for products made of materials falling into classes AFL(1), BFL(2), CFL(3), Vibration and noise isolation kit for walls (EOTA ref. 06.01/09): For uses except those subject to reaction to fire regulations for products made of materials falling into classes A(4), B(5), C(6), Wall plates made of stainless steel (EOTA ref. 06.04/04) Waste water trap kit (EOTA ref. 07.04/04) (1) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (2) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (3) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (4) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (5) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (6) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). ANNEX II Vibration and impact noise isolation kit for floating floors (EOTA ref. 05.03/03): For uses subject to reaction to fire regulations for products made of materials falling into classes AFL(1), BFL(2), CFL(3) Vibration and noise isolation kit for walls (EOTA ref. 06.01/09): For uses subject to reaction to fire regulations for products made of materials falling into classes A(4), B(5), C(6) Channel bars (EOTA ref. 06.01/01) Chemical anchoring kit (EOTA ref. 06.01/11) Epoxy concrete/glass-reinforced polyester/epoxy mortar anchoring kit (EOTA ref. 06.03/03) (1) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (2) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (3) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (4) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (5) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). (6) Materials for which the reaction to fire performance is susceptible to change during production. (In general, those subject to chemical modification, for example fire retardants, or where changes of composition may lead to changes in reaction to fire performance). ANNEX III ATTESTATION OF CONFORMITY Note: For products/kits having more than one of the intended uses specified in the following families, the tasks for the approved body, derived from the relevant systems of attestation of conformity, are cumulative. PRODUCT FAMILY SEVEN PRODUCTS FOR EUROPEAN TECHNICAL APPROVALS (1/2) Systems of attestation of conformity For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant European technical approval: >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY SEVEN PRODUCTS FOR EUROPEAN TECHNICAL APPROVALS (2/2) Systems of attestation of conformity For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant European technical approval: >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
Source: EUR-Lex (Publications Office of the EU), Β© European Union, reuse permitted under Commission Decision 2011/833/EU.