2003/656/EC: Commission Decision of 12 September 2003 on the procedure for attesting the conformity of construction products pursuant to Article 20(2) of Council Directive 89/106/EEC as regards seven products for European technical approvals without Guideline (Text with EEA relevance) (notified under document number C(2003) 3247)
Data as of 2026-07-04 Β· Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. Β· Read the official text β
The products and families of products set out in Annex I shall have their conformity attested by a procedure whereby the manufacturer has under its sole responsibility a factory-production control system ensuring that the product is in conformity with the relevant technical specifications.
The products and families of products set out in Annex II shall have their conformity attested by a procedure whereby, in addition to a factory-production control system operated by the manufacturer, an approved certification body is involved in assessment and surveillance of the production control or of the product itself.
The procedure for attesting conformity as set out in Annex III shall be indicated in the European technical approvals.
This Decision is addressed to the Member States. Done at Brussels, 12 September 2003. For the Commission Erkki Liikanen Member of the Commission (1) OJ L 40, 11.2.1989, p. 12. (2) OJ L 220, 30.8.1993, p. 1.
- Surface water repellent product - hydrophobic agents based on organometallic substances (EOTA ref. 06.05/02): to be used for the treatment of porous building materials, mostly in facades. - Sealing kits, profiles and strips (EOTA ref. 06.05/01 and 06.05/04): to be used as sealing joints in construction works, including the building envelope for reasons of weather tightness. ANNEX II - Single point supported vertical glazing (EOTA ref. 04.04/25): to be used for ventilated curtain wall facades or for space-enclosing vertical glazing. - Point fastener (EOTA ref. 06.02/03): to be used for pinned fastenings of suspended claddings. - Coating system eliminating electrostatic charges for facilities used for storage filling and handling of water endangering liquids (EOTA ref. 06.05/13): to be used for the sealing of collecting basins, rooms as well as for reinforced concrete surfaces in the case of handling of certain water endangering liquids. - Coating system for facilities for the storage, filling and handling of water endangering liquids (EOTA ref. 06.05/14): to be used for the sealing of collecting basins, rooms as well as for reinforced concrete surfaces in the case of handling of certain water endangering liquids. - Joints sealing compounds and profiles (EOTA ref. 06.05/11 and 06.05/12): to be used for the sealing of construction works or parts of them used for containment, filling and handling of water endangering substances. ANNEX III Note: for products having more than one of the intended uses specified in the following families, the tasks for the approved body, derived from the relevant systems of attestation of conformity, are cumulative. Product family: products for ETAs without Guideline (1/2) Systems of attestation of conformity For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant European technical approvals: >TABLE> System 1: see Directive 89/106/EEC Annex III(2)(i), without audit-testing of samples. System 2+: see Directive 89/106/EEC Annex III(2)(ii), first possibility including certification of factory production control by an approved body on the basis of initial inspection of factory and of factory production control as well as of continuous surveillance, assessment and approval of the factory production control. System 4: see Directive 89/106/EEC Annex III(2)(ii), third possibility. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. Product family: products for ETAs without Guideline (2/2) Systems of attestation of conformity For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant European technical approvals: >TABLE> System 1: see Directive 89/106/EEC Annex III(2)(i), without audit-testing of samples. System 3: see Directive 89/106/EEC Annex III(2)(ii), second possibility. System 4: see Directive 89/106/EEC Annex III(2)(ii), third possibility. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
Source: EUR-Lex (Publications Office of the EU), Β© European Union, reuse permitted under Commission Decision 2011/833/EU.