2006/704/EC: Commission Decision of 20 October 2006 on the publication with restriction of the reference of standard EN 848-3:1999 Safety of woodworking machines — One side moulding machines with rotating tool — Part 3: Numerical control (NC) boring machines and routing machines in accordance with Directive 98/37/EC of the European Parliament and of the Council (notified under document number C(2006) 4901) (Text with EEA relevance)

• CELEX: Directive 98/37/EC
• Articles: 4

Article 1

The publication in the Official Journal of the European Union of the reference of standard EN 848-3:1999 ‘Safety of woodworking machines — One side moulding machines with rotating tool — Part 3: Numerical control (NC) boring machines and routing machines’ is replaced by the text set out in the Annex.

Article 2

Where, pursuant to Article 5(2) of Directive 98/37/EC, Member States publish the reference of a national standard transposing harmonised standard EN 848-3:1999, they shall add to that publication a warning identical to that set out in the Annex to this Decision.

Article 3

This Decision is addressed to the Member States.

Schedules & Appendices

ANNEX

ANNEX

‘(Publication of titles and references of harmonised standards under the directive)

ESO  ( 1 )

Reference and title of the harmonised standard

(and reference document)

First publication OJ

Reference of superseded standard

Date of cessation of presumption of conformity of superseded standard

Note 1

CEN

EN 848-3:1999

Safety of woodworking machines — One side moulding machines with rotating tool — Part 3: Numerical control (NC) boring machines and routing machines

15.4.2000

—

Warning: With regard to the characteristics of and the choice of materials for curtain guards, especially strip curtains, this publication does not concern clauses 5.2.7.1.2 (b), paragraphs 1 to 6, of this standard, the application of which does not confer a presumption of conformity to the essential health and safety requirements 1.3.2, 1.3.3 and 1.4.1 of Annex I to Directive 98/37/EC in conjunction with essential health and safety requirement 1.1.2 (a) of that Annex.

Note 1

Generally the date of cessation of presumption of conformity will be the date of withdrawal (“dow”), set by the European Standardisation Organisation, but attention of users of these standards is drawn to the fact that in certain exceptional cases this can be otherwise.

Note 2.1

The new (or amended) standard has the same scope as the superseded standard. On the date stated, the superseded standard ceases to give presumption of conformity with the essential requirements of the directive.

Note 3

In case of amendments, the referenced standard is EN CCCCC:YYYY, its previous amendments, if any, and the new, quoted amendment. The superseded standard (column 3) therefore consists of EN CCCCC:YYYY and its previous amendments, if any, but without the new quoted amendment. On the date stated, the superseded standard ceases to give presumption of conformity with the essential requirements of the directive.

Note 4

Presumption of conformity for a product is achieved by complying with the requirements of Part 1 and the relevant Part 2 when this Part 2 is also listed in the OJ under Directive 98/37/EC.

Note:

—

Any information concerning the availability of the standards can be obtained either from the European Standardisation Organisations or from the national standardisation bodies of which the list is annexed to the Directive 98/34/EC  ( 2 ) of the European Parliament and Council amended by the Directive 98/48/EC  ( 3 ) .

—

Publication of the references in the Official Journal of the European Union does not imply that the standards are available in all the Community languages.

—

This list replaces all the previous lists published in the Official Journal of the European Union . The Commission ensures the updating of this list.

More information about harmonised standards on the Internet at http://europa.eu.int/comm/enterprise/newapproach/standardization/harmstds/

( 1 )   ESO: European Standardisation Organisation:

—

CEN: rue de Stassart 36, B-1050 Brussels, Tel. [phone]; fax [phone] (http://www.cenorm.be),

—

CENELEC: rue de Stassart 35, B-1050 Brussels, Tel. [phone]; fax [phone] (http://www.cenelec.org),

—

ETSI: 650, route des Lucioles, F-06921 Sophia Antipolis, Tel. [phone]; fax [phone] (http://www.etsi.org).

( 2 )

OJ L 204, 21.7.1998, p. 37 .

( 3 )

OJ L 217, 5.8.1998, p. 18 .’