Article 1
The Annex to Decision 2006/771/EC is replaced by the Annex to this Decision.
2010/368/: Commission Decision of 30 June 2010 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices (notified under document C(2010) 4313) (Text with EEA relevance )
2010/368/: Commission Decision of 30 June 2010 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices (notified under document C(2010) 4313) (Text with EEA relevance )
Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗
Article 2
This Decision is addressed to the Member States.
Supplementary provisions
ANNEXSupplementary provisions
ANNEX ‘ANNEX Harmonised frequency bands and technical parameters for short-range devices Type of short-range device Frequency band ( 1 ) Transmit power limit/field strength limit/power density limit ( 2 ) Additional parameters (channelling and/or channel access and occupation rules) ( 3 ) Other usage restrictions ( 4 ) Implementation deadline Non-specific short-range devices ( 5 ) 6 765 -6 795 kHz 42 dBμA/m at 10 metres 1 October 2008 13,553-13,567 MHz 42 dBμA/m at 10 metres 1 October 2008 26,957-27,283 MHz 10 mW effective radiated power (e.r.p.), which corresponds to 42 dBμA/m at 10 metres Video applications are excluded 1 June 2007 40,660-40,700 MHz 10 mW e.r.p. Video applications are excluded 1 June 2007 Non-specific short-range devices (cont.) 433,050-434,040 ( 6 ) MHz 1 mW e.r.p. and – 13 dBm/10 kHz power density for bandwidth modulation larger than 250 kHz Voice applications allowed with advanced mitigation techniques Audio and video applications are excluded 1 November 2010 10 mW e.r.p. Duty cycle limit ( 7 ) : 10 % Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 434,040-434,790 ( 6 ) MHz 1 mW e.r.p. and – 13 dBm/10 kHz power density for bandwidth modulation larger than 250 kHz Voice applications allowed with advanced mitigation techniques Audio and video applications are excluded 1 November 2010 10 mW e.r.p. Duty cycle limit ( 7 ) : 10 % Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 Duty cycle limit ( 7 ) : 100 % subject to channel spacing up to 25 kHz Voice applications allowed with advanced mitigation techniques Audio and video applications are excluded 1 November 2010 Non-specific short-range devices (cont.) 863,000-865,000 MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 865,000-868,000 MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 1 % may also be used Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 868,000-868,600 MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 1 % may also be used Analogue video applications are excluded 1 November 2010 868,700-869,200 MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used Analogue video applications are excluded 1 November 2010 Non-specific short-range devices (cont.) 869,400-869,650 ( 6 ) MHz 500 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 10 % may also be used Channel spacing must be 25 kHz, except that the whole band may also be used as a single channel for high-speed data transmission Analogue video applications are excluded 1 November 2010 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 869,700-870,000 ( 6 ) MHz 5 mW e.r.p. Voice applications allowed with advanced mitigation techniques Audio and video applications are excluded 1 June 2007 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 1 % may also be used Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 Non-specific short-range devices (cont.) 2 400 -2 483,5 MHz 10 mW equivalent isotropic radiated power (e.i.r.p.) 1 June 2007 5 725 -5 875 MHz 25 mW e.i.r.p. 1 June 2007 24,150-24,250 GHz 100 mW e.i.r.p. 1 October 2008 61,0-61,5 GHz 100 mW e.i.r.p. 1 October 2008 Wideband data transmission systems 2 400 -2 483,5 MHz 100 mW e.i.r.p. and 100 mW/100 kHz e.i.r.p. density applies when frequency hopping modulation is used, 10 mW/MHz e.i.r.p. density applies when other types of modulation are used Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used 1 November 2009 57,0-66,0 GHz 40 dBm e.i.r.p. and 13 dBm/MHz e.i.r.p. density Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used Fixed outdoor installations are excluded 1 November 2010 Alarm systems 868,600-868,700 MHz 10 mW e.r.p. Channel spacing: 25 kHz The whole frequency band may also be used as a single channel for high-speed data transmission Duty cycle limit ( 7 ) : 1,0 % 1 October 2008 869,250-869,300 MHz 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit ( 7 ) : 0,1 % 1 June 2007 869,300-869,400 MHz 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit ( 7 ) : 1,0 % 1 October 2008 869,650-869,700 MHz 25 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit ( 7 ) : 10 % 1 June 2007 Social alarms ( 8 ) 869,200-869,250 MHz 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit ( 7 ) : 0,1 % 1 June 2007 Inductive applications ( 9 ) 9,000-59,750 kHz 72 dBμA/m at 10 metres 1 November 2010 59,750-60,250 kHz 42 dBμA/m at 10 metres 1 June 2007 60,250-70,000 kHz 69 dBμA/m at 10 metres 1 June 2007 70-119 kHz 42 dBμA/m at 10 metres 1 June 2007 119-127 kHz 66 dBμA/m at 10 metres 1 June 2007 127-140 kHz 42 dBμA/m at 10 metres 1 October 2008 140-148,5 kHz 37,7 dBμA/m at 10 metres 1 October 2008 148,5-5 000 kHz In the specific bands mentioned below, higher field strengths and additional usage restrictions apply: – 15 dBμA/m at 10 metres in any bandwidth of 10 kHz Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz 1 October 2008 Inductive applications (cont.) 400-600 kHz – 8 dBμA/m at 10 metres This set of usage conditions applies to RFID ( 10 ) only 1 October 2008 3 155 -3 400 kHz 13,5 dBμA/m at 10 metres 1 October 2008 5 000 -30 000 kHz In the specific bands mentioned below, higher field strengths and additional usage restrictions apply: – 20 dBμA/m at 10 metres in any bandwidth of 10 kHz Furthermore the total field strength is -5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz 1 October 2008 6 765 -6 795 kHz 42 dBμA/m at 10 metres 1 June 2007 7 400 -8 800 kHz 9 dBμA/m at 10 metres 1 October 2008 10 200 -11 000 kHz 9 dBμA/m at 10 metres 1 October 2008 Inductive applications (cont.) 13 553 -13 567 kHz 42 dBμA/m at 10 metres 1 June 2007 60 dBμA/m at 10 metres This set of usage conditions applies to RFID ( 10 ) and EAS ( 11 ) only 1 October 2008 26 957 -27 283 kHz 42 dBμA/m at 10 metres 1 October 2008 Active medical implants ( 12 ) 9-315 kHz 30 dBμA/m at 10 metres Duty cycle limit ( 7 ) : 10 % 1 October 2008 30,0-37,5 MHz 1 mW e.r.p. Duty cycle limit ( 7 ) : 10 % This set of usage conditions applies to ultra low power medical membrane implants for blood pressure measurements only 1 November 2010 402-405 MHz 25 μW e.r.p. Channel spacing: 25 kHz Individual transmitters may combine adjacent channels for increased bandwidth up to 300 kHz. Other techniques to access spectrum or mitigate interference, including bandwidths greater than 300 kHz, can be used provided they result at least in an equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC to ensure compatible operation with the other users and in particular with meteorological radiosondes 1 November 2009 Active medical implants and associated peripherals ( 13 ) 401-402 MHz 25 μW e.r.p. Channel spacing: 25 kHz Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used 1 November 2010 405-406 MHz 25 μW e.r.p. Channel spacing: 25 kHz Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used 1 November 2010 Animal implantable devices ( 14 ) 315-600 kHz – 5 dΒμΑ/m at 10 m Duty cycle limit ( 7 ) : 10 % 1 November 2010 12,5-20,0 MHz – 7 dΒμΑ/m at 10 m in a bandwidth of 10 kHz Duty cycle limit ( 7 ) : 10 % This set of usage conditions applies to indoor applications only 1 November 2010 Low power FM transmitters ( 15 ) 87,5-108,0 MHz 50 nW e.r.p. Channel spacing up to 200 kHz 1 November 2010 Wireless audio applications ( 16 ) 863-865 MHz 10 mW e.r.p. 1 November 2010 Radio determination applications ( 17 ) 2 400 -2 483,5 MHz 25 mW e.i.r.p. 1 November 2009 17,1-17,3 GHz 26 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used This set of usage conditions applies to ground-based systems only 1 November 2009 Tank Level Probing Radar ( 18 ) 4,5-7,0 GHz 24 dBm e.i.r.p. ( 19 ) 1 November 2009 8,5-10,6 GHz 30 dBm e.i.r.p. ( 19 ) 1 November 2009 24,05-27,0 GHz 43 dBm e.i.r.p. ( 19 ) 1 November 2009 57,0-64,0 GHz 43 dBm e.i.r.p. ( 19 ) 1 November 2009 75,0-85,0 GHz 43 dBm e.i.r.p. ( 19 ) 1 November 2009 Model Control ( 20 ) 26 990 -27 000 kHz 100 mW e.r.p. 1 November 2009 27 040 -27 050 kHz 100 mW e.r.p. 1 November 2009 27 090 -27 100 kHz 100 mW e.r.p. 1 November 2009 27 140 -27 150 kHz 100 mW e.r.p. 1 November 2009 27 190 -27 200 kHz 100 mW e.r.p. 1 November 2009 Radio Frequency Identification (RFID) 2 446 -2 454 MHz 100 mW e.i.r.p. 1 November 2009 Road Transport and Traffic Telematics 76,0-77,0 GHz 55 dBm peak e.i.r.p. and 50 dBm mean e.i.r.p. and 23,5 dBm mean e.i.r.p. for pulse radars This set of usage conditions applies to terrestrial vehicle and infrastructure systems only 1 November 2010 ( 1 ) Member States must allow the usage of adjacent frequency bands within this table as a single frequency band provided the specific conditions of each of these adjacent frequency bands are met. ( 2 ) Member States must allow the usage of spectrum up to the transmit power, field strength or power density given in this table. In conformity with Article 3(3) of Decision 2006/771/EC, they may impose less restrictive conditions, i.e. allow the use of spectrum with higher transmit power, field strength or power density. ( 3 ) Member States may only impose these “additional parameters (channelling and/or channel access and occupation rules)”, and may not add other parameters or spectrum access and mitigation requirements. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may completely omit the ‘additional parameters (channelling and/or channel access and occupation rules)’ in a given cell or allow higher values. ( 4 ) Member States may only impose these “other usage restrictions”, and may not add additional usage restrictions. As less restrictive conditions may be introduced within the meaning of Article 3(3) of Decision 2006/771/EC, Member States may omit one or all of these restrictions. ( 5 ) This category is available for any type of application which fulfils the technical conditions (typical uses are telemetry, telecommand, alarms, data in general and other similar applications). ( 6 ) For this frequency band Member States must make all the alternative sets of usage conditions possible. ( 7 ) “Duty cycle” means the ratio of time during any 1-hour period when equipment is actively transmitting. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may allow a higher value for “Duty cycle”. ( 8 ) Social alarm devices are used to assist elderly or disabled people when they are in distress. ( 9 ) This category covers, for example, devices for car immobilisation, animal identification, alarm systems, cable detection, waste management, personal identification, wireless voice links, access control, proximity sensors, anti-theft systems, including RF anti-theft induction systems, data transfer to handheld devices, automatic article identification, wireless control systems and automatic road tolling. ( 10 ) This category covers inductive applications used for Radio Frequency Identification (RFID). ( 11 ) This category covers inductive applications used for Electronic Article Surveillance (EAS). ( 12 ) This category covers the radio part of active implantable medical devices, as defined in Council Directive 90/385/EEC of 20 June 1990 on the approximation of the laws of the Member States relating to active implantable medical devices ( OJ L 189, 20.7.1990, p. 17 ). ( 13 ) This category covers systems specifically designed for the purpose of providing non-voice digital communications between active medical implants, as defined in footnote 12, and/or body-worn devices and other devices external to the human body used for transferring non-time critical individual patient-related physiological information. ( 14 ) This category covers transmitting devices which are placed inside the body of an animal for the purpose of performing diagnostic functions and/or delivery of therapeutic treatment. ( 15 ) This category includes applications which connect personal audio devices, including mobile phones, and the automotive or home entertainment system. ( 16 ) Applications for wireless audio systems, including: wireless microphones, cordless loudspeakers; cordless headphones; cordless headphones for portable use, e.g. portable CD, cassette or radio devices carried on a person; cordless headphones for use in a vehicle, for example for use with a radio or mobile telephone, etc.; in-ear monitoring and wireless microphones for use at concerts or other stage productions. ( 17 ) This category covers applications used for determining the position, velocity and/or other characteristics of an object, or for obtaining information relating to these parameters. ( 18 ) Tank Level Probing Radars (TLPR) are a specific type of radiodetermination application, which are used for tank level measurements and are installed in metallic or reinforced concrete tanks, or similar structures made of material with comparable attenuation characteristics. The purpose of the tank is to contain a substance. ( 19 ) The power limit applies inside a closed tank and corresponds to a spectral density of – 41,3 dBm/MHz e.i.r.p. outside a 500 litre test tank. ( 20 ) This category covers applications used to control the movement of models (principally miniature representations of vehicles) in the air, on land or over or under the water surface.’
Other acts of the same type
Council Decision (CFSP) 2015/2216 of 30 November 2015 amending Decision 2010/413/CFSP concerning restrictive measures against IranCouncil Decision (EU) 2015/2288 of 30 November 2015 on the financial contributions to be paid by Member States to finance the European Development Fund, including the ceiling for 2017, the amount for 2016, the first instalment for 2016 and an indicative and non-binding forecast for the expected annual amounts for the years 2018 and 2019Council Decision (EU) 2015/2312 of 30 November 2015 on the signing, on behalf of the European Union, and provisional application of the Sustainable Fisheries Partnership Agreement between the European Union and the Republic of Liberia and the Implementation Protocol theretoCouncil Decision (EU) 2015/2367 of 30 November 2015 on the position to be taken on behalf of the European Union within the Joint Veterinary Committee set up by the Agreement between the European Community and the Swiss Confederation on trade in agricultural products in relation to Decision No 1/2015 regarding the amendment of Appendices 1, 2, 3, 4, 5, 6, 7, 10 and 11 to Annex 11 to the AgreementCouncil Decision (EU) 2015/2236 of 27 November 2015 establishing the position to be taken on behalf of the European Union within the Ministerial Conference of the World Trade Organisation as regards an extension of the moratorium on customs duties on electronic transmissions and the moratorium on non-violation and situation complaintsCommission Decision (EU) 2017/166 of 27 November 2015 on State aid SA.38831 (2014/C) (ex 2014/N) which Portugal is planning to implement for Volkswagen Autoeuropa, Lda (notified under document C(2015) 8232) (Text with EEA relevance. )Commission Implementing Decision (EU) 2015/2250 of 26 November 2015 confirming or amending the average specific emissions of CO2 and specific emissions targets for manufacturers of new light commercial vehicles for the calendar year 2014 pursuant to Regulation (EU) No 510/2011 of the European Parliament and of the Council (notified under document C(2015) 8346)Commission Implementing Decision (EU) 2015/2251 of 26 November 2015 confirming or amending the average specific emission of CO2 and specific emissions targets for manufacturers of passenger cars for the calendar year 2014 pursuant to Regulation (EC) No 443/2009 of the European Parliament and of the Council (notified under document C(2015) 8348)Commission Delegated Decision (EU) 2016/309 of 26 November 2015 on the equivalence of the supervisory regime for insurance and reinsurance undertakings in force in Bermuda to the regime laid down in Directive 2009/138/EC of the European Parliament and of the Council and amending Comission Delegated Decision (EU) 2015/2290Commission Delegated Decision (EU) 2016/310 of 26 November 2015 on the equivalence of the solvency regime for insurance and reinsurance undertakings in force in Japan to the regime laid down in Directive 2009/138/EC of the European Parliament and of the CouncilCommission Implementing Decision (EU) 2015/2186 of 25 November 2015 establishing a format for the submission and making available of information on tobacco products (notified under document C(2015) 8162) (Text with EEA relevance)Commission Implementing Decision (EU, Euratom) 2015/2187 of 25 November 2015 amending Decision 2005/816/EC, Euratom authorising the Republic of Estonia to use certain approximate estimates for the calculation of the VAT own resources base (notified under document C(2015) 8172)
Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.
What to look at next
Browse all EU Legal ActsEvery instrument by type and year, full text free to read section by sectionEuropean Union legislationEU Legal Acts by type and yearGrouped by instrument type and year of enactment, so you can find others of the same kindBrowse by type and yearEuropean Union: what this database coversWhich datasets are here, which official source they come from, and how current they areEuropean Union overview