My bookmarksSign up free
Source

Commission Regulation (EU) 2018/932 of 29 June 2018 amending Regulation (EU) No 582/2011 as regards the provisions on testing by means of portable emission measurement systems (PEMS) and the requirements for universal fuel range type-approval (Text with EEA relevance.)

Commission Regulation (EU) 2018/932 of 29 June 2018 amending Regulation (EU) No 582/2011 as regards the provisions on testing by means of portable emission measurement systems (PEMS) and the requirements for universal fuel range type-approval (Text with EEA relevance.)

Regulation (EU) 2018/932 · Regulation · 2 articles

Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗

Article 1

Open ↗

Regulation (EU) No 582/2011 is amended as follows: (1) Annex I is amended as follows: (a) in point 1.1.2, the introductory part of the first paragraph is replaced by the following: ‘If the manufacturer permits the engine family to run on market fuels that do not comply either with Directive 98/70/EC of the European Parliament and of the Council  ( *1 ) , or with CEN standard EN 228:2012 in the case of unleaded petrol or CEN standard EN 590:2013 in the case of diesel, such as running on FAME B100 (CEN standard EN 14214), FAME diesel blends B20/B30 (CEN standard EN 16709), paraffinic fuel (CEN standard EN 15940) or others, the manufacturer shall, in addition to the requirements in point 1.1.1, comply with the following requirements: ( *1 )   Directive 98/70/EC of the European Parliament and of the Council of 13 October 1998 relating to the quality of petrol and diesel fuels and amending Council Directive 93/12/EEC ( OJ L 350, 28.12.1998, p. 58 ).’;" (b) in point 1.1.2, the following point (a1) is inserted: ‘(a1) determine the power correction factor for each fuel declared pursuant to point 5.2.7 if applicable;’; (c) in point 5.2.5, point (b) is replaced by the following: ‘(b) 10 % when performing the World Harmonised Steady state Cycle (hereinafter “WHSC”) test in accordance with Annex III, except for mode 1 and 13 (idle modes)’; (d) the following point 5.2.7 is inserted: ‘5.2.7. If the difference between the measured torque value obtained with a declared market fuel and the torque calculated from the information requested in point 5.2.1 exceeds any of the values specified in point 5.2.5, a power correction factor for each additional market fuel permitted by the manufacturer in accordance with point 1.1.2 shall be determined for the engine family. The correction factor shall be calculated as the ratio between average measured peak torque [Nm] on the reference fuel according to Annex IX, and average measured peak torque [Nm] on the market fuel declared.’; (e) points 5.3.3 and 5.3.3.1 are replaced by the following: ‘5.3.3. The fulfilment of the requirement referred to in point 5.2.5 shall be demonstrated for the parent engine of an engine family when determining the engine power in accordance with Annex XIV and when performing the WHSC test in accordance with Annex III and off-cycle laboratory testing at type-approval in accordance with Section 6 of Annex VI. 5.3.3.1. The fulfilment of the requirement referred to in point 5.2.5 shall be demonstrated for each engine family member when determining the engine power in accordance with Annex XIV. For that purpose, additional measurements shall be performed at several part load and engine speed operating points (for example at the modes of the WHSC and some additional random points).’; (f) the following point 5.3.3.2 is inserted: ‘5.3.3.2. If applicable, the power correction factor for the engine family, as referred to in point 5.2.7, shall be determined with the parent engine of the engine family.’; (g) in Appendix 5, in the Addendum to EC type-approval certificate, point 1.5.2 is replaced by the following: ‘1.5.2. Additional data, e.g. the power correction factor for each fuel declared (if applicable)’; (h) in Appendix 7, in the Addendum to EC type-approval certificate, point 1.5.2 is replaced by the following: ‘1.5.2. Additional data, e.g. the power correction factor for each fuel declared (if applicable)’; (2) Annex II is amended as follows: (a) point 4.4.2 is replaced by the following: ‘4.4.2.    Fuel The test fuel shall be market fuel covered by Directive 98/70/EC and the relevant CEN standards, or reference fuel as specified in Annex IX to this Regulation.’; (b) the following point 4.4.2.2 is inserted: ‘4.4.2.2. Fuel samples shall be taken.’; (c) point 4.5.3 is replaced by the following: ‘4.5.3. For N 3 vehicles the trip shall consist of approximately 30 % urban, 25 % rural and 45 % motorway operation.’; (d) point 4.6.5 is replaced by the following: ‘4.6.5. The test duration shall be long enough to complete between four and eight times the work performed during the WHTC or produce between four and eight times the CO 2 reference mass in kg/cycle from the WHTC as applicable.’; (e) Appendix 1 is amended as follows: (i) the following point 4.2.1.1 is inserted: ‘4.2.1.1.   Calculation of the specific emissions for a declared market fuel If a test pursuant to this Annex was performed with a market fuel declared in point 3.2.2.2.1 of Part 1 in Appendix 4 to Annex I, the specific emissions e gas (mg/kWh) shall be calculated for each window and each pollutant by multiplication of the uncorrected specific emissions with the power correction factor determined pursuant to point 1.1.2 (a1) of Annex I.’; (ii) point 4.2.2.2.2 is replaced by the following: ‘4.2.2.2.2. The test shall be void if the percentage of valid windows is less than 50 % or if there are no valid windows in respect of nitrogen oxides (NO x ) left in urban only operations after the 90 percentile rule has been applied.’; (f) in Appendix 4, the following point 2.1.1 is inserted: ‘2.1.1. If a market fuel declared in point 3.2.2.2.1 of Part 1 in Appendix 4 to Annex I is used for the test, the ECU torque signal shall be divided by the correction factor prior to the verification with the reference maximum torque curve performed with that market fuel.’.

Article 2

Open ↗

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union .

Other acts of the same type
Council Implementing Regulation (EU) 2022/1009 of 27 June 2022 implementing Regulation (EC) No 1183/2005 concerning restrictive measures in view of the situation in the Democratic Republic of the CongoCouncil Implementing Regulation (EU) 2022/1010 of 27 June 2022 implementing Regulation (EU) No 267/2012 concerning restrictive measures against IranCommission Implementing Regulation (EU) 2022/1013 of 27 June 2022 imposing a definitive anti-dumping duty on imports of certain ring binder mechanisms originating in the People’s Republic of China and as extended to Vietnam and Lao People’s Democratic Republic following an expiry review pursuant to Article 11(2) of Regulation (EU) 2016/1036 of the European Parliament and of the CouncilCommission Implementing Regulation (EU) 2022/1106 of 27 June 2022 entering a name in the register of protected designations of origin and protected geographical indications (‘Queso de Acehúche’ (PDO))Commission Delegated Regulation (EU) 2022/1450 of 27 June 2022 supplementing Regulation (EU) 2018/848 of the European Parliament and of the Council as regards the use of non organic protein feed for the production of organic livestock due to Russia’s invasion of Ukraine (Text with EEA relevance)Commission Delegated Regulation (EU) 2023/181 of 27 June 2022 correcting certain language versions of Delegated Regulation (EU) 2016/1149 supplementing Regulation (EU) No 1308/2013 of the European Parliament and of the Council as regards the national support programmes in the wine sector and amending Commission Regulation (EC) No 555/2008Council Implementing Regulation (EU) 2022/994 of 24 June 2022 implementing Regulation (EU) 2022/879 amending Regulation (EU) No 833/2014 concerning restrictive measures in view of Russia’s actions destabilising the situation in UkraineCommission Implementing Regulation (EU) 2022/978 of 23 June 2022 amending Implementing Regulation (EU) 2019/159 imposing a definitive safeguard measure on imports of certain steel productsCommission Implementing Regulation (EU) 2022/980 of 23 June 2022 amending Implementing Regulation (EU) No 75/2013 as regards the additional import duties in the sugar sectorCommission Implementing Regulation (EU) 2022/981 of 23 June 2022 amending Implementing Regulation (EU) 2021/546 imposing a definitive anti-dumping duty and definitively collecting the provisional duty imposed on imports of aluminium extrusions originating in the People’s Republic of ChinaRegulation (EU) 2022/1031 of the European Parliament and of the Council of 23 June 2022 on the access of third-country economic operators, goods and services to the Union’s public procurement and concession markets and procedures supporting negotiations on access of Union economic operators, goods and services to the public procurement and concession markets of third countries (International Procurement Instrument – IPI) (Text with EEA relevance)Commission Implementing Regulation (EU) 2022/976 of 22 June 2022 amending Annexes V and XIV to Implementing Regulation (EU) 2021/404 as regards the entries for Canada, the United Kingdom and the United States in the lists of third countries authorised for the entry into the Union of consignments of poultry, germinal products of poultry and fresh meat of poultry and game birds (Text with EEA relevance)

Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.

Contents

What to look at next