My bookmarksSign up free

Regulation (EU) 2019/129 of the European Parliament and of the Council of 16 January 2019 amending Regulation (EU) No 168/2013 as regards the application of the Euro 5 step to the type-approval of two- or three-wheel vehicles and quadricycles

Regulation (EU) 2019/129 of the European Parliament and of the Council of 16 January 2019 amending Regulation (EU) No 168/2013 as regards the application of the Euro 5 step to the type-approval of two- or three-wheel vehicles and quadricycles

Regulation (EU) 2019/129 · Regulation · 3 articles

Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗

General requirements of on-board diagnostic systems

Article 1

Regulation (EU) No 168/2013 is amended as follows: (1) Article 21 is replaced by the following: ‘Article 21 General requirements of on-board diagnostic systems 1.   L-category vehicles, with the exception of L1e, L2e and L6e vehicles, shall be equipped with an OBD system which complies with the functional requirements and test procedures laid down in the delegated acts referred to in paragraph 8 and as from the application dates set out in Annex IV. 2.   From the dates set out in point 1.8.1 of Annex IV, vehicle categories and subcategories L3e, L4e, L5e-A and L7e-A shall be equipped with an OBD stage I system which monitors any electric circuit and electronics failure of the emission control system and reports those failures which result in the emission thresholds laid down in Annex VI (B1) being exceeded. 3.   From the dates set out in point 1.8.2 of Annex IV, vehicle categories and subcategories L3e, L4e, L5e and L7e shall be equipped with an OBD stage I system which monitors any electric circuit and electronics failure of the emission control system and which triggers a report when the emission thresholds laid down in Annex VI (B1) are exceeded. OBD stage I systems for those vehicle categories and subcategories shall also report the triggering of any operating mode which significantly reduces engine torque. 4.   From the dates set out in point 1.8.3 of Annex IV, vehicle categories L3e, L4e, L5e and L7e shall be equipped with an OBD stage I system which monitors any electric circuit and electronics failure of the emission control system and which triggers a report when the emission thresholds laid down in Annex VI (B2) are exceeded. OBD stage I systems for those vehicle categories shall also report the triggering of any operating mode which significantly reduces engine torque. 5.   From the dates set out in point 1.8.4 of Annex IV, vehicle categories and subcategories L3e, L4e, L5e-A and L7e-A shall in addition be equipped with an OBD stage II system which monitors and reports emission control system failures and degradation, with the exception of catalyst monitoring, which result in the OBD emission thresholds laid down in Annex VI (B1) being exceeded. 6.   From the dates set out in point 1.8.5 of Annex IV, vehicle categories and subcategories L3e, L4e, L5e-A and L7e-A shall in addition be equipped with an OBD stage II system which monitors and reports emission control system failures and degradation which result in the OBD emission thresholds laid down in Annex VI (B2) being exceeded. 7.   Paragraphs 5 and 6 shall not apply to enduro motorcycles in subcategory L3e-AxE and trial motorcycles in subcategory L3e-AxT. 8.   In order to harmonise the OBD system reporting of functional safety or emission control system faults and facilitate effective and efficient repair of a vehicle, the Commission is empowered to adopt delegated acts in accordance with Article 75 supplementing this Regulation by laying down the detailed technical requirements related to on-board diagnostics with respect to vehicle categories and subcategories as set out in Annex II, C1 – Vehicle construction and general type-approval requirements, the row relating to No 11, including functional OBD requirements and test procedures for the subjects listed in paragraphs 1 to 7 of this Article, and the detailed technical requirements related to test type VIII referred to in Annex V.’; (2) in Article 23(3), point (c) is replaced by the following: ‘(c) mathematical durability procedure: Until 31 December 2024, for each emission constituent, the product of the multiplication of the deterioration factor set out in Annex VII (B) and the environmental performance test result of a vehicle which has accumulated more than 100 km after it was first started at the end of the production line shall be lower than the environmental performance test limit set out in Annex VI (A). Notwithstanding the first subparagraph, for new types of vehicles from 1 January 2020 and for existing types of vehicles from 1 January 2021 until 31 December 2024, for each emission constituent the product of the multiplication of the deterioration factor set out in Annex VII (B) and the environmental performance test result of a vehicle which has accumulated more than 2 500 km for a vehicle with a maximum design vehicle speed of < 130 km/h and 3 500 km for a vehicle with a maximum design vehicle speed of ≥ 130 km/h after it was first started at the end of the production line shall be lower than the tailpipe emission limit set out in Annex VI (A).’; (3) in Article 30(1), point (b) is replaced by the following: ‘(b) the test results sheet;’; (4) in Article 44(1), the second subparagraph is replaced by the following: ‘The first subparagraph shall apply only to vehicles within the territory of the Union which were covered by a valid EU type-approval at the time of their production, but which neither were registered nor entered into service before that EU type-approval lost its validity.’; (5) Article 75(2) is replaced by the following: ‘2.   The power to adopt delegated acts referred to in Article 18(3), Article 20(2), Article 21(8), Article 22(5) and (6), Article 23(6) and (12), Article 24(3), Article 25(8), Article 32(6), Article 33(6), Article 50(4), Article 54(3), Article 57(12), Article 65 and Article 74 shall be conferred on the Commission for a period of five years from 22 March 2013. The delegation of power shall be tacitly extended for periods of five years, unless the European Parliament or the Council opposes such extension not later than three months before the end of each period. The Commission shall draw up a report in respect of the delegation of power not later than 22 June 2022 and nine months before the end of each following five-year period.’; (6) Annexes II, IV, V and VI are amended in accordance with the Annex to this Regulation.

Article 2

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union .

Supplementary provisions

ANNEXSupplementary provisions

ANNEX Annexes II, IV, V and VI to Regulation (EU) No 168/2013 are amended as follows: (1) in Annex II, section C1, in the row relating to No 11, the sign ‘X’ is deleted for subcategories L6e-A and L6e-B; (2) in Annex IV, the table is amended as follows: (a) points 1.1.2.1, 1.1.2.2 and 1.1.2.3 are replaced by the following: ‘1.1.2.1 Euro 4: Annex VI A1 L1e, L2e, L6e 1.1.2017 1.1.2018 31.12.2020; for L2e-U and L6e-B: 31.12.2024 1.1.2.2. Euro 4: Annex VI A1 L3e, L4e, L5e, L7e 1.1.2016 1.1.2017 31.12.2020; for L3e-AxE and L3e-AxT 31.12.2024 1.1.2.3. Euro 5: Annex VI A2 L1e-L7e 1.1.2020; for L2e-U, L3e-AxE, L3e-AxT and L6e-B: 1.1.2024 1.1.2021; for L2e-U, L3e-AxE, L3e-AxT and L6e-B: 1.1.2025’;   (b) points 1.8.1, 1.8.2 and 1.8.3 are replaced by the following: ‘1.8.1. OBD stage I functional requirements L3e, L4e, L5e-A, L7e-A 1.1.2016 1.1.2017 31.12.2020 OBD stage I environmental test procedure (test type VIII) OBD stage I environmental test thresholds, Annex VI (B1) 1.8.2 OBD stage I functional requirements including any operating mode which significantly reduces engine torque L3e, L4e, L5e, L7e 1.1.2020 1.1.2021 31.12.2024 OBD stage I environmental test procedure (test type VIII) OBD stage I environmental test thresholds, Annex VI (B1) 1.8.3 OBD stage I functional requirements including any operating mode which significantly reduces engine torque L3e, L4e, L5e, L7e 1.1.2024 1.1.2025’   OBD stage I environmental test procedure (test type VIII) OBD stage I environmental test thresholds, Annex VI (B2) (c) the following points are inserted: ‘1.8.4. OBD stage II functional requirements with the exception of catalyst monitoring L3e (except L3e-AxE and L3e-AxT), L4e, L5e-A, L7e-A 1.1.2020 1.1.2021 31.12.2024 OBD stage II environmental test procedures (test type VIII) OBD stage II environmental test thresholds, Annex VI (B1) 1.8.5. OBD stage II functional requirements, L3e (except L3e-AxE and L3e-AxT), L4e, L5e-A, L7e-A 1.1.2024 1.1.2025’   OBD stage II environmental test procedures (test type VIII), OBD stage II environmental test thresholds, Annex VI (B2) (d) points 1.9.1 and 1.9.2 are replaced by the following: ‘1.9.1. Sound level test procedure and limit values Annex VI (D) L1e, L2e, L6e 1.1.2017 1.1.2018   1.9.2. Sound level test procedure and limit values ( 3 ), Annex VI (D) L3e, L4e, L5e, L7e 1.1.2016 1.1.2017’   (e) point 1.9.4 is replaced by the following: ‘1.9.4. UNECE regulations Nos 9, 41, 63, 92 and associated new limit values proposed by the Commission L1e-L7e’       (3) in Annex V, section B, the content of the cell in the first column, second row, is replaced by the following: ‘Type I test ( 19 ) Particulate mass (Euro 5 only)’; (4) Annex VI is amended as follows: (a) in section B1, the first row, referring to Vehicle category ‘L6e-A’, is deleted; (b) in section B2, first row: (i) the words ‘L3e-L7e ( 6 )’ are replaced by the following: ‘L3e, L4e, L5e, L7e’; (ii) the words ‘All L category vehicles except category L1e and L2e’ are replaced by the following: ‘All L category vehicles except category L1e, L2e and L6e’.

Other acts of the same type
Commission Implementing Regulation (EU) 2025/2291 of 10 November 2025 amending Implementing Regulation (EU) 2022/1629 as regards the list of demarcated areas for containment of Ceratocystis platani (J.M. Walter) Engelbr. & T.C. Harr. in Greece, France and ItalyCommission Implementing Regulation (EU) 2025/2293 of 10 November 2025 amending Implementing Regulation (EU) 2023/203 as regards the requirements applicable to organisations subject to a declaration and correcting Regulations (EU) No 1178/2011, (EU) No 748/2012, (EU) No 965/2012, (EU) No 139/2014, (EU) No 1321/2014, (EU) 2015/340, and Implementing Regulation (EU) 2017/373Commission Implementing Regulation (EU) 2025/2294 of 10 November 2025 adopting a temporary derogation from the requirements concerning the introduction into the Union territory of fruits of Mangifera L. originating in Mali and amending Implementing Regulation (EU) 2019/2072Commission Implementing Regulation (EU) 2025/2315 of 10 November 2025 approving a Union amendment to the product specification of the protected geographical indication Scottish Farmed Salmon pursuant to Regulation (EU) 2024/1143 of the European Parliament and of the CouncilCommission Implementing Regulation (EU) 2025/2317 of 10 November 2025 on the registration of the geographical indication İpsala Pirinci (PDO) in the Union register of geographical indications pursuant to Regulation (EU) 2024/1143 of the European Parliament and of the CouncilCommission Implementing Regulation (EU) 2025/2318 of 10 November 2025 on the registration of the geographical indication Bursa Kestane Şekeri (PGI) in the Union register of geographical indications pursuant to Regulation (EU) 2024/1143 of the European Parliament and of the CouncilCommission Implementing Regulation (EU) 2025/2242 of 7 November 2025 authorising the placing on the market of yellow tomato extract as a novel food and amending Implementing Regulation (EU) 2017/2470Commission Implementing Regulation (EU) 2025/2245 of 7 November 2025 amending Implementing Regulation (EU) 2017/2470 as regards the conditions of use of the novel food Schizochytrium sp. (ATCC PTA-9695) oilCommission Implementing Regulation (EU) 2025/2246 of 7 November 2025 amending Implementing Regulation (EU) 2022/932 as regards minimum control frequenciesCommission Delegated Regulation (EU) 2026/118 of 7 November 2025 supplementing Directive (EU) 2017/2397 of the European Parliament and of the Council by laying down standards for competences and corresponding knowledge and skills, for practical examinations, for the approval of simulators and for medical fitness and repealing Commission Delegated Directive (EU) 2020/12Commission Implementing Regulation (EU) 2025/2233 of 6 November 2025 authorising the placing on the market of Clostridium butyricum TO-A as a novel food and amending Implementing Regulation (EU) 2017/2470Commission Implementing Regulation (EU) 2025/2235 of 6 November 2025 amending Implementing Regulation (EU) 2025/1082 as regards Potato virus S and Potato virus X as specified pests for unrooted cuttings for planting of Calibrachoa spp., Petunia spp. and their hybrids from Kenya

Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.

What to look at next