Commission Implementing Regulation (EU) 2023/2087 of 28 September 2023 granting a Union authorisation for the biocidal product family ‘Lysoform IPA Surface’ in accordance with Regulation (EU) No 528/2012 of the European Parliament and of the Council (Text with EEA relevance)
Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗
A Union authorisation with authorisation number EU-0030790-0000 is hereby granted to Lysoform Dr Hans Rosemann GmbH for the making available on the market and use of the same biocidal product family ‘Lysoform IPA Surface’ in accordance with the summary of the biocidal product characteristics set out in the Annex. The Union authorisation is valid from 19 October 2023 until 30 November 2030.
This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union .
Summary of product characteristics for a biocidal product family
ANNEX Summary of product characteristics for a biocidal product family Lysoform IPA Surface Product type 2 – Disinfectants and algaecides not intended for direct application to humans or animals (Disinfectants) Product type 4 – Food and feed area (Disinfectants) Authorisation number: EU-0030790-0000 R4BP asset number: EU-0030790-0000 PART I FIRST INFORMATION LEVEL 1. ADMINISTRATIVE INFORMATION 1.1. Family name Name Lysoform IPA Surface 1.2. Product type(s) Product type(s) PT02 – Disinfectants and algaecides not intended for direct application to humans or animals (Disinfectants) PT04 – Food and feed area (Disinfectants) 1.3. Authorisation holder Name and address of the authorisation holder Name Lysoform Dr Hans Rosemann GmbH Address Kaiser-Wilhelm-Str. 133, 12247 Berlin Germany Authorisation number EU-0030790-0000 R4BP asset number EU-0030790-0000 Date of the authorisation 19 October 2023 Expiry date of the authorisation 30 November 2030 1.4. Manufacturer(s) of the biocidal products Name of manufacturer Lysoform Dr Hans Rosemann GmbH Address of manufacturer Kaiser-Wilhelm-Straße 133, 12247 Berlin Germany Location of manufacturing sites Kaiser-Wilhelm-Straße 133, 12247 Berlin Germany Name of manufacturer Imeco Address of manufacturer Boschstr. 5, 63768 Hösbach Germany Location of manufacturing sites Boschstr. 5, 63768 Hösbach Germany Neue Straße 2-4, 09471 Köningswalde Germany Name of manufacturer A.F.P. GmbH Address of manufacturer Otto Brenner Straße 16, 21337 Lüneburg Germany Location of manufacturing sites Otto Brenner Straße 16, 21337 Lüneburg Germany Name of manufacturer Sterisol AB Address of manufacturer Kronoängsgatan 3, 592 23 Vadstena Sweden Location of manufacturing sites Kronoängsgatan 3, 592 23 Vadstena Sweden Name of manufacturer WHR GmbH Address of manufacturer Am Galgenturm 2, 97638 Mellrichstadt Germany Location of manufacturing sites Am Galgenturm 2, 97638 Mellrichstadt Germany Name of manufacturer Hygan GmbH | Srl Address of manufacturer Meucci-Str. 5, 39055 Leifers | Laives (BZ) Italy Location of manufacturing sites Meucci-Str. 5, 39055 Leifers | Laives (BZ) Italy Name of manufacturer Laboratoire Sarbec SA Address of manufacturer 10 rue du Vertuquet, 59960 Neuville-en-Ferrain France Location of manufacturing sites 10 rue du Vertuquet, 59960 Neuville-en-Ferrain France Name of manufacturer Dr Schumacher GmbH Address of manufacturer Am Roggenfeld 3, 34323 Malsfeld Germany Location of manufacturing sites Am Roggenfeld 3, 34323 Malsfeld Germany Jeleniogórska 12, 59-800 Lubań Poland 1.5. Manufacturer(s) of the active substance(s) Active substance Propan-2-ol Name of manufacturer Ineos Solvents Germany GmbH (formerly Sasol) Address of manufacturer Römerstraße 733, 47443 Moers Germany Location of manufacturing sites Römerstraße 733, 47443 Moers Germany Shamrockstr. 88, 44643 Herne Germany Active substance Propan-2-ol Name of manufacturer Shell Chemicals Europe B.V. Address of manufacturer Postbus 2334, 3000 CH Rotterdam Netherlands Location of manufacturing sites Shell Nederland Raffinaderij B.V., Vondelingenweg 601, 3196 KK Rotterdam-Pernis Netherlands 2. PRODUCT FAMILY COMPOSITION AND FORMULATION 2.1. Qualitative and quantitative information on the composition of the family Common name IUPAC name Function CAS number EC number Content (%) Min Max Propan-2-ol Active Substance 67-63-0 200-661-7 63,1 63,1 2.2. Type(s) of formulation Formulation(s) Any other liquid (AL), ready-to-use Any other liquid (AL), ready-to-use, wipes impregnated with disinfectant formulation PART II SECOND INFORMATION LEVEL – META SPC(S) META SPC 1 1. META SPC 1 ADMINISTRATIVE INFORMATION 1.1. Meta SPC 1 identifier Identifier Superficid® 1.2. Suffix to the authorisation number Number 1-1 1.3. Product type(s) Product type(s) PT02 – Disinfectants and algaecides not intended for direct application to humans or animals (Disinfectants) PT04 – Food and feed area (Disinfectants) 2. META SPC 1 COMPOSITION 2.1. Qualitative and quantitative information on the composition of the meta SPC 1 Common name IUPAC name Function CAS number EC number Content (%) Min Max Propan-2-ol Active Substance 67-63-0 200-661-7 63,1 63,1 2.2. Type(s) of formulation of the meta SPC 1 Formulation(s) Any other liquid (AL), ready-to-use 3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 1 Hazard statements Highly flammable liquid and vapour. Causes serious eye irritation. May cause drowsiness or dizziness. Repeated exposure may cause skin dryness or cracking. Precautionary statements Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. – No smoking. Keep container tightly closed. Ground and bond container and receiving equipment. Use explosion-proof electrical/ventilating/lighting equipment. Use non-sparking tools. Take action to prevent static discharges. Avoid breathing vapours. Avoid breathing spray. Use only outdoors or in a well-ventilated area. Wear eye protection. IF IN EYES:Rinse cautiously with water for several minutes.Remove contact lenses, if present and easy to do. Continue rinsing. Call a POISON CENTER or doctor if you feel unwell. If eye irritation persists:Get medical advice. If eye irritation persists:Get medical attention. In case of fire:Use alcohol-resistant foam, carbon dioxide or water mist to extinguish. Store in a well-ventilated place.Keep cool. Store locked up. Dispose of contents to/container to an approved waste disposal plant. 4. AUTHORISED USE(S) OF THE META SPC 1 4.1. Use description Table 1 Use # 1 disinfection of surfaces – spraying Product type PT02 – Disinfectants and algaecides not intended for direct application to humans or animals (Disinfectants) Where relevant, an exact description of the authorised use - Target organism(s) (including development stage) Scientific name: Bacteria Common name: - Development stage: - Scientific name: Yeast Common name: - Development stage: - Field(s) of use Indoor Disinfection of clean non-porous surfaces such as small work surfaces in medical and non-medical areas as well as surfaces in cleanrooms (class A/B) Application method(s) Method: Spraying Detailed description: Product will be sprayed directly on the surface. Application rate(s) and frequency Application Rate: Ready-to-use. Do not apply more than 25 ml/m 2 . Dilution (%): - Number and timing of application: - Category(ies) of users Industrial Professional Pack sizes and packaging material Bottle: 125-1 000 ml packaging material: HDPE Clack cap material: PP; Fine mist-sprayer: complex system (PE-LD, PP, PBT, POM, EVA, stainless steel); Spray head: complex system (PP, PE, POM, Synthetic oil, Silicon oil) 4.1.1. Use-specific instructions for use Spray ready-to-use product onto the surfaces and allow to take effect for at least 1 minute at room temperature (20 ± 2 °C). 4.1.2. Use-specific risk mitigation measures The following personal risk mitigation measure can be applied for refilling procedure unless it can be replaced by technical and/or organisational measures: Wear eye protection during handling of the product. 4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging 4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 4.2. Use description Table 2 Use # 2 – disinfection of surfaces – wiping Product type PT02 – Disinfectants and algaecides not intended for direct application to humans or animals (Disinfectants) Where relevant, an exact description of the authorised use - Target organism(s) (including development stage) Scientific name: Bacteria Common name: - Development stage: - Scientific name: Yeast Common name: - Development stage: - Field(s) of use Indoor Disinfection of clean non-porous surfaces such as small work surfaces in medical and non-medical areas as well as surfaces in cleanrooms (class A/B) Application method(s) Method: Wiping Detailed description: Product is applied on wipes by pouring, spraying or soaking and the surface is thoroughly wiped with the soaked wipe afterwards (wet-wiping). Application rate(s) and frequency Application Rate: Ready-to-use. Do not apply more than 25 ml/m 2 . Dilution (%): - Number and timing of application: - Category(ies) of users Industrial Professional Pack sizes and packaging material Bottle: 125-1 000 ml packaging material: HDPE Clack cap material: PP Fine mist-sprayer: complex system (PE-LD, PP, PBT, POM, EVA, stainless steel); Spray head: complex system (PP, PE, POM, Synthetic oil, Silicon oil) Canister: 5-30 L packaging material: HDPE closure material: HDPE 4.2.1. Use-specific instructions for use Apply the ready-to-use product on wipes by pouring, spraying or soaking and wipe the surface thoroughly with the wet wipe (wet-wiping). Allow to take effect for at least 5 minutes at room temperature (20 ± 2 °C). 4.2.2. Use-specific risk mitigation measures The following personal risk mitigation measure can be applied for refilling procedure unless it can be replaced by technical and/or organisational measures: Wear eye protection during handling of the product. 4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging 4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 4.3. Use description Table 3 Use # 3 – disinfection of surfaces with food and feed contact – spraying Product type PT04 – Food and feed area (Disinfectants) Where relevant, an exact description of the authorised use - Target organism(s) (including development stage) Scientific name: Bacteria Common name: - Development stage: - Scientific name: Yeast Common name: - Development stage: - Scientific name: Viruses Common name: - Development stage: - Field(s) of use Indoor Disinfection of clean non-porous surfaces in kitchens and food industry including cleanrooms (class A/B) Application method(s) Method: Spraying Detailed description: Product will be sprayed directly on the surface. Application rate(s) and frequency Application Rate: Ready-to-use. Do not apply more than 25 ml/m 2 . Dilution (%): - Number and timing of application: - Category(ies) of users Industrial Professional Pack sizes and packaging material Bottle: 125-1 000 ml packaging material: HDPE Clack cap material: PP Fine mist-sprayer: complex system (PE-LD, PP, PBT, POM, EVA, stainless steel) Spray head: complex system (PP, PE, POM, Synthetic oil, Silicon oil) 4.3.1. Use-specific instructions for use Spray ready-to-use product onto the surface and allow to take effect at room temperature (20 ± 2 °C) for at least 1 (bactericidal and yeasticidal activity) or 2 minutes (virucidal activity). 4.3.2. Use-specific risk mitigation measures The following personal risk mitigation measure can be applied for disinfection of food processing machinery and for refilling procedure unless it can be replaced by technical and/or organisational measures: Wear eye protection during handling of the product. 4.3.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.3.4. Where specific to the use, the instructions for safe disposal of the product and its packaging 4.3.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 4.4. Use description Table 4 Use # 4 – disinfection of surfaces with food and feed contact – wiping Product type PT04 – Food and feed area (Disinfectants) Where relevant, an exact description of the authorised use - Target organism(s) (including development stage) Scientific name: Bacteria Common name: - Development stage: - Scientific name: Yeast Common name: - Development stage: - Scientific name: Viruses Common name: - Development stage: - Field(s) of use Indoor Disinfection of clean non-porous surfaces in kitchens and food industry including cleanrooms (class A/B) Application method(s) Method: Wiping Detailed description: Product is applied on wipes by pouring, spraying or soaking and the surface is thoroughly wiped with the soaked wipe afterwards (wet-wiping). Application rate(s) and frequency Application Rate: Ready-to-use. Do not apply more than 25 ml/m 2 . Dilution (%): - Number and timing of application: - Category(ies) of users Industrial Professional Pack sizes and packaging material Bottle: 125-1 000 ml packaging material: HDPE Clack cap material: PP Fine mist-sprayer: complex system (PE-LD, PP, PBT, POM, EVA, stainless steel); Spray head: complex system (PP, PE, POM, Synthetic oil, Silicon oil) Canister: 5-30 L packaging material: HDPE closure material: HDPE 4.4.1. Use-specific instructions for use Apply the ready-to-use product on wipes by pouring, spraying or soaking and wipe the surface thoroughly with the wet wipe (wet-wiping). Allow to take effect for at least 5 minutes at room temperature (20 ± 2 °C). 4.4.2. Use-specific risk mitigation measures The following personal risk mitigation measure can be applied for disinfection of food processing machinery and for refilling procedure unless it can be replaced by technical and/or organisational measures: Wear eye protection during handling of the product. 4.4.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.4.4. Where specific to the use, the instructions for safe disposal of the product and its packaging 4.4.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 5. GENERAL DIRECTIONS FOR USE ( 1 ) OF THE META SPC 1 5.1. Instructions for use Clean the surface carefully before use. Remove excess water from the surface before disinfection, if appropriate. Do not apply more than 25 ml/m 2 . Make sure to wet surfaces completely. Used wipes must be disposed in a closed container. 5.2. Risk mitigation measures The product must only be applied for disinfection of small surfaces. Ensure adequate ventilation to prevent the formation of explosive atmospheres. Avoid contact with eyes. Apply a funnel for refilling. Keep out of reach of children and pets. Keep children and pets away from rooms where disinfection is taking place. Provide adequate ventilation before children and pets enter treated rooms. This does not apply to hospital patient rooms. 5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment First aid: In case of accident: Call a poison centre or a doctor. IF INHALED: Remove person to fresh air and keep comfortable for breathing. If on skin: Wash with water. If skin irritation occurs: Get medical advice. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell. 5.4. Instructions for safe disposal of the product and its packaging - 5.5. Conditions of storage and shelf-life of the product under normal conditions of storage Shelf-life: 36 months Keep container tightly closed. Store in a well-ventilated place. Protect from sunlight. Store at room temperature in the original container. 6. OTHER INFORMATION The product contains propan-2-ol (CAS No: 67-63-0), for which a European reference value of 129,28 mg/m 3 for the professional user was agreed and used for the risk assessment of the product. 7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 1 7.1. Trade name(s), authorisation number and specific composition of each individual product Trade name(s) Superficid® Market area: EU Desocid rapid Market area: EU Neoseptin rapid Market area: EU Novosept rapid Market area: EU Novoseptin rapid Market area: EU Lyorthol rapid Market area: EU Cosmo rapid Market area: EU Fordesin rapid Market area: EU Saltero rapid Market area: EU Prop70 rapid Market area: EU Aldovet rapid Market area: EU Vetfarm rapid Market area: EU MDI rapid Market area: EU Antiseptica rapid Market area: EU Sterisol Surface Market area: EU MENNO® I-QUICK plus Market area: EU Authorisation number EU-0030790-0001 1-1 Common name IUPAC name Function CAS number EC number Content (%) Propan-2-ol Active Substance 67-63-0 200-661-7 63,1 7.2. Trade name(s), authorisation number and specific composition of each individual product Trade name(s) Superficid® pure Market area: EU Desocid rapid pure Market area: EU Neoseptin rapid pure Market area: EU Novosept rapid pure Market area: EU Novoseptin rapid pure Market area: EU Lyorthol rapid pure Market area: EU Cosmo rapid pure Market area: EU Fordesin rapid pure Market area: EU Saltero rapid pure Market area: EU Prop70 rapid pure Market area: EU Aldovet rapid pure Market area: EU Vetfarm rapid pure Market area: EU MDI rapid pure Market area: EU Antiseptica rapid pure Market area: EU Sterisol Surface pure Market area: EU BTS 6000 Market area: EU MENNO® I-QUICK Market area: EU EWA® DES ready Market area: EU Kiehl-Rapinol Market area: EU Des A Market area: EU Authorisation number EU-0030790-0002 1-1 Common name IUPAC name Function CAS number EC number Content (%) Propan-2-ol Active Substance 67-63-0 200-661-7 63,1 META SPC 2 1. META SPC 2 ADMINISTRATIVE INFORMATION 1.1. Meta SPC 2 identifier Identifier Descorapid® 1.2. Suffix to the authorisation number Number 1-2 1.3. Product type(s) Product type(s) PT02 – Disinfectants and algaecides not intended for direct application to humans or animals (Disinfectants) PT04 – Food and feed area (Disinfectants) 2. META SPC 2 COMPOSITION 2.1. Qualitative and quantitative information on the composition of the meta SPC 2 Common name IUPAC name Function CAS number EC number Content (%) Min Max Propan-2-ol Active Substance 67-63-0 200-661-7 63,1 63,1 2.2. Type(s) of formulation of the meta SPC 2 Formulation(s) Any other liquid (AL), ready-to-use, wipes impregnated with disinfectant formulation 3. HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 2 Hazard statements Highly flammable liquid and vapour. Causes serious eye irritation. May cause drowsiness or dizziness. Repeated exposure may cause skin dryness or cracking. Precautionary statements Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. – No smoking. Keep container tightly closed. Ground and bond container and receiving equipment. Use explosion-proof electrical/ventilating/lighting equipment. Use non-sparking tools. Take action to prevent static discharges. Avoid breathing vapours. Avoid breathing spray. Use only outdoors or in a well-ventilated area. Wear eye protection. IF IN EYES:Rinse cautiously with water for several minutes.Remove contact lenses, if present and easy to do. Continue rinsing. Call a POISON CENTER or doctor if you feel unwell. If eye irritation persists:Get medical advice. If eye irritation persists:Get medical attention. In case of fire:Use alcohol-resistant foam, carbon dioxide or water mist to extinguish. Store in a well-ventilated place.Keep cool. Store locked up. Dispose of contents to/container to an approved waste disposal plant. 4. AUTHORISED USE(S) OF THE META SPC 2 4.1. Use description Table 5 Use # 1 – disinfection of surfaces – wiping Product type PT02 – Disinfectants and algaecides not intended for direct application to humans or animals (Disinfectants) Where relevant, an exact description of the authorised use - Target organism(s) (including development stage) Scientific name: Bacteria Common name: - Development stage: - Scientific name: Yeast Common name: - Development stage: - Field(s) of use Indoor Disinfection of clean non-porous surfaces such as small work surfaces in medical and non-medical areas as well as surfaces in cleanrooms (class A/B) Application method(s) Method: Wiping Detailed description: Product will be wiped directly on the surface. Application rate(s) and frequency Application Rate: Ready-to-use wipes Dilution (%): - Number and timing of application: - Category(ies) of users Industrial Professional Pack sizes and packaging material Can: 100-150 wipes Packaging: HDPE Closure material: HDPE Pack: 100-150 wipes Packaging: PET/PE 4.1.1. Use-specific instructions for use Thoroughly wipe the surface with the wipe and allow to take effect for at least 5 minutes at room temperature (20 ± 2 °C). 4.1.2. Use-specific risk mitigation measures See general directions for use. 4.1.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.1.4. Where specific to the use, the instructions for safe disposal of the product and its packaging 4.1.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 4.2. Use description Table 6 Use # 2 – disinfection of surfaces with food and feed contact – wiping Product type PT04 – Food and feed area (Disinfectants) Where relevant, an exact description of the authorised use - Target organism(s) (including development stage) Scientific name: Bacteria Common name: - Development stage: - Scientific name: Yeast Common name: - Development stage: - Scientific name: Viruses Common name: - Development stage: - Field(s) of use Indoor Disinfection of clean non-porous surfaces in kitchens and food industry including cleanrooms (class A/B) Application method(s) Method: Wiping Detailed description: Product will be wiped directly on the surface. Application rate(s) and frequency Application Rate: Ready-to-use wipes Dilution (%): - Number and timing of application: - Category(ies) of users Industrial Professional Pack sizes and packaging material Can: 100-150 wipes Packaging: HDPE Closure material: HDPE Pack: 100-150 wipes Packaging: PET/PE 4.2.1. Use-specific instructions for use Thoroughly wipe the surface with the wipe and allow to take effect for at least 5 minutes at room temperature (20 ± 2 °C). 4.2.2. Use-specific risk mitigation measures See general directions for use. 4.2.3. Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.2.4. Where specific to the use, the instructions for safe disposal of the product and its packaging 4.2.5. Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 5. GENERAL DIRECTIONS FOR USE ( 2 ) OF THE META SPC 2 5.1. Instructions for use Clean the surface carefully before use. Remove excess water from the surface before disinfection, if appropriate. Make sure to wet surfaces completely. Used wipes must be disposed in a closed container. 5.2. Risk mitigation measures The product must only be applied for disinfection of small surfaces. Ensure adequate ventilation to prevent the formation of explosive atmospheres. Avoid contact with eyes. Keep out of reach of children and pets. Keep children and pets away from rooms where disinfection is taking place. Provide adequate ventilation before children and pets enter treated rooms. This does not apply to hospital patient rooms. 5.3. Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment First aid: In case of accident: Call a poison centre or a doctor. IF INHALED: Remove person to fresh air and keep comfortable for breathing. If on skin: Wash with water. If skin irritation occurs: Get medical advice. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell. 5.4. Instructions for safe disposal of the product and its packaging - 5.5. Conditions of storage and shelf-life of the product under normal conditions of storage Shelf-life: 24 months Keep container tightly closed. Store in a well-ventilated place. Protect from sunlight. Store at room temperature in the original container. 6. OTHER INFORMATION The product contains propan-2-ol (CAS No: 67-63-0), for which a European reference value of 129,28 mg/m 3 for the professional user was agreed and used for the risk assessment of the product. 7. THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 2 7.1. Trade name(s), authorisation number and specific composition of each individual product Trade name(s) Descorapid® Tücher Market area: EU Desocid Tücher Market area: EU Neoseptin Tücher Market area: EU Novosept Tücher Market area: EU Novoseptin Tücher Market area: EU Lyorthol Tücher Market area: EU Cosmo Tücher Market area: EU Fordesin Tücher Market area: EU Saltero Tücher Market area: EU Prop70 Tücher Market area: EU Manosafe Tücher Market area: EU Dermoguard Tücher Market area: EU Dermosafe Tücher Market area: EU Aldovet Tücher Market area: EU Vetfarm Tücher Market area: EU MDI Tücher Market area: EU Antiseptica Tücher Market area: EU Antiseptica wipes Market area: EU MENNO®WIP Market area: EU Descorapid® wipes Market area: EU Desocid wipes Market area: EU Neoseptin wipes Market area: EU Novosept wipes Market area: EU Novoseptin wipes Market area: EU Lyorthol wipes Market area: EU Cosmo wipes Market area: EU Fordesin wipes Market area: EU Saltero wipes Market area: EU Prop70 wipes Market area: EU Manosafe wipes Market area: EU Dermoguard wipes Market area: EU Dermosafe wipes Market area: EU Aldovet wipes Market area: EU Vetfarm wipes Market area: EU MDI wipes Market area: EU Antiseptica wipes Market area: EU Authorisation number EU-0030790-0003 1-2 Common name IUPAC name Function CAS number EC number Content (%) Propan-2-ol Active Substance 67-63-0 200-661-7 63,1 7.2. Trade name(s), authorisation number and specific composition of each individual product Trade name(s) Superficid® pure wipes Market area: EU Desocid rapid pure wipes Market area: EU Neoseptin rapid pure wipes Market area: EU Novosept rapid pure wipes Market area: EU Novoseptin rapid pure wipes Market area: EU Lyorthol rapid pure wipes Market area: EU Cosmo rapid pure wipes Market area: EU Fordesin rapid pure wipes Market area: EU Saltero rapid pure wipes Market area: EU Prop70 rapid pure wipes Market area: EU Aldovet rapid pure wipes Market area: EU Vetfarm rapid pure wipes Market area: EU MDI rapid pure wipes Market area: EU Antiseptica rapid pure wipes Market area: EU Authorisation number EU-0030790-0004 1-2 Common name IUPAC name Function CAS number EC number Content (%) Propan-2-ol Active Substance 67-63-0 200-661-7 63,1 ( 1 ) Instructions for use, risk mitigation measures and other directions for use under this section are valid for any authorised uses within the meta SPC 1. ( 2 ) Instructions for use, risk mitigation measures and other directions for use under this section are valid for any authorised uses within the meta SPC 2.
Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.