Commission Implementing Decision (EU) 2024/1329 of 13 May 2024 amending and correcting Implementing Decision (EU) 2023/1586 as regards harmonised standards for explosion prevention and protection in explosive atmospheres, laser related equipment, safety-related parts of control systems, plastics and rubber machines, refuse collection vehicles, aircraft ground support equipment, driverless industrial trucks and their systems, electrically power assisted cycles, conveyor belts for winter sport or tourist use, pedestrian-propelled trucks, tenoning and profiling woodworking machines, tractors and machinery for agriculture and forestry, commercial vacuum packaging appliances, commercial refrigerating appliances and ice-makers, grass shears and motor-operated pedestrian controlled walk-behind garden machinery
Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗
Implementing Decision (EU) 2023/1586 is amended as follows: (1) In Article 1, the second paragraph is replaced by the following: ‘The references of the harmonised standards listed in Part Three, point 2, rows 121, 266, 324a, 343, 405, 495, 495a, 502a,513a, 671a and 681a of Annex I to this Decision are published with restriction.’; and (2) Annex I to Implementing Decision (EU) 2023/1586 is amended in accordance with Annex I to this Decision.
Annex I to Implementing Decision (EU) 2023/1586 is corrected in accordance with Annex II to this Decision.
This Decision shall enter into force on the day of its publication in the Official Journal of the European Union . Point (1)(a) of Annex I shall apply from 15 May 2027. Point (1)(b) of Annex I shall apply from 15 November 2025. Point (2)(a) of Annex I shall apply from 15 November 2025. Point (2)(b) of Annex I shall apply from 15 May 2026.
ANNEX I Annex I to Implementing Decision (EU) 2023/1586 is amended as follows: (1) in Part Two, point 2 is amended as follows: (a) row 66 is deleted; (b) rows 89 and 90 are deleted; (c) the following row is inserted: ‘66a. EN ISO 13849-1:2023 Safety of machinery – Safety-related parts of control systems – Part 1: General principles for design (ISO 13849-1:2023)’; (2) in Part Three, point 2 is amended as follows: (a) rows 103, 104, 106, 112, 125, 173, 502, 542, 550 and 551 are deleted; (b) row 495 is deleted; (c) the following rows are inserted in sequential order: ‘112a. EN 1417:2023 Plastics and rubber machines – Two-roll mills – Safety requirements’; ‘125a. EN 1501-4:2023 Refuse collection vehicles – General requirements and safety requirements – Part 4: Noise test code for refuse collection vehicles’; ‘173a. EN 1915-1:2023 Aircraft ground support equipment – General requirements – Part 1: Basic safety requirements’; ‘189a. EN ISO 3691-4:2023 Industrial trucks – Safety requirements and verification – Part 4: Driverless industrial trucks and their systems’; ‘495a. EN 15194:2017+A1:2023 Cycles – Electrically power assisted cycles – EPAC Bicycles Restriction: Harmonised standard EN 15194:2017+A1:2023 does not confer a presumption of conformity with the essential health and safety requirements set out in points 1.5.9 and 3.6.3.1 of Annex I to Directive 2006/42/EC, which require machinery to be designed and constructed to take into account the risks resulting from vibrations, and that machinery must be provided with the measurement of vibrations transmitted by the machinery to the operator of the machinery’; ‘502a. EN 15700:2023 Safety for conveyor belts for winter sport or tourist use Restriction: With regard to paragraph 7.3 of this harmonised standard, compliance with this harmonised standard does not confer a presumption of conformity to the essential health and safety requirement 1.7.4.2. (u) of Annex I to Directive 2006/42/EC’; ‘542a. EN 16307-5:2023 Industrial trucks – Safety requirements and verification – Part 5: Supplementary requirements for pedestrian-propelled trucks’; ‘585a. EN ISO 19085-12:2021 Woodworking machines – Safety – Part 12: Tenoning/profiling machines (ISO 19085-12:2021) EN ISO 19085-12:2021/A11:2023’; ‘604a. EN ISO 25119-1:2023 Tractors and machinery for agriculture and forestry – Safety-related parts of control systems – Part 1: General principles for design and development (ISO 25119-1:2018) EN ISO 25119-1:2023/A1:2023’; ‘604b. EN ISO 25119-2:2023 Tractors and machinery for agriculture and forestry – Safety-related parts of control systems – Part 2: Concept phase (ISO 25119-2:2019)’; ‘604c. EN ISO 25119-3:2023 Tractors and machinery for agriculture and forestry – Safety-related parts of control systems – Part 3: Series development, hardware and software (ISO 25119-3:2018) EN ISO 25119-3:2023/A1:2023’; ‘604d. EN ISO 25119-4:2023 Tractors and machinery for agriculture and forestry – Safety-related parts of control systems – Part 4: Production, operation, modification and supporting processes (ISO 25119-4:2018) EN ISO 25119-4:2023/A1:2023’; ‘655a. EN IEC 60335-2-119:2024 Household and similar electrical appliances – Safety – Part 2-119: Particular requirements for commercial vacuum packaging appliances EN IEC 60335-2-119:2024/A11:2024’; (d) rows 651, 698 and 699 are replaced by: ‘651. EN IEC 60335-2-89:2022 Household and similar electrical appliances – Safety – Part 2-89: Particular requirements for commercial refrigerating appliances and ice-makers with an incorporated or remote refrigerant unit or motor-compressor (IEC 60335-2-89:2019) EN IEC 60335-2-89:2022/A11:2022 EN IEC 60335-2-89:2022/AC:2023-11’; ‘698. EN IEC 62841-4-5:2021 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 4-5: Particular requirements for grass shears (IEC 62841-4-5:2021) EN IEC 62841-4-5:2021/A11:2021 EN IEC 62841-4-5:2021/AC:2024-01’; ‘699. EN IEC 62841-4-7:2022 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 4-7: Particular requirements for pedestrian controlled walk-behind lawn scarifiers and aerators (IEC 62841-4-7:2022) EN IEC 62841-4-7:2022/A11:2022 EN IEC 62841-4-7:2022/AC:2023-05 EN IEC 62841-4-7:2022/AC:2023-10’.
ANNEX II Annex I to Implementing Decision (EU) 2023/1586 is corrected as follows: (1) in Part One, point 2 is replaced by the following: ‘2. Reference of the standard. EN ISO 12100:2010, Safety of machinery – General principles for design – Risk assessment and risk reduction (ISO 12100:2010).’ (2) in Part Three, point 2, row 259 is deleted; (3) in Part Two, point 2, the following rows are inserted in sequential order: ‘26a. EN 1127-2:2014 Explosive atmospheres – Explosion prevention and protection – Part 2: Basic concepts and methodology for mining’; ‘53a. EN ISO 11554:2017 Optics and photonics – Lasers and laser-related equipment – Test methods for laser beam power, energy and temporal characteristics (ISO 11554:2017)’.
Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.