Article 1
Annex I to Implementing Decision (EU) 2023/1586 is amended in accordance with the Annex to this Decision.
Commission Implementing Decision (EU) 2026/2015 of 4 September 2026 amending and repealing Commission Implementing Decision (EU) 2023/1586 as regards harmonised standards for machinery drafted in support of Directive 2006/42/EC of the European Parliament and of the Council
Commission Implementing Decision (EU) 2026/2015 of 4 September 2026 amending and repealing Commission Implementing Decision (EU) 2023/1586 as regards harmonised standards for machinery drafted in support of Directive 2006/42/EC of the European Parliament and of the Council
Data as of 2026-09-10 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗
Article 2
Implementing Decision (EU) 2023/1586 is repealed with effect from 20 January 2027.
Article 3
This Decision shall enter into force on the day of its publication in the Official Journal of the European Union .
Supplementary provisions
ANNEXSupplementary provisions
ANNEX Annex I to Implementing Decision (EU) 2023/1586 is amended as follows: (1) in Part Two, point 2, the following rows are inserted in sequential order: ‘32a. EN ISO 3744:2026 Acoustics – Determination of sound power levels of noise sources using sound pressure – Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2025, including corrected version 2026-01)’; ‘71a. EN ISO 13855:2024 Safety of machinery – Positioning of safeguards with respect to the approach of the human body (ISO 13855:2024)’; ‘77a. EN ISO 14119:2025 Safety of machinery – Interlocking devices associated with guards – Principles for design and selection (ISO 14119:2024) EN ISO 14119/A11:2026’; ‘104a. EN IEC 62061:2021 Safety of machinery – Functional safety of safety-related control systems EN IEC 62061:2021/A1:2024’; (2) Part Three, point 2, is amended as follows: (a) the following rows are inserted in sequential order: ‘1a. EN 81-30:2025 Safety rules for the construction and installation of lifts – Lifts for the transport of goods only – Part 30: Electric and hydraulic service lifts’; ‘4b. EN 81-42:2025 Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 42: Vertical lifting appliances with enclosed carrier intended for use by persons, including persons with disability’; ‘14a. EN 415-4:2025 Safety of packaging machines – Part 4: Palletizers and depalletizers and associated equipment’; ‘102a. EN 1175:2025 Safety of industrial trucks – Electrical/electronic requirements’; ‘191a. EN ISO 3991:2025 Agricultural machinery – Robotic feed systems – Safety (ISO 3991:2025)’; ‘195a. EN ISO 4254-7:2017 Agricultural machinery – Safety – Part 7: Combine harvesters, forage harvesters, cotton harvesters and sugar cane harversters (ISO 4254-7:2017, Corrected version 2019-03) EN ISO 4254-7/A1:2026’; ‘202a. EN ISO 4254-20:2025 Agricultural machinery – Safety – Part 20: Grape, olives and coffee harvesters (ISO 4254-20:2025)’; ‘209a. EN ISO 6909:2026 Machine tools – Safety – Press brakes (ISO 6909:2026)’; ‘213a. EN ISO 8437-1:2021 Snow throwers – Safety requirements and test procedures – Part 1: Terminology and common tests (ISO 8437-1:2019/Amd 1:2026) EN ISO 8437-1:2021/A1:2026’; ‘213b. EN ISO 8437-2:2021 Snow throwers – Safety requirements and test procedures – Part 2: Pedestrian-controlled snow throwers (ISO 8437-2:2019/Amd 1:2026) EN ISO 8437-2:2021/A1:2026’; ‘213c. EN ISO 8437-3:2021 Snow throwers – Safety requirements and test procedures – Part 3: Ride-on snow throwers (ISO 8437-3:2019/Amd 1:2026) EN ISO 8437-3:2021/A1:2026’; ‘213d. EN ISO 8437-4:2021 Snow throwers – Safety requirements and test procedures – Part 4: Additional national and regional requirements (ISO 8437-4:2019/Amd 1:2026) EN ISO 8437-4:2021/A1:2026’; ‘215a. EN ISO 8528-13:2026 Reciprocating internal combustion engine driven alternating current generating sets – Part 13: Safety (ISO 8528-13:2026)’; ‘223a. EN ISO 10218-1:2025 Robotics – Safety requirements – Part 1: Industrial robots (ISO 10218-1:2025)’; ‘224a. EN ISO 10218-2:2025 Robotics – Safety requirements – Part 2: Industrial robot applications and robot cells (ISO 10218-2:2025)’; ‘261a. EN ISO 11680:2025 Machinery for forestry – Safety requirements and testing for portable pole mounted powered pruners (ISO 11680:2025)’; ‘288a. EN 12312-1:2024 Aircraft ground support equipment – Specific requirements – Part 1: Passenger stairs’; ‘348a. EN 12693:2026 Refrigerating systems and heat pumps – Safety and environmental requirements – Positive displacement refrigerant compressors’; ‘375a. EN 13001-3-5:2025 Cranes – General design – Part 3-5: Limit states and proof of competence of forged and cast hooks’; ‘406a. EN 13288:2025 Food processing machinery – Bowl lifting and tilting machines – Safety and hygiene requirements’; ‘516a. EN ISO 16089:2025 Machine tools – Safety – Stationary grinding machines (ISO 16089:2025)’; ‘545a. EN 16474:2025 Plastics and rubber machines – Tyre curing machines – Safety requirements’; ‘572 – aa. EN 17657:2025 Equipments for slaughterhouses – Slaughtering traps for bovine animals – Safety and cleaning requirements’; ‘572c. EN 17745:2025 Agricultural and forestry machinery – Environmental requirements for granule applicator of plant protection products’; ‘573b. EN 17969:2026 Earth-moving machinery – Safety – Contamination protective systems’; ‘574a. EN ISO 18497-1:2024 Agricultural machinery and tractors – Safety of partially automated, semi-autonomous and autonomous machinery – Part 1: Machine design principles and vocabulary (ISO 18497-1:2024)’; ‘574b. EN ISO 18497-2:2024 Agricultural machinery and tractors – Safety of partially automated, semi-autonomous and autonomous machinery – Part 2: Design principles for obstacle protection systems (ISO 18497-2:2024)’; ‘574c. EN ISO 18497-3:2024 Agricultural machinery and tractors – Safety of partially automated, semi-autonomous and autonomous machinery – Part 3: Autonomous operating zones (ISO 18497-3:2024)’; ‘574d. EN ISO 18497-4:2024 Agricultural machinery and tractors – Safety of partially automated, semi-autonomous and autonomous machinery – Part 4: Verification methods and validation principles (ISO 18497-4:2024)’; ‘578a. EN ISO 19085-4:2024 Woodworking machines – Safety – Part 4: Vertical panel circular sawing machines (ISO 19085-4:2024)’; ‘579a. EN ISO 19085-5:2024 Woodworking machines – Safety – Part 5: Dimension saws (ISO 19085-5:2024)’; ‘580a. EN ISO 19085-6:2024 Woodworking machines – Safety – Part 6: Single spindle vertical moulding machines (toupie) (ISO 19085-6:2024)’; ‘581a. EN ISO 19085-7:2024 Woodworking machines – Safety – Part 7: Surface planing, thickness planing and combined surface/thickness planing machines (ISO 19085-7:2024)’; ‘582a. EN ISO 19085-8:2024 Woodworking machines – Safety – Part 8: Wide belt sanding machines and surface treating machines (ISO 19085-8:2024)’; ‘583a. EN ISO 19085-9:2024 Woodworking machines – Safety – Part 9: Circular saw benches (with and without sliding table) (ISO 19085-9:2024)’; ‘585 – a. EN ISO 19085-11:2024 Woodworking machines – Safety – Part 11: Combined machines (ISO 19085-11:2024)’; ‘585b. EN ISO 19085-12:2024 Woodworking machines – Safety – Part 12: Tenoning-profiling machines (ISO 19085-12:2024)’; ‘586a. EN ISO 19085-13:2025 Woodworking machines – Safety – Part 13: Multi-blade rip sawing machines with manual loading and/or unloading (ISO 19085-13:2025)’; ‘588a. EN ISO 19085-15:2025 Woodworking machines – Safety – Part 15: Presses (ISO 19085-15:2025)’; ‘595a. EN ISO 19932-1:2025 Equipment for crop protection – Knapsack sprayers – Part 1: Safety and environmental requirements (ISO 19932-1:2025)’; ‘596a. EN ISO 19932-2:2025 Equipment for crop protection – Knapsack sprayers – Part 2: Test methods (ISO 19932-2:2025)’; ‘603a. EN ISO 23063:2025 Foundry machinery – Safety requirements for high pressure die casting machines (ISO 23063:2024)’; ‘604 – a. EN ISO 23779:2025 Shot blasting machinery – Safety and environmental requirements (ISO 23779:2024)’; ‘605a. EN ISO 28139:2021 Equipment for crop protection – Knapsack combustion engine-driven airblast sprayers – Safety and environmental requirements and test methods (ISO 28139:2019) EN ISO 28139:2021/A1:2024’; ‘621a. EN 50374:2025 Conductor cars EN 50374:2025/A1:2025’; ‘631a. EN ISO/ASTM 52938-1:2025 Additive manufacturing of metals – Environment, health and safety – Part 1: Safety requirements for PBF-LB machines (ISO/ASTM 52938-1:2025)’; ‘635a. EN IEC 60335-2-34:2023 Household and similar electrical appliances – Safety – Part 2-34: Particular requirements for motor-compressors (IEC 60335-2-34:2021) EN IEC 60335-2-34:2023/A11:2023 EN IEC 60335-2-34:2023/A12:2025’; ‘637a. EN 60335-2-38:2003 Household and similar electrical appliances – Safety – Part 2-38: Particular requirements for commercial electric griddles and griddle grills EN 60335-2-38:2003/AC:2007 EN 60335-2-38:2003/A1:2008 EN 60335-2-38:2003/A2:2024 EN 60335-2-38:2003/A11:2024’; ‘638a. EN IEC 60335-2-40:2024 Household and similar electrical appliances – Safety – Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers (IEC 60335-2-40:2022 + COR1:2024) EN IEC 60335-2-40:2024/A11:2024’; ‘644a. EN IEC 60335-2-58:2025 Household and similar electrical appliances – Safety – Part 2-58: Particular requirements for commercial electric dishwashing machines (IEC 60335-2-58:2017) EN IEC 60335-2-58:2025/A11:2025’; ‘677a. EN IEC 62841-2-6:2020 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2-6: Particular requirements for hand-held hammers (IEC 62841-2-6:2020) EN IEC 62841-2-6:2020/A11:2020 EN IEC 62841-2-6:2020/AC:2024-11 EN IEC 62841-2-6:2020/A1:2024 EN IEC 62841-2-6:2020/A12:2024’; ‘677b. EN IEC 62841-2-7:2024 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2-7: Particular requirements for hand-held spray guns (IEC 62841-2-7:2024) EN IEC 62841-2-7:2024/A11:2024 EN IEC 62841-2-7:2024/AC:2025-07’; ‘681b. EN 62841-2-11:2016 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2-11: Particular requirements for hand-held reciprocating saws (IEC 62841-2-11:2015, modified) EN 62841-2-11:2016/A1:2020 EN 62841-2-11:2016/A11:2024’; ‘681c. EN IEC 62841-2-12:2024 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2-12: Particular requirements for hand-held concrete vibrators (IEC 62841-2-12:2024) EN IEC 62841-2-12:2024/A11:2024 EN IEC 62841-2-12:2024/AC:2025-11’; ‘683a. EN IEC 62841-2-18:2026 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2-18: Particular requirements for hand-held strapping tools (IEC 62841-2-18:2024 + COR1:2025) EN IEC 62841-2-18:2026/A11:2026’; ‘683b. EN IEC 62841-2-19:2025 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2-19: Particular requirements for hand-held jointers (IEC 62841-2-19:2024) EN IEC 62841-2-19:2025/A11:2025’; ‘683c. EN IEC 62841-2-20:2025 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2-20: Particular requirements for hand-held band saws (IEC 62841-2-20:2024) EN IEC 62841-2-20:2025/A11:2025’; ‘684a. EN IEC 62841-2-22:2025 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2-22: Particular requirements for hand-held cut-off machines (IEC 62841-2-22:2025) EN IEC 62841-2-22:2025/A11:2025’; ‘684b. EN IEC 62841-2-23:2026 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 2-23: Particular requirements for hand-held die grinders and small rotary tools (IEC 62841-2-23:2024) EN IEC 62841-2-23:2026/A11:2026’; ‘694a. EN IEC 62841-3-16:2026 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 3-16: Particular requirements for transportable belt sanders, disc sanders and belt/disc sanders (IEC 62841-3-16:2025) EN IEC 62841-3-16:2026/A11:2026’; ‘697a. EN IEC 62841-4-4:2026 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 4-4: Particular requirements for lawn trimmers, lawn edge trimmers, grass trimmers, brush cutters and brush saws (IEC 62841-4-4:2020) EN IEC 62841-4-4:2026/A1:2026 EN IEC 62841-4-4:2026/A11:2026’; ‘698a. EN IEC 62841-4-6:2024 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 4-6: Particular requirements for garden blowers, garden vacuums and garden blower/vacuums (IEC 62841-4-6:2022) EN IEC 62841-4-6:2024/A11:2024 EN IEC 62841-4-6:2024/AC:2026-06’; ‘699a. EN IEC 62841-4-8:2025 Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 4-8: Particular requirements for shredders/chippers EN IEC 62841-4-8:2025/A11:2025’; (b) rows 401a and 457a are replaced by the following: ‘401a. EN 13155:2020+A1:2025 Crane – Safety – Non-fixed load lifting attachments EN 13155:2020+A1:2025/AC:2026’; ‘457a. EN 14439:2025 Cranes – Tower cranes EN 14439:2025/AC:2026’.
Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.
What to look at next
Browse all EU Legal ActsEvery instrument by type and year, full text free to read section by sectionEuropean Union legislationEU Legal Acts by type and yearGrouped by instrument type and year of enactment, so you can find others of the same kindBrowse by type and yearEuropean Union: what this database coversWhich datasets are here, which official source they come from, and how current they areEuropean Union overview