ANNEXSupplementary provisions
In the list of Annexes: - the asterisks after the titles of Annexes I to IV and the related footnote shall be deleted, - the title of Annex V shall read: 'Information document', and - at the end of the list, a new Annex VI shall be added, with the following title: 'EEC type-approval certificate'. Annex I shall be amended as follows: Item 2.1 shall be deleted. Items 2.2 and 2.3 shall be renumbered 2.1 and 2.2. Items 2.4 to 2.6 shall be deleted. Items 2.7 to 2.9 shall be renumbered 2.3 to 2.5. The following new item 2.6 shall be added after item 2.5: '2.6. Information display device. "Information display device" means a display device capable of displaying more than one type of information or message.' Items 2.10 to 2.20 shall be deleted. Item 3.1 shall be amended to read: '3.1. The application for EEC type-approval pursuant to Article 3 (4) of Directive 70/156/EEC of a vehicle type with regard to its identification of controls, tell-tales and indicators shall be submitted by the manufacturer.' Item 3.2 shall be amended to read: '3.2. A model for the information document is given in Annex V.' Item 3.2.1 shall be deleted. Item 4 shall be amended to read: '4. GRANTING OF EEC TYPE-APPROVAL 4.1. If the relevant requirements are satisfied, EEC type-approval pursuant to Article 4 (3) of Directive 70/156/EEC shall be granted. 4.2. A model for the EEC type-approval certificate is given in Annex VI. 4.3. An approval number in accordance with Annex VII to Directive 70/156/EEC shall be assigned to each type of vehicle approved. The same Member State shall not assign the same number to another type of vehicle.' Item 5.1.1: The first sentence shall read as follows: 'Where fitted, the controls, tell-tales and indicators listed in Annex II must be identified by symbols.' Item 5.1.2 shall be amended to read: '5.1.2. If symbols are used for identifying the controls, tell-tales and indicators listed in Annex III, such symbols must be in conformity with those indicated in the said Annex.' Item 5.1.3. shall be amended to read: '5.1.3 Symbols other than those shown in Annexes II and III may be used to identify controls, tell-tales and indicators, other than those listed in this Directive, provided that there is no danger of confusion with those shown in the said Annexes.' Add the following new items after item 5.1.4: '5.1.5. An information display device may be used to display messages from any source meeting the following requirements: 5.1.5.1. the brake, main-beam and direction-indicator tell-tales shall not appear in the same information display device; 5.1.5.2. the tell-tales and indicators in an information display device must provide relevant information whenever the situation that causes them to operate arises; 5.1.5.3. if two or more messages are given, they must either be repeated automatically in sequence or be indicated in such a manner as to be visible to and identifiable by the driver; 5.1.5.4. the requirements of Annex III regarding colour do not apply to tell-tales and indicators appearing in an information display device.' Item 5.2.3 shall be amended to read: '5.2.3. The symbols must stand out clearly against the background.' Item 5.2.4 shall be amended to read: '5.2.4. The colours used for tell-tales must be those prescribed in Annexes II and III.' The following new item 5.2.5 shall be added after item 5.2.4: '5.2.5. Where a control, an indicator or a tell-tale are combined, a common symbol may be used for such a combination.' Items (6) and (7) between brackets shall be amended to read: '6. AMENDMENTS TO APPROVALS 6.1. In the case of amendments to approvals granted pursuant to this Directive, the provisions of Article 5 of Directive 70/156/EEC shall apply. 7. CONFORMITY OF PRODUCTION 7.1. Measures to ensure the conformity of production shall be taken in accordance with the provisions laid down in Article 10 of Directive 70/156/EEC.' Items (8) and (9) in brackets shall be deleted. Annex II shall be amended as follows: The notes in (a) to (e) shall be deleted. The following new sentence shall be inserted below the headline: '(Symbols are in accordance with International Standard ISO 2575, fourth edition - 1982-11-15.)' The symbols appearing in Figures 1 to 29 shall be replaced by those appearing in Figures 1 to 23 as follows: 'Figure 1 Master light ISO 2575 No 4.23 Colour of tell-tale light: green Figure 2 Dipped beam headlamps ISO 2575 No 4.2 Colour of tell-tale light: green Framed areas may be solid. If the control is not separate, it is identified by the symbol shown in Figure 1. The number of lines can be four. Figure 3 Main-beam headlamps ISO 2575 No 4.1 Colour of tell-tale light: blue Framed areas may be solid. The number of lines can be four. Figure 4 Position (side) lamps ISO 2575 No 4.33 Colour of tell-tale light: green Framed areas may be solid. If the control is not separate, it is identified by the symbol shown in Figure 1. Figure 5 Front fog lamps ISO 2575 No 4.21 Colour of tell-tale light: green Framed areas may be solid. Figure 6 Rear fog lamp ISO 2575 No 4.22 Colour of tell-tale light: yellow Framed areas may be solid. Figure 7 Headlamp levelling device ISO 2575 No 4.27 Framed areas may be solid. Identification may follow Directive 76/756/EEC, Annex I, Appendix 7 The number of lines can be five. Figure 8 Parking lamps ISO 2575 No 4.9 Colour of tell-tale light: green Figure 9 Direction indicators ISO 2575 No 4.3 Colour of tell-tale light: green Framed areas may be solid. Figure 10 Hazard warning ISO 2575 No 4.4 Colour of tell-tale light: red Framed areas may be solid. Note to Figures 9 and 10: If the tell-tales for the left and right direction indicators are separate, the two arrows may also be used separately. In this case, these two separate arrows may be used simultaneously either as a hazard warning tell-tale together with, or instead of, that prescribed in Figure 10. Figure 11 Windscreen wiper ISO 2575 No 4.5 Figure 12 Windscreen washer ISO 2575 No 4.6 Figure 13 Windscreen wiper and washer ISO 2575 No 4.7 Figure 14 Headlamp cleaning device (with separate operating control) ISO 2575 No 4.19 Figure 15 Windscreen demisting and defrosting (when separate) ISO 2575 No 4.24 Colour of tell-tale light: yellow Figure 16 Rear window demisting and defrosting (when separate) ISO 2575 No 4.25 Colour of tell-tale light: yellow Figure 17 Ventilating fan (warm/cold air) ISO 2575 No 4.8 Outline only may also be used Figure 18 Diesel pre-heat ISO 2575 No 4.34 Colour of tell-tale light: yellow Figure 19 Choke (cold starting device) ISO 2575 No 4.12 Colour of tell-tale light: yellow Figure 20 Brake failure ISO 2575 No 4.31 Colour of tell-tale light: red Where a single tell-tale indicates more than one brake system condition, except brake anti-lock system failure, the symbol for brake failure in Figure 20 must be used. Figure 21 Fuel level ISO 2575 No 4.14 Colour of tell-tale light: yellow Outline only may also be used Figure 22 Battery charging condition ISO 2575 No 4.16 Colour of tell-tale light: red Figure 23 Engine coolant temperature ISO 2575 No 4.15 Colour of tell-tale light: red ' Annex III shall be amended as follows: The note shall be deleted. The following new sentence shall be inserted below the headline: '(Symbols are in accordance with International Standard ISO 2575, fourth edition 1982-11-15).' The symbols appearing in Figures 1 and 2 shall be replaced by those appearing in Figures 1 to 11 below: 'Figure 1 Parking brake ISO 2575 No 4.32 Colour of tell-tale light: red Where a single tell-tale indicates more than one brake system condition, the symbol for brake failure shown in Annex II, Figure 20, must be used. Figure 2 Rear window piper ISO 2575 No 4.28 Figure 3 Rear window washer ISO 2575 No 4.29 Figure 4 Rear window wiper and washer ISO 2575 No 4.30 Figure 5 Intermittent windscreen wiper ISO 2575 No 4.45 Figure 6 Horn ISO 2575 No 4.13 Figure 7 Front hood (bonnet) ISO 2575 No 4.10 Outline only may also be used Figure 8 Rear hood ISO 2575 No 4.11 Outline only may also be used Figure 9 Seat belt ISO 2575 No 4.18 Colour of tell-tale light: red Outline only may also be used Figure 10 Engine oil pressure ISO 2575 No 4.17 Colour of tell-tale light: red Figure 11 Unleaded petrol ISO 2575 No 4.26 ' Annex V shall be deleted and shall be replaced by the following Annex V. The subsequent new Annex VI shall be added. 'ANNEX V INFORMATION DOCUMENT No . . . (1)() pursuant to Annex I to Council Directive 70/156/EEC relating to EEC type-approval of a vehicle with respect to the interior fittings (identification of controls, tell-tales and indicators) (Directive 78/316/EEC) as last amended by Directive 93/91/EEC The following information, if applicable, must be supplied in triplicate and include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A 4 or on a folder of A 4 format. Photographs, if any, must show sufficient detail. If the systems, components or separate technical units have electronic controls, information concerning their performance must be supplied. 0. GENERAL 0.1. Make (trade name of manufacturer): 0.2. Type and general commercial description(s): 0.3. Means of identification of type, if marked on the vehicle (b): 0.3.1. Location of that marking: 0.4. Category of vehicle (c): 0.5. Name and address of manufacturer: 0.8. Address(es) of assembly plant(s): 1. GENERAL CONSTRUCTION CHARACTERISTICS OF THE VEHICLE 1.1. Photographs and/or drawings of a representative vehicle: 9. BODYWORK 9.10. Interior fittings 9.10.2. Arrangement and identification of controls, tell-tales and indicators 9.10.2.1. Photographs and/or drawings of the arrangement of symbols and controls, tell-tales and indicators: 9.10.2.2. Photographs and/or drawings of the identification of controls, tell-tales and indicators and of the vehicle parts mentioned in Directive 78/316/EEC where relevant: 9.10.2.3. Summary table: The vehicle is equipped with the following controls, indicators and tell-tales pursuant to Annexes II and III to Directive 78/316/EEC: Controls, tell-tales and indicators for which, when fitted, identification is mandatory, and symbols to be used for that purpose >(2)(2)(3)(2)(2)(3)"> ID="1">1> ID="2">Master light"> ID="1">2> ID="2">Dipped-beam headlamps"> ID="1">3> ID="2">Main-beam headlamps"> ID="1">4> ID="2">Position (side) lamps"> ID="1">5> ID="2">Front fog lamps"> ID="1">6> ID="2">Rear fog lamp"> ID="1">7> ID="2">Headlamp levelling device"> ID="1">8> ID="2">Parking lamp"> ID="1">9> ID="2">Direction indicators"> ID="1">10> ID="2">Hazard warning"> ID="1">11> ID="2">Windscreen wiper"> ID="1">12> ID="2">Windscreen washer"> ID="1">13> ID="2">Windscreen wiper and washer"> ID="1">14> ID="2">Headlamp cleaning device"> ID="1">15> ID="2">Windscreen demisting and defrosting"> ID="1">16> ID="2">Rear window demisting and defrosting"> ID="1">17> ID="2">Ventilating fan"> ID="1">18> ID="2">Diesel pre-heat"> ID="1">19> ID="2">Choke"> ID="1">20> ID="2">Brake failure"> ID="1">21> ID="2">Fuel level"> ID="1">22> ID="2">Battery charging condition"> ID="1">23> ID="2">Engine coolant temperature"" > Controls, tell-tales and indicators for which, when fitted, identification is optional, and symbols which must be used if they are to be identified >(4)(4)(5)(4)(4)(5)"> ID="1">1> ID="2">Parking brake"> ID="1">2> ID="2">Rear window wiper"> ID="1">3> ID="2">Rear window washer"> ID="1">4> ID="2">Rear window wiper and washer"> ID="1">5> ID="2">Intermittent windscreen wiper"> ID="1">6> ID="2">Audible warning device (horn)"> ID="1">7> ID="2">Front hood (bonnet)"> ID="1">8> ID="2">Rear hood (boot)"> ID="1">9> ID="2">Seat belt"> ID="1">10> ID="2">Engine oil pressure"> ID="1">11> ID="2">Unleaded petrol"" > ANNEX VI MODEL (maximum format: A 4 (210 × 297 mm)) EEC TYPE-APPROVAL CERTIFICATE Stamp of Administration Communication concerning the - type-approval (6) - extension of type-approval (6) - refusal of type-approval (6) - withdrawal of type-approval (6) of a type of vehicle/component/separate technical unit (6) with regard to Directive 78/316/EEC, as last amended by Directive 93/91/EEC. Type-approval number: Reason for extension: SECTION I 0.1. Make (trade name of manufacturer): 0.2. Type and general commercial description(s): 0.3. Means of identification of type if marked on the vehicle/component/separate technical unit (6) (7): 0.3.1. Location of that marking: 0.4. Category of vehicle (8): 0.5. Name and address of manufacturer: 0.7. In the case of components and separate technical units, location and method of affixing of the EEC type-approval mark: 0.8. Name(s) and address(es) of assembly plant(s): SECTION II 1. Additional information (where applicable): see Appendix 2. Technical service responsible for carrying out the tests: 3. Date of test report: 4. Number of test report: 5. Remarks (if any): see Appendix 6. Place: 7. Date: 8. Signature: 9. The index to the information package lodged with the approval authority, which may be obtained on request, is attached. Appendix to EEC type-approval certificate No . . . concerning the type-approval of a vehicle with regard to Directive 78/316/EEC as last amended by Directive 93/91/EEC 1. Additional information Not applicable 5. Remarks: (e.g. valid for both left-hand drive and right-hand drive vehicles)' (1)() The item numbers and footnotes used in this Information Document correspond to those set out in Annex I to Directive 70/156/EEC, as last amended by Directive 92/53/EEC. Items not relevant for the purpose of this Directive are omitted. (2) × = yes. - = no or not separately available. o = optional. (3) d = directly on control, indicator or tell-tale. c = in close vicinity. (4) × = yes. - = no or not separately available. o = optional. (5) d = directly on control, indicator or tell-tale. c = in close vicinity. (6) Delete where not applicable. (7) If the means of identification of the type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information document/type-approval certificate such characters shall be represented in the documentation by the symbol '?' (e.g. ABC??123??). (8) As defined in Annex II A to Directive 70/156/EEC.