ANNEX ISupplementary provisions
Flat and curved glass panels (including basic glass, processed glass, special or safety glass, coated, filmed, enamelled, surface-treated or mirrored glass): For all uses other than: - for use in a glazed assembly intended specifically to provide fire resistance, - for use as anti-bullet or anti-explosion glazing. Channel-shaped glass (wired or unwired): For all uses other than: - for use in a glazed assembly intended specifically to provide fire resistance. Insulating glass units: For all uses other than: - for use in a glazed assembly intended specifically to provide fire resistance, - for use as anti-bullet or anti-explosion glazing. Glass blocks: For use in non-load bearing applications other than: - for anti-bullet and anti-explosion uses. Glass-block wall panels: For all non-load bearing uses other than: - for fire compartmentation uses, - for anti-bullet and anti-explosion uses. ANNEX II Flat and curved glass panels (including basic glass, processed glass, special or safety glass, coated, filmed, enamelled, surface-treated or mirrored glass): - for anti-bullet and anti-explosion uses, - for use in a glazed assembly intended specifically to provide fire resistance. Channel-shaped glass (wired or unwired): - for use in a glazed assembly intended specifically to provide fire resistance. Insulating glass units: - for anti-bullet and anti-explosion uses, - for use in a glazed assembly intended specifically to provide fire resistance. Glass blocks: for anti-bullet and anti-explosion uses. Glass-block wall panels: - for fire compartmentation uses, - for anti-bullet and anti-explosion uses. ANNEX III Note: for products having more than one of the intended uses specified in the following families, the tasks for the approved body, derived from the relevant systems of attestation of conformity, are cumulative. PRODUCT FAMILY FLAT GLASS, PROFILED GLASS AND GLASS-BLOCK PRODUCTS (1/6) 1. Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY FLAT GLASS, PROFILED GLASS AND GLASS-BLOCK PRODUCTS (2/6) 1. Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY FLAT GLASS, PROFILED GLASS AND GLASS-BLOCK PRODUCTS (3/6) 1. Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY FLAT GLASS, PROFILED GLASS AND GLASS-BLOCK PRODUCTS (4/6) 1. Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY FLAT GLASS, PROFILED GLASS AND GLASS-BLOCK PRODUCTS (5/6) 1. Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY FLAT GLASS, PROFILED GLASS AND GLASS-BLOCK PRODUCTS (6/6) 1. Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.