ANNEX ISupplementary provisions
Internal covering system of gypsum fibre boards (EOTA ref. 05.04/01): For uses except those subject to reaction to fire regulations for products made of materials falling into classes A1(1), A2(2), B(3), C(4). Prefabricated cavity trays (EOTA ref. 06.04/05) (1) Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material). (2) Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material). (3) Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material). (4) Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material). ANNEX II Internal covering system of gypsum fibre boards (EOTA ref. 05.04/01): For uses subject to reaction to fire regulations for products made of materials falling into classes A1(1), A2(2), B(3), C(4). Couplings and sleeves for standardised reinforcing bars (EOTA ref. 03.01/02) Corrugated steel reinforcement sheets (for composite structural floor systems) (EOTA ref. 05.02/02) Pile joint (connection device for load-bearing pre-cast concrete piles) (EOTA ref. 01.03/09) Rock shoe (anchoring device for load-bearing pre-cast concrete piles) (EOTA ref. 01.03/09) (1) Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material). (2) Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material). (3) Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material). (4) Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material). ANNEX III ATTESTATION OF CONFORMITY Note: for products/kits having more than one of the intended uses specified in the following tables, the tasks for the approved body, derived from the relevant systems of attestation of conformity, are cumulative. SIX PRODUCTS FOR EUROPEAN TECHNICAL APPROVALS (TABLE 1/3) Systems of attestation of conformity For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant European technical approval: >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases, the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. SIX PRODUCTS FOR EUROPEAN TECHNICAL APPROVALS (TABLE 2/3) Systems of attestation of conformity For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant European technical approval: >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases, the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. SIX PRODUCTS FOR EUROPEAN TECHNICAL APPROVALS (TABLE 3/3) Systems of attestation of conformity For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant European technical approval: >TABLE> The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such a characteristic (see Article 2.1 of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases, the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.