ADMINISTRATIVE DOCUMENTS FOR EC TYPE-APPROVAL
ANNEX ISupplementary provisions
ANNEX I ADMINISTRATIVE DOCUMENTS FOR EC TYPE-APPROVAL PART 1 MODEL Information document No … relating to EC component type-approval of an air-conditioning system or of a component thereof The following information, if applicable, must be supplied in triplicate and include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, must show sufficient detail. If the components have electronic controls, information concerning their performance must be supplied. 0 GENERAL 0.1 Make (trade name of manufacturer): … 0.2 Type: … 0.2.1 Commercial name(s), if available: … 0.2.2 Component material: … 0.2.3 Drawing or scheme of a component: … 0.2.4 Reference or part number of the component: … 0.5 Name and address of manufacturer: … 0.7 Location and method of affixing of the EC type-approval mark: … 0.8 Address(es) of assembly plant(s): … 9. BODYWORK 9.10.8. Leakage in g/year of the leak component/air-conditioning system (if tested by the manufacturer) ( 1 ) : PART 2 MODEL EC TYPE-APPROVAL CERTIFICATE (maximum format: A4 (210 × 297 mm)) STAMP OF ADMINISTRATION Communication concerning the — type-approval — extension of type-approval ( 2 ) — refusal of type-approval ( 2 ) — withdrawal of type-approval ( 2 ) of a type of vehicle/component/separate technical unit ( 2 ) with regard to Directive 2006/40/EC, as implemented by Regulation (EC) No 706/2007 ( 2 ) . Type-approval number … Reason for extension … SECTION I 0.1 Make (trade name of manufacturer): … 0.2 Type: … 0.2.1 Commercial name(s), if available: … 0.3 Means of identification of type, if marked on the vehicle/component/separate technical unit ( 2 ) … 0.5 Name and address of manufacturer: … 0.7 In the case of components and separate technical units, location and method of affixing of the EC type-approval mark: … 0.8 Address(es) of assembly plant(s): … SECTION II 1 Additional information (where applicable): (see Addendum) 2 Technical service responsible for carrying out the tests: … 3 Date of test report: … 4 Number of test report: … 5 Remarks (if any): (see Addendum) 6 Place: … 7 Date: … 8 Signature: … 9 The index to the information package lodged with the approval authority, which may be obtained on request, is attached. Addendum to EC type-approval certificate No … concerning the type-approval of an air-conditioning system or leak component with regard to Directive 2006/40/EC 1 Additional information 1.1 Brief description of the system or leak component: … 1.2 Leakage in g/year ( 2 ) : … 1.3 Remarks: (e.g., valid for left-hand drive and right-hand drive vehicles): … PART 3 EC COMPONENT TYPE-APPROVAL MARK 1. GENERAL 1.1. The EC component type-approval mark consists of: 1.1.1. a rectangle surrounding the lower case letter ‘e’ followed by the distinguishing number or letters of the Member State which has granted the EC component type-approval: 1 for Germany 2 for France 3 for Italy 4 for the Netherlands 5 for Sweden 6 for Belgium 7 for Hungary 8 for the Czech Republic 9 for Spain 11 for the United Kingdom 12 for Austria 13 for Luxembourg 17 for Finland 18 for Denmark 19 for Romania 20 for Poland 21 for Portugal 23 for Greece 24 for Ireland 26 for Slovenia 27 for Slovakia 29 for Estonia 32 for Latvia 34 for Bulgaria 36 for Lithuania 49 for Cyprus 50 for Malta, 1.1.2. in the vicinity of the rectangle the ‘base approval number’ contained in Section 4 of the type-approval number referred to in Annex VII of Directive 70/156/EEC, preceded by the two figures indicating the sequence number assigned to the most recent major technical amendment to Directive 2006/40/EC or this Regulation on the date the EC component type-approval was granted. For this Regulation, the sequence number is 00. 1.2. The EC component type-approval mark must be clearly legible and indelible. 2. EXAMPLE OF THE EC COMPONENT TYPE-APPROVAL MARK PART 4 MODEL Information document No … relating to EC type-approval of a vehicle with regard to emissions from air-conditioning system The following information, if applicable, must be supplied in triplicate and include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, must show sufficient detail. If the components have electronic controls, information concerning their performance must be supplied. 0 GENERAL 0.1 Make (trade name of manufacturer): … 0.2 Type: … 0.2.1 Commercial name(s), if available: … 0.3 Means of identification of type, if marked on the vehicle/component/separate technical unit ( 3 ) … 0.3.1 Location of that marking: … 0.4 Category of vehicle: … 0.5 Name and address of manufacturer: … 0.7 In the case of components and separate technical units, location and method of affixing of the EC type-approval mark … 0.8 Address(es) of assembly plant(s) … 9. BODYWORK 9.10.8 The air-conditioning system is designed to contain fluorinated greenhouse gases with a global warming potential higher than 150: YES/NO ( 3 ) Gas used as refrigerant: … If YES, fill in the following sections 9.10.8.1 Drawing and brief description of the air-conditioning system, including the reference or part number and material of the leak components: … 9.10.8.2 Leakage in g/year of the air-conditioning system: … 9.10.8.2.1. In case of leak component testing: list of leak components including the corresponding reference or part number and material, with their respective yearly leakages and information about the test (e.g. test report no., approval No, etc.): … 9.10.8.2.2. In case of system testing: reference or part number and material of the components of the system and information about the test (e.g. test report No, approval no., etc.): … PART 5 MODEL EC TYPE-APPROVAL CERTIFICATE (maximum format: A4 (210 × 297 mm)) STAMP OF ADMINISTRATION Communication concerning the — type-approval — extension of type-approval ( 4 ) — refusal of type-approval ( 4 ) — withdrawal of type-approval ( 4 ) of a type of vehicle/component/separate technical unit ( 4 ) with regard to Directive 2006/40/EC, as implemented by Regulation (EC) No 706/2007. Type-approval Number: … Reason for extension: … SECTION I 0.1 Make (trade name of manufacturer): … 0.2 Type: … 0.2.1 Commercial name(s), if available: … 0.3 Means of identification of type, if marked on the vehicle/component/separate technical unit ( 4 ) … 0.3.1 Location of that marking: … 0.4 Category of vehicle: … 0.5 Name and address of manufacturer: … 0.7 In the case of components and separate technical units, location and method of affixing of the EC type-approval mark: … 0.8 Address(es) of assembly plant(s): … SECTION II 1 Additional information (where applicable): (see Addendum) 2 Technical service responsible for carrying out the tests: … 3 Date of test report: … 4 Number of test report: … 5 Remarks (if any): (see Addendum) 6 Place: … 7 Date: … 8 Signature: … 9 The index to the information package lodged with the approval authority, which may be obtained on request, is attached. Addendum to EC type-approval certificate No … concerning the type-approval of a vehicle with regard to Directive 2006/40/EC 1 Additional information 1.1 Brief description of the vehicle type as regards its air-conditioning system: … 1.2 The air-conditioning system using a fluorinated greenhouse gas with a global warming potential higher than 150: YES/NO Gas used as refrigerant: If YES, fill in the following sections 1.3 Overall leakage in g/year: … 1.4 Remarks: (e.g., valid for left-hand drive and right-hand drive vehicles): … ( 1 ) Delete where appropriate. Fill in only if the component/system is designed for use of a fluorinated greenhouse gas with a global warming potential higher than 150. ( 2 ) Delete where appropriate. ( 2 ) Fill in only if the system is designed for use of a fluorinated greenhouse gas with a global warming potential higher than 150. ( 3 ) Delete where appropriate. ( 4 ) Delete where appropriate.