Addendum
ANNEX IISupplementary provisions
ANNEX II Administrative documents for EC type-approval of 112-based eCall in-vehicle STU or 112-based eCall in-vehicle system component PART 1 Information document MODEL Information document No … relating to the EC type-approval of a 112-based eCall in-vehicle STU or 112-based eCall in-vehicle system component ( 3 ). The following information shall be supplied in triplicate and include a list of contents. Any drawings shall be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, shall show sufficient detail. If the separate technical unit or component referred to in this information document have electronic controls, information concerning their performance shall be supplied. 0. GENERAL 0.1. Make (trade name of manufacturer): … 0.2. Type: … 0.3. Means of identification of type, if marked on the Separate Technical Unit ( 1 ): … 0.3.1. Location of that marking: … 0.4. In case of STU, intended for category of vehicle ( 2 ): … 0.5. Company name and address of manufacturer: … 0.7. Location and method of affixing of the EC approval mark: … 0.9. Name and address of the manufacturer's representative (if any): … 12.8. eCall system 12.8.2. Technical description and/or schematic drawings: … 12.8.3.1. Photographs and/or drawings in sufficient detail and to an appropriate scale to enable the STU or component to be identified. The drawings must show the intended position of the STU or component on the vehicle and the space intended for the EC type-approval mark of the STU or component: … 12.8.3.1.1. Instructions for installation in the vehicle, including the position and orientation of the 112-based eCall in-vehicle system component: … 12.8.3.1.2. Location and method of mounting the 112-based eCall in-vehicle STU in the vehicle: … 12.8.3.2. List of the main constituent parts of the STU or component: … 12.8.7. Declaration of conformity with the standards referred to in Article 5(8) of Regulation (EU) 2015/758: yes/no ( 3 ). Explanatory notes ( 1 ) If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information document, such characters shall be represented in the documentation by the symbol ‘?’ (e.g. ABC??123??). ( 2 ) As defined in Section A of Annex II to Directive 2007/46/EC. ( 3 ) Delete where not applicable. PART 2 EC type-approval certificate MODEL Format A4 (210 × 297 mm) EC TYPE-APPROVAL CERTIFICATE Stamp of type-approval authority Communication concerning: — EC type-approval ( 1 ) — extension of EC type-approval ( 1 ) — refusal of EC type-approval ( 1 ) — withdrawal of EC type-approval ( 1 ) of 112-based eCall in-vehicle STU/ 112-based eCall in-vehicle system component ( 1 ) with regard to Regulation (EU) 2015/758. EC type-approval number: … Reason for extension: … SECTION I 0.1. Make (trade name of manufacturer): … 0.2. Type: … 0.3. Means of identification of type if marked on the separate technical unit/component ( 2 ) : … 0.3.1. Location of that marking: … 0.4. In case of separate technical unit, intended for category of vehicle ( 3 ): … 0.5. Name and address of manufacturer: … 0.7. Location and method of affixing of the EC approval mark: … 0.9. Name and address of the manufacturer's representative (if any): … SECTION II 1. Additional information (where applicable): see Addendum 2. Technical service responsible for carrying out the tests: … 3. Date of test report: … 4. Number of test report: … 5. Remarks (if any): see Addendum. 6. Place: … 7. Date: … 8. Signature: … Attachments: 1. Information package. 2. Test report. Addendum to EC type-approval certificate No … 1. Additional information 1.1. Brief description of the 112-based eCall in-vehicle STU/112-based eCall in-vehicle system component ( 3 ) : … 1.1.1. Instructions for installation in the vehicle, including the position and orientation of the 112-based eCall in-vehicle system component: … 1.1.2. Example of the EC type-approval marking on the 112-based eCall in-vehicle STU/112-based eCall in-vehicle system component ( 3 ) : … 1.2. Location and method of mounting of the eCall separate technical unit in the vehicle: … 1.3. Means of triggering: … 1.4. Power supply: … 2. The 112-based eCall in-vehicle system component complies with the technical requirements set out in Annex I to Commission Delegated Regulation (EU) 2017/79. In addition, it also complies with the technical requirements covered by: 2.1. Annex IV to Delegated Regulation (EU) 2017/79: yes/no ( 3 ) . 2.2. Annex VI to Delegated Regulation (EU) 2017/79: yes/no ( 3 ) . 2.3. Annex VII to Delegated Regulation (EU) 2017/79: yes/no ( 3 ) . 3. Remarks (if any): … PART 3 EC type-approval mark for STUs and components 1. The EC component and separate technical unit type-approval mark shall consist of: 1.1. A rectangle surrounding the lower-case letter ‘e’ followed by the distinguishing number of the Member State which has granted the EC component or separate technical unit type-approval: 1 for Germany 12 for Austria 26 for Slovenia 2 for France 13 for Luxembourg 27 for Slovakia 3 for Italy 17 for Finland 29 for Estonia 4 for the Netherlands 18 for Denmark 32 for Latvia 5 for Sweden 19 for Romania 34 For Bulgaria 6 for Belgium 20 for Poland 36 For Lithuania 7 for Hungary 21 for Portugal 49 For Cyprus 8 for the Czech Republic 23 for Greece 50 For Malta 9 for Spain 24 for Ireland 11 for the United Kingdom 25 for Croatia 1.2. In the vicinity of the rectangle the ‘base approval number’ contained in Section 4 of the type-approval number preceded by the two figures indicating the sequence number assigned to this Regulation. The sequence number is ‘00’ at present. 1.3. In case of a 112-based eCall in-vehicle STU, in the vicinity of the rectangle the sequence number shall be preceded by the symbol ‘ECALL’. 2. The EC type-approval mark is affixed to a main part of the 112-based eCall in-vehicle STU or 112-based eCall in-vehicle system component in such a way as to be indelible as well as clearly and easily legible. 3. Example of EC type-approval marks for 112-based eCall in-vehicle STUs and 112-based eCall in-vehicle system components is shown respectively in Figure 1 and Figure 2. Figure 1 Example of EC type-approval mark for 112-based eCall in-vehicle STUs Explanatory note Legend The EC separate technical unit type-approval was issued by Bulgaria under number 0046. The first two digits ‘00’ indicate that the separate technical unit was approved according to this Regulation. Figure 2 Example of EC type-approval mark for 112-based eCall in-vehicle system components Explanatory note Legend The EC component type-approval was issued by Germany under number 00026. The first two digits ‘00’ indicate that the component was approved according to this Regulation. ( 1 ) Delete where not applicable. ( 2 ) If the means of identification of type contains characters not relevant to describe the vehicle, component or separate technical unit types covered by this information document, such characters shall be represented in the documentation by the symbol ‘?’ (e.g. ABC??123??). ( 3 ) Delete where not applicable.