ANNEX IVSupplementary provisions
ANNEX IV Annex IV is amended as follows: (1) in point 147.A.145, point (a) is replaced by the following: ‘(a) The maintenance training organisation may carry out the following as permitted by and in accordance with the maintenance training organisation exposition: (i) basic training courses to the Annex III (Part-66) syllabus, or part thereof; (ii) aircraft type/task training courses in accordance with Annex III (Part-66); (iii) the examination of students who attended the basic or aircraft type training course at the maintenance training organisation; (iv) the examination of students who did not attend the aircraft type training course at the maintenance training organisation; (v) the examination of students who did not attend the basic training course at the maintenance training organisation, provided that: (1) the examination is conducted at one of the locations identified in the approval certificate, or (2) if performed at locations not identified in the approval certificate, as permitted by points (b) and (c), either — the examination is provided through a European Central Question Bank (ECQB), or — in the absence of an ECQB, the competent authority selects the questions for the examination; (vi) the issue of certificates in accordance with Appendix III following successful completion of the approved basic or aircraft type training courses and examinations specified in points (a)(i), (a)(ii), (a)(iii), (a)(iv) and (a)(v), as applicable.’; (2) Appendixes I and II are replaced by the following: ‘Appendix I Basic training course duration The minimum duration of a complete basic training course shall be as follows: Basic Course Duration (in hours) Theoretical Training Ratio (in %) A1 800 30–35 A2 650 30–35 A3 800 30–35 A4 800 30–35 B1.1 2 400 50–60 B1.2 2 000 50–60 B1.3 2 400 50–60 B1.4 2 400 50–60 B2 2 400 50–60 B2L 1 500 ( *1 ) 50–60 B3 1 000 50–60 Appendix II Maintenance Training Organisation Approval referred to in Annex IV (Part-147) — EASA Form 11 Text of image Page 1 of 2 [MEMBER STATE (*)] A Member of the European Union (**) MAINTENANCE TRAINING AND EXAMINATION ORGANISATION APPROVAL CERTIFICATE Reference: [MEMBER STATE CODE (*)].147.[XXXX] Pursuant to Regulation (EC) No 216/2008 of the European Parliament and of the Council and to Commission Regulation (EU) No 1321/2014, for the time being in force and subject to the conditions specified below, the [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] hereby certifies: [COMPANY NAME AND ADDRESS] as a maintenance training organisation in compliance with Section A of Annex IV (Part-147) of Regulation (EU) No 1321/2014, approved to provide training and conduct examinations listed in the approval schedule attached and to issue related certificates of recognition to students using the above references. CONDITIONS: 1. This approval is limited to what is specified in the scope of work section of the approved maintenance training organisation exposition as referred to in Section A of Annex IV (Part-147); and 2. this approval requires compliance with the procedures specified in the approved maintenance training organisation exposition; and 3. this approval is valid whilst the approved maintenance training organisation remains in compliance with Annex IV (Part-147) of Regulation (EU) No 1321/2014; and 4. subject to compliance with the foregoing conditions, this approval shall remain valid for an unlimited duration unless the approval has previously been surrendered, superseded, suspended or revoked. Date of original issue: Date of this revision: Revision No: Signed: For the competent authority: [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] EASA Form 11 Issue 5 (*) or EASA if EASA is the competent authority (**) Delete for non-EU Member States or EASA. Text of image Page 2 of 2 MAINTENANCE TRAINING AND EXAMINATION ORGANISATION APPROVAL SCHEDULE Reference: [MEMBER STATE CODE (*)].147.[XXXX] Organisation: [COMPANY NAME AND ADDRESS] This approval schedule is limited to those trainings and examinations specified in the scope of work section of the approved maintenance training organisation exposition. Maintenance training organisation exposition reference: Date of original issue: Date of last revision approved: Revision No: Signed: For the competent authority: [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] EASA Form 11 Issue 5 CLASS LICENCE CATEGORY LIMITATION BASIC (**) B1 (**) TB1.1 (**) AEROPLANES TURBINE (**) TB1.2 (**) AEROPLANES PISTON (**) TB1.3 (**) HELICOPTERS TURBINE (**) TB1.4 (**) HELICOPTERS PISTON (**) B2 (**)/(****) TB2 (**) AVIONICS (**) B2L (**) TB2L (**) AVIONICS (indicate system ratings) (**) B3 (**) TB3 (**) PISTON ENGINE NON-PRESSURISED AERO-PLANES OF 2 000 KG MTOM AND BELOW (**) A (**) TA.1 (**) AEROPLANES TURBINE (**) TA.2 (**) AEROPLANES PISTON (**) TA.3 (**) HELICOPTERS TURBINE (**) TA.4 (**) HELICOPTERS PISTON (**) L (**) (Only examination) TL (**) QUOTE THE SPECIFIC LICENCE SUB-CATEGORY (**) TYPEITASK (**) C (**) T4 (**) [QUOTE AIRCRAFT TYPE] (***) B1 (**) T1 (**) [QUOTE AIRCRAFT TYPE] (***) B2 (**) T2 (**) [QUOTE AIRCRAFT TYPE] (***) A (**) T3 (**) [QUOTE AIRCRAFT TYPE] (***) (*) or EASA if EASA is the competent authority. (**) Delete as appropriate if the organisation is not approved. (***) Complete with the appropriate rating and limitation. (****) The approval for the Basic B2 course/examination includes approval for B2L course/examination for all system ratings. ’; (3) the EASA Form 149 Issue 2 contained in Appendix III is replaced by the following: Text of image Page 1 of 2 [MEMBER STATE (*)] A Member of the European Union (**) MAINTENANCE TRAINING AND EXAMINATION ORGANISATION APPROVAL CERTIFICATE Reference: [MEMBER STATE CODE (*)].147.[XXXX] Pursuant to Regulation (EC) No 216/2008 of the European Parliament and of the Council and to Commission Regulation (EU) No 1321/2014, for the time being in force and subject to the conditions specified below, the [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] hereby certifies: [COMPANY NAME AND ADDRESS] as a maintenance training organisation in compliance with Section A of Annex IV (Part-147) of Regulation (EU) No 1321/2014, approved to provide training and conduct examinations listed in the approval schedule attached and to issue related certificates of recognition to students using the above references. CONDITIONS: 1. This approval is limited to what is specified in the scope of work section of the approved maintenance training organisation exposition as referred to in Section A of Annex IV (Part-147); and 2. this approval requires compliance with the procedures specified in the approved maintenance training organisation exposition; and 3. this approval is valid whilst the approved maintenance training organisation remains in compliance with Annex IV (Part-147) of Regulation (EU) No 1321/2014; and 4. subject to compliance with the foregoing conditions, this approval shall remain valid for an unlimited duration unless the approval has previously been surrendered, superseded, suspended or revoked. Date of original issue: Date of this revision: Revision No: Signed: For the competent authority: [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] EASA Form 11 Issue 5 (*) or EASA if EASA is the competent authority (**) Delete for non-EU Member States or EASA. ( *1 ) This number of hours shall be increased as follows, depending on the additional system ratings selected: System Rating Duration (in hours) Theoretical Training Ratio (in %) COM/NAV 90 50–60 INSTRUMENTS 55 AUTOFLIGHT 80 SURVEILLANCE 40 AIRFRAME SYSTEMS 100