ANNEX IVSupplementary provisions
ANNEX IV Annex IV to Regulation (EU) No 1321/2014 is amended as follows: (1) in point 147.B.25, point (b) is replaced by the following: ‘(b) All exemptions granted in accordance with Article 71(1) of Regulation (EU) 2018/1139 shall be recorded and retained by the competent authority.’ (2) Appendix II is replaced by the following: ‘Appendix II Maintenance Training Organisation Approval — EASA Form 11 Text of image Page 1 of 2 [MEMBER STATE (*)] A Member of the European Union (**) MAINTENANCE TRAINING AND EXAMINATION ORGANISATION APPROVAL CERTIFICATE Reference: [MEMBER STATE CODE (*)].147.[XXXX] Pursuant to Regulation (EU) 2018/1139 of the European Parliament and of the Council and to Commission Regulation (EU) No 1321/2014, for the time being in force and subject to the condition specified below, the [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] hereby certifies: [COMPANY NAME AND ADDRESS] as a maintenance training organisation in compliance with Section A of Annex IV (Part-147) of Regulation (EU) No 1321/2014, approved to provide training and conduct examinations listed in the approval schedule attached and to issue related certificates of recognition to students using the above references. CONDITIONS: 1. This approval is limited to what is specified in the scope of work section of the approved maintenance training organisation exposition as referred to in Section A of Annex IV (Part-147); and 2. this approval requires compliance with the procedures specified in the approved maintenance training organisation exposition; and 3. this approval is valid whilst the approved maintenance training organisation remains in compliance with Annex IV (Part-147) of Regulation (EU) No 1321/2014; and 4. subject to compliance with the foregoing conditions, this approval shall remain valid for an unlimited duration unless the approval has previously been surrendered, superseded, suspended or revoked. Date of original issue: Date of this revision: Revision No: Signed: For the competent authority: [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] EASA Form 11 Issue 6 (*) Or EASA if EASA is the competent authority. (**) Delete for non-EU Member States or EASA. Text of image Page 2 of 2 MAINTENANCE TRAINING AND EXAMINATION ORGANISATION APPROVAL SCHEDULE Reference: [MEMBER STATE CODE (*)].147.[XXXX] Organisation: [COMPANY NAME AND ADDRESS] This approval schedule is limited to those trainings and examinations specified in the scope of work section of the approved maintenance training organisation exposition. Maintenance training organisation exposition reference: Date of original issue: Date of last revision approved: Revision No: Signed: For the competent authority:[COMPETENT AUTHORITY OF THE MEMBER STATE (*)] EASA Form 11 Issue 5 (*) Or EASA if EASA is the competent authority. (**) Delete as appropriate if the organisation is not approved. (***) Complete with the appropriate rating and limitation. (****) The approval for the Basic B2 course/examination includes approval for B2L course/examination for all system ratings. CLASS LICENCE CATEGORY LIMITATION BASIC (**) B1 (**) TB1.1 (**) AEROPLANES TURBINE (**) TB1.2 (**) AEROPLANES PISTON (**) TB1.3 (**) HELICOPTERS TURBINE (**) TB1.4 (**) HELICOPTERS PISTON (**) B2 (**)/(****) TB2 (**) AVIONICS (**) B2L (**) TB2L (**) AVIONICS (indicate system rating) (**) B3 (**) TB3 (**) PISTON-ENGINE NON-PRESSURISED AEROPLANES 2 000 KG MTOM AND BELOW (**) A (**) TA.1 (**) AEROPLANES TURBINE (**) TA.2 (**) AEROPLANES PISTON (**) TA.3 (**) HELICOPTERS TURBINE (**) TA.4 (**) HELICOPTERS PISTON (**) L (**) (Only examination) TL (**) QUOTE THE SPECIFIC LICENCE SUB-CATEGORY (**) TYPE/TASK (**) C (**) T4 (**) [QUOTE AIRCRAFT TYPE] (***) B1 (**) T1 (**) [QUOTE AIRCRAFT TYPE] (***) B2 (**) T2 (**) [QUOTE AIRCRAFT TYPE] (***) A (**) T3 (**) [QUOTE AIRCRAFT TYPE] (***) ’ (3) Appendix III is replaced by: ‘1. Basic Training and Examination The basic training certificate template shall be used for recognition of completion of either the basic training or the basic examination, or both the basic training and basic training examinations. The training certificate shall clearly identify each individual module examination by date passed together with the corresponding version of Appendix I to Annex III (Part-66). Text of image Page 1 of 2 [MEMBER STATE (*)] A Member of the European Union (**) MAINTENANCE TRAINING AND EXAMINATION ORGANISATION APPROVAL CERTIFICATE Reference: [MEMBER STATE CODE (*)].147.[XXXX] Pursuant to Regulation (EU) 2018/1139 of the European Parliament and of the Council and to Commission Regulation (EU) No 1321/2014, for the time being in force and subject to the condition specified below, the [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] hereby certifies: [COMPANY NAME AND ADDRESS] as a maintenance training organisation in compliance with Section A of Annex IV (Part-147) of Regulation (EU) No 1321/2014, approved to provide training and conduct examinations listed in the approval schedule attached and to issue related certificates of recognition to students using the above references. CONDITIONS: 1. This approval is limited to what is specified in the scope of work section of the approved maintenance training organisation exposition as referred to in Section A of Annex IV (Part-147); and 2. this approval requires compliance with the procedures specified in the approved maintenance training organisation exposition; and 3. this approval is valid whilst the approved maintenance training organisation remains in compliance with Annex IV (Part-147) of Regulation (EU) No 1321/2014; and 4. subject to compliance with the foregoing conditions, this approval shall remain valid for an unlimited duration unless the approval has previously been surrendered, superseded, suspended or revoked. Date of original issue: Date of this revision: Revision No: Signed: For the competent authority: [COMPETENT AUTHORITY OF THE MEMBER STATE (*)] EASA Form 11 Issue 6 (*) Or EASA if EASA is the competent authority. (**) Delete for non-EU Member States or EASA. 2. Type Training and Examination The type training certificate template shall be used for recognition of completion of either the theoretical elements or the practical elements, or both the theoretical and practical elements of the type rating training course. The certificate shall indicate the airframe/engine combination for which the training was imparted. The appropriate references shall be deleted as applicable and the course type box shall detail whether only the theoretical elements or the practical elements were covered or whether theoretical and practical elements were covered. The training certificate shall clearly identify if the course is a complete course or a partial course (such as an airframe or powerplant or avionic/electrical course) or a difference course based upon the applicant previous experience, for instance A340 (CFM) course for A320 technicians. If the course is not a complete one, the certificate shall identify whether the interface areas have been covered or not. Text of image Page 2 of 2 MAINTENANCE TRAINING AND EXAMINATION ORGANISATION APPROVAL SCHEDULE Reference: [MEMBER STATE CODE (*)].147.[XXXX] Organisation: [COMPANY NAME AND ADDRESS] This approval schedule is limited to those trainings and examinations specified in the scope of work section of the approved maintenance training organisation exposition. Maintenance training organisation exposition reference: Date of original issue: Date of last revision approved: Revision No: Signed: For the competent authority:[COMPETENT AUTHORITY OF THE MEMBER STATE (*)] EASA Form 11 Issue 5 (*) Or EASA if EASA is the competent authority. (**) Delete as appropriate if the organisation is not approved. (***) Complete with the appropriate rating and limitation. (****) The approval for the Basic B2 course/examination includes approval for B2L course/examination for all system ratings. CLASS LICENCE CATEGORY LIMITATION BASIC (**) B1 (**) TB1.1 (**) AEROPLANES TURBINE (**) TB1.2 (**) AEROPLANES PISTON (**) TB1.3 (**) HELICOPTERS TURBINE (**) TB1.4 (**) HELICOPTERS PISTON (**) B2 (**)/(****) TB2 (**) AVIONICS (**) B2L (**) TB2L (**) AVIONICS (indicate system rating) (**) B3 (**) TB3 (**) PISTON-ENGINE NON-PRESSURISED AEROPLANES 2 000 KG MTOM AND BELOW (**) A (**) TA.1 (**) AEROPLANES TURBINE (**) TA.2 (**) AEROPLANES PISTON (**) TA.3 (**) HELICOPTERS TURBINE (**) TA.4 (**) HELICOPTERS PISTON (**) L (**) (Only examination) TL (**) QUOTE THE SPECIFIC LICENCE SUB-CATEGORY (**) TYPE/TASK (**) C (**) T4 (**) [QUOTE AIRCRAFT TYPE] (***) B1 (**) T1 (**) [QUOTE AIRCRAFT TYPE] (***) B2 (**) T2 (**) [QUOTE AIRCRAFT TYPE] (***) A (**) T3 (**) [QUOTE AIRCRAFT TYPE] (***) ’