These Regulations may be cited as the Supply of Machinery (Safety) (Amendment) Regulations 2011 and come into force on 15th December 2011.
S.I. 2011/2157
The Supply of Machinery (Safety) (Amendment) Regulations 2011 (S.I. 2011/2157)
These Regulations amend the Supply of Machinery (Safety) Regulations 2008 (S.I. 2008/1597) (the “Principal Regulations”) and make consequential amendments to some Northern Ireland Statutory Rules.
Data synced
The Supply of Machinery (Safety) Regulations 2008 are amended as set out in regulations 3 to. 8 .
(1) Regulation 2 (interpretation) is amended as follows.
(2) In paragraph (1)(a), after “Directive 95/16/ EC ” insert “, as amended by Directive 2009/127/EC of the European Parliament and of the Council amending Directive 2006/42/EC with regard to machinery for pesticide application ”.
(3) In paragraph (2)—
(a) for the definition of “essential health and safety requirements” substitute—
“essential health and safety requirements” means the requirements set out in Annex I (Part 1 of Schedule 2), being requirements relating to the design and construction of the products to which these Regulations apply to ensure a high level of protection of the health and safety of persons and, where appropriate, of domestic animals and property and, in the case of machinery referred to in section 2.4 of Annex I, of the environment;
(b) in the definition of “safe”, at the end insert—
or
in the case of machinery referred to in section 2.4 of Annex I (Part 1 of Schedule 2), endanger the environment;
Regulation 9 is revoked.
Paragraph (10) of regulation 16 is revoked.
In regulation 22(1)(a) omit “9”.
After regulation 28 insert—
Review
(29)
(1) Before the end of each review period, the Secretary of State must—
(a) carry out a review of these Regulations,
(b) set out the conclusions of the review in a report, and
(c) publish the report.
(2) In carrying out the review the Secretary of State must, so far as is reasonable, have regard to how the Directive is implemented in other member States.
(3) The report must in particular—
(a) set out the objectives intended to be achieved by the regulatory system established by these Regulations,
(b) assess the extent to which those objectives are achieved, and
(c) assess whether those objectives remain appropriate and, if so, the extent to which they could be achieved with a system that imposes less regulation.
(4) “Review period” means—
(a) the period of five years beginning with 1st December 2009, and
(b) subject to paragraph (5), each successive period of five years.
(5) If a report under this regulation is published before the last day of the review period to which it relates, the following review period is to begin with the day on which that report is published.
Part 1 of Schedule 2 (Annex I: Essential health and safety requirements relating to the design and construction of machinery) is amended as set out in the Schedule to these Regulations.
(1) The Lifting Operations and Lifting Equipment Regulations (Northern Ireland) 1999 are amended as set out in paragraph (2) .
(2) In regulation 2—
(a) omit the definition of “the 1992 Regulations”; and
(b) in the definition of “EC declaration of conformity”, for sub-paragraph (a) substitute—
(a) section A of part 1 of Part 2 of Schedule 2 to the Supply of Machinery (Safety) Regulations 2008;
(3) The Provision and Use of Work Equipment Regulations (Northern Ireland) 1999 are amended as set out in paragraph (4) .
(4) In Schedule 2—
(a) omit the entry relating to the Supply of Machinery (Safety) Regulations 1992 ; and
(b) at the end insert a new entry as follows—
(i) in the first column: “The Supply of Machinery (Safety) Regulations 2008”; and
(ii) in the second column: “ S.I. 2008/1597 , amended by S.I. No. 2011/2157 ”.
Schedules
THE SCHEDULE — AMENDMENTS TO PART 1 OF SCHEDULE 2 TO THE SUPPLY OF MACHINERY (SAFETY) REGULATIONS 2008
For point 4 of the General Principles at the start of Annex I (Essential health and safety requirements relating to the design and construction of machinery) substitute—
(4) This Annex is organised in several parts. The first one is of general scope and applicable to all kinds of machinery. The other parts refer to certain kinds of more specific hazards. Nevertheless, it is essential to examine the whole of this Annex in order to be sure of meeting all the relevant essential requirements. When machinery is being designed, the requirements of the general part and the requirements of one or more of the other parts shall be taken into account, depending on the results of the risk assessment carried out in accordance with point 1 of these General Principles. Essential health and safety requirements for the protection of the environment are applicable only to the machinery referred to in section 2.4.
For the first, unnumbered, paragraph of section 2 of Annex I (Supplementary essential health and safety requirements for certain categories of machinery) substitute—
Foodstuffs machinery, machinery for cosmetics or pharmaceutical products, hand-held and/or hand-guided machinery, portable fixing and other impact machinery, machinery for working wood and material with similar physical characteristics and machinery for pesticide application must meet all the essential health and safety requirements set out in this section (see point 4 of the General Principles at the start of this Annex).
After section 2.3 insert—
Cite this legislation
- Official citation
- S.I. 2011/2157
- Source
- legislation.gov.uk
- Data synced
- Licence
- OGL-3 ↗
The Supply of Machinery (Safety) (Amendment) Regulations 2011 (legislation.gov.uk, OGL-3). Retrieved via LawPlayer, https://lawplayer.com/uk/act/uksi-2011-2157
This text is synced from legislation.gov.uk. In case of any discrepancy, the official version prevails.
Contains public sector information licensed under the Open Government Licence v3.0 (legislation.gov.uk).