2009/381/EC: Commission Decision of 13 May 2009 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices (notified under document number C(2009) 3710) (Text with EEA relevance ) — Full Text

Article 1

The Annex to Decision 2006/771/EC is replaced by the Annex to this Decision.

Article 2

This Decision is addressed to the Member States.

Supplementary provisions

ANNEXSupplementary provisions

ANNEX ‘ANNEX Harmonised frequency bands and technical parameters for short-range devices Type of short-range device Frequency band Power limit/field strength limit/power density limit ( 1 ) Additional parameters/spectrum access and mitigation requirements ( 2 ) Other usage restrictions ( 3 ) Implementation deadline Non-specific short-range devices ( 4 ) 6 765 –6 795 kHz 42 dBμA/m at 10 metres 1 October 2008 13,553–13,567 MHz 42 dBμA/m at 10 metres 1 October 2008 26,957–27,283 MHz 10 mW effective radiated power (e.r.p.), which corresponds to 42 dBμA/m at 10 metres Video applications are excluded 1 June 2007 40,660–40,700 MHz 10 mW e.r.p. Video applications are excluded 1 June 2007 433,050–434,040 ( 5 ) MHz 1 mW e.r.p. and – 13dBm/10 kHz power density for bandwidth modulation larger than 250 kHz Audio and voice signals, and video applications, are excluded 1 October 2008 10 mW e.r.p. Duty cycle ( 6 ) : 10 % Audio and voice signals, and video applications, are excluded 1 June 2007 434,040–434,790 ( 5 ) MHz 1 mW e.r.p. and – 13dBm/10 kHz power density for bandwidth modulation larger than 250 kHz Audio and voice signals, and video applications, are excluded 1 October 2008 10 mW e.r.p. Duty cycle ( 6 ) : 10 % Audio and voice signals, and video applications, are excluded 1 June 2007 Duty cycle ( 6 ) : 100 % subject to channel spacing up to 25 kHz Audio and voice signals, and video applications, are excluded 1 October 2008 863,000–868,000 MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle ( 6 ) of 0,1 % may also be used Audio and voice signals, and video applications, are excluded 1 October 2008 868,000–868,600 ( 5 ) MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle ( 6 ) of 1 % may also be used Video applications are excluded 1 October 2008 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle ( 6 ) of 0,1 % may also be used Audio and voice signals, and video applications, are excluded 1 October 2008 868,700–869,200 ( 5 ) MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle ( 6 ) of 0,1 % may also be used Video applications are excluded 1 October 2008 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle ( 6 ) of 0,1 % may also be used Audio and voice signals, and video applications, are excluded 1 October 2008 869,400–869,650 ( 5 ) MHz 500 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle ( 6 ) of 10 % may also be used Channel spacing must be 25 kHz, except that the whole band may also be used as a single channel for high-speed data transmission Video applications are excluded 1 October 2008 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle ( 6 ) of 0,1 % may also be used Audio and voice signals, and video applications, are excluded 1 October 2008 869,700–870,000 ( 5 ) MHz 5 mW e.r.p. Voice applications allowed with advanced mitigation techniques Audio and video applications are excluded 1 June 2007 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle ( 6 ) of 0,1 % may also be used Audio and voice signals, and video applications, are excluded 1 October 2008 2 400 –2 483,5 MHz 10 mW equivalent isotropic radiated power (e.i.r.p.) 1 June 2007 5 725 –5 875 MHz 25 mW e.i.r.p. 1 June 2007 24,150–24,250 GHz 100 mW e.i.r.p. 1 October 2008 61,0–61,5 GHz 100 mW e.i.r.p. 1 October 2008 Wideband data transmission systems 2 400 –2 483,5 MHz 100 mW e.i.r.p. and 100 mW/100 kHz e.i.r.p. density applies when frequency hopping modulation is used, 10 mW/MHz e.i.r.p. density applies when other types of modulation are used Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used 1 November 2009 57,0–66,0 ( 5 ) GHz 40 dBm e.i.r.p. and 13 dBm/MHz e.i.r.p. density Outdoor applications are excluded 1 November 2009 25 dBm e.i.r.p. and – 2 dBm/MHz e.i.r.p. density Fixed outdoor installations are excluded 1 November 2009 Alarm systems 868,600–868,700 MHz 10 mW e.r.p. Channel spacing: 25 kHz The whole frequency band may also be used as a single channel for high-speed data transmission Duty cycle ( 6 ) : 1,0 % 1 October 2008 869,250–869,300 MHz 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle ( 6 ) : 0,1 % 1 June 2007 869,300–869,400 MHz 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle ( 6 ) : 1,0 % 1 October 2008 869,650–869,700 MHz 25 mW e.r.p. Channel spacing: 25 kHz Duty cycle ( 6 ) : 10 % 1 June 2007 Social alarms ( 7 ) 869,200–869,250 MHz 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle ( 6 ) : 0,1 % 1 June 2007 Inductive applications ( 8 ) 20,050–59,750 kHz 72 dBμA/m at 10 metres 1 June 2007 59,750–60,250 kHz 42 dBμA/m at 10 metres 1 June 2007 60,250–70,000 kHz 69 dBμA/m at 10 metres 1 June 2007 70–119 kHz 42 dBμA/m at 10 metres 1 June 2007 119–127 kHz 66 dBμA/m at 10 metres 1 June 2007 127–140 kHz 42 dBμA/m at 10 metres 1 October 2008 140–148,5 kHz 37,7 dBμA/m at 10 metres 1 October 2008 148,5–5 000 kHz In the specific bands mentioned below, higher field strengths and additional usage restrictions apply: – 15 dBμA/m at 10 metres in any bandwidth of 10 kHz Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz 1 October 2008 400–600 kHz – 8 dBμA/m at 10 metres This set of usage conditions applies to RFID ( 9 ) only 1 October 2008 3 155 –3 400 kHz 13,5 dBμA/m at 10 metres 1 October 2008 5 000 –30 000 kHz In the specific bands mentioned below, higher field strengths and additional usage restrictions apply: – 20 dBμA/m at 10 metres in any bandwidth of 10 kHz Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz 1 October 2008 6 765 –6 795 kHz 42 dBμA/m at 10 metres 1 June 2007 7 400 –8 800 kHz 9 dBμA/m at 10 metres 1 October 2008 10 200 –11 000 kHz 9 dBμA/m at 10 metres 1 October 2008 13 553 –13 567 kHz 42 dBμA/m at 10 metres 1 June 2007 60 dBμA/m at 10 metres This set of usage conditions applies to RFID ( 9 ) and EAS ( 10 ) only 1 October 2008 26 957 –27 283 kHz 42 dBμA/m at 10 metres 1 October 2008 Active medical implants ( 11 ) 9–315 kHz 30 dBμA/m at 10 m Duty cycle ( 6 ) : 10 % 1 October 2008 402–405 MHz 25 μW e.r.p. Channel spacing: 25 kHz Individual transmitters may combine adjacent channels for increased bandwidth up to 300 kHz. Other techniques to access spectrum or mitigate interference, including bandwidths greater than 300 kHz, can be used provided they result at least in an equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC to ensure compatible operation with the other users and in particular with meteorological radiosondes. 1 November 2009 Wireless audio applications ( 12 ) 87,5–108,0 MHz 50 nW e.r.p. Channel spacing up to 200 kHz 1 October 2008 863–865 MHz 10 mW e.r.p. 1 June 2007 Radio determination applications ( 13 ) 2 400 –2 483,5 MHz 25 mW e.i.r.p. 1 November 2009 17,1–17,3 GHz 26 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions applies to ground based systems only 1 November 2009 Tank Level Probing Radar ( 14 ) 4,5–7,0 GHz 24 dBm e.i.r.p. ( 15 ) 1 November 2009 8,5–10,6 GHz 30 dBm e.i.r.p. ( 15 ) 1 November 2009 24,05–27,0 GHz 43 dBm e.i.r.p. ( 15 ) 1 November 2009 57,0–64,0 GHz 43 dBm e.i.r.p. ( 15 ) 1 November 2009 75,0–85,0 GHz 43 dBm e.i.r.p. ( 15 ) 1 November 2009 Model Control ( 16 ) 26 990 –27 000 kHz 100 mW e.r.p. 1 November 2009 27 040 –27 050 kHz 100 mW e.r.p. 1 November 2009 27 090 –27 100 kHz 100 mW e.r.p. 1 November 2009 27 140 –27 150 kHz 100 mW e.r.p. 1 November 2009 27 190 –27 200 kHz 100 mW e.r.p. 1 November 2009 Radio Frequency Identification (RFID) 2 446 –2 454 MHz 100 mW e.i.r.p. 1 November 2009 ( 1 ) Member States must allow the usage of spectrum up to the power, field strength or power density given in this table. In conformity with Article 3(3) of Decision 2006/771/EC, they may impose less restrictive conditions, i.e. allow the use of spectrum with higher power, field strength or power density. ( 2 ) Member States may only impose these “additional parameters/spectrum access and mitigation requirements”, and may not add other parameters or spectrum access and mitigation requirements. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may completely omit the parameters/spectrum access and mitigation requirements in a given cell or allow higher values. ( 3 ) Member States may only impose these “other usage restrictions”, and may not add additional usage restrictions. As less restrictive conditions may be introduced within the meaning of Article 3(3) of Decision 2006/771/EC, Member States may omit one or all of these restrictions. ( 4 ) This category is available for any type of application which fulfils the technical conditions (typical uses are telemetry, telecommand, alarms, data in general and other similar applications). ( 5 ) For this frequency band Member States must make all the alternative sets of usage conditions possible. ( 6 ) “Duty cycle” means the ratio of time during any one-hour period when equipment is actively transmitting. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may allow a higher value for “Duty cycle”. ( 7 ) Social alarm devices are used to assist elderly or disabled people when they are in distress. ( 8 ) This category covers, for example, devices for car immobilisation, animal identification, alarm systems, cable detection, waste management, personal identification, wireless voice links, access control, proximity sensors, anti-theft systems, including RF anti-theft induction systems, data transfer to handheld devices, automatic article identification, wireless control systems and automatic road tolling. ( 9 ) This category covers inductive applications used for Radio Frequency Identification (RFID). ( 10 ) This category covers inductive applications used for Electronic Article Surveillance (EAS). ( 11 ) This category covers the radio part of active implantable medical devices, as defined in Council Directive 90/385/EEC of 20 June 1990 on the approximation of the laws of the Member States relating to active implantable medical devices ( OJ L 189, 20.7.1990, p. 17 ). ( 12 ) Applications for wireless audio systems, including: cordless loudspeakers; cordless headphones; cordless headphones for portable use, e.g. portable CD, cassette or radio devices carried on a person; cordless headphones for use in a vehicle, for example for use with a radio or mobile telephone, etc.; in-ear monitoring, for use at concerts or other stage productions. ( 13 ) This category covers applications used for determining the position, velocity and/or other characteristics of an object, or for obtaining information relating to these parameters. ( 14 ) Tank Level Probing Radars (TLPR) are a specific type of radiodetermination application, which are used for tank level measurements and are installed in metallic or reinforced concrete tanks, or similar structures made of material with comparable attenuation characteristics. The purpose of the tank is to contain a substance. ( 15 ) The power limit applies inside a closed tank and corresponds with a spectral density of – 41,3 dBm/MHz e.i.r.p. outside a 500 litre test tank. ( 16 ) This category covers applications used to control the movement of models (principally miniature representations of vehicles) in the air, on land or over or under the water surface.’

Article 1

Article 2

Supplementary provisions

ANNEXSupplementary provisions

What to look at next