LawPlayer
My bookmarksSign up freeSign up free
Source

2010/115/EU: Commission Decision of 23 February 2010 amending Annex II to Directive 2000/53/EC of the European Parliament and of the Council on end-of-life vehicles (notified under document C(2010) 972) (Text with EEA relevance)

2010/115/EU: Commission Decision of 23 February 2010 amending Annex II to Directive 2000/53/EC of the European Parliament and of the Council on end-of-life vehicles (notified under document C(2010) 972) (Text with EEA relevance)

Directive 2000/53/EC · Decision · 3 articles

Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗

Article 1

Open ↗

Annex II to Directive 2000/53/EC is replaced by the text set out in the Annex to this Decision.

Supplementary provisions

ANNEXSupplementary provisions

Open ↗

ANNEX ‘ANNEX II Materials and components exempt from Article 4(2)(a) Materials and components Scope and expiry date of the exemption To be labelled or made identifiable in accordance with Article 4(2)(b)(iv) Lead as an alloying element 1. Steel for machining purposes and galvanised steel containing up to 0,35 % lead by weight     2(a). Aluminium for machining purposes with a lead content up to 2 % by weight As spare parts for vehicles put on the market before 1 July 2005   2(b). Aluminium with a lead content up to 1,5 % by weight As spare parts for vehicles put on the market before 1 July 2008   2(c). Aluminium with a lead content up to 0,4 % by weight     3. Copper alloy containing up to 4 % lead by weight     4(a). Bearing shells and bushes As spare parts for vehicles put on the market before 1 July 2008   4(b). Bearing shells and bushes in engines, transmissions and air conditioning compressors 1 July 2011 and after that date as spare parts for vehicles put on the market before 1 July 2011   Lead and lead compounds in components 5. Batteries   X 6. Vibration dampers   X 7(a). Vulcanising agents and stabilisers for elastomers in brake hoses, fuel hoses, air ventilation hoses, elastomer/metal parts in the chassis applications, and engine mountings As spare parts for vehicles put on the market before 1 July 2005   7(b). Vulcanising agents and stabilisers for elastomers in brake hoses, fuel hoses, air ventilation hoses, elastomer/metal parts in the chassis applications, and engine mountings containing up to 0,5 % lead by weight As spare parts for vehicles put on the market before 1 July 2006   7(c). Bonding agents for elastomers in power-train applications containing up to 0,5 % lead by weight As spare parts for vehicles put on the market before 1 July 2009   8(a). Lead in solders to attach electrical and electronic components to electronic circuit boards and lead in finishes on terminations of components other than electrolyte aluminium capacitors, on component pins and on electronic circuit boards Vehicles type approved before 1 January 2016 and spare parts for these vehicles X  ( 1 ) 8(b). Lead in solders in electrical applications other than soldering on electronic circuit boards or on glass Vehicles type approved before 1 January 2011 and spare parts for these vehicles X  ( 1 ) 8(c). Lead in finishes on terminals of electrolyte aluminium capacitors Vehicles type approved before 1 January 2013 and spare parts for these vehicles X  ( 1 ) 8(d). Lead used in soldering on glass in mass airflow sensors Vehicles type approved before 1 January 2015 and spare parts of such vehicles X  ( 1 ) 8(e). Lead in high melting temperature type solders (i.e. lead-based alloys containing 85 % by weight or more lead)  ( 2 ) X  ( 1 ) 8(f). Lead in compliant pin connector systems  ( 2 ) X  ( 1 ) 8(g). Lead in solders to complete a viable electrical connection between semiconductor die and carrier within integrated circuit flip chip packages  ( 2 ) X  ( 1 ) 8(h). Lead in solder to attach heat spreaders to the heat sink in power semiconductor assemblies with a chip size of at least 1 cm 2 of projection area and a nominal current density of at least 1 A/mm 2 of silicon chip area  ( 2 ) X  ( 1 ) 8(i). Lead in solders in electrical glazing applications on glass except for soldering in laminated glazing Vehicles type approved before 1 January 2013 and spare parts for these vehicles  ( 3 ) X  ( 1 ) 8(j). Lead in solders for soldering in laminated glazing  ( 2 ) X  ( 1 ) 9. Valve seats As spare parts for engine types developed before 1 July 2003   10. Electrical components which contain lead in a glass or ceramic matrix compound except glass in bulbs and glaze of spark plugs   X  ( 4 ) (for components other than piezo in engines) 11. Pyrotechnic initiators Vehicles type-approved before 1 July 2006 and spare parts for these vehicles   Hexavalent chromium 12(a). Corrosion preventive coatings As spare parts for vehicles put on the market before 1 July 2007   12(b). Corrosion preventive coatings related to bolt and nut assemblies for chassis applications As spare parts for vehicles put on the market before 1 July 2008   13. Absorption refrigerators in motor caravans     Mercury 14(a). Discharge lamps for headlight application Vehicles type approved before 1 July 2012 and spare parts for these vehicles   14(b). Fluorescent tubes used in instrument panel displays Vehicles type approved before 1 July 2012 and spare parts for these vehicles   Cadmium 15. Batteries for electrical vehicles As spare parts for vehicles put on the market before 31 December 2008   Notes: A maximum concentration value up to 0,1 % by weight and in homogeneous material, for lead, hexavalent chromium and mercury and up to 0,01 % by weight in homogeneous material for cadmium shall be tolerated. The reuse of parts of vehicles which were already on the market at the date of expiry of an exemption shall be allowed without limitation since it is not covered by Article 4(2)(a). Spare parts put on the market after 1 July 2003 which are used for vehicles put on the market before 1 July 2003 shall be exempted from the provisions of Article 4(2)(a)  ( *1 ) . ( *1 )   This clause shall not apply to wheel balance weights, carbon brushes for electric motors and brake linings.’ ’ ( 1 )   Dismantling if, in correlation with entry 10, an average threshold of 60 grams per vehicle is exceeded. For the application of this clause electronic devices not installed by the manufacturer on the production line shall not be taken into account. ( 2 )   This exemption shall be reviewed in 2014. ( 3 )   This exemption shall be reviewed before 1 January 2012. ( 4 )   Dismantling if, in correlation with entries 8(a) to 8(j), an average threshold of 60 grams per vehicle is exceeded. For the application of this clause electronic devices not installed by the manufacturer on the production line shall not be taken into account.

Other acts of the same type
Council Decision (CFSP) 2026/1464 of 26 June 2026 on an assistance measure under the European Peace Facility to support the Togolese Armed ForcesCouncil Decision (EU) 2026/1527 of 26 June 2026 authorising the opening of negotiations for an agreement between the Union and the Republic of India on the participation of the Republic of India in Union programmes and the association of the Republic of India to Pillar II of Horizon Europe – the Framework Programme for Research and Innovation (2021-2027)Council Decision of 25 June 2026 replacing a member of the Management Board of the European Foundation for the improvement of living and working conditions for LuxembourgCouncil Decision of 25 June 2026 replacing an alternate member of the Management Board of the European Foundation for the improvement of living and working conditions for SpainCommission Implementing Decision (EU) 2026/1426 of 25 June 2026 amending the Annex to Implementing Decision (EU) 2023/2447 concerning emergency measures in relation to outbreaks of highly pathogenic avian influenza in certain Member States (notified under document C(2026) 4549)Council Decision (CFSP) 2026/1437 of 25 June 2026 amending Decision 2014/512/CFSP concerning restrictive measures in view of Russia’s actions destabilising the situation in UkraineCouncil Decision (EU) 2026/1439 of 25 June 2026 authorising the opening of negotiations for protocols between the Union and Iceland, the Kingdom of Norway, the Swiss Confederation and the Principality of Liechtenstein supplementing their respective agreements and protocol concerning the criteria and mechanisms for establishing the State responsible for examining a request for asylum lodged in those countries, to include rules to enable their participation in Parts II and IV of Regulation (EU) 2024/1351 of the European Parliament and of the Council and in Chapters II and III of Regulation (EU) 2024/1359 of the European Parliament and of the CouncilCouncil Implementing Decision (EU) 2026/1440 of 25 June 2026 authorising Germany to apply a reduced rate of taxation to electricity directly supplied to vessels berthed in ports, in accordance with Article 19 of Directive 2003/96/ECCommission Implementing Decision (EU) 2026/1441 of 25 June 2026 approving the United States’ request for reciprocal access under the Ukraine Facility established by Regulation (EU) 2024/792 of the European Parliament and of the CouncilCommission Implementing Decision (EU) 2026/1442 of 25 June 2026 approving Canada’s request for reciprocal access under the Ukraine Facility established by Regulation (EU) 2024/792 of the European Parliament and of the CouncilCommission Implementing Decision (EU) 2026/1449 of 25 June 2026 approving Japan’s request for reciprocal access under the Ukraine Facility established by Regulation (EU) 2024/792 of the European Parliament and of the CouncilCouncil Implementing Decision (EU) 2026/1454 of 25 June 2026 on the suspension of certain provisions of Regulation (EC) No 810/2009 of the European Parliament and of the Council in respect of Somalia

Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.

Contents

What to look at next