LawPlayer
My bookmarksSign up freeSign up free
Source

2011/284/EU: Commission Decision of 12 May 2011 on the procedure for attesting the conformity of construction products pursuant to Article 20(2) of Council Directive 89/106/EEC as regards power, control and communication cables (notified under document C(2011) 3107) Text with EEA relevance

2011/284/EU: Commission Decision of 12 May 2011 on the procedure for attesting the conformity of construction products pursuant to Article 20(2) of Council Directive 89/106/EEC as regards power, control and communication cables (notified under document C(2011) 3107) Text with EEA relevance

Directive 89/106/EEC · Decision · 7 articles

Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗

Article 1

Open ↗

The products and families of products set out in Annex I shall have their conformity attested by a procedure whereby the manufacturer has under its sole responsibility a factory production control system ensuring that the product is in conformity with the relevant technical specifications.

Article 2

Open ↗

The products and families of products set out in Annex II shall have their conformity attested by a procedure whereby, in addition to a factory production control system operated by the manufacturer, an approved certification body is involved in the assessment and surveillance of the production control or of the product itself.

Article 3

Open ↗

The choice of procedure for attesting conformity as set out in Annex III shall be indicated in the relevant technical specifications.

Supplementary provisions

ANNEX ISupplementary provisions

Open ↗

ANNEX I Power, control and communication cables   ( 1 ) : For uses in buildings and other civil engineering works subject to regulations on dangerous substances and/or reaction to fire, except for products made of materials falling into classes A ca , B1 ca , B2 ca , C ca . ( 1 )   Power, control and communication cables designed for use with a voltage rating of between 50 and 1 000 V for alternating current and between 75 and 1 500 V for direct current are also subject to the provisions of Council Directive 73/23/EEC, known as the ‘Low Voltage Directive’ ( OJ L 77, 26.3.1973, p. 29 ).

ANNEX IISupplementary provisions

Open ↗

ANNEX II Power, control and communication cables   ( 1 ) : For uses in buildings and other civil engineering works subject to reaction-to-fire regulations for products made of materials falling into classes A ca , B1 ca , B2 ca , C ca and/or resistance-to-fire regulations. ( 1 )   Power, control and communication cables designed for use with a voltage rating of between 50 and 1 000 V for alternating current and between 75 and 1 500 V for direct current are also subject to the provisions of Council Directive 73/23/EEC, known as the ‘Low Voltage Directive’ ( OJ L 77, 26.3.1973, p. 29 ).

ANNEX IIISupplementary provisions

Open ↗

ANNEX III Note : for products having more than one of the intended uses specified in the following families, the tasks for the approved body, derived from the relevant systems of attestation of conformity, are cumulative. PRODUCT FAMILY POWER, CONTROL AND COMMUNICATION CABLES (1/3) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec is requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): Product(s) Intended use(s) Level(s) or class(es) (reaction to fire) Attestation of conformity system(s) Power, control and communication cables for uses subject to regulations on reaction to fire A ca , B1 ca , B2 ca , C ca 1 + D ca , E ca 3 F ca 4 System 1+ : see point (i) of Section 2 of Annex III to Directive 89/106/EEC, with audit-testing of samples taken at the factory. System 3 : see point (ii) of Section 2 of Annex III to Directive 89/106/EEC, second possibility. System 4 : see point (ii) of Section 2 of Annex III to Directive 89/106/EEC, third possibility. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY POWER, CONTROL AND COMMUNICATION CABLES (2/3) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): Product(s) Intended use(s) Level(s) or class(es) (resistance to fire) Attestation of conformity system(s) Power, control and communication cables for uses subject to fire regulations on resistance to fire P15 – P30 – P60 – P90 – P120 PH15  ( *1 ) – PH  ( *1 ) 30 – PH  ( *1 ) 60 – PH  ( *1 ) 90 – PH  ( *1 )  120 1 + System 1 + : see point (i) of Section 2 of Annex III to Directive 89/106/EEC, with audit-testing of samples taken at the factory. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. PRODUCT FAMILY POWER, CONTROL AND COMMUNICATION CABLES (3/3) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonised standard(s): Product(s) Intended use(s) Level(s) or class(es) Attestation of conformity system(s) Power, control and communication cables for uses subject to regulations on dangerous substances — 3 System 3 : see point (ii) of Section 2 of Annex III to Directive 89/106/EEC, second possibility. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect. ( *1 )   Applies to small diameter power or signal cables or systems (< 20 mm diameter and with conductor sizes ≤ 2,5 mm 2 ).

Other acts of the same type
Council Decision (CFSP) 2026/345 of 11 February 2026 appointing the European Union Special Representative for Human RightsCouncil Decision (CFSP) 2026/354 of 11 February 2026 amending Decision (CFSP) 2025/144 appointing the European Union Special Representative for the Belgrade-Pristina DialogueCouncil Implementing Decision (EU) 2026/368 of 11 February 2026 on making the financial assistance under Regulation (EU) 2025/1106 available to RomaniaCouncil Implementing Decision (EU) 2026/369 of 11 February 2026 on making the financial assistance under Regulation (EU) 2025/1106 available to PortugalCouncil Implementing Decision (EU) 2026/370 of 11 February 2026 on making the financial assistance under Regulation (EU) 2025/1106 available to SpainCouncil Implementing Decision (EU) 2026/417 of 11 February 2026 on making the financial assistance under Regulation (EU) 2025/1106 available to CroatiaCouncil Implementing Decision (EU) 2026/418 of 11 February 2026 on making the financial assistance under Regulation (EU) 2025/1106 available to DenmarkCouncil Implementing Decision (EU) 2026/435 of 11 February 2026 on making the financial assistance under Regulation (EU) 2025/1106 available to BulgariaCouncil Implementing Decision (EU) 2026/436 of 11 February 2026 on making the financial assistance under Regulation (EU) 2025/1106 available to BelgiumCouncil Implementing Decision (EU) 2026/437 of 11 February 2026 on making the financial assistance under Regulation (EU) 2025/1106 available to CyprusCouncil Decision (EU) 2026/444 of 11 February 2026 on the signing and provisional application of the Agreement between the European Union and Canada laying down the conditions for the participation of Canadian legal entities and products originating in Canada to procurement under the SAFE InstrumentCouncil Decision (EU) 2026/523 of 11 February 2026 on the position to be taken on behalf of the European Union within the Regional Steering Committee of the Transport Community as regards certain changes to the rules on staff salaries of the Transport Community Permanent Secretariat

Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.

Contents

What to look at next