Article 1
The Annex to Decision 2006/771/EC is replaced by the text in the Annex to this Decision.
2011/829/EU: Commission Implementing Decision of 8 December 2011 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices (notified under document C(2011) 9030) Text with EEA relevance
2011/829/EU: Commission Implementing Decision of 8 December 2011 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices (notified under document C(2011) 9030) Text with EEA relevance
Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗
Article 2
This Decision is addressed to the Member States.
Supplementary provisions
ANNEXSupplementary provisions
ANNEX ‘ANNEX Harmonised frequency bands and technical parameters for short-range devices Type of short-range device Frequency band ( 1 ) Transmit power limit/field strength limit/power density limit ( 2 ) Additional parameters (channelling and/or channel access and occupation rules) ( 3 ) Other usage restrictions ( 4 ) Implementation deadline Non-specific short-range devices ( 5 ) 6 765 –6 795 kHz 42 dBμA/m at 10 metres 1 October 2008 13,553–13,567 MHz 42 dBμA/m at 10 metres 1 October 2008 26,957–27,283 MHz 10 mW effective radiated power (e.r.p.), which corresponds to 42 dBμA/m at 10 metres Video applications are excluded 1 June 2007 40,660–40,700 MHz 10 mW e.r.p. Video applications are excluded 1 June 2007 433,050–434,040 ( 6 ) MHz 1 mW e.r.p. and - 13dBm/10 kHz power density for bandwidth modulation larger than 250 kHz Voice applications allowed with advanced mitigation techniques Audio and video applications are excluded 1 November 2010 10 mW e.r.p. Duty cycle limit ( 7 ) : 10 % Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 434,040–434,790 ( 6 ) MHz 1 mW e.r.p. and – 13dBm/10 kHz power density for bandwidth modulation larger than 250 kHz Voice applications allowed with advanced mitigation techniques Audio and video applications are excluded 1 November 2010 10 mW e.r.p. Duty cycle limit ( 7 ) : 10 % Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 Duty cycle limit ( 7 ) : 100 % subject to channel spacing up to 25 kHz Voice applications allowed with advanced mitigation techniques Audio and video applications are excluded 1 November 2010 Non-specific short-range devices (cont.) 863,000–865,000 MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 865,000–868,000 MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 1 % may also be used Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 868,000–868,600 MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 1 % may also be used Analogue video applications are excluded 1 November 2010 868,700–869,200 MHz 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used Analogue video applications are excluded 1 November 2010 869,400–869,650 ( 6 ) MHz 500 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 10 % may also be used Channel spacing must be 25 kHz, except that the whole band may also be used as a single channel for high-speed data transmission Analogue video applications are excluded 1 November 2010 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 Non-specific short-range devices (cont.) 869,700–870,000 ( 6 ) MHz 5 mW e.r.p. Voice applications allowed with advanced mitigation techniques Audio and video applications are excluded 1 June 2007 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 1 % may also be used Analogue audio applications other than voice are excluded. Analogue video applications are excluded 1 November 2010 2 400 –2 483,5 MHz 10 mW equivalent isotropic radiated power (e.i.r.p.) 1 June 2007 5 725 –5 875 MHz 25 mW e.i.r.p. 1 June 2007 24,150–24,250 GHz 100 mW e.i.r.p. 1 October 2008 61,0–61,5 GHz 100 mW e.i.r.p. 1 October 2008 122–123 GHz 100 mW e.i.r.p. 1 June 2012 244–246 GHz 100 mW e.i.r.p. 1 June 2012 Wideband data transmission systems 2 400 –2 483,5 MHz 100 mW e.i.r.p. and 100 mW/100 kHz e.i.r.p. density applies when frequency hopping modulation is used, 10 mW/MHz e.i.r.p. density applies when other types of modulation are used Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used 1 November 2009 57,0–66,0 GHz 40 dBm e.i.r.p. and 13 dBm/MHz e.i.r.p. density Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used Fixed outdoor installations are excluded 1 November 2010 Alarm systems 868,600–868,700 MHz 10 mW e.r.p. Channel spacing: 25 kHz The whole frequency band may also be used as a single channel for high-speed data transmission Duty cycle limit ( 7 ) : 1,0 % 1 October 2008 869,250–869,300 MHz 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit ( 7 ) : 0,1 % 1 June 2007 869,300–869,400 MHz 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit ( 7 ) : 1,0 % 1 October 2008 869,650–869,700 MHz 25 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit ( 7 ) : 10 % 1 June 2007 Social alarms ( 8 ) 869,200–869,250 MHz 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit ( 7 ) : 0,1 % 1 June 2007 Inductive applications ( 9 ) 9,000–59,750 kHz 72 dBμA/m at 10 metres 1 November 2010 59,750–60,250 kHz 42 dBμA/m at 10 metres 1 June 2007 60,250–74,750 kHz 72 dBμA/m at 10 metres 1 June 2012 74,750–75,250 kHz 42 dBμA/m at 10 metres 1 June 2012 75,250–77,250 kHz 72 dBμA/m at 10 metres 1 June 2012 77,250–77,750 kHz 42 dBμA/m at 10 metres 1 June 2012 77,750–90 kHz 72 dBμA/m at 10 metres 1 June 2012 90–119 kHz 42 dBμA/m at 10 metres 1 June 2012 119–128,6 kHz 66 dBμA/m at 10 metres 1 June 2012 128,6–129,6 kHz 42 dBμA/m at 10 metres 1 June 2012 129,6–135 kHz 66 dBμA/m at 10 metres 1 June 2012 135–140 kHz 42 dBμA/m at 10 metres 1 June 2012 140–148,5 kHz 37,7 dBμA/m at 10 metres 1 October 2008 148,5–5 000 kHz In the specific bands mentioned below, higher field strengths and additional usage restrictions apply: – 15 dBμA/m at 10 metres in any bandwidth of 10 kHz Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz 1 October 2008 Inductive applications (cont.) 400–600 kHz – 8 dBμA/m at 10 metres This set of usage conditions applies to RFID ( 10 ) only 1 October 2008 3 155 –3 400 kHz 13,5 dBμA/m at 10 metres 1 October 2008 5 000 –30 000 kHz In the specific bands mentioned below, higher field strengths and additional usage restrictions apply: – 20 dBμA/m at 10 metres in any bandwidth of 10 kHz Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz 1 October 2008 6 765 –6 795 kHz 42 dBμA/m at 10 metres 1 June 2007 7 400 –8 800 kHz 9 dBμA/m at 10 metres 1 October 2008 10 200 –11 000 kHz 9 dBμA/m at 10 metres 1 October 2008 13 553 –13 567 kHz 42 dBμA/m at 10 metres 1 June 2007 60 dBμA/m at 10 metres This set of usage conditions applies to RFID ( 10 ) and EAS ( 11 ) only 1 October 2008 26 957 –27 283 kHz 42 dBμA/m at 10 metres 1 October 2008 Active medical implants ( 12 ) 9–315 kHz 30 dBμA/m at 10m Duty cycle limit ( 7 ) : 10 % 1 October 2008 30,0–37,5 MHz 1 mW e.r.p. Duty cycle limit ( 7 ) : 10 % This set of usage conditions applies to ultra low power medical membrane implants for blood pressure measurements only 1 November 2010 402–405 MHz 25 μW e.r.p. Channel spacing: 25 kHz Individual transmitters may combine adjacent channels for increased bandwidth up to 300 kHz. Other techniques to access spectrum or mitigate interference, including bandwidths greater than 300 kHz, can be used provided they result at least in an equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC to ensure compatible operation with the other users and in particular with meteorological radiosondes 1 November 2009 Active medical implants and associated peripherals ( 13 ) 401–402 MHz 25 μW e.r.p. Channel spacing: 25 kHz Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used 1 November 2010 405–406 MHz 25 μW e.r.p. Channel spacing: 25 kHz Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit ( 7 ) of 0,1 % may also be used 1 November 2010 Animal implantable devices ( 14 ) 315–600 kHz – 5 dΒμΑ/m at 10m Duty cycle limit ( 7 ) : 10 % 1 November 2010 12,5–20,0 MHz – 7 dΒμΑ/m at 10m in a bandwidth of 10 kHz Duty cycle limit ( 7 ) : 10 % This set of usage conditions applies to indoor applications only 1 November 2010 Low power FM transmitters ( 15 ) 87,5–108,0 MHz 50 nW e.r.p. Channel spacing up to 200 kHz 1 November 2010 Wireless audio applications ( 16 ) 863–865 MHz 10 mW e.r.p. 1 November 2010 Radio determination applications ( 17 ) 2 400 –2 483,5 MHz 25 mW e.i.r.p. 1 November 2009 17,1–17,3 GHz 26 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used This set of usage conditions applies to ground-based systems only 1 November 2009 Tank level probing radar ( 18 ) 4,5–7,0 GHz 24 dBm e.i.r.p. ( 19 ) 1 November 2009 8,5–10,6 GHz 30 dBm e.i.r.p. ( 19 ) 1 November 2009 24,05–27,0 GHz 43 dBm e.i.r.p. ( 19 ) 1 November 2009 57,0–64,0 GHz 43 dBm e.i.r.p. ( 19 ) 1 November 2009 75,0–85,0 GHz 43 dBm e.i.r.p. ( 19 ) 1 November 2009 Model control ( 20 ) 26 990 –27 000 kHz 100 mW e.r.p. 1 November 2009 27 040 –27 050 kHz 100 mW e.r.p. 1 November 2009 27 090 –27 100 kHz 100 mW e.r.p. 1 November 2009 27 140 –27 150 kHz 100 mW e.r.p. 1 November 2009 27 190 –27 200 kHz 100 mW e.r.p. 1 November 2009 Radio frequency identification (RFID) 2 446 –2 454 MHz 500 mW e.i.r.p. 1 June 2012 Road transport and traffic telematics 24,050–24,075 GHz 100 mW e.i.r.p. 1 June 2012 24,075–24,150 GHz 0,1 mW e.i.r.p. 1 June 2012 24,075–24,150 GHz 100 mW e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used Dwell time limits and frequency modulation range apply as specified in harmonised standards This set of usage conditions applies to vehicle radars only 1 June 2012 24,150–24,250 GHz 100 mW e.i.r.p. 1 June 2012 63–64 GHz 40 dBm e.i.r.p. This set of usage conditions applies to vehicle-to-vehicle, vehicle-to-infrastructure and infrastructure-to-vehicle systems only 1 June 2012 76,0–77,0 GHz 55 dBm peak e.i.r.p. and 50 dBm mean e.i.r.p. and 23,5 dBm mean e.i.r.p. for pulse radars This set of usage conditions applies to terrestrial vehicle and infrastructure systems only 1 November 2010 ( 1 ) Member States must allow the usage of adjacent frequency bands within this table as a single frequency band provided the specific conditions of each of these adjacent frequency bands are met. ( 2 ) Member States must allow the usage of spectrum up to the transmit power, field strength or power density given in this table. In conformity with Article 3(3) of Decision 2006/771/EC, they may impose less restrictive conditions, i.e. allow the use of spectrum with higher transmit power, field strength or power density. ( 3 ) Member States may only impose these “additional parameters (channelling and/or channel access and occupation rules)”, and may not add other parameters or spectrum access and mitigation requirements. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may completely omit the “additional parameters (channelling and/or channel access and occupation rules)” in a given cell or allow higher values. ( 4 ) Member States may only impose these “other usage restrictions”, and may not add additional usage restrictions. As less restrictive conditions may be introduced within the meaning of Article 3(3) of Decision 2006/771/EC, Member States may omit one or all of these restrictions. ( 5 ) This category is available for any type of application which fulfils the technical conditions (typical uses are telemetry, telecommand, alarms, data in general and other similar applications). ( 6 ) For this frequency band Member States must make all the alternative sets of usage conditions possible. ( 7 ) “Duty cycle” means the ratio of time during any one-hour period when equipment is actively transmitting. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may allow a higher value for “Duty cycle”. ( 8 ) Social alarm devices are used to assist elderly or disabled people when they are in distress. ( 9 ) This category covers, for example, devices for car immobilisation, animal identification, alarm systems, cable detection, waste management, personal identification, wireless voice links, access control, proximity sensors, anti-theft systems, including RF anti-theft induction systems, data transfer to handheld devices, automatic article identification, wireless control systems and automatic road tolling. ( 10 ) This category covers inductive applications used for radio frequency identification (RFID). ( 11 ) This category covers inductive applications used for electronic article surveillance (EAS). ( 12 ) This category covers the radio part of active implantable medical devices, as defined in Council Directive 90/385/EEC of 20 June 1990 on the approximation of the laws of the Member States relating to active implantable medical devices ( OJ L 189, 20.7.1990, p. 17 ). ( 13 ) This category covers systems specifically designed for the purpose of providing non-voice digital communications between active medical implants, as defined in footnote 19, and/or body-worn devices and other devices external to the human body used for transferring non-time critical individual patient-related physiological information. ( 14 ) This category covers transmitting devices which are placed inside the body of an animal for the purpose of performing diagnostic functions and/or delivery of therapeutic treatment. ( 15 ) This category includes applications which connect personal audio devices, including mobile phones, and the automotive or home entertainment system. ( 16 ) Applications for wireless audio systems, including: wireless microphones; cordless loudspeakers; cordless headphones; cordless headphones for portable use, e.g. portable CD, cassette or radio devices carried on a person; cordless headphones for use in a vehicle, for example for use with a radio or mobile telephone, etc.; in-ear monitoring and wireless microphones for use at concerts or other stage productions. ( 17 ) This category covers applications used for determining the position, velocity and/or other characteristics of an object, or for obtaining information relating to these parameters. ( 18 ) Tank level probing radars (TLPR) are a specific type of radio-determination application, which are used for tank level measurements and are installed in metallic or reinforced concrete tanks, or similar structures made of material with comparable attenuation characteristics. The purpose of the tank is to contain a substance. ( 19 ) The power limit applies inside a closed tank and corresponds to a spectral density of – 41,3 dBm/MHz e.i.r.p. outside a 500 litre test tank. ( 20 ) This category covers applications used to control the movement of models (principally miniature representations of vehicles) in the air, on land or over or under the water surface.’
Other acts of the same type
2009/585/EC: Commission Decision of 31 July 2009 amending Decision 2008/965/EC on financial aid from the Community for the year 2009 for certain Community reference laboratories in the field of animal health and live animals (Notified under document C(2009) 5947)2009/580/EC: Commission Decision of 29 July 2009 modifying Decision 2006/433/EC establishing the Community’s financial contribution to the expenditure incurred in the context of the emergency measures taken to combat classical swine fever in Germany in 2002 (notified under document number C(2009) 5866)2009/581/EC: Commission Decision of 29 July 2009 on a financial contribution from the Community towards emergency measures to combat avian influenza in Cloppenburg, Germany in December 2008 and January 2009 (notified under document number C(2009) 5869)Commission Decision of 28 July 2009 amending the list of herbal substances, preparations and combinations thereof for use in traditional herbal medicinal products (notified under document C(2009) 5804) (Text with EEA relevance)Council Decision 2009/569/CFSP of 27 July 2009 on support for OPCW activities in the framework of the implementation of the EU Strategy against Proliferation of Weapons of Mass Destruction2009/593/EC: Council Decision of 27 July 2009 amending Decision 1999/70/EC concerning the external auditors of the national central banks, as regards the external auditors of the Banka SlovenijeCouncil Decision 2009/597/CFSP of 27 July 2009 on the signing and provisional application of the Agreement between the European Union and the Republic of Croatia on the participation of the Republic of Croatia in the European Union military operation to contribute to the deterrence, prevention and repression of acts of piracy and armed robbery off the Somali coast (Operation Atalanta)2011/188/EC: Council Decision of 27 July 2009 on the conclusion by the European Community of the Interim Agreement between the European Community, the European Coal and Steel Community and the European Atomic Energy Community, of the one part, and Turkmenistan, of the other part, on trade and trade-related matters2009/614/EC: Commission Decision of 23 July 2009 amending Decision 2008/458/EC laying down rules for the implementation of Decision No 575/2007/EC of the European Parliament and of the Council establishing the European Return Fund for the period 2008 to 2013 as part of the general programme Solidarity and management of migration flows as regards Member States’ management and control systems, the rules for administrative and financial management and the eligibility of expenditure on projects co-financed by the Fund (Notified under document C(2009) 5453)2009/557/EC: Commission Decision of 22 July 2009 on a financial contribution from the Community towards emergency measures to combat swine vesicular disease in Italy in 2008 (notified under document number C(2009) 5608)Political and Security Committee Decision Atalanta/6/2009 of 22 July 2009 on the appointment of an EU Force Commander for the European Union military operation to contribute to the deterrence, prevention and repression of acts of piracy and armed robbery off the Somalia coast (Atalanta)2009/560/EC: Commission Decision of 22 July 2009 approving certain amended programmes for the eradication and monitoring of animal diseases and zoonoses for the year 2009 and amending Decision 2008/897/EC as regards the Community’s financial contribution to certain Member States for programmes approved by that Decision (notified under document number C(2009) 5475)
Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.
What to look at next
Browse all EU Legal ActsEvery instrument by type and year, full text free to read section by sectionEuropean Union legislationEU Legal Acts by type and yearGrouped by instrument type and year of enactment, so you can find others of the same kindBrowse by type and yearEuropean Union: what this database coversWhich datasets are here, which official source they come from, and how current they areEuropean Union overview