Packaging
Article 1
Open ↗For the purposes of this Regulation, ‘packaging’ means sales packaging and grouped packaging as defined in point 1 of Article 3 of Directive 94/62/EC of the European Parliament and of the Council ( 3 ) .
Source
Commission Implementing Regulation (EU) 2020/2151 of 17 December 2020 laying down rules on harmonised marking specifications on single-use plastic products listed in Part D of the Annex to Directive (EU) 2019/904 of the European Parliament and of the Council on the reduction of the impact of certain plastic products on the environment (Text with EEA relevance)
Commission Implementing Regulation (EU) 2020/2151 of 17 December 2020 laying down rules on harmonised marking specifications on single-use plastic products listed in Part D of the Annex to Directive (EU) 2019/904 of the European Parliament and of the Council on the reduction of the impact of certain plastic products on the environment (Text with EEA relevance)
Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗
Harmonised marking specifications
Article 2
Open ↗1. The harmonised marking specifications for sanitary towels (pads), and for tampons and tampon applicators are laid down in Annex I. 2. The harmonised marking specifications for wet wipes, i.e. pre-wetted personal care and domestic wipes are laid down in Annex II. 3. The harmonised marking specifications for tobacco products with filters and filters marketed for use in combination with tobacco products are laid down in Annex III. 4. The harmonised marking specifications for beverage cups are laid down in Annex IV.
Languages
Article 3
Open ↗The information text of the marking shall be written in the official language or languages of the Member State(s) where the single-use plastic product is placed on the market.
Entry into force and application
Article 4
Open ↗This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union . It shall apply from 3 July 2021.
Supplementary provisions
Harmonised marking specifications for sanitary towels (pads), and for tampons and tampon applicators
ANNEX ISupplementary provisions
Open ↗ANNEX I Harmonised marking specifications for sanitary towels (pads), and for tampons and tampon applicators 1. Packaging of sanitary towels (pads), with the surface area of 10 cm 2 or more, shall bear the following printed marking: Note : the black line bordering the marking is not part thereof. Its only purpose is to show the thin white line bordering the marking against the white page. By way of derogation from the first sentence of this point, the marking of packaging of sanitary towels (pads) placed on the market before 4 July 2022 may be affixed by means of stickers. 2. Packaging of tampons and tampon applicators, with the surface area of 10 cm 2 or more, shall bear the following printed marking: Note : the black line bordering the marking is not part thereof. Its only purpose is to show the thin white line bordering the marking against the white page. By way of derogation from the first sentence of this point, the marking of packaging of tampons and tampons applicators placed on the market before 4 July 2022 may be affixed by means of stickers. 3. The marking set out in points 1 and 2 shall comply with the requirements laid down in this point. (a) Position of the marking The marking shall be placed horizontally on the external front or top surface, whichever is more clearly visible, of the packaging. Where the marking of the minimum size cannot fit in its entirety on the external front or top surface of the packaging, it may be placed partly on two sides of the packaging, i.e. top and front, or front and side, whichever is more clearly visible. Where it is not possible to place the marking horizontally due to the shape or size of the packaging, it may be rotated 90° and placed vertically. The boxes of the marking shall not be separated. When opening the packaging in accordance with any instructions, the marking should not be torn or made illegible. (b) Size of the marking The marking shall be composed of two equal-sized red and blue boxes, which are placed next to each other, and a rectangular black box containing the information text ‘PLASTIC IN PRODUCT’, placed below the two equal-sized boxes. The ratio between the height and length of the marking shall be 1:2. Where the area of the external front or top surface of the packaging on which the marking is placed is less than 65 cm 2 , the minimum size of the marking shall be 1,4 cm by 2,8 cm (3,92 cm 2 ). In all other cases, the marking shall cover at least 6 % of the surface area on which it is placed. The maximum required size of the marking shall be 3 cm by 6 cm (18 cm 2 ). (c) Design of the marking The design of the marking shall be reproduced without adding any effects, adjusting the colours, retouching or extending the background. The marking shall be reproduced at a minimum resolution of 300 dots per inch when printed in actual size. The marking shall be bordered by a thin white line. The information text ‘PLASTIC IN PRODUCT’ shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt and a maximum of 14 pt. Where the information text is translated into another or several official languages of the Member States, the translated information text shall be placed either close below the marking, or inside the rectangular black box below the first language, and shall be in both cases clearly visible. In exceptional cases due to spatial constraints on the external front or top surface of the packaging, the information text translated into another or several official languages of the Member States may be placed elsewhere on the packaging as close as possible to the marking and where it is clearly visible. The translated information text shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt and a maximum of 14 pt. Where the information text in additional languages is placed in the rectangular black box, derogations from the maximum required size of the marking are possible. The colours having the following colour codes shall be used: — White: C = 0 / M = 0 / Y = 0 / K = 0 — Black: C = 0 / M = 0 / Y = 0 / K = 100 — Red: C = 0 / M = 90 / Y = 60 / K = 0 — Blue: C = 60 / M = 0 / Y = 0 / K = 0.
Harmonised marking specifications for wet wipes
ANNEX IISupplementary provisions
Open ↗ANNEX II Harmonised marking specifications for wet wipes 1. Packaging of wet wipes (i.e. pre-wetted personal care and domestic wipes), with the surface area of 10 cm 2 or more, shall bear the following printed marking: Note : the black line bordering the marking is not part thereof. Its only purpose is to show the thin white line bordering the marking against the white page. By way of derogation from the first sentence of this point, the marking of packaging of wet wipes placed on the market before 4 July 2022 may be affixed by means of stickers. 2. The marking shall comply with the requirements laid down in this point. (a) Position of the marking The marking shall be placed horizontally on the external front or top surface, whichever is more clearly visible, of the packaging. Where the marking of the minimum size cannot fit in its entirety on the external front or top surface of the packaging, it may be placed partly on two sides of the packaging, i.e. top and front, or front and side, whichever is more clearly visible. Where it is not possible to place the marking horizontally due to the shape or size of the packaging, it may be rotated 90° and placed vertically. The boxes of the marking shall not be separated. When opening the packaging in accordance with any instructions, the marking should not be torn or made illegible. (b) Size of the marking The marking shall be composed of two equal-sized red and blue boxes, which are placed next to each other, and a rectangular black box containing the information text ‘PLASTIC IN PRODUCT’ placed below the two equal-sized boxes. The ratio between the height and length of the marking shall be 1:2. Where the area of the external front or top surface of the packaging on which the marking is placed is less than 65 cm 2 , the minimum size of the marking shall be 1,4 cm by 2,8 cm (3,92 cm 2 ). In all other cases, the marking shall cover at least 6 % of the surface area on which it is placed. The maximum required size of the marking shall be 3 cm by 6 cm (18 cm 2 ). (c) Design of the marking The design of the marking shall be reproduced without adding any effects, adjusting the colours, retouching or extending the background. The marking shall be reproduced at a minimum resolution of 300 dots per inch when printed in actual size. The marking shall be bordered by a thin white line. The information text ‘PLASTIC IN PRODUCT’ shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt and a maximum of 14 pt. Where the information text is translated into another or several official languages of the Member States, the translated information text shall be placed either close below the marking, or inside the rectangular black box below the first language, and shall be in both cases clearly visible. In exceptional cases due to spatial constraints on the external front or top surface of the packaging, the information text translated into another or several official languages of the Member States may be placed elsewhere on the packaging as close as possible to the marking and where it is clearly visible. The translated information text shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt and a maximum of 14 pt. Where the information text in additional languages is placed in the rectangular black box, derogations from the maximum required size of the marking are possible. The colours having the following colour codes shall be used: — White: C = 0 / M = 0 / Y = 0 / K = 0 — Black: C = 0 / M = 0 / Y = 0 / K = 100 — Red: C = 0 / M = 90 / Y = 60 / K = 0 — Blue: C = 60 / M = 0 / Y = 0 / K = 0.
Harmonised marking specifications for tobacco products with filters and filters marketed for use in combination with tobacco products
ANNEX IIISupplementary provisions
Open ↗ANNEX III Harmonised marking specifications for tobacco products with filters and filters marketed for use in combination with tobacco products 1. Unit packet as defined in point 30 of Article 2 of Directive 2014/40/EU (‘unit packet’) and outside packaging as defined in point 29 of Article 2 of Directive 2014/40/EU (‘outside packaging’) for tobacco products with filters with the surface area of 10 cm 2 or more; and packaging for filters marketed for use in combination with tobacco products with the surface area of 10 cm 2 or more shall bear the following printed marking: Note : the black line bordering the marking is not part thereof. Its only purpose is to show the thin white line bordering the marking against the white page. By way of derogation from the first sentence of this point, the marking of unit packet and outside packaging for tobacco products with filters and packaging for filters marketed for use in combination with tobacco products placed on the market before 4 July 2022 may be affixed by means of stickers. 2. The marking shall comply with the requirements laid down in this point. (a) Position of the marking (i) Tobacco products with filters The marking shall be placed horizontally on the external back surface of the unit packet and on the outside packaging. Where the marking of the minimum size cannot fit horizontally on the external back surface of the unit packet, it may be rotated 90° and placed vertically on the back surface or on any of the external lateral surfaces of the unit packet. In all cases, it shall be clearly visible. The boxes of the marking shall not be separated. The marking shall not obstruct in any way the visibility of the health warnings required by Directive 2014/40/EU. The marking shall not be totally or partially covered by other labels or stamps. When opening the unit packet and of the outside packaging in accordance with any instructions, the marking should not be torn or made illegible. (ii) Filters marketed for use in combination with tobacco products The marking shall be placed horizontally on the external front or top surface, whichever is more clearly visible, of the packaging. Where the marking of the minimum size cannot fit in its entirety on the external front or top surface of the packaging, it may be placed horizontally partly on two sides of the packaging, i.e. top and front or front and side, whichever is more clearly visible. Where it is not possible to place the marking horizontally due to the shape or size of the packaging, it may be rotated 90° and placed vertically. The boxes of the marking shall not be separated. When opening of the packaging in accordance with any instructions, the marking should not be torn or made illegible. (b) Size of the marking The marking shall be composed of two equal-sized red and blue boxes, which are placed next to each other, and a rectangular black box containing the information text ‘PLASTIC IN FILTER’ placed below the two equal-sized boxes. The ratio between the height and length of the marking shall be 1:2. (i) Tobacco products with filters Where the area of the external back surface of the unit packet is less than 65 cm 2 , the minimum size of the marking shall be 1,4 cm by 2,8 cm (3,92 cm 2 ). In all other cases, the marking shall cover at least 6 % of the surface area on which it is placed. The maximum required size of the marking shall be 3 cm by 6 cm (18 cm 2 ). (ii) For filters marketed for use in combination with tobacco products Where the area of the external front or top surface of the packaging on which the marking is placed is less than 65 cm 2 , the minimum size of the marking shall be 1,4 cm by 2,8 cm (3,92 cm 2 ). In all other cases, the marking shall cover at least 6 % of the surface area on which it is placed. The maximum required size of the marking shall be 3 cm by 6 cm (18 cm 2 ). (c) Design of the marking The design of the marking shall be reproduced without adding any effects, adjusting the colours, retouching or extending the background. The marking shall be reproduced at a minimum resolution of 300 dots per inch when printed in actual size. The marking shall be bordered by a thin white line. The information text ‘PLASTIC IN FILTER’ shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt and a maximum of 14 pt. Where the information text is translated into another or several official languages of the Member States, the translated information text shall be placed either close below the marking, or inside the rectangular black box below the first language, and shall be in both cases clearly visible. In exceptional cases due to spatial constraints on the external front or top surface of the packaging, the information text translated into another or several official languages of the Member States may be placed elsewhere on the packaging as close as possible to the marking and where it is clearly visible. The translated information text shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt and a maximum of 14 pt. Where the information text in additional languages is placed in the rectangular black box, derogations from the maximum required size of the marking are possible. The colours having the following colour codes shall be used: — White: C = 0 / M = 0 / Y = 0 / K = 0 — Black: C = 0 / M = 0 / Y = 0 / K = 100 — Red: C = 0 / M = 90 / Y = 60 / K = 0 — Blue: C = 60 / M = 0 / Y = 0 / K = 0.
Harmonised marking specifications for beverage cups
ANNEX IVSupplementary provisions
Open ↗ANNEX IV Harmonised marking specifications for beverage cups 1. Beverage cups made partly from plastic shall bear the following printed marking: Note : the black line bordering the marking is not part thereof. Its only purpose is to show the thin white line bordering the marking against the white page. By way of derogation from the first sentence of this point, the marking of beverage cups made partly from plastic placed on the market before 4 July 2022 may be affixed by means of stickers. 2. Beverage cups made wholly from plastic shall bear either the following printed marking or the following engraved/embossed marking: Printed Note : the black line bordering the marking is not part thereof. Its only purpose is to provide contrast against the white page. By way of derogation from the first sentence of this point, the marking of beverage cups made wholly from plastic placed on the market before 4 July 2022 may be affixed by means of stickers. Engraved/embossed Note : the black line bordering the marking and grey background are not part thereof. Its only purpose is to provide contrast against the white page. 3. The marking for beverage cups made partly from plastic shall comply with the requirements laid down in this point. (a) Position of the marking (i) Traditional cups: The marking shall be placed horizontally on the external surface of the cup away from the rim to avoid contact with the consumer’s mouth when drinking. The marking shall not be placed under the base of the cup. (ii) Champagne-type cups: The marking shall be placed horizontally on the external surface of the cup, including the upper side of the base that holds the stem. The marking shall be placed away from the rim to avoid contact with the consumer’s mouth when drinking. The marking shall not be placed under the base of the cup. Where it is not possible to place the marking horizontally due to the shape or size of the cup, it may be rotated 90° and placed vertically. The boxes of the marking shall not be separated. (b) Size of the marking The marking shall be composed of two equal-sized red and blue boxes, which are placed next to each other, and a rectangular black box containing the information text ‘PLASTIC IN PRODUCT’ placed below the two equal-sized boxes. The ratio between the height and length of the marking shall be 1:2. For cups with a volume of less than 500 ml, the minimum size of the marking shall be 1,4 cm by 2,8 cm (3,92 cm 2 ). For cups with a volume of 500 ml or more, the minimum size of the marking shall be 1,6 cm by 3,2 cm (5,12 cm 2 ). (c) Design of the marking The design of the marking shall be reproduced without adding any effects, adjusting the colours, retouching or extending the background. The marking shall be reproduced at a minimum resolution of 300 dots per inch when printed in actual size. The marking shall be bordered by a thin white line. The information text ‘PLASTIC IN PRODUCT’ shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt for the cups of less than 500 ml and of 6 pt for the cups of 500 ml or more. Where the information text is translated into another or several official languages of the Member States, the translated information text shall be placed either close below the marking, or inside the rectangular black box below the first language, and shall be in both cases clearly visible. In exceptional cases due to spatial constraints on the external surface of the cup, the information text translated into another or several official languages of the Member States may be placed elsewhere on the cup as close as possible to the marking and where it is clearly visible. The translated information text shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt for the cups of less than 500 ml and 6 pt for the cups of 500 ml and more. Where the information text in additional languages is placed in the rectangular black box, derogations from the maximum required size of the marking are possible. The colours having the following colour codes shall be used: — White: C = 0 / M = 0 / Y = 0 / K = 0 — Black: C = 0 / M = 0 / Y = 0 / K = 100 — Red: C = 0 / M = 90 / Y = 60 / K = 0 — Blue: C = 60 / M = 0 / Y = 0 / K = 0. 4. The marking for beverage cups made wholly from plastic shall comply with the requirements laid down in this point (a) Position of the marking (i) Traditional cups The marking shall be placed horizontally on the external surface of the cup, wherever is more clearly visible. The marking shall not be placed under the base of the cup. When printed, the marking shall be placed away from the rim to avoid contact with the consumer’s mouth when drinking In the case of ridged cups, the marking shall not be embossed/engraved on the ridges. (ii) Champagne-type cups The marking shall be placed horizontally on the external surface of the cup, including the upper side of the base that holds the stem, wherever is more clearly visible. The marking shall not be placed under the base of the cup. When printed, the marking shall be placed away from the rim to avoid contact with the consumer’s mouth when drinking In the case of ridged cups, the marking shall not be embossed/engraved on the ridges. Where it is not possible to place the marking horizontally due to the shape or size of the cup, it may be rotated 90° and placed vertically. (b) Size of the marking The marking shall be rectangular-shaped and ratio between the height and length is 1:2. For cups with a volume of less than 500 ml, the minimum size of the marking shall be 1,4 cm by 2,8 cm (3,92 cm 2 ). For cups with a volume of 500 ml or more, the minimum size of the marking shall be 1,6 cm by 3,2 cm (5,12 cm 2 ). (c) Design of the marking (i) Printed: The design of the marking shall be reproduced in black ink without adding any effects, retouching or extending the background. The marking shall be reproduced at a minimum resolution of 300 dots per inch when printed in actual size. The marking should have sufficiently high contrast to the background to be highly readable. To this end, the outline of the marking should be printed in one of the following colours. — White: C = 0 / M = 0 / Y = 0 / K = 0 — Black: C = 0 / M = 0 / Y = 0 / K = 100 — Red: C = 0 / M = 90 / Y = 60 / K = 0 — Blue: C = 60 / M = 0 / Y = 0 / K = 0. (ii) Engraved/embossed: The design of the marking shall be reproduced without adding effects, retouching or extending the background. The white outline as shown in the marking under point 1.2 of this Annex represents the lines to be engraved or embossed on the cup. The information text ‘MADE OF PLASTIC’ shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt for the cups of less than 500 ml and of 6 pt for the cups of 500 ml or more. Where the information text is translated into another or several official languages of the Member States, the translated information text shall be placed either close below the marking, or inside the rectangular black box below the first language, and shall be in both cases clearly visible. In exceptional cases due to spatial constraints on the external surface of the cup, the information text translated into another or several official languages of the Member States may be placed elsewhere on the cup as close as possible to the marking and where it is clearly visible. The translated information text shall be in upper case and in Helvetica Bold font. The font size shall be a minimum of 5 pt for the cups of less than 500 ml and 6 pt for the cups of 500 ml and more. When printed, the colours having the following colour codes shall be used: — White: C = 0 / M = 0 / Y = 0 / K = 0 — Black: C = 0 / M = 0 / Y = 0 / K = 100.
Other acts of the same type
Commission Implementing Regulation (EU) 2017/764 of 2 May 2017 approving non-minor amendments to the specification for a name entered in the register of traditional specialities guaranteed (Ovčí hrudkový syr — salašnícky (TSG))Commission Implementing Regulation (EU) 2017/765 of 2 May 2017 approving non-minor amendments to the specification for a name entered in the register of traditional specialities guaranteed (Ovčí salašnícky údený syr (TSG))Commission Regulation (EU) 2017/752 of 28 April 2017 amending and correcting Regulation (EU) No 10/2011 on plastic materials and articles intended to come into contact with food (Text with EEA relevance. )Commission Implementing Regulation (EU) 2017/753 of 28 April 2017 renewing the approval of the active substance cyhalofop-butyl in accordance with Regulation (EC) No 1107/2009 of the European Parliament and of the Council concerning the placing of plant protection products on the market, and amending the Annex to Commission Implementing Regulation (EU) No 540/2011 (Text with EEA relevance. )Commission Implementing Regulation (EU) 2017/754 of 28 April 2017 opening and providing for the management of Union tariff quotas for certain agricultural and processed agricultural products originating in EcuadorCommission Implementing Regulation (EU) 2017/755 of 28 April 2017 renewing the approval of the active substance mesosulfuron in accordance with Regulation (EC) No 1107/2009 of the European Parliament and of the Council concerning the placing of plant protection products on the market, and amending the Annex to Commission Implementing Regulation (EU) No 540/2011 (Text with EEA relevance. )Commission Implementing Regulation (EU) 2017/736 of 26 April 2017 amending Annex VIII to Regulation (EC) No 999/2001 of the European Parliament and of the Council as regards the approval of Slovenia's national control programme for classical scrapie (Text with EEA relevance. )Commission Implementing Regulation (EU) 2017/739 of 26 April 2017 amending Regulation (EC) No 1484/95 as regards fixing representative prices in the poultrymeat and egg sectors and for egg albuminCommission Implementing Regulation (EU) 2017/791 of 26 April 2017 entering a name in the register of protected designations of origin and protected geographical indications (Stupavské Zelé (PDO))Council Regulation (EU) 2017/762 of 25 April 2017 amending Regulation (EU) No 479/2013 on the waiver from the requirement to submit entry and exit summary declarations for Union goods that are moved across the Neum corridorCommission Implementing Regulation (EU) 2017/725 of 24 April 2017 renewing the approval of the active substance mesotrione in accordance with Regulation (EC) No 1107/2009 of the European Parliament and of the Council concerning the placing of plant protection products on the market, and amending the Annex to Commission Implementing Regulation (EU) No 540/2011 (Text with EEA relevance. )Commission Regulation (EU) 2017/712 of 20 April 2017 establishing the reference year and the programme of the statistical data and metadata for population and housing censuses provided for by Regulation (EC) No 763/2008 of the European Parliament and of the Council (Text with EEA relevance. )
Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.
What to look at next
Browse all EU Legal ActsEvery instrument by type and year, full text free to read section by sectionEuropean Union legislationEU Legal Acts by type and yearGrouped by instrument type and year of enactment, so you can find others of the same kindBrowse by type and yearEuropean Union: what this database coversWhich datasets are here, which official source they come from, and how current they areEuropean Union overview