LawPlayer
My bookmarksSign up freeSign up free
Source

Commission Implementing Regulation (EU) 2021/535 CHAPTER III — EU VEHICLE TYPE-APPROVAL WITH REGARD TO CERTAIN SPECIFIC CONSTRUCTION AND SAFETY REQUIREMENTS

Article 5–Article 6 · 2 articles

Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗

Application for the EU type-approval of a vehicle type as regards certain vehicle systems

Article 5

Open ↗

1.   A separate application for EU type-approval of a vehicle type as regards each of the following items shall be submitted to the type-approval authority by manufacturers or their representatives, using the respective model information document in accordance with Article 24(1)(a) of Regulation (EU) 2018/858: (a) the lay-out and the location of the statutory plate and the composition and the location of the vehicle identification number, using the model containing the information listed in Part 1 of Annex II; (b) the space for mounting and fixing of front and rear registration plates, using the model containing the information listed in Part 1 of Annex III; (c) the windscreen wiper and washer systems, using the model containing the information listed in Annex IV, Part 1, Section A; (d) the wheel guards, using the model containing the information listed in Part 1 of Annex V; (e) the windscreen defrosting and demisting systems, using the model containing the information listed in Part 1 of Annex VI; (f) the towing devices, using the model containing the information listed in Part 1 of Annex VII; (g) the spray suppression system, using the model containing the information listed in Annex VIII, Part 1, Section A; (h) the gear shift indicator, using the model containing the information listed in Part 1 of Annex IX; (i) the vehicle access, using the model containing the information listed in Part 1 of Annex X; (j) the reversing motion, using the model containing the information listed in Part 1 of Annex XI; (k) the vehicle masses and dimensions, using the model containing the information listed in Annex XIII, Part 1, Section A; (l) in case of hydrogen-powered vehicles, the vehicle fuel system of which incorporates liquefied hydrogen storage system (LHSS) or compressed hydrogen storage system (CHSS), using the model containing the information listed in Annex XIV, Part 1, Section A. 2.   The application for the EU type-approval of a type of vehicle as regard the gear shift indicator referred to in point (h) of paragraph 1 shall be submitted together with a declaration of the manufacturer that the vehicle complies with the relevant technical specifications set out in this Regulation and a certificate drawn up in accordance with the model set out in the Appendix to Part 1 of Annex IX. 3.   The manufacturer shall, when requested by the approval authority or the technical service, make available, for test purposes, a vehicle representative of the type to be approved.

Granting the EU type-approval of a vehicle type as regards certain vehicle systems

Article 6

Open ↗

1.   Where the technical specifications set out in Part 2 of Annexes II to XIII and in Annex XIV, Part 2, Sections D and E with regard to the respective requirements listed in Annex II to Regulation (EU) 2019/2144 are met, the type-approval authority shall grant an EU type-approval and issue a type-approval certificate number in accordance with the method set out in Annex IV of Commission Implementing Regulation (EU) 2020/683. 2.   The EU type-approval certificate, referred to in Article 28(1) of Regulation (EU) 2018/858, shall be drawn up in accordance with: (a) Part 3 of Annex II for the item referred to in point (a) of Article 5(1); (b) Part 3 of Annex III for the item referred to in point (b) of Article 5(1); (c) Annex IV, Part 3, Section A for the item referred to in point (c) of Article 5(1); (d) Part 3 of Annex V for the item referred to in point (d) of Article 5(1); (e) Part 3 of Annex VI for the item referred to in point (e) of Article 5(1); (f) Part 3 of Annex VII for the item referred to in point (f) of Article 5(1); (g) Annex VIII, Part 3, Section A for the item referred to in point (g) of Article 5(1); (h) Part 3 of Annex IX for the item referred to in point (h) of Article 5(1); (i) Part 3 of Annex X for the item referred to in point (i) of Article 5(1); (j) Part 3 of Annex XI for the item referred to in point (j) of Article 5(1); (k) Annex XIII, Part 3, Section A for the item referred to in point (k) of Article 5(1); and (l) Annex XIV, Part 3, Section A for the item referred to in point (l) of Article 5(1). 3.   In accordance with the second subparagraph of Article 6(5) of Regulation (EU) 2018/858, an EU type-approval may be granted for vehicles exceeding the maximum authorised dimensions set out in point 1.1. of Sections B, C and D of Part 2 of Annex XIII to this Regulation, in which case the remark ‘maximum authorised dimensions derogation’ shall be included in point 52 of the type-approval certificate and the certificate of conformity. 4.   An EU type-approval may be granted for vehicles intended for the transport of indivisible loads, the dimensions of which exceed the maximum authorised dimensions set out in point 1.1. of Sections B, C and D of Part 2 of Annex XIII to this Regulation, in which case the type-approval certificate and the certificate of conformity shall clearly indicate that the vehicle is intended for the transport of indivisible loads only.

Back to Commission Implementing Regulation (EU) 2021/535 — full text

Articles on this page are reproduced verbatim from official open data. See the attribution line.

Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.

What to look at next