Commission Implementing Decision (EU) 2022/180 of 8 February 2022 amending Decision 2006/771/EC as regards the update of harmonised technical conditions in the area of radio spectrum use for short-range devices (notified under document C(2022) 644) (Text with EEA relevance)

Member States shall report to the Commission on the implementation of this Decision by 1 October 2022 at the latest.’;

Article 1

Decision 2006/771/EC is amended as follows: (1) the following Article 4a is inserted: ‘Article 4a Member States shall report to the Commission on the implementation of this Decision by 1 October 2022 at the latest.’; (2) the Annex is replaced by the text set out in the Annex to this Decision.

Article 2

This Decision is addressed to the Member States.

ANNEXSupplementary provisions

ANNEX ‘ANNEX Frequency bands with corresponding harmonised technical conditions and implementation deadlines for short-range devices Table 1 defines the scope of different categories of short-range devices (defined in Article 2(3)) to which this Decision applies. Table 2 specifies different combinations of frequency band and category of short-range devices, and the harmonised technical conditions for spectrum access and implementation deadlines applicable thereto. General technical conditions applicable to all bands and short-range devices that fall within the scope of this Decision: — Member States shall allow adjacent frequency bands set out in Table 2 to be used as a single frequency band provided the specific conditions of each of these adjacent frequency bands are met. — Member States shall allow the usage of spectrum up to the transmit power, field strength or power density set out in Table 2. Pursuant to Article 3(3), they may impose less restrictive conditions, that is to say allow the use of spectrum with higher transmit power, field strength or power density, provided it does not reduce or compromise the appropriate coexistence between short-range devices in bands harmonised by this Decision. — Member States may only impose the additional parameters (channelling and/or channel access and occupation rules) set out in Table 2, and shall not add other parameters or spectrum access and mitigation requirements. Less restrictive conditions pursuant to Article 3(3), means that Member States may completely omit these additional parameters in a given cell or allow higher values, provided that the appropriate sharing environment in the harmonised band is not compromised. — Member States may only impose the other usage restrictions set out in Table 2 and shall not add additional usage restrictions. Since less restrictive conditions may be applied pursuant to Article 3(3), Member States may omit one or all of these restrictions, provided that the appropriate sharing environment in the harmonised band is not compromised. — Less restrictive conditions pursuant to Article 3(3) shall apply without prejudice to Directive 2014/53/EU. For the purposes of this Annex, the following duty cycle definition applies: ‘ duty cycle ’ means the ratio, expressed as a percentage, of Σ(Ton)/(Tobs) where Ton is the ‘on’ time of a single transmitter device and Tobs is the observation period. Ton is measured in an observation frequency band (Fobs). Unless otherwise specified in this technical annex, Tobs is a continuous one hour period and Fobs is the applicable frequency band in this technical annex. Less restrictive conditions within the meaning of Article 3(3), mean that Member States may allow a higher value for ‘duty cycle’. Table 1 Categories of short-range devices pursuant to Article 2(3) and their scope Category of short-range devices Scope Non-specific short-range devices (SRDs) Covers all kinds of radio devices, regardless of the application or their purpose, which fulfil the technical conditions as specified for a given frequency band. Typical uses include telemetry, telecommand, alarms, data transmissions in general and other applications. Active medical implant devices Covers the radio part of active implantable medical devices that are intended to be fully or partially introduced, surgically or medically, into the human body or that of an animal, and where applicable their peripherals. Active implantable medical devices are defined in Council Directive 90/385/EEC  ( 1 ) . Assistive listening devices (ALDs) Covers radio communications systems that allow persons with hearing impairment to increase their listening capability. Typical system installations include one or more radio transmitters and one or more radio receivers. High duty cycle/continuous transmission devices Covers radio devices that rely on low latency and high duty cycle transmissions. These devices are typically used for personal wireless audio and multimedia streaming systems used for combined audio/video transmissions and audio/video sync signals, mobile phones, automotive or home entertainment system, wireless microphones, cordless loudspeakers, cordless headphones, radio devices carried on a person, assistive listening devices, in-ear monitoring, wireless microphones for use at concerts or other stage productions, and low power analogue FM transmitters. Inductive devices Covers radio devices that use magnetic fields with inductive loop systems for near field communications and determination applications. This typically includes devices for car immobilisation, animal identification, alarm systems, cable detection, waste management, personal identification, wireless voice links, access control, proximity and metal sensors, anti-theft systems as well as RF anti-theft induction systems, data transfer to hand-held devices, automatic article identification, wireless control systems and automatic road tolling. Low duty cycle/high reliability devices Covers radio devices that rely on low overall spectrum utilisation and low duty cycle spectrum access rules to ensure highly reliable spectrum access and transmissions in shared bands. Typical applications include alarm systems that use radio communication for indicating an alert condition at a distant location and social alarm systems that allow reliable communication for a person in distress. Medical data acquisition devices Covers the transmission of non-voice data to and from non-implantable medical devices in order to monitor, diagnose and treat patients in healthcare facilities or in their homes as prescribed by duly authorised healthcare professionals. PMR446 devices Covers hand portable equipment (without base station or repeater use) carried on a person or manually operated, which uses integral antennas only in order to maximise sharing and minimise interference. PMR 446 equipment operates in short-range peer-to-peer mode and shall not be used as a part of infrastructure network nor as a repeater. Radio determination devices Covers radio devices used for determining the position, velocity and/or other characteristics of an object, or for obtaining information relating to these parameters. Radio determination equipment typically conducts measurements to obtain such characteristics. Radio determination devices exclude any kind of point-to-point or point-to-multipoint radio communications. Radio frequency identification (RFID) devices Covers tag/interrogator based radio communications systems, consisting of (i) radio devices (tags) attached to animate or inanimate items and (ii) transmitter/receiver units (interrogators) which activate the tags and receive data back. Typical applications include the tracking and identification of items, for instance for the purpose of electronic article surveillance (EAS), and collecting and transmitting data relating to the items to which tags are attached, which may be either battery-less, battery assisted or battery powered. The responses from a tag are validated by its interrogator and passed to its host system. Transport and traffic telematics devices Covers radio devices that are used in the fields of transport (road, rail, water or air, depending on the relevant technical restrictions), traffic management, navigation, mobility management and in intelligent transport systems (ITS). Typical applications include interfaces between different modes of transport, communication between vehicles (e.g. car to car), between vehicles and fixed locations (e.g. car to infrastructure) as well as communication from and to users. Wideband data transmission devices Covers radio devices that use wideband modulation techniques to access the spectrum. Typical uses include wireless access systems such as radio local area networks (WAS/RLANs) or wideband SRDs in data networks. Table 2 Frequency bands with corresponding harmonised technical conditions and implementation deadlines for short-range devices Band no Frequency band Category of short-range devices Transmit power limit/field strength limit/power density limit Additional parameters (channelling and/or channel access and occupation rules) Other usage restrictions Implemen-tation deadline 1 9-59,750 kHz Inductive devices 72 dΒμΑ/m at 10 metres     1 July 2014 90 9-148 kHz Radio determination devices 46 dBμA/m at 10 m distance at a reference of 100 Hz, outside the Nuclear Magnetic Resonance (NMR) device. Magnetic field strength descending 10 dB/decade above 100Hz.   For enclosed Nuclear Magnetic Resonance (NMR) applications [j]. 1 July 2022 2 9-315 kHz Active medical implant devices 30 dΒμΑ/m at 10 metres Duty cycle limit: 10 % This set of usage conditions is only available to active implantable medical devices. 1 July 2014 3 59,750-60,250 kHz Inductive devices 42 dΒμΑ/m at 10 metres     1 July 2014 4 60,250-74,750 kHz Inductive devices 72 dBμA/m at 10 metres     1 July 2014 5 74,750-75,250 kHz Inductive devices 42 dBμA/m at 10 metres     1 July 2014 6 75,250-77,250 kHz Inductive devices 72 dBμA/m at 10 metres     1 July 2014 7 77,250-77,750 kHz Inductive devices 42 dBμA/m at 10 metres     1 July 2014 8 77,750-90 kHz Inductive devices 72 dBμA/m at 10 metres     1 July 2014 9 90-119 kHz Inductive devices 42 dBμA/m at 10 metres     1 July 2014 10 119-128,6 kHz Inductive devices 66 dBμA/m at 10 metres     1 July 2014 11 128,6-129,6 kHz Inductive devices 42 dBμA/m at 10 metres     1 July 2014 12 129,6-135 kHz Inductive devices 66 dBμA/m at 10 metres     1 July 2014 13 135-140 kHz Inductive devices 42 dBμA/m at 10 metres     1 July 2014 14 140-148,5 kHz Inductive devices 37,7 dΒμΑ/m at 10 metres     1 July 2014 15 148,5-5 000 kHz [1] Inductive devices -15 dΒμΑ/m at 10 metres in any bandwidth of 10 kHz. Furthermore the total field strength is -5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz     1 July 2014 91 148-5 000 kHz Radio determination devices -15 dBμA/m at 10 m distance outside the Nuclear Magnetic Resonance (NMR) device.   For enclosed Nuclear Magnetic Resonance (NMR) applications [j]. 1 July 2022 17 400-600 kHz Radio Frequency Identification (RFID) devices -8 dΒμΑ/m at 10 metres     1 July 2014 85 442,2-450,0 kHz Non-specific short-range devices 7 dBμA/m at 10 m Channel spacing ≥ 150 Hz This set of usage conditions is only available for person detection and collision avoidance devices. 1 January 2020 18 456,9-457,1 kHz Non-specific short-range devices 7 dBμA/m at 10 m   This set of usage conditions is only available for emergency detections of buried victims and valuable items devices. 1 July 2014 19 984-7 484 kHz Transport and Traffic Telematics devices 9 dΒμΑ/m at 10 m Duty cycle limit: 1 % This set of usage conditions is only available for Eurobalise transmissions in the presence of trains using the 27 090 -27 100 kHz band for telepowering pursuant to the conditions set for band 28. 1 July 2014 20 3 155 -3 400 kHz Inductive devices 13,5 dΒμΑ/m at 10 metres     1 July 2014 21 5 000 -30 000 kHz [2] Inductive devices -20 dΒμΑ/m at 10 metres in any bandwidth of 10 kHz. Furthermore the total field strength is -5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz     1 July 2014 92 5 000 -30 000 kHz Radio determination devices -5 dBμA/m at 10m distance outside the Nuclear Magnetic Resonance (NMR) device.   For enclosed Nuclear Magnetic Resonance (NMR) applications [j]. 1 July 2022 22 6 765 -6 795 kHz Inductive devices 42 dΒμΑ/m at 10 metres     1 July 2014 23 7 300 -23 000 kHz Transport and Traffic Telematics devices -7 dΒμΑ/m at 10 m Antenna requirements apply [8]. This set of usage conditions is only available for Eurobalise transmissions in the presence of trains using the 27 090 -27 100 kHz band for telepowering pursuant to the conditions set for band 28. 1 July 2014 24 7 400 -8 800 kHz Inductive devices 9 dΒμΑ/m at 10 metres     1 July 2014 25 10 200 -11 000 kHz Inductive devices 9 dΒμΑ/m at 10 metres     1 July 2014 27a 13 553 -13 567 kHz Inductive devices 42 dΒμΑ/m at 10 metres Transmission mask and antenna requirements for all combined frequency segments apply [8], [9].   1 January 2020 27b 13 553 -13 567 kHz Radio Frequency Identification (RFID) devices 60 dΒμΑ/m at 10 metres Transmission mask and antenna requirements for all combined frequency segments apply [8], [9].   1 July 2014 27c 13 553 -13 567 kHz Non-specific short-range devices 10 mW e.r.p.     1 July 2014 28 26 957 -27 283 kHz Non-specific short-range devices 10 mW e.r.p.     1 July 2014 29 26 990 -27 000 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 %. Model control devices [d] may operate without duty cycle restrictions.   1 July 2014 30 27 040 -27 050 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 %. Model control devices [d] may operate without duty cycle restrictions.   1 July 2014 31 27 090 -27 100 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 %. Model control devices [d] may operate without duty cycle restrictions.   1 July 2014 32 27 140 -27 150 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 %. Model control devices [d] may operate without duty cycle restrictions.   1 July 2014 33 27 190 -27 200 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 %. Model control devices [d] may operate without duty cycle restrictions.   1 July 2014 34 30-37,5 MHz Active medical implant devices 1 mW e.r.p. Duty cycle limit: 10 % This set of usage conditions is only available to ultra-low power medical membrane implants for blood pressure measurements within the definition of active implantable medical devices. 1 July 2014 93 30-130 MHz Radio determination devices -36 dBm e.r.p. outside the Nuclear Magnetic Resonance (NMR) device.   For enclosed Nuclear Magnetic Resonance (NMR) applications [j]. 1 July 2022 35 40,66-40,7 MHz Non-specific short-range devices 10 mW e.r.p.     1 January 2018 36 87,5-108 MHz High duty cycle/continuous transmission devices 50 nW e.r.p. Channel spacing up to 200 kHz. This set of usage conditions is only available to wireless audio and multimedia streaming transmitters with analogue frequency modulation (FM). 1 July 2014 37a 169,4-169,475 MHz Assistive Listening Devices (ALD) 500 mW e.r.p. Channel spacing: max 50 kHz.   1 July 2014 37c 169,4-169,475 MHz Non-specific short-range devices 500 mW e.r.p. Channel spacing: max 50 kHz. Duty cycle limit: 1,0 %. For metering devices [a], the duty cycle limit is 10,0 %   1 July 2014 38 169,4-169,4875 MHz Non-specific short-range devices 10 mW e.r.p. Duty cycle limit: 0,1 %.   1 January 2020 39a 169,4875-169,5875 MHz Assistive Listening Devices (ALD) 500 mW e.r.p. Channel spacing: max 50 kHz.   1 July 2014 39b 169,4875-169,5875 MHz Non-specific short-range devices 10 mW e.r.p. Duty cycle limit: 0,001 %. Between 00:00h and 06:00h local time a duty cycle limit of 0,1 % may be used.   1 January 2020 40 169,5875-169,8125 MHz Non-specific short-range devices 10 mW e.r.p. Duty cycle limit: 0,1 %.   1 January 2020 82 173,965-216 MHz Assistive Listening Devices (ALD) 10 mW e.r.p. On a tuning range basis [5]. Channel spacing: max 50 kHz. A threshold of 35 dBμV/m is required to ensure the protection of a DAB receiver located at 1,5 m from the ALD device, subject to DAB signal strength measurements taken around the ALD operating site. The ALD device should operate under all circumstances at least 300 kHz away from the channel edge of an occupied DAB channel. Requirements on techniques to access spectrum and mitigate interference apply [7].   1 January 2018 41 401-402 MHz Active medical implant devices 25 μW e.r.p. Channel spacing: 25 kHz. Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz. Requirements on techniques to access spectrum and mitigate interference apply [7]. Alternatively, a duty cycle limit of 0,1 % may also be used. This set of usage conditions is only available for systems specifically designed for the purpose of providing non-voice digital communications between active implantable medical devices and/or body-worn devices and other devices external to the human body used for transferring non-time critical individual patient-related physiological information. 1 July 2014 42 402-405 MHz Active medical implant devices 25 μW e.r.p. Channel spacing: 25 kHz. Individual transmitters may combine adjacent channels for increased bandwidth up to 300 kHz. Other techniques to access spectrum or mitigate interference, including bandwidths greater than 300 kHz, can be used provided they ensure compatible operation with the other users and in particular with meteorological radiosondes [7]. This set of usage conditions is only available to active implantable medical devices. 1 July 2014 43 405-406 MHz Active medical implant devices 25 μW e.r.p. Channel spacing: 25 kHz Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz. Requirements on techniques to access spectrum and mitigate interference apply [7]. Alternatively a duty cycle limit of 0,1 % may also be used. This set of usage conditions is only available for systems specifically designed for the purpose of providing non-voice digital communications between active implantable medical devices and/or body-worn devices and other devices external to the human body used for transferring non-time critical individual patient-related physiological information. 1 July 2014 86 430-440 MHz Medical data acquisition devices -50 dBm/100kHz e.r.p. power density but not exceeding a total power of -40 dBm/10MHz (both limits are intended for measurement outside of the patient’s body)   The set of usage conditions is only available for Ultra-Low Power Wireless Medical Capsule Endoscopy (ULP-WMCE) applications [h]. 1 January 2020 44a 433,05-434,79 MHz Non-specific short-range devices 1 mW e.r.p. and -13 dBm/10 kHz power density for bandwidth modulation larger than 250 kHz   Voice applications are allowed with advanced mitigation techniques. Other audio and video applications are excluded. 1 July 2014 44b 433,05-434,79 MHz Non-specific short-range devices 10 mW e.r.p. Duty cycle limit: 10 %   1 January 2020 45c 434,04-434,79 MHz Non-specific short-range devices 10 mW e.r.p. Duty cycle limit: 100 % subject to channel spacing up to 25 kHz. Voice applications are allowed with advanced mitigation techniques. Other audio and video applications are excluded. 1 January 2020 83 446,0-446,2 MHz PMR446 500 mW e.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7].   1 January 2018 87 862-863 MHz Non-specific short-range devices 25 mW e.r.p. Duty cycle limit: 0,1 %. Bandwidth: ≤ 350 kHz.   1 January 2020 46a 863-865 MHz Non-specific short-range devices 25 mW e.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Alternatively, a duty cycle limit of 0,1 % may also be used.   1 January 2018 46b 863-865 MHz High duty cycle/continuous transmission devices 10 mW e.r.p.   This set of usage conditions is only available to wireless audio and multimedia streaming devices. 1 July 2014 84 863-868 MHz Wideband data transmission devices 25 mW e.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Bandwidth: > 600 kHz and ≤ 1 MHz. Duty cycle: ≤ 10 % for network access points [g] Duty cycle: ≤ 2,8 % otherwise This set of usage conditions is only available for wideband SRDs in data networks [g]. 1 January 2018 47 865-868 MHz Non-specific short-range devices 25 mW e.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Alternatively, a duty cycle limit of 1 % may also be used.   1 January 2020 47a 865-868 MHz [6] Radio Frequency Identification (RFID) devices 2 W e.r.p. Interrogator transmissions at 2 W e.r.p. only permitted within the four channels centred at 865,7 MHz, 866,3 MHz, 866,9 MHz and 867,5 MHz RFID interrogator devices placed on the market before the repeal date of EC Decision 2006/804/EC are ‘grandfathered’, i.e. they are continuously permitted to be used in line with the provisions set out in EC Decision 2006/804/EC before the repeal date. Requirements on techniques to access spectrum and mitigate interference apply [7]. Bandwidth ≤ 200 kHz   1 January 2018 47b 865-868 MHz Non-specific short-range devices 500 mW e.r.p. Transmissions only permitted within the frequency ranges 865,6-865,8 MHz, 866,2-866,4 MHz, 866,8-867,0 MHz and 867,4-867,6 MHz. Adaptive Power Control (APC) required. Alternatively other mitigation technique with at least an equivalent level of spectrum compatibility. Requirements on techniques to access spectrum and mitigate interference apply [7]. Bandwidth: ≤ 200 kHz Duty cycle: ≤ 10 % for network access points [g] Duty cycle: ≤ 2,5 % otherwise This set of usage conditions is only available for data networks [g]. 1 January 2018 48 868-868,6 MHz Non-specific short-range devices 25 mW e.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Alternatively, a duty cycle limit of 1 % may also be used.   1 January 2020 49 868,6-868,7 MHz Low duty cycle/high reliability devices 10 mW e.r.p. Channel spacing: 25 kHz. The whole frequency band may also be used as a single channel for high-speed data transmission. Duty cycle limit: 1,0 % This set of usage conditions is only available to alarm systems [e]. 1 July 2014 50 868,7-869,2 MHz Non-specific short-range devices 25 mW e.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Alternatively a duty cycle limit of 0,1 % may also be used.   1 January 2020 51 869,2-869,25 MHz Low duty cycle/high reliability devices 10 mW e.r.p. Channel spacing: 25 kHz. Duty cycle limit: 0,1 % This set of usage conditions is only available to social alarm devices [b]. 1 July 2014 52 869,25-869,3 MHz Low duty cycle/high reliability devices 10 mW e.r.p. Channel spacing: 25 kHz. Duty cycle limit: 0,1 % This set of usage conditions is only available to alarm systems [e]. 1 July 2014 53 869,3-869,4 MHz Low duty cycle/high reliability devices 10 mW e.r.p. Channel spacing: 25 kHz. Duty cycle limit: 1,0 % This set of usage conditions is only available to alarm systems [e]. 1 July 2014 54 869,4-869,65 MHz Non-specific short-range devices 500 mW e.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Alternatively, a Duty cycle limit of 10 % may also be used.   1 January 2020 55 869,65-869,7 MHz Low duty cycle/high reliability devices 25 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit: 10 % This set of usage conditions is only available to alarm systems [e]. 1 July 2014 56a 869,7-870 MHz Non-specific short-range devices 5 mW e.r.p.   Voice applications are allowed with advanced mitigation techniques. Other audio and video applications are excluded. 1 July 2014 56b 869,7-870 MHz Non-specific short-range devices 25 mW e.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Alternatively, a duty cycle limit of 1 % may also be used.   1 January 2020 57a 2 400 -2 483,5 MHz Non-specific short-range devices 10 mW equivalent isotropic radiated power (e.i.r.p.)     1 July 2014 57b 2 400 -2 483,5 MHz Radio determination devices 25 mW e.i.r.p.     1 July 2014 57c 2 400 -2 483,5 MHz Wideband data transmission devices 100 mW e.i.r.p. and 100 mW/100 kHz e.i.r.p. density applies when frequency hopping modulation is used, 10 mW/MHz e.i.r.p. density applies when other types of modulation are used Requirements on techniques to access spectrum and mitigate interference apply [7].   1 July 2014 58 2 446 -2 454 MHz Radio Frequency Identification (RFID) devices 500 mW e.i.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7].   1 July 2014 59 2 483,5 -2 500 MHz Active medical implant devices 10 mW e.i.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Channel spacing: 1 MHz. The whole frequency band may also be used dynamically as a single channel for high-speed data transmissions. In addition, a duty cycle limit of 10 % applies. This set of usage conditions is only available to active implantable medical devices. Peripheral master units are for indoor use only. 1 July 2014 59a 2 483,5 -2 500 MHz Medical data acquisition devices 1 mW e.i.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Modulation Bandwidth: ≤ 3 MHz. In addition, a duty cycle: ≤ 10 % applies. The set of usage conditions is only available for medical body area network system (MBANS) [f] for indoor use within healthcare facilities 1 January 2018 59b 2 483,5 -2 500 MHz Medical data acquisition devices 10 mW e.i.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. Modulation Bandwidth: ≤ 3 MHz. In addition, a duty cycle: ≤ 2 % applies The set of usage conditions is only available for medical body area network system (MBANS) [f] for indoor use within the patient’s home 1 January 2018 60 4 500 -7 000 MHz Radio determination devices 24 dBm e.i.r.p. [3] Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to Tank Level Probing Radar [c]. 1 July 2014 61 5 725 -5 875 MHz Non-specific short-range devices 25 mW e.i.r.p.     1 July 2014 62 5 795 -5 815 MHz Transport and Traffic Telematics devices 2 W e.i.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions applies only to road tolling applications and smart tachograph, weight and dimension applications [i]. 1 January 2020 88 5 855 -5 865 MHz Transport and Traffic Telematics devices 33 dBm e.i.r.p., 23 dBm/MHz e.i.r.p. density and a Transmit Power Control (TPC) range of 30 dB Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to vehicle-to-vehicle, vehicle-to-infrastructure and infrastructure-to-vehicle systems. 1 January 2020 89 5 865 -5 875 MHz Transport and Traffic Telematics devices 33 dBm e.i.r.p., 23 dBm/MHz e.i.r.p. density and a Transmit Power Control (TPC) range of 30 dB Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to vehicle-to-vehicle, vehicle-to-infrastructure and infrastructure-to-vehicle systems. 1 January 2020 63 6 000 -8 500 MHz Radio determination devices 7 dBm/50 MHz peak e.i.r.p. and -33 dBm/MHz mean e.i.r.p. Automatic power control and antenna requirements as well as requirements on techniques to access spectrum and mitigate interference apply [7], [8] [10]. This set of usage conditions is only available to Level Probing Radar. Established exclusion zones around radio astronomy sites shall be obeyed. 1 July 2014 64 8 500 -10 600 MHz Radio determination devices 30 dBm e.i.r.p. [3] Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to Tank Level Probing Radar [c]. 1 July 2014 65 17,1-17,3 GHz Radio determination devices 26 dBm e.i.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to ground-based systems. 1 July 2014 66 24,05-24,075 GHz Transport and Traffic Telematics devices 100 mW e.i.r.p.     1 July 2014 67 24,05-26,5 GHz Radio determination devices 26 dBm/50 MHz peak e.i.r.p. and -14 dBm/MHz mean e.i.r.p. Automatic power control and antenna requirements as well as requirements on techniques to access spectrum and mitigate interference apply [7]. [8], [10] This set of usage conditions is only available to Level Probing Radar. Established exclusion zones around radio astronomy sites shall be obeyed. 1 July 2014 68 24,05-27 GHz Radio determination devices 43 dBm e.i.r.p. [3] Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to Tank Level Probing Radar [c]. 1 July 2014 69a 24,075-24,15 GHz Transport and Traffic Telematics devices 100 mW e.i.r.p. Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to ground-based vehicle radars. 1 July 2014 69b 24,075-24,15 GHz Transport and Traffic Telematics devices 0,1 mW e.i.r.p.     1 July 2014 70a 24,15-24,25 GHz Non-specific short-range devices 100 mW e.i.r.p.     1 July 2014 70b 24,15-24,25 GHz Transport and Traffic Telematics devices 100 mW e.i.r.p.     1 July 2014 74a 57-64 GHz Non-specific short-range devices 100 mW e.i.r.p. and a maximum transmit power of 10 dBm     1 January 2020 74b 57-64 GHz Radio determination devices 43 dBm e.i.r.p. [3] Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to Tank Level Probing Radar [c]. 1 July 2014 74c 57-64 GHz Radio determination devices 35 dBm/50 MHz peak e.i.r.p. and -2 dBm/MHz mean e.i.r.p. Automatic power control and antenna requirements as well as requirements on techniques to access spectrum and mitigate interference apply [7] [8], [10]. This set of usage conditions is only available to Level Probing Radar. 1 July 2014 75 57-71 GHz Wideband data transmission devices 40 dBm e.i.r.p. and 23 dBm/MHz e.i.r.p. density Requirements on techniques to access spectrum and mitigate interference apply [7]. Fixed outdoor installations are excluded. 1 January 2020 75a 57-71 GHz Wideband data transmission devices 40 dBm e.i.r.p., 23 dBm/MHz e.i.r.p. density and maximum transmit power of 27 dBm at the antenna port or ports Requirements on techniques to access spectrum and mitigate interference apply [7].   1 January 2020 75b 57-71 GHz Wideband data transmission devices 55 dBm e.i.r.p., 38 dBm/MHz e.i.r.p. density and a transmit antenna gain ≥ 30 dBi Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to fixed outdoor installations. 1 January 2020 76 61-61,5 GHz Non-specific short-range devices 100 mW e.i.r.p.     1 July 2014 77 63,72-65,88 GHz Transport and Traffic Telematics devices 40 dBm e.i.r.p. TTT devices placed on the market before the 1 January 2020 are ‘grandfathered’, i.e. they are permitted to use the previous frequency range 63-64 GHz, and otherwise the same conditions apply. This set of usage conditions is only available to vehicle-to-vehicle, vehicle-to-infrastructure and infrastructure-to-vehicle systems. 1 January 2020 78a 75-85 GHz Radio determination devices 34dBm/50 MHz peak e.i.r.p. and -3 dBm/MHz mean e.i.r.p. Automatic power control and antenna requirements as well as requirements on techniques to access spectrum and mitigate interference apply [7], [8], [10]. This set of usage conditions is only available to Level Probing Radar. Established exclusion zones around radio astronomy sites shall be obeyed. 1 July 2014 78b 75-85 GHz Radio determination devices 43 dBm e.i.r.p. [3] Requirements on techniques to access spectrum and mitigate interference apply [7]. This set of usage conditions is only available to Tank Level Probing Radar [c]. 1 July 2014 79a 76-77 GHz Transport and Traffic Telematics devices 55 dBm peak e.i.r.p. and 50 dBm mean e.i.r.p. and 23,5 dBm mean e.i.r.p. for pulse radars Requirements on techniques to access spectrum and mitigate interference apply [7]. Fixed transportation infrastructure radars have to be of a scanning nature in order to limit the illumination time and ensure a minimum silent time to achieve coexistence with automotive radar systems. This set of usage conditions is only available to ground-based vehicle and infrastructure systems. 1 June 2020 79b 76-77 GHz Transport and Traffic Telematics devices 30 dBm peak e.i.r.p. and 3 dBm/MHz average power spectral density Duty cycle limit: ≤ 56 %/s This set of usage conditions is only available to obstacle detection systems for rotorcraft use [4]. 1 January 2018 80a 122-122,25 GHz Non-specific short-range devices 10 dBm/250MHz e.i.r.p. and -48 dBm/MHz at 30° elevation     1 January 2018 80b 122,25-123 GHz Non-specific short-range devices 100 mW e.i.r.p.     1 January 2018 81 244-246 GHz Non-specific short-range devices 100 mW e.i.r.p.     1 July 2014 Applications and devices referred to in Table 2: [a] ‘Metering devices’ means radio devices that are part of bidirectional radio communications systems which allow remote monitoring, measuring and transmission of data in smart grid infrastructures, such as electricity, gas and water. [b] ‘Social alarm devices’ means radio communications systems that allow reliable communication for a person in distress in a confined area to initiate a call for assistance. Typical uses of social alarm are to assist elderly or disabled people. [c] ‘Tank Level Probing Radar’ (TLPR) means a specific type of radiodetermination application, which is used for tank level measurements and is installed in metallic or reinforced concrete tanks, or similar structures made of material with comparable attenuation characteristics. The purpose of the tank is to contain a substance. [d] ‘Model control devices’ means a specific kind of telecommand and telemetry radio equipment that is used to remotely control the movement of models (principally miniature representations of vehicles) in the air, on land or over or under the water surface. [e] An alarm system is a device which uses radio communication support for indicating an alert to a system or a person, as a main functionality, at a distant location when a problem or a specific situation occurs. Radio alarms include social alarms and alarms for security and safety. [f] Medical Body Area Network Systems (MBANSs) are used for medical data acquisition and are intended for low-power wireless networking of a plurality of body-worn sensors and/or actuators as well as of a hub device placed on/around the human body. [g] A network access point in a data network is a fixed terrestrial short-range device that acts as a connection point for the other short-range devices in the data network to service platforms located outside of that data network. The term data network refers to several short-range devices, including the network access point, as network components and to the wireless connections between them. [h] Wireless medical capsule endoscopy is used for medical data acquisition designed for use in medical doctor-patient scenarios with the aim of acquiring images of human digestive tract. [i] Smart tachograph, weight and dimension applications are defined as remote enforcement of the tachograph in Appendix 14 of Commission Implementing Regulation 2016/799  ( 2 ) and for the weights and dimensions enforcement in Article 10d of Directive 2015/719  ( 3 ) . [j] Enclosed NMR sensors are devices where the material/object under investigation is put inside the enclosure of the NMR device. NMR techniques use nuclear magnetic resonance excitation and magnetic field strength response of a material/object under test to get information about material properties based on resonance frequency responses of isotopes of atoms. Nuclear magnetic resonance imaging and magnetic resonance tomography systems are not included in this scope. Other technical requirements and clarifications referred to in Table 2: [1] In band 20 higher field strengths and additional usage restrictions apply for inductive applications. [2] In bands 22, 24, 25, 27a, and 28 higher field strengths and additional usage restrictions apply for inductive applications. [3] The power limit applies inside a closed tank and corresponds to a spectral density of -41,3 dBm/MHz e.i.r.p. outside a 500 litre test tank. [4] Member States can specify exclusion zones or equivalent measures in which the obstacle detection application for rotorcraft use shall not be used for the protection of the radioastronomy service or other national use. Rotorcraft is defined as EASA CS-27 and CS-29 (resp. JAR-27 and JAR-29 for former certifications). [5] Devices shall implement the whole frequency range on a tuning range basis. [6] RFID tags respond at a very low power level (-20 dBm e.r.p.) in a frequency range around the RFID interrogator channels and shall comply with the essential requirements of Directive 2014/53/EU. [7] Techniques to access spectrum and mitigate interference that provide an appropriate level of performance to comply with the essential requirements of Directive 2014/53/EU shall be used. If relevant techniques are described in harmonised standards or parts thereof the references of which have been published in the Official Journal of the European Union under Directive 2014/53/EU, performance at least equivalent to these techniques shall be ensured. [8] Antenna requirements that provide an appropriate level of performance to comply with the essential requirements of Directive 2014/53/EU shall be used. If relevant restrictions are described in harmonised standards or parts thereof the references of which have been published in the Official Journal of the European Union under Directive 2014/53/EU, performance at least equivalent to these restrictions shall be ensured. [9] Transmission mask that provides an appropriate level of performance to comply with the essential requirements of Directive 2014/53/EU shall be used. If relevant restrictions are described in harmonised standards or parts thereof the references of which have been published in the Official Journal of the European Union under Directive 2014/53/EU, performance at least equivalent to these restrictions shall be ensured. [10] Automatic power control that provides an appropriate level of performance to comply with the essential requirements of Directive 2014/53/EU shall be used. If relevant restrictions are described in harmonised standards or parts thereof the references of which have been published in the Official Journal of the European Union under Directive 2014/53/EU, performance at least equivalent to these restrictions shall be ensured. ’ ( 1 )   Council Directive 90/385/EEC of 20 June 1990 on the approximation of the laws of the Member States relating to active implantable medical devices ( OJ L 189, 20.7.1990, p. 17 ). ( 2 )   Commission Implementing Regulation (EU) 2016/799 of 18 March 2016 implementing Regulation (EU) No 165/2014 of the European Parliament and of the Council laying down the requirements for the construction, testing, installation, operation and repair of tachographs and their components ( OJ L 139, 26.5.2016, p. 1 ). ( 3 )   Directive (EU) 2015/719 of the European Parliament and of the Council of 29 April 2015 amending Council Directive 96/53/EC laying down for certain road vehicles circulating within the Community the maximum authorised dimensions in national and international traffic and the maximum authorised weights in international traffic ( OJ L 115, 6.5.2015, p. 1 ).