資料由法律人 LawPlayer整理提供·EU law / curated by LawPlayer from EUR-Lex
The references to harmonised standards for electrical equipment designed for use within certain voltage limits drafted in support of Directive 2014/35/EU, listed in Annex I to this Decision, are hereby published in the Official Journal of the European Union .
Implementing Decision (EU) 2019/1956 is repealed.
However, it shall continue to apply in respect of the reference of harmonised standard listed in Annex II to this Decision until the date of withdrawal of that reference set out in that Annex.
Communication 2018/C 326/02 is repealed.
However, it shall continue to apply in respect of the references of harmonised standards listed in Annex III to this Decision until the dates of withdrawal of those references set out in that Annex.
This Decision shall enter into force on the day of its publication in the Official Journal of the European Union.
ANNEX I
No
Reference of the standard
1.
HD 308 S2:2001
Identification of cores in cables and flexible cords
2.
HD 368 S1:1978
Direct acting recording electrical measuring instruments and their accessories
3.
HD 549 S1:1989
Conference systems – Electrical and audio requirements
4.
HD 597 S1:1992
Coupling capacitors and capacitor dividers
HD 597 S1:1992/AC:1992
5.
HD 603 S1:1994
Distribution cables of rated voltage 0,6/1 kV
HD 603 S1:1994/A3:2007
HD 603 S1:1994/A1:1997
HD 603 S1:1994/A2:2003
6.
HD 604 S1:1994
0,6/1 kV and 1,9/3,3 kV power cables with special fire performance for use in power stations
HD 604 S1:1994/A3:2005
HD 604 S1:1994/A1:1997
HD 604 S1:1994/A2:2002
7.
HD 626 S1:1996
Overhead distribution cables of rated voltage Uo/U(Um): 0,6/1 (1,2) kV
HD 626 S1:1996/A1:1997
HD 626 S1:1996/A2:2002
8.
HD 627 S1:1996
Multicore and multipair cables for installation above and below ground
HD 627 S1:1996/A1:2000
HD 627 S1:1996/A2:2005
9.
HD 639 S1:2002
Electrical accessories – Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs)
HD 639 S1:2002/A1:2003
HD 639 S1:2002/A2:2010
HD 639 S1:2002/AC:2003
10.
EN ISO 11252:2013
Lasers and laser-related equipment – Laser device – Minimum requirements for documentation (ISO 11252:2013)
11.
EN 13637:2015
Building hardware – Electrically controlled exit systems for use on escape routes – Requirements and test methods
12.
EN 50065-4-2:2001
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz – Part 4-2: Low voltage decoupling filters – Safety requirements
EN 50065-4-2:2001/A1:2003
EN 50065-4-2:2001/A2:2005
13.
EN 50065-4-7:2005
Signalling on low-voltage electrical installations in the frequency range 3 kHz to 148,5 kHz and 1,6 MHz to 30 MHz – Part 4-7: Portable low voltage decoupling filters – Safety requirements
EN 50065-4-7:2005/AC:2006
14.
EN 50085-1:2005
Cable trunking systems and cable ducting systems for electrical installations – Part 1: General requirements
EN 50085-1:2005/A1:2013
15.
EN 50085-2-1:2006
Cable trunking systems and cable ducting systems for electrical installations – Part 2-1: Cable trunking systems and cable ducting systems intended for mounting on walls and ceilings
EN 50085-2-1:2006/A1:2011
16.
EN 50085-2-2:2008
Cable trunking systems and cable ducting systems for electrical installations – Part 2-2: Particular requirements for cable trunking systems and cable ducting systems intended for mounting underfloor, flushfloor, or onfloor
17.
EN 50085-2-3:2010
Cable trunking systems and cable ducting systems for electrical installations – Part 2-3: Particular requirements for slotted cable trunking systems intended for installation in cabinets
18.
EN 50085-2-4:2009
Cable trunking systems and cable ducting systems for electrical installations – Part 2-4: Particular requirements for service poles and service posts
19.
EN 50106:2008
Safety of household and similar electrical appliances – Particular rules for routine tests referring to appliances under the scope of EN 60335-1
20.
EN 50117-1:2002
Coaxial cables – Part 1: Generic specification
EN 50117-1:2002/A1:2006
EN 50117-1:2002/A2:2013
21.
EN 50117-2-1:2005
Coaxial cables – Part 2-1: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 1 000 MHz
EN 50117-2-1:2005/A1:2008
EN 50117-2-1:2005/A2:2013
22.
EN 50117-2-2:2004
Coaxial cables – Part 2-2: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 1 000 MHz
EN 50117-2-2:2004/A1:2008
EN 50117-2-2:2004/A2:2013
23.
EN 50117-2-3:2004
Coaxial cables – Part 2-3: Sectional specification for cables used in cabled distribution networks – Distribution and trunk cables for systems operating at 5 MHz – 1 000 MHz
EN 50117-2-3:2004/A1:2008
EN 50117-2-3:2004/A2:2013
24.
EN 50117-2-4:2004
Coaxial cables – Part 2-4: Sectional specification for cables used in cabled distribution networks – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz
EN 50117-2-4:2004/A1:2008
EN 50117-2-4:2004/A2:2013
25.
EN 50117-2-5:2004
Coaxial cables – Part 2-5: Sectional specification for cables used in cabled distribution networks – Outdoor drop cables for systems operating at 5 MHz – 3 000 MHz
EN 50117-2-5:2004/AC:2012
EN 50117-2-5:2004/A1:2008
EN 50117-2-5:2004/A2:2013
26.
EN 50117-3-1:2002
Coaxial cables – Part 3-1: Sectional specifications for cables used in Telecom applications – Miniaturized cables used in digital communication systems
27.
EN 50117-4-1:2008
Coaxial cables – Part 4-1: Sectional specification for cables for BCT cabling in accordance with EN 50173 – Indoor drop cables for systems operating at 5 MHz – 3 000 MHz
EN 50117-4-1:2008/A1:2013
28.
EN 50117-4-2:2015
Coaxial cables – Part 4-2: Sectional specification for CATV cables up to 6 GHz used in cabled distribution networks
29.
EN 50156-1:2015
Electrical equipment for furnaces and ancillary equipment – Part 1: Requirements for application design and installation
30.
EN 50156-2:2015
Electrical equipment for furnaces and ancillary equipment – Part 2: Requirements for design, development and type approval of safety devices and subsystems
31.
EN 50214:2006
Flat polyvinyl chloride sheathed flexible cables
EN 50214:2006/AC:2007
32.
EN 50250:2002
Conversion adaptors for industrial use
EN 50250:2002/A1:2015
EN 50250:2002/AC:2007
33.
EN 50274:2002
Low-voltage switchgear and controlgear assemblies – Protection against electric shock – Protection against unintentional direct contact with hazardous live parts
EN 50274:2002/AC:2009
34.
EN 50288-1:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 1: Generic specification
35.
EN 50288-2-1:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 2-1: Sectional specification for screened cables characterised up to 100 MHz – Horizontal and building backbone cables
36.
EN 50288-2-2:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 2-2: Sectional specification for screened cables characterised up to 100 MHz – Work area and patch cord cables
37.
EN 50288-3-1:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 3-1: Sectional specification for unscreened cables characterised up to 100 MHz – Horizontal and building backbone cables
38.
EN 50288-3-2:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 3-2: Sectional specification for unscreened cables characterised up to 100 MHz – Work area and patch cord cables
39.
EN 50288-4-1:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 4-1: Sectional specification for screened cables characterised up to 600 MHz – Horizontal and building backbone cables
40.
EN 50288-4-2:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 4-2: Sectional specification for screened cables characterised up to 600 MHz – Work area and patch cord cables
41.
EN 50288-5-1:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 5-1: Sectional specification for screened cables characterized up to 250 MHz – Horizontal and building backbone cables
42.
EN 50288-5-2:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 5-2: Sectional specification for screened cables characterized up to 250 MHz – Work area and patch cord cables
43.
EN 50288-6-1:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 6-1: Sectional specification for unscreened cables characterised up to 250 MHz – Horizontal and building backbone cables
44.
EN 50288-6-2:2013
Multi-element metallic cables used in analogue and digital communication and control – Part 6-2: Sectional specification for unscreened cables characterised up to 250 MHz – Work area and patch cord cables
45.
EN 50288-7:2005
Multi-element metallic cables used in analogue and digital communication and control – Part 7: Sectional specification for instrumentation and control cables
46.
EN 50288-8:2012
Multi-element metallic cables used in analogue and digital communication and control – Part 8: Specification for type 1 cables characterised up to 2 MHz
47.
EN 50288-9-1:2012
Multi-element metallic cables used in analogue and digital communication and control – Part 9-1: Sectional specification for screened cables characterised up to 1 000 MHz – Horizontal and building backbone cables
48.
EN 50288-9-2:2015
Multi-element metallic cables used in analogue and digital communication and control – Part 9-2: Sectional specification for screened cables characterized from 1 MHz up to 1 000 MHz for work area, patch cord and data centre applications
49.
EN 50288-10-1:2012
Multi-element metallic cables used in analogue and digital communication and control – Part 10-1: Sectional specification for screened cables characterized up to 500 MHz – Horizontal floor and building backbone cables
50.
EN 50288-10-2:2015
Multi-element metallic cables used in analogue and digital communication and control – Part 10-2: Sectional specification for screened cables characterized from 1 MHz up to 500 MHz for work area, patch cord and data centre applications
51.
EN 50288-11-1:2012
Multi-element metallic cables used in analogue and digital communication and control – Part 11-1: Sectional specification for un-screened cables characterised up to 500 MHz – Horizontal and building backbone cables
52.
EN 50288-11-2:2015
Multi-element metallic cables used in analogue and digital communication and control – Part 11-2: Sectional specification for un-screened cables, characterized from 1 MHz up to 500 MHz for work area, patch cord and data centre applications
53.
EN 50289-1-3:2001
Communication cables – Specifications for test methods – Part 1-3: Electrical test methods – Dielectric strength
54.
EN 50289-1-4:2001
Communication cables – Specifications for test methods – Part 1-4: Electrical test methods – Insulation resistance
55.
EN 50290-2-1:2005
Communication cables – Part 2-1: Common design rules and construction
56.
EN 50290-2-20:2001
Communication cables – Part 2-20: Common design rules and construction – General
57.
EN 50290-2-21:2001
Communication cables – Part 2-21: Common design rules and construction – PVC insulation compounds
EN 50290-2-21:2001/A1:2007/AC:2016
EN 50290-2-21:2001/A1:2007
EN 50290-2-21:2001/AC:2003
58.
EN 50290-2-22:2001
Communication cables – Part 2-22: Common design rules and construction – PVC sheathing compounds
EN 50290-2-22:2001/A1:2007
59.
EN 50290-2-23:2013
Communication cables – Part 2-23: Common design rules and construction – Polyethylene insulation for multi-pair cables used in access telecommunication networks: Outdoor cables
60.
EN 50290-2-24:2002
Communication cables – Part 2-24: Common design rules and construction – PE sheathing
EN 50290-2-24:2002/A1:2008
61.
EN 50290-2-25:2013
Communication cables – Part 2-25: Common design rules and construction – Polypropylene insulation compounds
62.
EN 50290-2-26:2002
Communication cables – Part 2-26: Common design rules and construction – Halogen free flame retardant insulation compounds
EN 50290-2-26:2002/A1:2007
63.
EN 50290-2-27:2002
Communication cables – Part 2-27: Common design rules and construction – Halogen free flame retardant thermoplastic sheathing compounds
EN 50290-2-27:2002/A1:2007
EN 50290-2-27:2002/A1:2007/AC:2010
64.
EN 50290-2-28:2002
Communication cables – Part 2-28: Common design rules and construction – Filling compounds for filled cables
65.
EN 50290-2-29:2002
Communication cables – Part 2-29: Common design rules and construction – Cross-linked PE insulation compounds
66.
EN 50290-2-30:2002
Communication cables – Part 2-30: Common design rules and construction – Poly(tetrafluoroethylene-hexafluoropropylene) (FEP) insulation and sheathing
67.
EN 50290-4-1:2014
Communication cables – Part 4-1: General considerations for the use of cables – Environmental conditions and safety aspects
68.
EN 50290-4-2:2014
Communication cables – Part 4-2: General considerations for the use of cables – Guide to use
69.
EN 50364:2010
Limitation of human exposure to electromagnetic fields from devices operating in the frequency range 0 Hz to 300 GHz, used in Electronic Article Surveillance (EAS), Radio Frequency Identification (RFID) and similar applications
70.
EN 50369:2005
Liquid tight sheathing systems for cable management
71.
EN 50406-1:2004
End user multi-pair cables used in high bit rate telecommunication networks – Part 1: Aerial cables
72.
EN 50406-2:2004
End user multi-pair cables used in high bit rate telecommunication networks – Part 2: Duct and buried cables
73.
EN 50407-1:2004
Multi-pair cables used in high bit rate digital access telecommunication networks – Part 1: Outdoor cables
74.
EN 50407-3:2014
Multi-pair cables used in high bit rate digital access telecommunications networks – Part 3: Indoor multi-pair/quad riser cables up to 100 MHz for maximum length of connection 100 m supporting universal services, xDSL and applications up to 100 Mbit/s over IP
75.
EN 50428:2005
Switches for household and similar fixed electrical installations – Collateral standard – Switches and related accessories for use in home and building electronic systems (HBES)
EN 50428:2005/A1:2007
EN 50428:2005/A2:2009
76.
EN 50441-1:2012
Cables for indoor residential telecommunication installations – Part 1: Unscreened cables – Grade 1
77.
EN 50441-2:2012
Cables for indoor residential telecommunication installations – Part 2: Screened cables – Grade 1
78.
EN 50441-3:2006
Cables for indoor residential telecommunication installations – Part 3: Screened cables – Grade 3
79.
EN 50441-4:2012
Cables for indoor residential telecommunication installations – Part 4: Cables up to 1 200 MHz – Grade 3
80.
EN 50445:2008
Product family standard to demonstrate compliance of equipment for resistance welding, arc welding and allied processes with the basic restrictions related to human exposure to electromagnetic fields (0 Hz – 300 GHz)
81.
EN 50491-4-1:2012
General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) – Part 4-1: General functional safety requirements for products intended to be integrated in Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS)
82.
EN 50491-6-1:2014
General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) – Part 6-1: HBES installations – Installation and planning
83.
EN 50520:2020
Cover plates and cover tapes for the protection and location warning of buried cables or buried conduits in underground installations
EN 50520:2020/A1:2021
84.
EN 50525-1:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 1: General requirements
85.
EN 50525-2-11:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) – Part 2-11: Cables for general applications – Flexible cables with thermoplastic PVC insulation
86.
EN 50525-2-12:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) – Part 2-12: Cables for general applications – Cables with thermoplastic PVC insulation for extensible leads
87.
EN 50525-2-21:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (Uo/U) – Part 2-21: Cables for general applications – Flexible cables with crosslinked elastomeric insulation
EN 50525-2-21:2011/AC:2013
88.
EN 50525-2-22:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-22: Cables for general applications – High flexibility braided cables with crosslinked elastomeric insulation
89.
EN 50525-2-31:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-31: Cables for general applications – Single core non-sheathed cables with thermoplastic PVC insulation
90.
EN 50525-2-41:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-41: Cables for general applications – Single core cables with crosslinked silicone rubber insulation
91.
EN 50525-2-42:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-42: Cables for general applications – Single core non-sheathed cables with crosslinked EVA insulation
92.
EN 50525-2-51:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-51: Cables for general applications – Oil resistant control cables with thermoplastic PVC insulation
93.
EN 50525-2-71:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-71: Cables for general applications – Flat tinsel cables (cords) with thermoplastic PVC insulation
94.
EN 50525-2-72:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-72: Cables for general applications – Flat divisible cables (cords) with thermoplastic PVC insulation
95.
EN 50525-2-81:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-81: Cables for general applications – Cables with crosslinked elastomeric covering for arc welding
96.
EN 50525-2-82:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-82: Cables for general applications – Cables with crosslinked elastomeric insulation for decorative chains
97.
EN 50525-2-83:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 2-83: Cables for general applications – Multicore cables with crosslinked silicone rubber insulation
98.
EN 50525-3-11:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-11: Cables with special fire performance – Flexible cables with halogen-free thermoplastic insulation, and low emission of smoke
99.
EN 50525-3-21:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-21: Cables with special fire performance – Flexible cables with halogen-free crosslinked insulation, and low emission of smoke
EN 50525-3-21:2011/AC:2013
100.
EN 50525-3-31:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-31: Cables with special fire performance – Single core non-sheathed cables with halogen-free thermoplastic insulation, and low emission of smoke
101.
EN 50525-3-41:2011
Electric cables – Low voltage energy cables of rated voltages up to and including 450/750 V (U0/U) – Part 3-41: Cables with special fire performance – Single core non-sheathed cables with halogen-free crosslinked insulation, and low emission of smoke
102.
EN 50539-11:2013
Low-voltage surge protective devices – Surge protective devices for specific application including d.c. – Part 11: Requirements and tests for SPDs in photovoltaic applications
EN 50539-11:2013/A1:2014
103.
EN 50550:2011
Power frequency overvoltage protective device for household and similar applications (POP)
EN 50550:2011/AC:2012
EN 50550:2011/A1:2014
104.
EN 50556:2011
Road traffic signal systems
105.
EN 50615:2015
Household and similar electrical appliances – Safety – Particular requirements for devices for fire prevention and suppression for electric hobs (cooktops)
106.
EN 50618:2014
Electric cables for photovoltaic systems
107.
EN 50620:2017
Electric cables – Charging cables for electric vehicles
EN 50620:2017/A1:2019
108.
EN 50689:2021
Safety of laser products – Particular Requirements for Consumer Laser Products
109.
EN 60034-1:2010
Rotating electrical machines – Part 1: Rating and performance
EN 60034-1:2010/AC:2010
110.
EN 60034-5:2001
Rotating electrical machines – Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) – Classification
EN 60034-5:2001/A1:2007
111.
EN 60034-6:1993
Rotating electrical machines – Part 6: Methods of cooling (IC Code)#IEC 60034-6:1991
112.
EN 60034-7:1993
Rotating electrical machines – Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM Code)
EN 60034-7:1993/A1:2001
113.
EN 60034-8:2007
Rotating electrical machines – Part 8: Terminal markings and direction of rotation
EN 60034-8:2007/A1:2014
114.
EN 60034-9:2005
Rotating electrical machines – Part 9: Noise limits
EN 60034-9:2005/A1:2007
115.
EN 60034-11:2004
Rotating electrical machines – Part 11: Thermal protection
116.
EN 60034-12:2002
Rotating electrical machines – Part 12: Starting performance of single-speed three-phase cage induction motors
EN 60034-12:2002/A1:2007
117.
EN 60034-14:2004
Rotating electrical machines – Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher – Measurement, evaluation and limits of vibration severity
EN 60034-14:2004/A1:2007
118.
EN 60051-1:1998
Direct acting indicating analogue electrical measuring instruments and their accessories – Part 1: Definitions and general requirements common to all parts
119.
EN 60051-2:1989
Direct acting indicating analogue electrical measuring instruments and their accessories – Part 2: Special requirements for ammeters and voltmeters
120.
EN 60051-3:1989
Direct acting indicating analogue electrical measuring instruments and their accessories – Part 3: Special requirements for wattmeters and varmeters
EN 60051-3:1989/A1:1995
121.
EN 60051-4:1989
Direct acting indicating analogue electrical measuring instruments and their accessories – Part 4: Special requirements for frequency meters
122.
EN 60051-5:1989
Direct acting indicating analogue electrical measuring instruments and their accessories – Part 5: Special requirements for phase meters, power factor meters and synchroscopes
123.
EN 60051-6:1989
Direct acting indicating analogue electrical measuring instruments and their accessories – Part 6: Special requirements for ohmmeters (impedance meters) and conductance meters
124.
EN 60051-7:1989
Direct acting indicating analogue electrical measuring instruments and their accessories – Part 7: Special requirements for multi-function instruments
125.
EN 60051-8:1989
Direct acting indicating analogue electrical measuring instruments and their accessories – Part 8: Special requirements for accessories
126.
EN 60051-9:1989
Direct acting indicating analogue electrical-measuring instruments and their accessories – Part 9: Recommended test methods
EN 60051-9:1989/A1:1995
EN 60051-9:1989/A2:1995
127.
EN 60110-1:1998
Power capacitors for induction heating installations – Part 1: General
128.
EN 60127-1:2006
Miniature fuses – Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links
EN 60127-1:2006/A1:2011
EN 60127-1:2006/A2:2015
129.
EN 60127-2:2014
Miniature fuses – Part 2: Cartridge fuse-links
130.
EN 60127-3:1996
Miniature fuses – Part 3: Sub-miniature fuse-links
EN 60127-3:1996/A2:2003
EN 60127-3:1996/AC:1996
131.
EN 60127-4:2005
Miniature fuses – Part 4: Universal modular fuse-links (UMF) – Through-hole and surface mount types
EN 60127-4:2005/A1:2009
EN 60127-4:2005/A2:2013
132.
EN 60127-6:2014
Miniature fuses – Part 6: Fuse-holders for miniature fuse-links
133.
EN 60127-7:2016
Miniature fuses – Part 7: Miniature fuse-links for special applications
134.
EN 60143-2:2013
Series capacitors for power systems – Part 2: Protective equipment for series capacitor banks
135.
EN 60155:1995
Glow-starters for fluorescent lamps
EN 60155:1995/A1:1995
EN 60155:1995/A2:2007
136.
EN 60204-1:2018
Safety of machinery – Electrical equipment of machines – Part 1: General requirements
137.
EN 60204-32:2008
Safety of machinery – Electrical equipment of machines – Part 32: Requirements for hoisting machines
138.
EN 60215:1989
Safety requirements for radio transmitting equipment
EN 60215:1989/A1:1992
EN 60215:1989/A2:1994
139.
EN IEC 60238:2018
Edison screw lampholders
140.
EN 60252-1:2011
AC motor capacitors – Part 1: General – Performance, testing and rating – Safety requirements – Guidance for installation and operation
EN 60252-1:2011/A1:2013
141.
EN 60252-2:2011
AC motor capacitors – Part 2: Motor start capacitors
EN 60252-2:2011/A1:2013
142.
EN 60255-27:2014
Measuring relays and protection equipment – Part 27: Product safety requirements
143.
EN 60269-1:2007
Low-voltage fuses – Part 1: General requirements
EN 60269-1:2007/A1:2009
EN 60269-1:2007/A2:2014
144.
HD 60269-2:2013
Low-voltage fuses – Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) – Examples of standardized systems of fuses A to K
145.
HD 60269-3:2010
Low-voltage fuses – Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) – Examples of standardized systems of fuses A to F
HD 60269-3:2010/A1:2013
146.
EN 60269-4:2009
Low-voltage fuses – Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices
EN 60269-4:2009/A1:2012
147.
EN 60269-6:2011
Low-voltage fuses – Part 6: Supplementary requirements for fuse-links for the protection of solar photovoltaic energy systems
148.
EN 60309-1:1999
Plugs, socket-outlets and couplers for industrial purposes – Part 1: General requirements
EN 60309-1:1999/A1:2007
EN 60309-1:1999/A2:2012
EN 60309-1:1999/A1:2007/AC:2014
149.
EN 60309-2:1999
Plugs, socket-outlets and couplers for industrial purposes – Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
EN 60309-2:1999/A1:2007
EN 60309-2:1999/A2:2012
150.
EN 60309-4:2007
Plugs, socket-outlets and couplers for industrial purposes – Part 4: Switched socket-outlets and connectors with or without interlock
EN 60309-4:2007/A1:2012
151.
EN IEC 60320-1:2021
Appliance couplers for household and similar general purposes – Part 1: General requirements
152.
EN 60320-2-1:2000
Appliance couplers for household and similar general purposes – Part 2-1: Sewing machine couplers
153.
EN 60320-2-2:1998
Appliance couplers for household and similar general purposes – Part 2-2: Interconnection couplers for household and similar equipment
154.
EN IEC 60320-2-4:2021
Appliance couplers for household and similar general purposes – Part 2-4: Couplers dependent on appliance weight for engagement
155.
EN 60335-1:2012
Household and similar electrical appliances – Safety – Part 1: General requirements
EN 60335-1:2012/AC:2014
EN 60335-1:2012/A11:2014
EN 60335-1:2012/A13:2017
EN 60335-1:2012/A1:2019
EN 60335-1:2012/A14:2019
EN 60335-1:2012/A2:2019
EN 60335-1:2012/A15:2021
156.
EN 60335-2-2:2010
Household and similar electrical appliances – Safety – Part 2-2: Particular requirements for vacuum cleaners and water-suction cleaning appliances
EN 60335-2-2:2010/A11:2012
EN 60335-2-2:2010/A1:2013
157.
EN 60335-2-3:2016
Household and similar electrical appliances – Safety – Part 2-3: Particular requirements for electric irons
EN 60335-2-3:2016/A1:2020
158.
EN 60335-2-4:2010
Household and similar electrical appliances – Safety – Part 2-4: Particular requirements for spin extractors
EN 60335-2-4:2010/A1:2015
EN 60335-2-4:2010/A11:2018
EN 60335-2-4:2010/A2:2019
159.
EN 60335-2-5:2015
Household and similar electrical appliances – Safety – Part 2-5: Particular requirements for dishwashers
EN 60335-2-5:2015/A11:2019
EN 60335-2-5:2015/A1:2020
160.
EN 60335-2-6:2015
Household and similar electrical appliances – Safety – Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances
EN 60335-2-6:2015/A11:2020
161.
EN 60335-2-7:2010
Household and similar electrical appliances – Safety – Part 2-7: Particular requirements for washing machines
EN 60335-2-7:2010/A11:2013
EN 60335-2-7:2010/A1:2013
EN 60335-2-7:2010/A2:2019
162.
EN 60335-2-8:2015
Household and similar electrical appliances – Safety – Part 2-8: Particular requirements for shavers, hair clippers and similar appliances
EN 60335-2-8:2015/A1:2016
163.
EN 60335-2-9:2003
Household and similar electrical appliances – Safety – Part 2-9: Particular requirements for grills, toasters and similar portable cooking appliances
EN 60335-2-9:2003/A1:2004
EN 60335-2-9:2003/A12:2007
EN 60335-2-9:2003/A13:2010
EN 60335-2-9:2003/A2:2006
EN 60335-2-9:2003/A13:2010/AC:2011
EN 60335-2-9:2003/A13:2010/AC:2012
Restriction: The application of the following parts of standard EN 60335-2-9:2003, as last amended by A13:2010, does not confer a presumption of conformity to the safety objectives laid down in point 1(c) of Annex I to Directive 2014/35/EU, in conjunction with point 2(b) of that Annex: – footnote b of Table Z101 in Section 11, – the parts of Section 7.1 which refer to footnote b of Table Z101, – the parts of Section 11.Z10x which refer to ventilation openings.
164.
EN 60335-2-10:2003
Household and similar electrical appliances – Safety – Part 2-10: Particular requirements for floor treatment machines and wet scrubbing machines
EN 60335-2-10:2003/A1:2008
165.
EN IEC 60335-2-11:2022
Household and similar electrical appliances – Safety – Part 2-11: Particular requirements for tumble dryers
EN IEC 60335-2-11:2022/A11:2022
166.
EN 60335-2-12:2003
Household and similar electrical appliances – Safety – Part 2-12: Particular requirements for warming plates and similar appliances
EN 60335-2-12:2003/A1:2008
EN 60335-2-12:2003/A11:2019
EN 60335-2-12:2003/A2:2019
167.
EN 60335-2-13:2010
Household and similar electrical appliances – Safety – Part 2-13: Particular requirements for deep fat fryers, frying pans and similar appliances
EN 60335-2-13:2010/A11:2012
EN 60335-2-13:2010/A1:2019
168.
EN 60335-2-15:2016
Household and similar electrical appliances – Safety – Part 2-15: Particular requirements for appliances for heating liquids
EN 60335-2-15:2016/A11:2018
EN 60335-2-15:2016/A1:2021
EN 60335-2-15:2016/A12:2021
EN 60335-2-15:2016/A2:2021
169.
EN 60335-2-16:2003
Household and similar electrical appliances – Safety – Part 2-16: Particular requirements for food waste disposers
EN 60335-2-16:2003/A1:2008
EN 60335-2-16:2003/A2:2012
EN 60335-2-16:2003/A11:2018
170.
EN 60335-2-17:2013
Household and similar electrical appliances – Safety – Part 2-17: Particular requirements for blankets, pads, clothing and similar flexible heating appliances
EN 60335-2-17:2013/A11:2019
EN 60335-2-17:2013/A1:2020
EN 60335-2-17:2013/A2:2021
171.
EN 60335-2-21:2021
Household and similar electrical appliances – Safety – Part 2-21: Particular requirements for storage water heaters
EN 60335-2-21:2021/A1:2021
172.
EN 60335-2-23:2003
Household and similar electrical appliances – Safety – Part 2-23: Particular requirements for appliances for skin or hair care
EN 60335-2-23:2003/A11:2010/AC:2012
EN 60335-2-23:2003/A11:2010
EN 60335-2-23:2003/A1:2008
EN 60335-2-23:2003/A2:2015
173.
EN IEC 60335-2-24:2022
Household and similar electrical appliances – Safety – Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers
EN IEC 60335-2-24:2022/A11:2022
174.
EN IEC 60335-2-25:2021
Household and similar electrical appliances – Safety – Part 2-25: Particular requirements for microwave ovens, including combination microwave ovens
EN IEC 60335-2-25:2021/A11:2021
175.
EN 60335-2-26:2003
Household and similar electrical appliances – Safety – Part 2-26: Particular requirements for clocks
EN 60335-2-26:2003/A1:2008
176.
EN 60335-2-27:2013
Household and similar electrical appliances – Safety – Part 2-27: Particular requirements for appliances for skin exposure to ultraviolet and infrared radiation
EN 60335-2-27:2013/A1:2020
EN 60335-2-27:2013/A2:2020
EN 60335-2-27:2013/AC:2021-11
177.
EN 60335-2-28:2003
Household and similar electrical appliances – Safety – Part 2-28: Particular requirements for sewing machines
EN 60335-2-28:2003/A1:2008
EN 60335-2-28:2003/A11:2018
178.
EN 60335-2-29:2021
Household and similar electrical appliances – Safety – Part 2-29: Particular requirements for battery chargers
EN 60335-2-29:2021/A1:2021
179.
EN 60335-2-30:2009
Household and similar electrical appliances – Safety – Part 2-30: Particular requirements for room heaters
EN 60335-2-30:2009/A11:2012
EN 60335-2-30:2009/AC:2010
EN 60335-2-30:2009/AC:2014
EN 60335-2-30:2009/A1:2020
EN 60335-2-30:2009/A12:2020
EN 60335-2-30:2009/A13:2022
EN 60335-2-30:2009/A2:2022
180.
EN 60335-2-31:2014
Household and similar electrical appliances – Safety – Part 2-31: Particular requirements for range hoods and other cooking fume extractors
181.
EN 60335-2-32:2003
Household and similar electrical appliances – Safety – Part 2-32: Particular requirements for massage appliances
EN 60335-2-32:2003/A1:2008
EN 60335-2-32:2003/A2:2015
182.
EN 60335-2-34:2013
Household and similar electrical appliances – Safety – Part 2-34: Particular requirements for motor-compressors
183.
EN 60335-2-35:2016
Household and similar electrical appliances – Safety – Part 2-35: Particular requirements for instantaneous water heaters
EN 60335-2-35:2016/A1:2019
EN 60335-2-35:2016/A2:2021
184.
EN 60335-2-36:2002
Household and similar electrical appliances – Safety – Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements
EN 60335-2-36:2002/A1:2004
EN 60335-2-36:2002/A11:2012
EN 60335-2-36:2002/A2:2008
EN 60335-2-36:2002/AC:2007
185.
EN 60335-2-37:2002
Household and similar electrical appliances – Safety – Part 2-37: Particular requirements for commercial electric deep fat fryers
EN 60335-2-37:2002/A1:2008
EN 60335-2-37:2002/A11:2012
EN 60335-2-37:2002/AC:2007
186.
EN 60335-2-38:2003
Household and similar electrical appliances – Safety – Part 2-38: Particular requirements for commercial electric griddles and griddle grills
EN 60335-2-38:2003/A1:2008
EN 60335-2-38:2003/AC:2007
187.
EN 60335-2-39:2003
Household and similar electrical appliances – Safety – Part 2-39: Particular requirements for commercial electric multi-purpose cooking pans
EN 60335-2-39:2003/A1:2004
EN 60335-2-39:2003/A2:2008
EN 60335-2-39:2003/AC:2007
188.
EN 60335-2-40:2003
Household and similar electrical appliances – Safety – Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
EN 60335-2-40:2003/A11:2004
EN 60335-2-40:2003/A12:2005
EN 60335-2-40:2003/A1:2006
EN 60335-2-40:2003/A13:2012/AC:2013
EN 60335-2-40:2003/A13:2012
EN 60335-2-40:2003/A2:2009
EN 60335-2-40:2003/AC:2006
EN 60335-2-40:2003/AC:2010
189.
EN IEC 60335-2-41:2021
Household and similar electrical appliances – Safety – Particular requirements for pumps
EN IEC 60335-2-41:2021/A11:2021
190.
EN 60335-2-42:2003
Household and similar electrical appliances – Safety – Part 2-42: Particular requirements for commercial electric forced convection ovens, steam cookers and steam-convection ovens
EN 60335-2-42:2003/A1:2008
EN 60335-2-42:2003/A11:2012
EN 60335-2-42:2003/AC:2007
191.
EN IEC 60335-2-43:2020
Household and similar electrical appliances – Safety – Part 2-43: Particular requirements for clothes dryers and towel rails
EN IEC 60335-2-43:2020/A11:2020
192.
EN 60335-2-44:2002
Household and similar electrical appliances – Safety – Part 2-44: Particular requirements for ironers
EN 60335-2-44:2002/A1:2008
EN 60335-2-44:2002/A2:2012
193.
EN 60335-2-45:2002
Household and similar electrical appliances – Safety – Part 2-45: Particular requirements for portable heating tools and similar appliances
EN 60335-2-45:2002/A1:2008
EN 60335-2-45:2002/A2:2012
194.
EN 60335-2-47:2003
Household and similar electrical appliances – Safety – Part 2-47: Particular requirements for commercial electric boiling pans
EN 60335-2-47:2003/A1:2008
EN 60335-2-47:2003/A11:2012
EN 60335-2-47:2003/AC:2007
EN 60335-2-47:2003/A2:2019
195.
EN 60335-2-48:2003
Household and similar electrical appliances – Safety – Part 2-48: Particular requirements for commercial electric grillers and toasters
EN 60335-2-48:2003/A1:2008
EN 60335-2-48:2003/A11:2012
EN 60335-2-48:2003/AC:2007
EN 60335-2-48:2003/A2:2019
196.
EN 60335-2-49:2003
Household and similar electrical appliances – Safety – Part 2-49: Particular requirements for commercial electric appliances for keeping food and crockery warm
EN 60335-2-49:2003/A1:2008
EN 60335-2-49:2003/A11:2012
EN 60335-2-49:2003/AC:2007
EN 60335-2-49:2003/A2:2019
197.
EN 60335-2-50:2003
Household and similar electrical appliances – Safety – Part 2-50: Particular requirements for commercial electric bains-marie
EN 60335-2-50:2003/A1:2008
EN 60335-2-50:2003/AC:2007
198.
EN 60335-2-51:2003
Household and similar electrical appliances – Safety – Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations
EN 60335-2-51:2003/A1:2008
EN 60335-2-51:2003/A2:2012
199.
EN 60335-2-52:2003
Household and similar electrical appliances – Safety – Part 2-52: Particular requirements for oral hygiene appliances
EN 60335-2-52:2003/A11:2010/AC:2012
EN 60335-2-52:2003/A11:2010
EN 60335-2-52:2003/A1:2008
EN 60335-2-52:2003/A12:2019
200.
EN 60335-2-53:2011
Household and similar electrical appliances – Safety – Part 2-53: Particular requirements for sauna heating appliances and infrared cabins
201.
EN 60335-2-54:2008
Household and similar electrical appliances – Safety – Part 2-54: Particular requirements for surface-cleaning appliances for household use employing liquids or steam
EN 60335-2-54:2008/A11:2012/AC:2015
EN 60335-2-54:2008/A11:2012
EN 60335-2-54:2008/A1:2015
EN 60335-2-54:2008/A12:2021
EN 60335-2-54:2008/A2:2021
202.
EN 60335-2-55:2003
Household and similar electrical appliances – Safety – Part 2-55: Particular requirements for electrical appliances for use with aquariums and garden ponds
EN 60335-2-55:2003/A1:2008
EN 60335-2-55:2003/A11:2018
203.
EN 60335-2-56:2003
Household and similar electrical appliances – Safety – Part 2-56: Particular requirements for projectors and similar appliances
EN 60335-2-56:2003/A1:2008
EN 60335-2-56:2003/A2:2014
204.
EN 60335-2-58:2005
Household and similar electrical appliances – Safety – Part 2-58: Particular requirements for commercial electric dishwashing machines
205.
EN 60335-2-59:2003
Household and similar electrical appliances – Safety – Part 2-59: Particular requirements for insect killers
EN 60335-2-59:2003/A1:2006
EN 60335-2-59:2003/A2:2009
EN 60335-2-59:2003/A11:2018
206.
EN 60335-2-60:2003
Household and similar electrical appliances – Safety – Part 2-60: Particular requirements for whirlpool baths and whirlpool spas
EN 60335-2-60:2003/A1:2005
EN 60335-2-60:2003/A12:2010
EN 60335-2-60:2003/A11:2010
EN 60335-2-60:2003/A2:2008
207.
EN 60335-2-61:2003
Household and similar electrical appliances – Safety – Part 2-61: Particular requirements for thermal-storage room heaters
EN 60335-2-61:2003/A1:2005
EN 60335-2-61:2003/A2:2008
EN 60335-2-61:2003/A11:2019
EN 60335-2-61:2003/A12:2021
208.
EN 60335-2-62:2003
Household and similar electrical appliances – Safety – Part 2-62: Particular requirements for commercial electric rinsing sinks
EN 60335-2-62:2003/A1:2008
EN 60335-2-62:2003/AC:2007
209.
EN 60335-2-65:2003
Household and similar electrical appliances – Safety – Part 2-65: Particular requirements for air-cleaning appliances
EN 60335-2-65:2003/A1:2008
EN 60335-2-65:2003/A11:2012
210.
EN 60335-2-66:2003
Household and similar electrical appliances – Safety – Part 2-66: Particular requirements for water-bed heaters
EN 60335-2-66:2003/A1:2008
EN 60335-2-66:2003/A2:2012
EN 60335-2-66:2003/A11:2019
211.
EN 60335-2-70:2002
Household and similar electrical appliances – Safety – Part 2-70: Particular requirements for milking machines
212.
EN 60335-2-71:2003
Household and similar electrical appliances – Safety – Part 2-71: Particular requirements for electrical heating appliances for breeding and rearing animals
EN 60335-2-71:2003/A1:2007
213.
EN 60335-2-73:2003
Household and similar electrical appliances – Safety – Part 2-73: Particular requirements for fixed immersion heaters
EN 60335-2-73:2003/A1:2006
EN 60335-2-73:2003/A2:2009
EN 60335-2-73:2003/A11:2021
214.
EN 60335-2-74:2003
Household and similar electrical appliances – Safety – Part 2-74: Particular requirements for portable immersion heaters
EN 60335-2-74:2003/A1:2006
EN 60335-2-74:2003/A2:2009
EN 60335-2-74:2003/A11:2018
215.
EN 60335-2-75:2004
Household and similar electrical appliances – Safety – Part 2-75: Particular requirements for commercial dispensing appliances and vending machines
EN 60335-2-75:2004/A11:2006
EN 60335-2-75:2004/A1:2005
EN 60335-2-75:2004/A12:2010
EN 60335-2-75:2004/A2:2008
216.
EN 60335-2-78:2003
Household and similar electrical appliances – Safety – Part 2-78: Particular requirements for outdoor barbecues
EN 60335-2-78:2003/A1:2008
EN 60335-2-78:2003/A11:2020
217.
EN 60335-2-80:2003
+6Household and similar electrical appliances – Safety – Part 2-80: Particular requirements for fans
EN 60335-2-80:2003/A1:2004
EN 60335-2-80:2003/A2:2009
218.
EN 60335-2-81:2003
Household and similar electrical appliances – Safety – Part 2-81: Particular requirements for foot warmers and heating mats
EN 60335-2-81:2003/A1:2007
EN 60335-2-81:2003/A2:2012
219.
EN 60335-2-82:2003
Household and similar electrical appliances – Safety – Part 2-82: Particular requirements for amusement machines and personal service machines
EN 60335-2-82:2003/A1:2008
EN 60335-2-82:2003/A2:2020
220.
EN 60335-2-83:2002
Household and similar electrical appliances – Safety – Part 2-83: Particular requirements for heated gullies for roof drainage
EN 60335-2-83:2002/A1:2008
221.
EN IEC 60335-2-84:2021
Household and similar electrical appliances – Safety – Part 2-84: Particular requirements for toilet appliances
EN IEC 60335-2-84:2021/A11:2021
222.
EN 60335-2-85:2003
Household and similar electrical appliances – Safety – Part 2-85: Particular requirements for fabric steamers
EN 60335-2-85:2003/A1:2008
EN 60335-2-85:2003/A11:2018
EN 60335-2-85:2003/A2:2020
223.
EN 60335-2-86:2003
Household and similar electrical appliances – Safety – Part 2-86: Particular requirements for electric fishing machines
EN 60335-2-86:2003/A1:2005
EN 60335-2-86:2003/A11:2016
EN 60335-2-86:2003/A2:2016
224.
EN 60335-2-87:2002
Household and similar electrical appliances – Safety – Part 2-87: Particular requirements for electrical animal-stunning equipment
EN 60335-2-87:2002/A1:2007
EN 60335-2-87:2002/A2:2019
225.
EN 60335-2-88:2002
Household and similar electrical appliances – Safety – Part 2-88: Particular requirements for humidifiers intended for use with heating, ventilation, or air-conditioning systems
226.
EN 60335-2-90:2006
Household and similar electrical appliances – Safety – Part 2-90: Particular requirements for commercial microwave ovens
EN 60335-2-90:2006/A1:2010
227.
EN IEC 60335-2-96:2021
Household and similar electrical appliances – Safety – Part 2-96: Particular requirements for flexible sheet heating elements for room heating
EN IEC 60335-2-96:2021/A11:2021
228.
EN 60335-2-97:2006
Household and similar electrical appliances – Safety – Part 2-97: Particular requirements for drives for rolling shutters, awnings, blinds and similar equipment
EN 60335-2-97:2006/A11:2008
EN 60335-2-97:2006/A12:2015
EN 60335-2-97:2006/A2:2010
229.
EN 60335-2-98:2003
Household and similar electrical appliances – Safety – Part 2-98: Particular requirements for humidifiers
EN 60335-2-98:2003/A1:2005
EN 60335-2-98:2003/A2:2008
EN 60335-2-98:2003/A11:2019
230.
EN 60335-2-99:2003
Household and similar electrical appliances – Safety – Part 2-99: Particular requirements for commercial electric hoods
231.
EN 60335-2-101:2002
Household and similar electrical appliances – Safety – Part 2-101: Particular requirements for vaporizers
EN 60335-2-101:2002/A1:2008
EN 60335-2-101:2002/A2:2014
232.
EN 60335-2-102:2016
Household and similar electrical appliances – Safety – Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
233.
EN IEC 60335-2-105:2021
Household and similar electrical appliances – Safety – Part 2-105: Particular requirements for multifunctional shower cabinets
EN IEC 60335-2-105:2021/A11:2021
234.
EN 60335-2-106:2007
Household and similar electrical appliances – Safety – Part 2-106: Particular requirements for heated carpets and for heating units for room heating installed under removable floor coverings
235.
EN 60335-2-108:2008
Household and similar electrical appliances – Safety – Part 2-108: Particular requirements for electrolysers
236.
EN 60335-2-109:2010
Household and similar electrical appliances – Safety – Part 2-109: Particular requirements for UV radiation water treatment appliances
EN 60335-2-109:2010/A1:2018
EN 60335-2-109:2010/A2:2018
237.
EN 60358-1:2012
Coupling capacitors and capacitor dividers – Part 1: General rules
EN 60358-1:2012/AC:2013
238.
EN 60360:1998
Standard method of measurement of lamp cap temperature rise
239.
EN 60399:2004
Barrel thread for lampholders with shade holder ring
EN 60399:2004/A1:2008
240.
EN 60400:2017
Lampholders for tubular fluorescent lamps and starterholders
EN 60400:2017/A1:2021
241.
EN 60423:2007
Conduit systems for cable management – Outside diameters of conduits for electrical installations and threads for conduits and fittings
242.
EN 60432-1:2000
Incandescent lamps – Safety specifications – Part 1: Tungsten filament lamps for domestic and similar general lighting purposes
EN 60432-1:2000/A1:2005
EN 60432-1:2000/A2:2012
243.
EN 60432-2:2000
Incandescent lamps – Safety specifications – Part 2: Tungsten halogen lamps for domestic and similar general lighting purposes
EN 60432-2:2000/A1:2005
EN 60432-2:2000/A2:2012
244.
EN 60432-3:2013
Incandescent lamps – Safety specifications – Part 3: Tungsten-halogen lamps (non-vehicle)
245.
EN 60477:1997
Laboratory d.c. resistors
EN 60477:1997/A1:1997
246.
EN 60477-2:1997
Laboratory resistors – Part 2: Laboratory a.c. resistors
EN 60477-2:1997/A1:1997
247.
EN 60519-1:2015
Safety in installations for electroheating and electromagnetic processing – Part 1: General requirements
248.
EN 60519-2:2006
Safety in electroheat installations – Part 2: Particular requirements for resistance heating equipment
249.
EN 60519-3:2005
Safety in electroheat installations – Part 3: Particular requirements for induction and conduction heating and induction melting installations
250.
EN 60519-4:2013
Safety in electroheating installations – Part 4: Particular requirements for arc furnace installations
251.
EN 60519-6:2011
Safety in electroheat installations – Part 6: Specifications for safety in industrial microwave heating equipment
252.
EN 60519-7:2008
Safety in electroheat installations – Part 7: Particular requirements for installations with electron guns
253.
EN 60519-8:2005
Safety in electroheat installations – Part 8: Particular requirements for electroslag remelting furnaces
254.
EN 60519-9:2005
Safety in electroheat installations – Part 9: Particular requirements for high-frequency dielectric heating installations
255.
EN 60519-10:2013
Safety in electroheating installations – Part 10: Particular requirements for electrical resistance trace heating systems for industrial and commercial applications
256.
EN 60519-12:2013
Safety in electroheating installations – Part 12: Particular requirements for infrared electroheating installations
257.
EN 60519-21:2009
Safety in electroheat installations – Part 21: Particular requirements for resistance heating equipment – Heating and melting glass equipment#IEC 60519-21:2008
258.
EN 60523:1993
Direct-current potentiometers
EN 60523:1993/A2:1997
259.
EN 60524:1993
Direct-current resistive volt ratio boxes
EN 60524:1993/A2:1997
260.
EN 60529:1991
Degrees of protection provided by enclosures (IP Code)#IEC 60529:1989
EN 60529:1991/A1:2000
EN 60529:1991/A2:2013
EN 60529:1991/AC:1993
EN 60529:1991/AC:2016-12
EN 60529:1991/A2:2013/AC:2019-02
261.
EN 60564:1993
D.C. bridges for measuring resistance
EN 60564:1993/A2:1997
262.
EN 60570:2003
Electrical supply track systems for luminaires
EN 60570:2003/A1:2018
EN 60570:2003/A2:2020
263.
EN IEC 60598-1:2021
Luminaires – Part 1: General requirements and tests
EN IEC 60598-1:2021/A11:2022
264.
EN 60598-2-1:1989
Luminaires – Part 2: Particular requirements – Section 1: Fixed general purpose luminaires
265.
EN 60598-2-2:2012
Luminaires – Part 2-2: Particular requirements – Recessed luminaires
266.
EN 60598-2-3:2003
Luminaires – Part 2-3: Particular requirements – Luminaires for road and street lighting
EN 60598-2-3:2003/A1:2011
EN 60598-2-3:2003/AC:2005
267.
EN 60598-2-4:2018
Luminaires – Part 2: Particular requirements – Section 4: Portable general purpose luminaires
268.
EN 60598-2-5:2015
Luminaires – Part 2-5: Particular requirements – Floodlights
269.
EN 60598-2-8:2013
Luminaires – Part 2-8: Particular requirements – Handlamps
270.
EN 60598-2-9:1989
Luminaires – Part 2: Particular requirements – Section 9: Photo and film luminaires (non-professional)
EN 60598-2-9:1989/A1:1994
271.
EN 60598-2-10:2003
Luminaires – Part 2-10: Particular requirements – Portable luminaires for children
EN 60598-2-10:2003/AC:2005
272.
EN 60598-2-11:2013
Luminaires – Part 2-11: Particular requirements – Aquarium luminaires
EN 60598-2-11:2013/A1:2022
273.
EN 60598-2-12:2013
Luminaires – Part 2-12: Particular requirements – Mains socket-outlet mounted nightlights
274.
EN 60598-2-13:2006
Luminaires – Part 2-13: Particular requirements – Ground recessed luminaires
EN 60598-2-13:2006/A1:2012
EN 60598-2-13:2006/AC:2006
EN 60598-2-13:2006/A11:2021
275.
EN 60598-2-14:2009
Luminaires – Part 2-14: Particular requirements – Luminaires for cold cathode tubular discharge lamps (neon tubes) and similar equipment
276.
EN IEC 60598-2-17:2018
Luminaires – Part 2-17: Particular requirements – Luminaires for stage lighting, television and film studios (outdoor and indoor)
277.
EN 60598-2-19:1989
Luminaires – Part 2: Particular requirements – Section 19: Air-handling luminaires (safety requirements)
EN 60598-2-19:1989/A2:1998
EN 60598-2-19:1989/AC:2005
278.
EN 60598-2-20:2015
Luminaires – Part 2-20: Particular requirements – Lighting chains
EN 60598-2-20:2015/AC:2017-01
279.
EN 60598-2-21:2015
Luminaires – Part 2-21: Particular requirements – Rope lights
EN 60598-2-21:2015/AC:2017-01
280.
EN IEC 60598-2-22:2022
Luminaires – Part 2-22: Particular requirements – Luminaires for emergency lighting
281.
EN IEC 60598-2-23:2021
Luminaires – Part 2-23: Particular requirements – Extra-low-voltage lighting systems for ELV light sources
282.
EN 60598-2-24:2013
Luminaires – Part 2-24: Particular requirements – Luminaires with limited surface temperatures
283.
EN 60598-2-25:1994
Luminaires – Part 2-25: Particular requirements – Luminaires for use in clinical areas of hospitals and health care buildings
EN 60598-2-25:1994/A1:2004
284.
EN 60618:1997
Inductive voltage dividers
EN 60618:1997/A2:1997
285.
EN 60645-1:2015
Electroacoustics – Audiometric equipment – Part 1: Equipment for pure-tone audiometry
286.
EN 60645-3:2007
Electroacoustics – Audiometric equipment – Part 3: Test signals of short duration
287.
EN 60645-6:2010
Electroacoustics – Audiometric equipment – Part 6: Instruments for the measurement of otoacoustic emissions
288.
EN 60645-7:2010
Electroacoustics – Audiometric equipment – Part 7: Instruments for the measurement of auditory brainstem responses
289.
EN 60664-1:2007
Insulation coordination for equipment within low-voltage systems – Part 1: Principles, requirements and tests
290.
EN 60664-3:2003
Insulation coordination for equipment within low-voltage systems – Part 3: Use of coating, potting or moulding for protection against pollution
EN 60664-3:2003/A1:2010
291.
EN 60664-4:2006
Insulation coordination for equipment within low-voltage systems – Part 4: Consideration of high-frequency voltage stress
EN 60664-4:2006/AC:2006
292.
EN 60669-1:2018
Switches for household and similar fixed electrical installations – Part 1: General requirements
EN 60669-1:2018/AC:2018-11
EN 60669-1:2018/AC:2020-02
293.
EN 60669-2-1:2004
Switches for household and similar fixed electrical installations – Part 2-1: Particular requirements – Electronic switches
EN 60669-2-1:2004/A1:2009
EN 60669-2-1:2004/A12:2010
EN 60669-2-1:2004/AC:2007
294.
EN 60669-2-2:2006
Switches for household and similar fixed electrical installations – Part 2-2: Particular requirements – Electromagnetic remote-control switches (RCS)
295.
EN 60669-2-3:2006
Switches for household and similar fixed electrical installations – Part 2-3: Particular requirements – Time delay switches (TDS)
296.
EN 60669-2-4:2005
Switches for household and similar fixed electrical installations – Part 2-4: Particular requirements – Isolating switches
297.
EN 60669-2-6:2012
Switches for household and similar fixed electrical installations – Part 2-6: Particular requirements – Fireman’s switches for exterior and interior signs and luminaires
298.
EN IEC 60670-1:2021
Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 1: General requirements
EN IEC 60670-1:2021/A11:2021
299.
EN 60670-21:2007
Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 21: Particular requirements for boxes and enclosures with provision for suspension means
300.
EN 60670-22:2006
Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 22: Particular requirements for connecting boxes and enclosures
301.
EN 60670-23:2008
Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 23: Particular requirements for floor boxes and enclosures
302.
EN 60670-24:2013
Boxes and enclosures for electrical accessories for household and similar fixed electrical installations – Part 24: Particular requirements for enclosures for housing protective devices and other power dissipating electrical equipment
303.
EN 60688:2013
Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals
304.
EN 60691:2016
Thermal-links – Requirements and application guide
EN 60691:2016/A1:2019
305.
EN 60695-2-10:2013
Fire hazard testing – Part 2-10: Glowing/hot-wire based test methods – Glow-wire apparatus and common test procedure
306.
EN 60695-2-11:2014
Fire hazard testing – Part 2-11: Glowing/hot-wire based test methods – Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014)
307.
EN 60695-10-2:2014
Fire hazard testing – Part 10-2: Abnormal heat – Ball pressure test method
308.
EN 60695-10-3:2002
Fire hazard testing – Part 10-3: Abnormal heat – Mould stress relief distortion test
309.
EN 60695-11-2:2014
Fire hazard testing – Part 11-2: Test flames – 1 kW nominal pre-mixed flame: Apparatus, confirmatory test arrangement and guidance
310.
EN 60695-11-3:2012
Fire hazard testing – Part 11-3: Test flames – 500 W flames – Apparatus and confirmational test methods
311.
EN 60695-11-4:2011
Fire hazard testing – Part 11-4: Test flames – 50 W flame – Apparatus and confirmational test method
312.
EN 60695-11-5:2005
Fire hazard testing – Part 11-5: Test flames – Needle-flame test method – Apparatus, confirmatory test arrangement and guidance
313.
EN 60695-11-10:2013
Fire hazard testing – Part 11-10: Test flames – 50 W horizontal and vertical flame test methods
EN 60695-11-10:2013/AC:2014
314.
EN 60695-11-20:2015
Fire hazard testing – Part 11-20: Test flames – 500 W flame test method
EN 60695-11-20:2015/AC:2016
315.
EN 60702-1:2002
Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V – Part 1: Cables
EN 60702-1:2002/A1:2015
316.
EN 60702-2:2002
Mineral insulated cables and their terminations with a rated voltage not exceeding 750 V – Part 2: Terminations
EN 60702-2:2002/A1:2015
317.
EN 60715:2017
Dimensions of low-voltage switchgear and controlgear – Standardized mounting on rails for mechanical support of switchgear, controlgear and accessories
318.
EN 60719:1993
Calculation of the lower and upper limits for the average outer dimensions of cables with circular copper conductors and of rated voltages up to and including 450/750 V
319.
EN 60728-11:2017
Cable networks for television signals, sound signals and interactive services – Part 11: Safety
EN 60728-11:2017/A11:2018
320.
EN 60730-1:2011
Automatic electrical controls for household and similar use – Part 1: General requirements
321.
EN 60730-2-2:2002
Automatic electrical controls for household and similar use – Part 2-2: Particular requirements for thermal motor protectors
EN 60730-2-2:2002/A11:2005
322.
EN 60730-2-3:2007
Automatic electrical controls for household and similar use – Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps
323.
EN 60730-2-4:2007
Automatic electrical controls for household and similar use – Part 2-4: Particular requirements for thermal motor protectors for motor-compressors of hermetic and semi-hermetic type
324.
EN 60730-2-5:2015
Automatic electrical controls – Part 2-5: Particular requirements for automatic electrical burner control systems
325.
EN 60730-2-6:2016
Automatic electrical controls – Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements
326.
EN 60730-2-7:2010
Automatic electrical controls for household and similar use – Part 2-7: Particular requirements for timers and time switches
EN 60730-2-7:2010/AC:2011
327.
EN 60730-2-8:2002
Automatic electrical controls for household and similar use – Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements
EN 60730-2-8:2002/A1:2003
328.
EN 60730-2-9:2010
Automatic electrical controls for household and similar use – Part 2-9: Particular requirements for temperature sensing controls
329.
EN 60730-2-10:2007
Automatic electrical controls for household and similar use – Part 2-10: Particular requirements for motor-starting relays
330.
EN 60730-2-11:2008
Automatic electrical controls for household and similar use – Part 2-11: Particular requirements for energy regulators
331.
EN 60730-2-12:2006
Automatic electrical controls for household and similar use – Part 2-12: Particular requirements for electrically operated door locks
EN 60730-2-12:2006/A11:2008
332.
EN 60730-2-13:2008
Automatic electrical controls for household and similar use – Part 2-13: Particular requirements for humidity sensing controls
333.
EN 60730-2-14:1997
Automatic electrical controls for household and similar use – Part 2-14: Particular requirements for electric actuators
EN 60730-2-14:1997/A11:2005
EN 60730-2-14:1997/A1:2001
EN 60730-2-14:1997/A2:2008
334.
EN 60730-2-15:2010
Automatic electrical controls for household and similar use – Part 2-15: Particular requirements for automatic electrical air flow, water flow and water level sensing controls
335.
EN 60730-2-19:2002
Automatic electrical controls for household and similar use – Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements
EN 60730-2-19:2002/A11:2005
EN 60730-2-19:2002/A2:2008
336.
EN 60799:1998
Electrical accessories – Cord sets and interconnection cord sets
337.
EN 60825-1:2014
Safety of laser products – Part 1: Equipment classification and requirements
EN 60825-1:2014/A11:2021
338.
EN 60825-2:2004
Safety of laser products – Part 2: Safety of optical fibre communication systems (OFCS)
EN 60825-2:2004/A1:2007
EN 60825-2:2004/A2:2010
339.
EN 60825-4:2006
Safety of laser products – Part 4: Laser guards
EN 60825-4:2006/A1:2008
EN 60825-4:2006/A2:2011
340.
EN 60825-12:2004
Safety of laser products – Part 12: Safety of free space optical communication systems used for transmission of information
341.
EN 60831-1:2014
Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 000 V – Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation
EN 60831-1:2014/AC:2014
342.
EN 60831-2:2014
Shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 000 V – Part 2: Ageing test, self-healing test and destruction test
343.
EN 60838-1:2017
Miscellaneous lampholders – Part 1: General requirements and tests
EN 60838-1:2017/A1:2017
EN 60838-1:2017/A11:2021
EN 60838-1:2017/A2:2021
344.
EN 60838-2-1:1996
Miscellaneous lampholders – Part 2: Particular requirements – Section 1: Lampholders S14
EN 60838-2-1:1996/A1:1998
EN 60838-2-1:1996/A2:2004
345.
EN 60838-2-2:2006
Miscellaneous lampholders – Part 2-2: Particular requirements – Connectors for LED-modules
EN 60838-2-2:2006/A1:2012
346.
EN 60898-1:2019
Electrical accessories – Circuit-breakers for overcurrent protection for household and similar installations – Part 1: Circuit-breakers for a.c. operation
347.
EN 60898-2:2021
Electrical accessories – Circuit-breakers for overcurrent protection for household and similar installations – Part 2: Circuit-breakers for a.c. and d.c. operation
348.
EN 60931-1:1996
Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV – Part 1: General – Performance, testing and rating – Safety requirements – Guide for installation and operation
EN 60931-1:1996/A1:2003
349.
EN 60931-2:1996
Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV – Part 2: Ageing test and destruction test
350.
EN 60931-3:1996
Shunt power capacitors of the non-self-healing type for a.c. systems having a rated voltage up to and including 1 kV – Part 3: Internal fuses
351.
EN IEC 60934:2019
Circuit breakers for equipment (CBE)
352.
EN 60947-1:2007
Low-voltage switchgear and controlgear – Part 1: General rules
EN 60947-1:2007/A1:2011
EN 60947-1:2007/A2:2014
353.
EN 60947-2:2017
Low-voltage switchgear and controlgear – Part 2: Circuit-breakers
EN 60947-2:2017/A1:2020
354.
EN IEC 60947-3:2021
Low-voltage switchgear and controlgear – Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units
355.
EN IEC 60947-4-1:2019
Low-voltage switchgear and controlgear – Part 4-1: Contactors and motor-starters – Electromechanical contactors and motor-starters
EN IEC 60947-4-1:2019/AC:2020-05
356.
EN 60947-4-2:2012
Low-voltage switchgear and controlgear – Part 4-2: Contactors and motor-starters – AC semiconductor motor controllers and starters
357.
EN 60947-4-3:2014
Low-voltage switchgear and controlgear – Part 4-3: Contactors and motor-starters – AC semiconductor controllers and contactors for non-motor loads
358.
EN 60947-5-1:2017
Low-voltage switchgear and controlgear – Part 5-1: Control circuit devices and switching elements – Electromechanical control circuit devices
EN 60947-5-1:2017/AC:2020-05
359.
EN IEC 60947-5-2:2020
Low-voltage switchgear and controlgear – Part 5-2: Control circuit devices and switching elements – Proximity switches
360.
EN 60947-5-3:1999
Low-voltage switchgear and controlgear – Part 5-3: Control circuit devices and switching elements – Requirements for proximity devices with defined behaviour under fault conditions (PDF)
EN 60947-5-3:1999/A1:2005
361.
EN 60947-5-4:2003
Low-voltage switchgear and controlgear – Part 5-4: Control circuit devices and switching elements – Method of assessing the performance of low-energy contacts – Special tests
EN 60947-5-4:2003/A1:2019
362.
EN 60947-5-5:1997
Low-voltage switchgear and controlgear – Part 5-5: Control circuit devices and switching elements – Electrical emergency stop device with mechanical latching function
EN 60947-5-5:1997/A1:2005
EN 60947-5-5:1997/A11:2013
EN 60947-5-5:1997/A2:2017
363.
EN 60947-5-7:2003
Low-voltage switchgear and controlgear – Part 5-7: Control circuit devices and switching elements – Requirements for proximity devices with analogue output
364.
EN IEC 60947-5-8:2021
Low-voltage switchgear and controlgear – Part 5-8: Control circuit devices and switching elements – Three-position enabling switches
365.
EN 60947-5-9:2007
Low-voltage switchgear and controlgear – Part 5-9: Control circuit devices and switching elements – Flow rate switches
366.
EN 60947-6-1:2005
Low-voltage switchgear and controlgear – Part 6-1: Multiple function equipment – Transfer switching equipment
EN 60947-6-1:2005/A1:2014
367.
EN 60947-6-2:2003
Low-voltage switchgear and controlgear – Part 6-2: Multiple function equipment – Control and protective switching devices (or equipment) (CPS)
EN 60947-6-2:2003/A1:2007
368.
EN 60947-7-1:2009
Low-voltage switchgear and controlgear – Part 7-1: Ancillary equipment – Terminal blocks for copper conductors
369.
EN 60947-7-2:2009
Low-voltage switchgear and controlgear – Part 7-2: Ancillary equipment – Protective conductor terminal blocks for copper conductors
370.
EN 60947-7-3:2009
Low-voltage switchgear and controlgear – Part 7-3: Ancillary equipment – Safety requirements for fuse terminal blocks
371.
EN 60947-8:2003
Low-voltage switchgear and controlgear – Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines
EN 60947-8:2003/A1:2006
EN 60947-8:2003/A2:2012
372.
EN IEC 60947-9-1:2019
Low-voltage switchgear and controlgear – Part 9-1: Active arc-fault mitigation systems – Arc quenching devices
373.
EN 60950-21:2003 Information technology equipment – Safety – Part 21: Remote power feeding
374.
EN 60950-22:2006
Information technology equipment – Safety – Part 22: Equipment installed outdoors
EN 60950-22:2006/AC:2008
375.
EN 60950-23:2006
Information technology equipment – Safety – Part 23: Large data storage equipment
EN 60950-23:2006/AC:2008
376.
EN 60968:2015
Self-ballasted fluorescent lamps for general lighting services – Safety requirements
377.
EN IEC 60974-1:2018
Arc welding equipment – Part 1: Welding power sources
EN IEC 60974-1:2018/A1:2019
378.
EN IEC 60974-2:2019
Arc welding equipment – Part 2: Liquid cooling systems
379.
EN IEC 60974-3:2019
Arc welding equipment – Part 3: Arc striking and stabilizing devices
380.
EN IEC 60974-5:2019
Arc welding equipment – Part 5: Wire feeders
381.
EN 60974-6:2016
Arc welding equipment – Part 6: Limited duty equipment
382.
EN IEC 60974-7:2019
Arc welding equipment – Part 7: Torches
383.
EN IEC 60974-8:2021
Arc welding equipment – Part 8: Gas consoles for welding and plasma cutting systems
384.
EN IEC 60974-11:2021
Arc welding equipment – Part 11: Electrode holders
385.
EN 60974-12:2011
Arc welding equipment – Part 12: Coupling devices for welding cables
386.
EN IEC 60974-13:2021
Arc welding equipment – Part 13: Welding current return clamp
387.
EN 60998-1:2004
Connecting devices for low-voltage circuits for household and similar purposes – Part 1: General requirements
388.
EN 60998-2-1:2004
Connecting devices for low-voltage circuits for household and similar purposes – Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units
389.
EN 60998-2-2:2004
Connecting devices for low-voltage circuits for household and similar purposes – Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units
390.
EN 60998-2-3:2004
Connecting devices for low-voltage circuits for household and similar purposes – Part 2-3: Particular requirements for connecting devices as separate entities with insulation-piercing clamping units
391.
EN 60998-2-4:2005
Connecting devices for low voltage circuits for household and similar purposes – Part 2-4: Particular requirements for twist-on connecting devices
392.
EN 60999-1:2000
Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units – Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm 2 up to 35 mm 2 (included)
393.
EN 60999-2:2003
Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units – Part 2: Particular requirements for clamping units for conductors above 35 mm 2 up to 300 mm 2 (included)
394.
EN 61008-1:2012
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) – Part 1: General rules
EN 61008-1:2012/A1:2014
EN 61008-1:2012/A11:2015
EN 61008-1:2012/A2:2014
EN 61008-1:2012/A1:2014/AC:2016-06
EN 61008-1:2012/A12:2017
395.
EN 61008-2-1:1994
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB’s) – Part 2-1: Applicability of the general rules to RCCB’s functionally independent of line voltage
EN 61008-2-1:1994/A11:1998
EN 61008-2-1:1994/A11:1998/AC:1999
396.
EN 61009-1:2012
Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) – Part 1: General rules
EN 61009-1:2012/A1:2014
EN 61009-1:2012/A11:2015
EN 61009-1:2012/A2:2014
EN 61009-1:2012/A13:2021
397.
EN 61009-2-1:1994
Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO’s) – Part 2-1: Applicability of the general rules to RCBO’s functionally independent of line voltage
EN 61009-2-1:1994/A11:1998
EN 61009-2-1:1994/A11:1998/AC:1999
398.
EN 61010-1:2010
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 1: General requirements
EN 61010-1:2010/A1:2019/AC:2019-04
EN 61010-1:2010/A1:2019
399.
EN IEC 61010-2-010:2020
Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-010: Particular requirements for laboratory equipment for the heating of materials
400.
EN IEC 61010-2-011:2021
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-011: Particular requirements for refrigerating equipment
EN IEC 61010-2-011:2021/A11:2021
401.
EN IEC 61010-2-012:2022
Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-012: Particular requirements for climatic and environmental testing and other temperature conditioning equipment
EN IEC 61010-2-012:2022/A11:2022
402.
EN 61010-2-020:2006
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-020: Particular requirements for laboratory centrifuges
403.
EN IEC 61010-2-030:2021
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-030: Particular requirements for equipment having testing or measuring circuits
EN IEC 61010-2-030:2021/A11:2021
404.
EN IEC 61010-2-032:2021
Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement
EN IEC 61010-2-032:2021/A11:2021
405.
EN IEC 61010-2-033:2021
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-033: Particular requirements for hand-held multimeters for domestic and professional use, capable of measuring mains voltage
EN IEC 61010-2-033:2021/A11:2021
406.
EN IEC 61010-2-034:2021
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-034: Particular requirements for measurement equipment for insulation resistance and test equipment for electric strength
EN IEC 61010-2-034:2021/A11:2021
407.
EN IEC 61010-2-040:2021
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-040: Particular requirements for sterilizers and washer-disinfectors used to treat medical materials
408.
EN IEC 61010-2-051:2021
Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-051: Particular requirements for laboratory equipment for mixing and stirring
EN IEC 61010-2-051:2021/A11:2021
409.
EN IEC 61010-2-061:2021
Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-061: Particular requirements for laboratory atomic spectrometers with thermal atomization and ionization
EN IEC 61010-2-061:2021/A11:2021
410.
EN IEC 61010-2-081:2020
Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes
411.
EN IEC 61010-2-091:2021
Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-091: Particular requirements for cabinet X-ray systems
EN IEC 61010-2-091:2021/A11:2021
412.
EN IEC 61010-2-130:2021
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-130: Particular requirements for equipment intended to be used in educational establishments by children
413.
EN IEC 61010-2-201:2018
Safety requirements for electrical equipment for measurement, control, and laboratory use – Part 2-201: Particular requirements for control equipment
414.
EN IEC 61010-2-202:2021
Safety requirements for electrical equipment for measurement, control and laboratory use – Part 2-202: Particular requirements for electrically operated valve actuators
415.
EN 61010-031:2015
Safety requirements for electrical equipment for measurement, control and laboratory use – Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test
416.
EN 61028:1993
Electrical measuring instruments – X-Y recorders
EN 61028:1993/A2:1997
417.
EN 61048:2006
Auxiliaries for lamps – Capacitors for use in tubular fluorescent and other discharge lamp circuits – General and safety requirements
EN 61048:2006/A1:2016
418.
EN 61050:1992
Transformers for tubular discharge lamps having a no-load output voltage exceeding 1 kV (generally called neon-transformers) – General and safety requirements
EN 61050:1992/A1:1995
419.
EN IEC 61058-1:2018
Switches for appliances – Part 1: General requirements
420.
EN 61058-2-1:2011
Switches for appliances – Part 2-1: Particular requirements for cord switches
421.
EN 61058-2-4:2005
Switches for appliances – Part 2-4: Particular requirements for independently mounted switches
422.
EN 61058-2-5:2011
Switches for appliances – Part 2-5: Particular requirements for change-over selectors
423.
EN 61071:2007
Capacitors for power electronics
424.
EN 61095:2009
Electromechanical contactors for household and similar purposes
425.
EN 61131-2:2007
Programmable controllers – Part 2: Equipment requirements and tests
426.
EN 61138:2007
Cables for portable earthing and short-circuiting equipment
427.
EN 61140:2002
Protection against electric shock – Common aspects for installation and equipment
EN 61140:2002/A1:2006
428.
EN 61143-1:1994
Electrical measuring instruments – X-t recorders – Part 1: Definitions and requirements
EN 61143-1:1994/A1:1997
429.
EN 61143-2:1994
Electrical measuring instruments – X-t recorders – Part 2: Recommended additional test methods
430.
EN 61184:2017
Bayonet lampholders
431.
EN 61187:1994
Electrical and electronic measuring equipment – Documentation
EN 61187:1994/AC:1995
432.
EN 61195:1999
Double-capped fluorescent lamps – Safety specifications
EN 61195:1999/A1:2013
EN 61195:1999/A2:2015
433.
EN 61199:2011
Single-capped fluorescent lamps – Safety specifications
EN 61199:2011/A1:2013
EN 61199:2011/A2:2015
434.
EN 61204:1995
Low-voltage power supply devices, d.c. output – Performance characteristics
435.
EN IEC 61204-7:2018
Low-voltage switch mode power supplies – Part 7: Safety requirements
436.
EN 61210:2010
Connecting devices – Flat quick-connect terminations for electrical copper conductors – Safety requirements
437.
EN 61230:2008
Live working – Portable equipment for earthing or earthing and short-circuiting
438.
EN 61242:1997
Electrical accessories – Cable reels for household and similar purposes
EN 61242:1997/A1:2008
EN 61242:1997/A2:2016
EN 61242:1997/A1:2008/AC:2010
439.
EN 61243-3:2014
Live working – Voltage detectors – Part 3: Two-pole low-voltage type
EN 61243-3:2014/AC:2015
EN 61243-3:2014/AC:2015
440.
EN 61270-1:1996
Capacitors for microwave ovens – Part 1: General
441.
EN IEC 61293:2020
Marking of electrical equipment with ratings related to electrical supply – Safety requirements
442.
EN 61310-1:2008
Safety of machinery – Indication, marking and actuation – Part 1: Requirements for visual, acoustic and tactile signals
443.
EN 61310-2:2008
Safety of machinery – Indication, marking and actuation – Part 2: Requirements for marking
444.
EN 61310-3:2008
Safety of machinery – Indication, marking and actuation – Part 3: Requirements for the location and operation of actuators
445.
EN 61316:1999
Industrial cable reels
446.
EN 61347-1:2015
Lamp controlgear – Part 1: General and safety requirements
447.
EN 61347-2-2:2012
Lamp controlgear – Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps
448.
EN 61347-2-3:2011
Lamp control gear – Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps
EN 61347-2-3:2011/AC:2011
449.
EN 61347-2-7:2012
Lamp controlgear – Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained)
EN 61347-2-7:2012/A1:2019
EN 61347-2-7:2012/A2:2022
450.
EN 61347-2-8:2001
Lamp controlgear – Part 2-8: Particular requirements for ballasts for fluorescent lamps
EN 61347-2-8:2001/A1:2006
EN 61347-2-8:2001/AC:2003
EN 61347-2-8:2001/AC:2010
451.
EN 61347-2-9:2013
Lamp controlgear – Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps)
452.
EN 61347-2-10:2001
Lamp controlgear – Part 2-10: Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes)
EN 61347-2-10:2001/A1:2009
EN 61347-2-10:2001/AC:2010
453.
EN 61347-2-11:2001
Lamp controlgear – Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires
EN 61347-2-11:2001/AC:2002
EN 61347-2-11:2001/AC:2010
EN 61347-2-11:2001/A1:2019
454.
EN 61347-2-12:2005
Lamp controlgear – Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)
EN 61347-2-12:2005/A1:2010
EN 61347-2-12:2005/AC:2010
455.
EN 61347-2-13:2014
Lamp controlgear – Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules
456.
EN IEC 61347-2-14:2018
Lamp controlgear – Part 2-14: Particular requirements for DC and/or AC supplied electronic controlgear for fluorescent induction lamps
EN IEC 61347-2-14:2018/A11:2021
457.
EN 61386-1:2008
Conduit systems for cable management – Part 1: General requirements
EN 61386-1:2008/A1:2019
458.
EN 61386-21:2004
Conduit systems for cable management – Part 21: Particular requirements – Rigid conduit systems
EN 61386-21:2004/A11:2010
EN 61386-21:2004/AC:2004
459.
EN 61386-22:2004
Conduit systems for cable management – Part 22: Particular requirements – Pliable conduit systems
EN 61386-22:2004/A11:2010
EN 61386-22:2004/AC:2004
460.
EN 61386-23:2004
Conduit systems for cable management – Part 23: Particular requirements – Flexible conduit systems
EN 61386-23:2004/A11:2010
EN 61386-23:2004/AC:2004
461.
EN 61386-24:2010
Conduit systems for cable management – Part 24: Particular requirements – Conduit systems buried underground
462.
EN 61386-25:2011
Conduit systems for cable management – Part 25: Particular requirements – Conduit fixing devices
463.
EN 61439-1:2011
Low-voltage switchgear and controlgear assemblies – Part 1: General rules
464.
EN 61439-2:2011
Low-voltage switchgear and controlgear assemblies – Part 2: Power switchgear and controlgear assemblies
465.
EN 61439-3:2012
Low-voltage switchgear and controlgear assemblies – Part 3: Distribution boards intended to be operated by ordinary persons (DBO)
EN 61439-3:2012/AC:2019-04
466.
EN 61439-4:2013
Low-voltage switchgear and controlgear assemblies – Part 4: Particular requirements for assemblies for construction sites (ACS)
467.
EN 61439-5:2015
Low-voltage switchgear and controlgear assemblies – Part 5: Assemblies for power distribution in public networks
EN 61439-5:2015/AC:2015
468.
EN 61439-6:2012
Low-voltage switchgear and controlgear assemblies – Part 6: Busbar trunking systems (busways)
469.
EN 61534-1:2011
Powertrack systems – Part 1: General requirements
EN 61534-1:2011/A1:2014
EN 61534-1:2011/A11:2021
EN 61534-1:2011/A2:2021
470.
EN 61534-21:2014
Powertrack systems – Part 21: Particular requirements for powertrack systems intended for wall and ceiling mounting
EN 61534-21:2014/A11:2021
471.
EN 61534-22:2014
Powertrack systems – Part 22: Particular requirements for powertrack systems intended for onfloor or underfloor installation
EN 61534-22:2014/A11:2021
472.
EN IEC 61535:2019
Installation couplers intended for permanent connection in fixed installations
473.
EN 61537:2007
Cable management – Cable tray systems and cable ladder systems
474.
EN 61549:2003
Miscellaneous lamps
EN 61549:2003/A3:2012
EN 61549:2003/A1:2005
EN 61549:2003/A2:2010
475.
EN 61557-1:2007
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 1: General requirements
476.
EN 61557-2:2007
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 2: Insulation resistance
477.
EN 61557-3:2007
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 3: Loop impedance
478.
EN 61557-4:2007
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 4: Resistance of earth connection and equipotential bonding
479.
EN 61557-5:2007
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 5: Resistance to earth
480.
EN 61557-6:2007
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems
481.
EN 61557-7:2007
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 7: Phase sequence
482.
EN 61557-8:2015
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 8: Insulation monitoring devices for IT systems
483.
EN 61557-9:2015
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 9: Equipment for insulation fault location in IT systems
EN 61557-9:2015/AC:2017-02
484.
EN 61557-10:2013
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 10: Combined measuring equipment for testing, measuring or monitoring of protective measures
485.
EN 61557-11:2009
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 11: Effectiveness of residual current monitors (RCMs) type A and type B in TT, TN and IT systems
486.
EN IEC 61557-12:2022
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC – Equipment for testing, measuring or monitoring of protective measures – Part 12: Power metering and monitoring devices (PMD)
487.
EN 61557-13:2011
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 13: Hand-held and hand-manipulated current clamps and sensors for measurement of leakage currents in electrical distribution systems
488.
EN 61557-14:2013
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 14: Equipment for testing the safety of electrical equipment of machinery
489.
EN 61557-15:2014
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 15: Functional safety requirements for insulation monitoring devices in IT systems and equipment for insulation fault location in IT systems
490.
EN 61557-16:2015
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 16: Equipment for testing the effectiveness of the protective measures of electrical equipment and/or medical electrical equipment
491.
EN IEC 61558-1:2019
Safety of transformers, reactors, power supply units and combinations thereof – Part 1: General requirements and tests
492.
EN 61558-2-1:2007
Safety of power transformers, power supplies, reactors and similar products – Part 2-1: Particular requirements and tests for separating transformers and power supplies incorporating separating transformers for general applications
493.
EN 61558-2-2:2007
Safety of power transformers, power supplies, reactors and similar products – Part 2-2: Particular requirements and tests for control transformers and power supplies incorporating control transformers
494.
EN 61558-2-3:2010
Safety of transformers, reactors, power supply units and combinations thereof – Part 2-3: Particular requirements and tests for ignition transformers for gas and oil burners
495.
EN 61558-2-4:2009
Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers
496.
EN 61558-2-5:2010
Safety of transformers, reactors, power supply units and combinations thereof – Part 2-5: Particular requirements and tests for transformer for shavers, power supply units for shavers and shaver supply units
497.
EN 61558-2-6:2009
Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
498.
EN 61558-2-7:2007
Safety of power transformers, power supplies, reactors and similar products – Part 2-7: Particular requirements and tests for transformers and power supplies for toys
499.
EN 61558-2-8:2010
Safety of transformers, reactors, power supply units and combinations thereof – Part 2-8: Particular requirements and tests for transformers and power supply units for bells and chimes
500.
EN 61558-2-9:2011
Safety of transformers, reactors, power supply units and combinations thereof – Part 2-9: Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps
501.
EN 61558-2-12:2011
Safety of transformers, reactors, power supply units and combinations thereof – Part 2-12: Particular requirements and tests for constant voltage transformers and power supply units for constant voltage
502.
EN 61558-2-13:2009
Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-13: Particular requirements and tests for auto transformers and power supply units incorporating auto transformers
503.
EN 61558-2-14:2013
Safety of transformers, reactors, power supply units and combination thereof – Part 2-14: Particular requirements and tests for variable transformers and power supply units incorporating variable transformers
504.
EN 61558-2-15:2012
Safety of transformers, reactors, power supply units and combinations thereof – Part 2-15: Particular requirements and tests for isolating transformers for the supply of medical locations
505.
EN 61558-2-16:2009
Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units
EN 61558-2-16:2009/A1:2013
506.
EN 61558-2-20:2011
Safety of transformers, reactors, power supply units and combinations thereof – Part 2-20: Particular requirements and tests for small reactors
507.
EN 61558-2-23:2010
Safety of transformers, reactors, power supply units and combinations thereof – Part 2-23: Particular requirements and tests for transformers and power supply units for construction sites
508.
EN 61558-2-26:2013
Safety of transformers, reactors, power supply units and combinations thereof – Part 2-26: Particular requirements and tests for transformers and power supply units for saving energy and other purposes
509.
EN 61643-11:2012
Low-voltage surge protective devices – Part 11: Surge protective devices connected to low-voltage power systems – Requirements and test methods
EN 61643-11:2012/A11:2018
510.
EN 61643-21:2001
Low voltage surge protective devices – Part 21: Surge protective devices connected to telecommunications and signalling networks – Performance requirements and testing methods
EN 61643-21:2001/A1:2009
EN 61643-21:2001/A2:2013
511.
EN 61643-31:2019
Low-voltage surge protective devices – Part 31: Requirements and test methods for SPDs for photovoltaic installations
512.
EN IEC 61730-1:2018
Photovoltaic (PV) module safety qualification – Part 1: Requirements for construction
EN IEC 61730-1:2018/AC:2018-06
513.
EN IEC 61730-2:2018
Photovoltaic (PV) module safety qualification – Part 2: Requirements for testing
EN IEC 61730-2:2018/AC:2018-06
514.
EN 61770:2009
Electric appliances connected to the water mains – Avoidance of backsiphonage and failure of hose-sets
EN 61770:2009/AC:2011
515.
EN 61800-5-1:2007
Adjustable speed electrical power drive systems – Part 5-1: Safety requirements – Electrical, thermal and energy
EN 61800-5-1:2007/A1:2017
EN 61800-5-1:2007/A11:2021
516.
EN 61812-1:2011
Time relays for industrial and residential use – Part 1: Requirements and tests
517.
EN IEC 61851-1:2019
Electric vehicle conductive charging system – Part 1: General requirements
518.
EN 61851-21:2002
Electric vehicle conductive charging system – Part 21: Electric vehicle requirements for conductive connection to an a.c/d.c. supply
519.
EN 61851-23:2014
Electric vehicle conductive charging system – Part 23: DC electric vehicle charging station
EN 61851-23:2014/AC:2016-06
520.
EN 61851-24:2014
Electric vehicle conductive charging system – Part 24: Digital communication between a d.c. EV charging station and an electric vehicle for control of d.c. charging
EN 61851-24:2014/AC:2015
521.
EN 61869-1:2009
Instrument transformers – Part 1: General requirements
522.
EN 61869-2:2012
Instrument transformers – Part 2: Additional requirements for current transformers
523.
EN 61869-3:2011
Instrument transformers – Part 3: Additional requirements for inductive voltage transformers
524.
EN 61869-4:2014
Instrument transformers – Part 4: Additional requirements for combined transformers
EN 61869-4:2014/AC:2014
525.
EN 61869-5:2011
Instrument transformers – Part 5: Additional requirements for capacitor voltage transformers
EN 61869-5:2011/AC:2015
526.
EN IEC 61914:2021
Cable cleats for electrical installations
527.
EN 61921:2003
Power capacitors – Low-voltage power factor correction banks
528.
EN 61995-1:2008
Devices for the connection of luminaires for household and similar purposes – Part 1: General requirements
EN 61995-1:2008/A1:2017
EN 61995-1:2008/A11:2021
529.
EN 61995-2:2009
Devices for the connection of luminaires for household and similar purposes – Part 2: Standard sheets for DCL
530.
EN 62020:1998
Electrical accessories – Residual current monitors for household and similar uses (RCMs)
EN 62020:1998/A1:2005
531.
EN 62026-1:2007
Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 1: General rules
532.
EN 62026-2:2013
Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 2: Actuator sensor interface (AS-i)
533.
EN 62026-3:2015
Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 3: DeviceNet
EN 62026-3:2015/AC:2019-12
534.
EN 62026-7:2013
Low-voltage switchgear and controlgear – Controller-device interfaces (CDIs) – Part 7: CompoNet
535.
EN IEC 62031:2020
LED modules for general lighting – Safety specifications
EN IEC 62031:2020/A11:2021
536.
EN 62035:2014
Discharge lamps (excluding fluorescent lamps) – Safety specifications
EN 62035:2014/A1:2019
537.
EN IEC 62040-1:2019
Uninterruptible power systems (UPS) – Part 1: Safety requirements
EN IEC 62040-1:2019/A11:2021
538.
EN 62080:2009
Sound signalling devices for household and similar purposes
539.
EN 62094-1:2003
Indicator light units for household and similar fixed-electrical installations – Part 1: General requirements
EN 62094-1:2003/A11:2003
540.
EN 62109-1:2010
Safety of power converters for use in photovoltaic power systems – Part 1: General requirements
541.
EN 62109-2:2011
Safety of power converters for use in photovoltaic power systems – Part 2: Particular requirements for inverters
542.
EN 62135-1:2015
Resistance welding equipment – Part 1: Safety requirements for design, manufacture and installation
EN 62135-1:2015/AC:2016-02
543.
EN 62196-1:2014
Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 1: General requirements
544.
EN 62196-2:2012
Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
EN 62196-2:2012/A12:2014/AC:2014
EN 62196-2:2012/A12:2014
EN 62196-2:2012/A11:2013
545.
EN 62196-3:2014
Plugs, socket-outlets, vehicle connectors and vehicle inlets – Conductive charging of electric vehicles – Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
546.
EN 62208:2011
Empty enclosures for low-voltage switchgear and controlgear assemblies – General requirements
547.
EN 62233:2008
Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure
EN 62233:2008/AC:2008
548.
EN 62253:2011
Photovoltaic pumping systems – Design qualification and performance measurements
549.
EN IEC 62275:2019
Cable management systems – Cable ties for electrical installations
550.
EN 62282-3-100:2012
Fuel cell technologies – Part 3-100: Stationary fuel cell power systems – Safety
551.
EN 62282-3-300:2012
Fuel cell technologies – Part 3-300: Stationary fuel cell power systems – Installation
552.
EN 62282-5-1:2012
Fuel cell technologies – Part 5-1: Portable fuel cell power systems – Safety
553.
EN 62310-1:2005
Static transfer systems (STS) – Part 1: General and safety requirements
554.
EN 62311:2008
Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz – 300 GHz)
555.
EN 62368-1:2014
Audio/video, information and communication technology equipment – Part 1: Safety requirements (IEC 62368-1:2014, modified)
EN 62368-1:2014/AC:2015
556.
EN 62395-1:2013
Electrical resistance trace heating systems for industrial and commercial applications – Part 1: General and testing requirements
557.
EN 62423:2012
Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses
EN 62423:2012/A11:2021
EN 62423:2012/A12:2022
558.
EN 62444:2013
Cable glands for electrical installations
559.
EN 62471:2008
Photobiological safety of lamps and lamp systems
560.
EN 62477-1:2012
Safety requirements for power electronic converter systems and equipment – Part 1: General
EN 62477-1:2012/A11:2014
EN 62477-1:2012/A1:2017
EN 62477-1:2012/A12:2021
561.
EN 62479:2010
Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz)
562.
EN 62493:2010
Assessment of lighting equipment related to human exposure to electromagnetic fields
563.
EN 62532:2011
Fluorescent induction lamps – Safety specifications
564.
EN 62549:2011
Articulated systems and flexible systems for cable guiding
565.
EN 62560:2012
Self-ballasted LED-lamps for general lighting services by voltage > 50 V – Safety specifications
EN 62560:2012/A1:2015
EN 62560:2012/A1:2015/AC:2015
EN 62560:2012/AC:2015
EN 62560:2012/A11:2019
566.
EN 62606:2013
General requirements for arc fault detection devices
EN 62606:2013/A1:2017
567.
EN 62626-1:2014
Low-voltage switchgear and controlgear enclosed equipment – Part 1: Enclosed switch-disconnectors outside the scope of IEC 60947-3 to provide isolation during repair and maintenance work
568.
HD 62640:2015
Residual current devices with or without overcurrent protection for socket-outlets for household and similar uses
569.
EN 62776:2015
Double-capped LED lamps designed to retrofit linear fluorescent lamps – Safety specifications
570.
EN 62868:2015
Organic light emitting diode (OLED) panels for general lighting – Safety requirements
571.
EN 62949:2017
Particular safety requirements for equipment to be connected to information and communication networks
572.
EN 63024:2018
Requirements for automatic reclosing devices (ARDs) for circuit-breakers, RCBOs and RCCBs for household and similar uses
573.
EN IEC 63044-3:2018
Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) – Part 3: Electrical safety requirements
ANNEX II
Reference of the standard
Date of withdrawal
1.
EN 60335-2-24:2010
Household and similar electrical appliances – Safety – Part 2-24: Particular requirements for refrigerating appliances, ice-cream appliances and ice makers
EN 60335-2-24:2010/A1:2019
EN 60335-2-24:2010/A11:2020
EN 60335-2-24:2010/A2:2019
Restriction: For the purposes of presumption of conformity with the corresponding safety objectives, referred to in Article 3 of Directive 2014/35/EU and set out in Annex I to that Directive:
(a)
the text ‘an area exceeding 75 cm2’, in its clause 30.2, shall be read as ‘a total area exceeding 75 cm2 (75 cm2 shall be considered the sum of all holes in back part of an appliance)’;
(b)
the text ‘an area not exceeding 75 cm2’, in its clause 30.2.101, shall be read as ‘a total area not exceeding 75 cm2 (75 cm2 shall be considered the sum of all holes in back part of an appliance).’
13.6.2025
2.
EN 60335-2-30:2009
Household and similar electrical appliances – Safety – Part 2-30: Particular requirements for room heaters
EN 60335-2-30:2009/A11:2012
EN 60335-2-30:2009/AC:2010
EN 60335-2-30:2009/AC:2014
EN 60335-2-30:2009/A1:2020
EN 60335-2-30:2009/A12:2020
17.9.2024
3.
EN 60598-2-22:2014
Luminaires – Part 2-22: Particular requirements – Luminaires for emergency lighting
EN 60598-2-22:2014/AC:2015
EN 60598-2-22:2014/AC:2016-05
EN 60598-2-22:2014/AC:2016-09
EN 60598-2-22:2014/A1:2020
11.7.2024
11.
EN 61347-2-7:2012
Lamp controlgear – Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained)
EN 61347-2-7:2012/A1:2019
11.7.2024
12.
EN 62423:2012
Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses
EN 62423:2012/A11:2021
17.9.2024
ANNEX III
No
Reference of the standard
Date of withdrawal
1.
HD 361 S3:1999
System for cable designation
HD 361 S3:1999/A1:2006,
HD 361 S3:1999/AC:1999
13.6.2025
2.
HD 605 S2:2008
Electric cables – Additional test methods
HD 605 S2:2008/AC:2010
13.6.2025
3.
EN 50363-0:2011
Insulating, sheathing and covering materials for low-voltage energy cables – Part 0: General introduction
13.6.2025
4.
EN 50363-1:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 1: Cross-linked elastomeric insulating compounds
13.6.2025
5.
EN 50363-2-1:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 2-1: Cross-linked elastomeric sheathing compounds
EN 50363-2-1:2005/A1:2011
13.6.2025
6.
EN 50363-2-2:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 2-2: Cross-linked elastomeric covering compounds
13.6.2025
7.
EN 50363-3:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 3: PVC insulating compounds
EN 50363-3:2005/A1:2011
13.6.2025
8.
EN 50363-4-1:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 4-1: PVC sheathing compounds
13.6.2025
9.
EN 50363-4-2:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 4-2: PVC covering compounds
13.6.2025
10.
EN 50363-5:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 5: Halogen-free, cross-linked insulating compounds
EN 50363-5:2005/A1:2011
13.6.2025
11.
EN 50363-6:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 6: Halogen-free, cross-linked sheathing compounds
EN 50363-6:2005/A1:2011
13.6.2025
12.
EN 50363-7:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 7: Halogen-free, thermoplastic insulating compounds
13.6.2025
13.
EN 50363-8:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 8: Halogen-free, thermoplastic sheathing compounds
EN 50363-8:2005/A1:2011
13.6.2025
14.
EN 50363-9-1:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 9-1: Miscellaneous insulating compounds – Cross-linked polyvinyl chloride (XLPVC)
13.6.2025
15.
EN 50363-10-1:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 10-1: Miscellaneous sheathing compounds – Cross-linked polyvinyl chloride (XLPVC)
13.6.2025
16.
EN 50363-10-2:2005
Insulating, sheathing and covering materials for low voltage energy cables – Part 10-2: Miscellaneous sheathing compounds – Thermoplastic polyurethane
13.6.2025
17.
EN 50395:2005
Electrical test methods for low voltage energy cables
EN 50395:2005/A1:2011
13.6.2025
18.
EN 50396:2005
Non electrical test methods for low voltage energy cables
EN 50396:2005/A1:2011
13.6.2025
19.
EN 50497:2007
Recommended test method for assessment of the risk of plasticizer exudation from PVC insulated and sheathed cables
13.6.2025
20.
EN 50565-1:2014
Electric cables – Guide to use for cables with a rated voltage not exceeding 450/750 V (U0/U) – Part 1: General guidance
13.6.2025
21.
EN 50565-2:2014
Electric cables – Guide to use for cables with a rated voltage not exceeding 450/750 V (U0/U) – Part 2: Specific guidance related to EN 50525 cable types
13.6.2025
22.
EN 60228:2005
Conductors of insulated cables
EN 60228:2005/AC:2005
13.6.2025
23.
EN 60332-1-1:2004
Tests on electric and optical fibre cables under fire conditions – Part 1-1: Test for vertical flame propagation for a single insulated wire or cable – Apparatus
EN 60332-1-1:2004/A1:2015
13.6.2025
24.
EN 60332-1-2:2004
Tests on electric and optical fibre cables under fire conditions – Part 1-2: Test for vertical flame propagation for a single insulated wire or cable – Procedure for 1 kW pre-mixed flame
EN 60332-1-2:2004/A1:2015
13.6.2025
25.
EN 60332-1-3:2004
Tests on electric and optical fibre cables under fire conditions – Part 1-3: Test for vertical flame propagation for a single insulated wire or cable – Procedure for determination of flaming droplets/particles
EN 60332-1-3:2004/A1:2015
13.6.2025
26.
EN 60332-2-1:2004
Tests on electric and optical fibre cables under fire conditions – Part 2-1: Test for vertical flame propagation for a single small insulated wire or cable – Apparatus
13.6.2025
27.
EN 60332-2-2:2004
Tests on electric and optical fibre cables under fire conditions – Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame
13.6.2025
28.
EN 60332-3-10:2009
Tests on electric and optical fibre cables under fire conditions – Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables – Apparatus
13.6.2025
29.
EN 60332-3-21:2009
Tests on electric and optical fibre cables under fire conditions – Part 3-21: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A F/R
13.6.2025
30.
EN 60332-3-22:2009
Tests on electric and optical fibre cables under fire conditions – Part 3-22: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category A
13.6.2025
31.
EN 60332-3-23:2009
Tests on electric and optical fibre cables under fire conditions – Part 3-23: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category B
13.6.2025
32.
EN 60332-3-24:2009
Tests on electric and optical fibre cables under fire conditions – Part 3-24: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category C
13.6.2025
33.
EN 60332-3-25:2009
Tests on electric and optical fibre cables under fire conditions – Part 3-25: Test for vertical flame spread of vertically-mounted bunched wires or cables – Category D
13.6.2025
34.
EN 60335-2-11:2010
Household and similar electrical appliances – Safety – Part 2-11: Particular requirements for tumble dryers
EN 60335-2-11:2010/A11:2012
EN 60335-2-11:2010/A1:2015
17.9.2024
35.
EN 60598-1:2015
Luminaires – Part 1: General requirements and tests
EN 60598-1:2015/AC:2015
EN 60598-1:2015/AC:2016
EN 60598-1:2015/AC:2017-05
EN 60598-1:2015/A1:2018
11.7.2024
36.
EN 60598-2-11:2013
Luminaires – Part 2-11: Particular requirements – Aquarium luminaires
17.9.2024
37.
EN 60754-1:2014
Test on gases evolved during combustion of materials from cables – Part 1: Determination of the halogen acid gas content
13.6.2025
38.
EN 60754-2:2014
Test on gases evolved during combustion of materials from cables – Part 2: Determination of acidity (by pH measurement) and conductivity
13.6.2025
39.
EN 60811-100:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 100: General
13.6.2025
40.
EN 60811-201:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 201: General tests – Measurement of insulation thickness
13.6.2025
41.
EN 60811-202:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 202: General tests – Measurement of thickness of non-metallic sheath
13.6.2025
42.
EN 60811-203:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 203: General tests – Measurement of overall dimensions
13.6.2025
43.
EN 60811-301:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 301: Electrical tests – Measurement of the permittivity at 23 °C of filling compounds
13.6.2025
44.
EN 60811-302:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 302: Electrical tests – Measurement of the d.c. resistivity at 23 °C and 100 °C of filling compounds
13.6.2025
45.
EN 60811-401:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 401: Miscellaneous tests – Thermal ageing methods – Ageing in an air oven
13.6.2025
46.
EN 60811-402:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 402: Miscellaneous tests – Water absorption tests
13.6.2025
47.
EN 60811-403:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 403: Miscellaneous tests – Ozone resistance test on cross-linked compounds
13.6.2025
48.
EN 60811-404:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 404: Miscellaneous tests – Mineral oil immersion tests for sheaths
13.6.2025
49.
EN 60811-405:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 405: Miscellaneous tests – Thermal stability test for PVC insulations and PVC sheaths
13.6.2025
50.
EN 60811-406:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 406: Miscellaneous tests – Resistance to stress cracking of polyethylene and polypropylene compounds
13.6.2025
51.
EN 60811-407:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 407: Miscellaneous tests – Measurement of mass increase of polyethylene and polypropylene compounds
13.6.2025
52.
EN 60811-408:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 408: Miscellaneous tests – Long-term stability test of polyethylene and polypropylene compounds
13.6.2025
53.
EN 60811-409:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 409: Miscellaneous tests – Loss of mass test for thermoplastic insulations and sheaths
13.6.2025
54.
EN 60811-410:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 410: Miscellaneous tests – Test method for copper-catalyzed oxidative degradation of polyolefin insulated conductors
13.6.2025
55.
EN 60811-411:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 411: Miscellaneous tests – Low-temperature brittleness of filling compounds
13.6.2025
56.
EN 60811-412:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 412: Miscellaneous tests – Thermal ageing methods – Ageing in an air bomb
13.6.2025
57.
EN 60811-501:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 501: Mechanical tests – Tests for determining the mechanical properties of insulating and sheathing compounds
13.6.2025
58.
EN 60811-502:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 502: Mechanical tests – Shrinkage test for insulations
13.6.2025
59.
EN 60811-503:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 503: Mechanical tests – Shrinkage test for sheaths
13.6.2025
60.
EN 60811-504:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 504: Mechanical tests – Bending tests at low temperature for insulation and sheaths
13.6.2025
61.
EN 60811-505:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 505: Mechanical tests – Elongation at low temperature for insulations and sheaths
13.6.2025
62.
EN 60811-506:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 506: Mechanical tests – Impact test at low temperature for insulations and sheaths
13.6.2025
63.
EN 60811-507:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 507: Mechanical tests – Hot set test for cross-linked materials
13.6.2025
64.
EN 60811-508:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 508: Mechanical tests – Pressure test at high temperature for insulation and sheaths
13.6.2025
65.
EN 60811-509:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 509: Mechanical tests – Test for resistance of insulations and sheaths to cracking (heat shock test)
13.6.2025
66.
EN 60811-510:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 510: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after thermal ageing in air
13.6.2025
67.
EN 60811-511:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 511: Mechanical tests – Measurement of the melt flow index of polyethylene compounds
13.6.2025
68.
EN 60811-512:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 512: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Tensile strength and elongation at break after conditioning at elevated temperature
13.6.2025
69.
EN 60811-513:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 513: Mechanical tests – Methods specific to polyethylene and polypropylene compounds – Wrapping test after conditioning
13.6.2025
70.
EN 60811-601:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 601: Physical tests – Measurement of the drop point of filling compounds
13.6.2025
71.
EN 60811-602:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 602: Physical tests – Separation of oil in filling compounds
13.6.2025
72.
EN 60811-603:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 603: Physical tests – Measurement of total acid number of filling compounds
13.6.2025
73.
EN 60811-604:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 604: Physical tests – Measurement of absence of corrosive components in filling compounds
13.6.2025
74.
EN 60811-605:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 605: Physical tests – Measurement of carbon black and/or mineral filler in polyethylene compounds
13.6.2025
75.
EN 60811-606:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 606: Physical tests – Methods for determining the density#IEC 60811-606:2012
13.6.2025
76.
EN 60811-607:2012
Electric and optical fibre cables – Test methods for non-metallic materials – Part 607: Physical tests – Test for the assessment of carbon black dispersion in polyethylene and polypropylene
13.6.2025
77.
EN 61034-1:2005
Measurement of smoke density of cables burning under defined conditions – Part 1: Test apparatus
EN 61034-1:2005/A1:2014
13.6.2025
78.
EN 61034-2:2005
Measurement of smoke density of cables burning under defined conditions – Part 2: Test procedure and requirements
EN 61034-2:2005/A1:2013
13.6.2025
79.
EN 61557-12:2008
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures – Part 12: Performance measuring and monitoring devices (PMD)
11.7.2024
Commission Implementing Decision (EU) 2023/2723 of 6 December 2023 on harmonised standards for electrical equipment drafted in support of Directive 2014/35/EU of the European Parliament and of the Council (EUR-Lex). Retrieved via LawPlayer, https://lawplayer.com/eu/act/32023D2723
© European Union, https://eur-lex.europa.eu, 1998-2026. Reuse authorised under Commission Decision 2011/833/EU, provided the source is acknowledged.
本頁資料來源：EUR-Lex·整理提供：法律人 LawPlayer· lawplayer.com