Commission Implementing Regulation (EU) 2024/2863 of 12 November 2024 granting a Union authorisation for the biocidal product family Teat disinfectants L-(+)-lactic acid based biocidal product family of Novadan in accordance with Regulation (EU) No 528/2012 of the European Parliament and of the Council

Article 1

A Union authorisation with authorisation number EU-0032465-0000 is hereby granted to ITW Novadan ApS for the making available on the market and use of the biocidal product family ‘Teat disinfectants L-(+)-lactic acid-based biocidal product family of Novadan’ in accordance with the summary of the biocidal product characteristics set out in the Annex. The Union authorisation is valid from 3 December 2024 until 30 November 2034.

Article 2

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union .

SUMMARY OF PRODUCT CHARACTERISTICS FOR A BIOCIDAL PRODUCT FAMILY

ANNEXSupplementary provisions

ANNEX SUMMARY OF PRODUCT CHARACTERISTICS FOR A BIOCIDAL PRODUCT FAMILY Teat disinfectants L-(+)-lactic acid-based biocidal product family of Novadan Product type(s) PT03: Veterinary hygiene Authorisation number: EU-0032465-0000 R4BP asset number: EU-0032465-0000 PART I FIRST INFORMATION LEVEL 1.    ADMINISTRATIVE INFORMATION 1.1.    Family name Name Teat disinfectants L-(+)-lactic acid-based biocidal product family of Novadan 1.2.    Product type(s) Product type(s) PT03: Veterinary hygiene 1.3.    Authorisation holder Name and address of the authorisation holder Name ITW Novadan ApS Address Platinvej 21 6000 Kolding DK Authorisation number   EU-0032465-0000 R4BP asset number   EU-0032465-0000 Date of the authorisation   3 December 2024 Expiry date of the authorisation   30 November 2034 1.4.    Manufacturer(s) of the product Name of manufacturer Novadan ApS Address of manufacturer Platinvej 21, 6000 Kolding, Denmark Location of manufacturing sites Novadan ApS site 1 Platinvej 21, 6000 Kolding, Denmark 1.5.    Manufacturer(s) of the active substance(s) Active substance L-(+)-lactic acid Name of manufacturer Purac Bioquimica SA Address of manufacturer Gran Viral, 19–25, 08160 Montmelo, Spain Location of manufacturing sites Purac Bioquimica SA site 1 Gran Viral, 19–25, 08160 Montmelo, Spain Active substance L-(+)-lactic acid Name of manufacturer Jungbunzlauer S.A. Address of manufacturer Z.I. Portuaire, 67390 Marckolsheim, France Location of manufacturing sites Jungbunzlauer S.A. site 1 Z.I. Portuaire, 67390 Marckolsheim, France 2.    PRODUCT FAMILY COMPOSITION AND FORMULATION 2.1.    Qualitative and quantitative information on the composition of the family Common name IUPAC name Function CAS number EC number Content (%) L-(+)-lactic acid   Active substance 79-33-4 201-196-2 4,1–4,1 % (w/w) 2.2.    Type(s) of formulation Formulation type(s) AL Any other liquid PART II SECOND INFORMATION LEVEL – META SPC(S) 1.    META SPC 1 ADMINISTRATIVE INFORMATION 1.1.    Meta SPC 1 identifier Identifier Meta SPC: meta-SPC 1 1.2.    Suffix to the authorisation number Number 1-1 1.3.    Product type(s) Product type(s) PT03: Veterinary hygiene 2.    META SPC 1 COMPOSITION 2.1.    Qualitative and quantitative information on the composition of the meta SPC 1 Common name IUPAC name Function CAS number EC number Content (%) L-(+)-lactic acid   Active substance 79-33-4 201-196-2 4,1–4,1 % (w/w) 2.2.    Type(s) of formulation of the meta SPC 1 Formulation type(s) AL Any other liquid 3.    HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 1 Hazard statements H318: Causes serious eye damage. Precautionary statements P280: Wear eye protection. P305 + P351 + P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P310: Immediately call a POISON CENTER/doctor. 4.    AUTHORISED USE(S) OF THE META SPC 4.1.    Use description Table 1 Use #1.1: post-milking manual dipping, ready-to-use (RTU) Product type PT03: Veterinary hygiene Where relevant, an exact description of the authorised use Not relevant. Target organism(s) (including development stage) Scientific name: Bacteria Common name: Bacteria Development stage: no data Scientific name: Yeasts Common name: Yeasts Development stage: no data Field(s) of use indoor use Teat disinfection product for dairy animals (cows, buffaloes, sheep, goats) for use after milking. Application method(s) Method: manual dipping Detailed description: Post-milking manual dipping. Application rate(s) and frequency Application rate: Cows and buffaloes: 4 ml/animal per treatment; sheep: 2 ml/animal per treatment; goats: 2-4 ml/animal per treatment. Dilution (%): Ready-to- use (RTU) products formulated to pH = 3 ± 0,1. Not to be diluted. Number and timing of application: Post-milking application 1-3 times per day (apply after every milking). Contact time: 5 minutes. Category(ies) of users professional Pack sizes and packaging material Can, high density polyethylene (HDPE): 0,5, 5, 10, 20, 60 litres Plastic drum, HDPE: 200 litres Intermediate bulk container (IBC), HDPE: 1 000 litres Opaque containers. 4.1.1.    Use-specific instructions Fill the reservoir for the dip cup with the ready-to-use (RTU) product and screw the dip cup on top. Clean the teats carefully by wiping with a single service paper towel or cloth immediately before milking. After milking, squeeze the reservoir and put the dip cup over each teat from below making sure that the full length of the teat is immersed into the disinfectant. Top up with fresh disinfectant by squeezing the reservoir as needed. After disinfection, empty the reservoir and clean reservoir and dip cup by rinsing with water. 4.1.2.    Use-specific risk mitigation measures See general directions for use. 4.1.3.    Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.1.4.    Where specific to the use, the instructions for safe disposal of the product and its packaging See general directions for use. 4.1.5.    Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 4.2.    Use description Table 2 Use #1.4: post-milking automated dipping, ready-to-use (RTU) Product type PT03: Veterinary hygiene Where relevant, an exact description of the authorised use Not relevant. Target organism(s) (including development stage) Scientific name: Bacteria Common name: Bacteria Development stage: no data Scientific name: Yeasts Common name: Yeasts Development stage: no data Field(s) of use indoor use Teat disinfection product for dairy animals (cows, buffaloes, sheep, goats) for use after milking. Application method(s) Method: automated dipping Detailed description: Post-milking automated dipping. Application rate(s) and frequency Application rate: Cows and buffaloes: 4 ml/animal per treatment; sheep: 2 ml/animal per treatment; goats: 2-4 ml/animal per treatment. Dilution (%): Ready-to- use (RTU) products formulated to pH = 3 ± 0,1. Not to be diluted. Number and timing of application: Post-milking application 1-3 times per day (apply after every milking). Contact time: 5 minutes. Category(ies) of users professional Pack sizes and packaging material Can, high density polyethylene (HDPE): 0,5, 5, 10, 20, 60 litres Plastic drum, HDPE: 200 litres Intermediate bulk container (IBC), HDPE: 1 000 litres Opaque containers. 4.2.1.    Use-specific instructions Open the container with the ready-to-use (RTU) product and insert the suction tube of the automated dipping-system. Before milking clean teats carefully by automatic procedure or manually by carefully wiping with a single service paper towel or cloth. After milking, the vacuum is shut off and the teat dip is injected into a manifold on the claw piece. The teats are coated with 2-4 ml of dip when the teat cup is withdrawn by the Automatic Cluster Removal (ACR). The whole process is automated. 4.2.2.    Use-specific risk mitigation measures See general directions for use. 4.2.3.    Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.2.4.    Where specific to the use, the instructions for safe disposal of the product and its packaging See general directions for use. 4.2.5.    Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 5.    GENERAL DIRECTIONS FOR USE OF THE META SPC 1 5.1.    Instructions for use The use of a dosing pump for filling the product into the application equipment is recommended. The product must be brought to temperature above 20  o C before use. To ensure sufficient contact time, care shall be taken that the product is not removed after application. Leave the product until next milking. Keep the animals standing until the product has dried (at least 5 minutes). 5.2.    Risk mitigation measures The following personal protective equipment (PPE) is stipulated without prejudice to the application by employers of Council Directive 98/24/EC and other Union legislation in the area of health and safety at work. The use of eye protection in accordance with the European Standard EN ISO 16321 or equivalent is mandatory during mixing and loading, manual spraying, dipping and cleaning tasks. See section 6 for the full references to legislation and EN standards. Avoid hand to eye transfer. 5.3.    Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment In the case of accident: Contact a doctor or casualty department – take the label or the safety data sheet. Contact a doctor if in doubt about the injured person’s condition or if the symptoms persist. Never give an unconscious person water or other drink. IF INHALED: Move to fresh air and keep at rest in a position comfortable for breathing. If symptoms: Call 112/ambulance for medical assistance. If no symptoms: Call a POISON CENTRE or a doctor IF ON SKIN: Wash skin with water. If symptoms occur call a POISON CENTRE or a doctor. IF IN EYES: Immediately rinse with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing for at least 15 minutes. Call 112/ambulance for medical assistance. IF SWALLOWED: Immediately rinse mouth. Give something to drink, if exposed person is able to swallow. Do NOT induce vomiting. Call 112/ambulance for medical assistance. Environmental emergency measures Avoid discharge to lakes, streams, sewers, etc. Contain and collect spillage with non-combustible, absorbent material e.g., sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations. Wherever possible cleaning should be performed with normal cleaning agents. Avoid use of solvents. 5.4.    Instructions for safe disposal of the product and its packaging Method of disposal: Dispose unused product and the packaging in accordance with local requirements. Used product can be flushed to the municipal sewer or disposed to the manure deposit depending on local requirements. Avoid release to an individual waste water treatment plant. Empty containers are rinsed with plenty of water and disposed in accordance with local requirements. The paper towels used for the cleaning of teats are disposed as mixed municipal waste (European Waste Catalogue (EWC) code 20 03 01). Product is not covered by regulations on dangerous waste. Other information: When handling waste, consideration should be made to the safety precautions applying to handling of the product. 5.5.    Conditions of storage and shelf-life of the product under normal conditions of storage Store in a dry, cool well-ventilated area. Protect from frost. Protect from light. Keep in original container. Keep out of reach of children Shelf-life: 24 months. 6.    OTHER INFORMATION Full references of legislation and EN standards referenced in section 5.2 ‘Risk mitigation measures’: Council Directive 98/24/EC of 7 April 1998 on the protection of the health and safety of workers from the risks related to chemical agents at work (fourteenth individual Directive within the meaning of Article 16(1) of Directive 89/391/EEC) ( OJ L 131, 5.5.1998, p. 11 ). EN ISO 16321 – Eye and face protection for occupational use With respect to the ‘Category(ies) of users’ note: ‘Professionals (including industrial users) means trained professionals if this is required by national legislation.’ 7.    THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 1 7.1.    Trade name(s), authorisation number and specific composition of each individual product Trade name(s) Viri Barriere Dip Market area: EU Agro White Dip Market area: EU Lacto B Dip Market area: EU Authorisation number EU-0032465-0001 1-1   Common name IUPAC name Function CAS number EC number Content (%) L-(+)-lactic acid   Active substance 79-33-4 201-196-2 4,1 % (w/w) 7.2.    Trade name(s), authorisation number and specific composition of each individual product Trade name(s) Viri TE Dip Market area: EU Agro Lac Dip Market area: EU Lacto Extra Dip Market area: EU Authorisation number EU-0032465-0002 1-1   Common name IUPAC name Function CAS number EC number Content (%) L-(+)-lactic acid   Active substance 79-33-4 201-196-2 4,1 % (w/w) 7.3.    Trade name(s), authorisation number and specific composition of each individual product Trade name(s) Nova FD Market area: EU Agro FD Market area: EU Lacto FD Market area: EU DF CUA Market area: EU Lacto Protect Film Market area: EU Authorisation number EU-0032465-0003 1-1   Common name IUPAC name Function CAS number EC number Content (%) L-(+)-lactic acid   Active substance 79-33-4 201-196-2 4,1 % (w/w) 1.    META SPC 2 ADMINISTRATIVE INFORMATION 1.1.    Meta SPC 2 identifier Identifier Meta SPC: meta-SPC 2 1.2.    Suffix to the authorisation number Number 1-2 1.3.    Product type(s) Product type(s) PT03: Veterinary hygiene 2.    META SPC 2 COMPOSITION 2.1.    Qualitative and quantitative information on the composition of the meta SPC 2 Common name IUPAC name Function CAS number EC number Content (%) L-(+)-lactic acid   Active substance 79-33-4 201-196-2 4,1–4,1 % (w/w) 2.2.    Type(s) of formulation of the meta SPC 2 Formulation type(s) AL Any other liquid 3.    HAZARD AND PRECAUTIONARY STATEMENTS OF THE META SPC 2 Hazard statements H318: Causes serious eye damage. Precautionary statements P280: Wear eye protection. P305 + P351 + P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P310: Immediately call a POISON CENTER/doctor. 4.    AUTHORISED USE(S) OF THE META SPC 4.1.    Use description Table 1 Use #1.1: post-milking manual dipping, ready-to-use (RTU) Product type PT03: Veterinary hygiene Where relevant, an exact description of the authorised use Not relevant. Target organism(s) (including development stage) Scientific name: Bacteria Common name: Bacteria Development stage: no data Scientific name: Yeasts Common name: Yeasts Development stage: no data Field(s) of use indoor use Teat disinfection product for dairy animals (cows, buffaloes, sheep, goats) for use after milking. Application method(s) Method: manual dipping Detailed description: Post-milking manual dipping. Application rate(s) and frequency Application rate: Cows and buffaloes: 4 ml/animal per treatment; sheep: 2 ml/animal per treatment; goats: 2-4 ml/animal per treatment. Dilution (%): Ready-to- use (RTU) products formulated to pH = 3 ± 0,1. Not to be diluted. Number and timing of application: Post-milking application 1-3 times per day (apply after every milking). Contact time: 5 minutes. Category(ies) of users professional Pack sizes and packaging material Can, high density polyethylene (HDPE): 0,5, 5, 10, 20, 60 litres Plastic drum, HDPE: 200 litres Intermediate bulk container (IBC), HDPE: 1 000 litres Opaque containers. 4.1.1.    Use-specific instructions Fill the reservoir for the dip cup with the ready-to-use (RTU) product and screw the dip cup on top. Clean the teats carefully by wiping with a single service paper towel or cloth immediately before milking. After milking, squeeze the reservoir and put the dip cup over each teat from below making sure that the full length of the teat is immersed into the disinfectant. Top up with fresh disinfectant by squeezing the reservoir as needed. After disinfection, empty the reservoir and clean reservoir and dip cup by rinsing with water. 4.1.2.    Use-specific risk mitigation measures See general directions for use. 4.1.3.    Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.1.4.    Where specific to the use, the instructions for safe disposal of the product and its packaging See general directions for use. 4.1.5.    Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 4.2.    Use description Table 2 Use #1.2 post-milking, manual spraying using a trigger sprayer, ready-to-use (RTU) Product type PT03: Veterinary hygiene Where relevant, an exact description of the authorised use Not relevant. Target organism(s) (including development stage) Scientific name: Bacteria Common name: Bacteria Development stage: no data Scientific name: Yeasts Common name: Yeasts Development stage: no data Field(s) of use indoor use Teat disinfection product for dairy animals (cows, buffaloes, sheep, goats) for use after milking. Application method(s) Method: manual spraying, trigger sprayer Detailed description: Post-milking manual using a trigger sprayer Application rate(s) and frequency Application rate: Cows and buffaloes: 4 ml/animal per treatment; sheep: 2 ml/animal per treatment; goats: 2-4 ml/animal per treatment. Dilution (%): Ready-to- use (RTU) products formulated to pH = 3 ± 0,1. Not to be diluted. Number and timing of application: Post-milking application 1-3 times per day (apply after every milking). Contact time: 5 minutes. Category(ies) of users professional Pack sizes and packaging material Can, high density polyethylene (HDPE): 0,5, 5, 10, 20, 60 litres Plastic drum, HDPE: 200 litres Intermediate bulk container (IBC), HDPE: 1 000 litres Opaque containers. 4.2.1.    Use-specific instructions Fill the reservoir with the ready-to-use (RTU) product and screw the top of the trigger sprayer on it. Clean the teats carefully by wiping with a single service paper towel or cloth immediately before milking. After milking, spray the disinfectant on the teats using the trigger sprayer making sure that each teat is covered with the disinfectant. Top up the reservoir with fresh disinfectant as needed. After disinfection, empty the reservoir and clean reservoir and trigger sprayer by rinsing with water. 4.2.2.    Use-specific risk mitigation measures See general directions for use. The professional bystander must wear the same personal protective equipment (PPE) as the professional user. 4.2.3.    Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.2.4.    Where specific to the use, the instructions for safe disposal of the product and its packaging See general directions for use. 4.2.5.    Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 4.3.    Use description Table 3 Use #1.3 post-milking manual spraying using an electronic sprayer, ready-to-use (RTU) Product type PT03: Veterinary hygiene Where relevant, an exact description of the authorised use Not relevant. Target organism(s) (including development stage) Scientific name: Bacteria Common name: Bacteria Development stage: no data Scientific name: Yeasts Common name: Yeasts Development stage: no data Field(s) of use indoor use Teat disinfection product for dairy animals (cows, buffaloes, sheep, goats) for use after milking. Application method(s) Method: Manual spraying with electronic sprayer Detailed description: Post-milking manual with electronic sprayer. Application rate(s) and frequency Application rate: Cows and buffaloes: 4 ml/animal per treatment; sheep: 2 ml/animal per treatment; goats: 2-4 ml/animal per treatment. Dilution (%): Ready-to- use (RTU) products formulated to pH = 3 ± 0,1. Not to be diluted. Number and timing of application: Post-milking application 1-3 times per day (apply after every milking). Contact time: 5 minutes. Category(ies) of users professional Pack sizes and packaging material Can, high density polyethylene (HDPE): 0,5, 5, 10, 20, 60 litres Plastic drum, HDPE: 200 litres Intermediate bulk container (IBC), HDPE: 1 000 litres Opaque containers. 4.3.1.    Use-specific instructions Open the container with the ready -to-use (RTU) product and insert the suction tube of the electronic sprayer. Clean the teats carefully by wiping with a single service paper towel or cloth immediately before milking. After milking, spray the disinfectant on the teats using the electronic sprayer making sure that each teat is covered with the disinfectant. Replace the empty container by a new one as needed.After disinfection, put the suction tube system into a bucket of water and rinse the sprayer by pumping the water through the sprayer. 4.3.2.    Use-specific risk mitigation measures See general directions for use. The professional bystander must wear the same personal protective equipment (PPE) as the professional user. 4.3.3.    Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.3.4.    Where specific to the use, the instructions for safe disposal of the product and its packaging See general directions for use. 4.3.5.    Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 4.4.    Use description Table 4 Use #1.4: post-milking automated dipping, ready-to-use (RTU) Product type PT03: Veterinary hygiene Where relevant, an exact description of the authorised use Not relevant. Target organism(s) (including development stage) Scientific name: Bacteria Common name: Bacteria Development stage: no data Scientific name: Yeasts Common name: Yeasts Development stage: no data Field(s) of use indoor use Teat disinfection product for dairy animals (cows, buffaloes, sheep, goats) for use after milking. Application method(s) Method: automated dipping Detailed description: Post-milking automated dipping. Application rate(s) and frequency Application rate: Cows and buffaloes: 4 ml/animal per treatment; sheep: 2 ml/animal per treatment; goats: 2-4 ml/animal per treatment. Dilution (%): Ready-to- use (RTU) products formulated to pH = 3 ± 0,1. Not to be diluted. Number and timing of application: Post-milking application 1-3 times per day (apply after every milking). Contact time: 5 minutes. Category(ies) of users professional Pack sizes and packaging material Can, high density polyethylene (HDPE): 0,5, 5, 10, 20, 60 litres Plastic drum, HDPE: 200 litres Intermediate bulk container (IBC), HDPE: 1 000 litres Opaque containers. 4.4.1.    Use-specific instructions Open the container with the ready-to-use (RTU) product and insert the suction tube of the automated dipping-system. Before milking clean teats carefully by automatic procedure or manually by carefully wiping with a single service paper towel or cloth. After milking, the vacuum is shut off and the teat dip is injected into a manifold on the claw piece. The teats are coated with 2-4 ml of dip when the teat cup is withdrawn by the Automatic Cluster Removal (ACR). The whole process is automated. 4.4.2.    Use-specific risk mitigation measures See general directions for use. 4.4.3.    Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.4.4.    Where specific to the use, the instructions for safe disposal of the product and its packaging See general directions for use. 4.4.5.    Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 4.5.    Use description Table 5 Use # 1.5: post-milking automated spraying by robot, ready-to-use (RTU) Product type PT03: Veterinary hygiene Where relevant, an exact description of the authorised use Not relevant. Target organism(s) (including development stage) Scientific name: Bacteria Common name: Bacteria Development stage: no data Scientific name: Yeasts Common name: Yeasts Development stage: no data Field(s) of use indoor use Teat disinfection product for dairy animals (cows, buffaloes, sheep, goats) for use after milking. Application method(s) Method: automated spraying by robot Detailed description: Post-milking automated spraying by robot. Application rate(s) and frequency Application rate: Cows and buffaloes: 4 ml/animal per treatment; sheep: 2 ml/animal per treatment; goats: 2-4 ml/animal per treatment. Dilution (%): Ready-to- use (RTU) products formulated to pH = 3 ± 0,1. Not to be diluted. Number and timing of application: Post-milking application 1-3 times per day (apply after every milking). Contact time: 5 minutes. Category(ies) of users professional Pack sizes and packaging material Can, high density polyethylene (HDPE): 0,5, 5, 10, 20, 60 litres Plastic drum, HDPE: 200 litres Intermediate bulk container (IBC), HDPE: 1 000 litres Opaque containers. 4.5.1.    Use-specific instructions Open the container with the ready-to-use (RTU) product and insert the suction tube of the robotic milking device. The teats are cleaned by robot with automatic brushes. After robotic milking, 2-4 ml of the disinfectant is sprayed automatically onto teats from a cluster arm. Rinsing of the sprayer is automatic. 4.5.2.    Use-specific risk mitigation measures See general directions for use. 4.5.3.    Where specific to the use, the particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment See general directions for use. 4.5.4.    Where specific to the use, the instructions for safe disposal of the product and its packaging See general directions for use. 4.5.5.    Where specific to the use, the conditions of storage and shelf-life of the product under normal conditions of storage See general directions for use. 5.    GENERAL DIRECTIONS FOR USE OF THE META SPC 2 5.1.    Instructions for use The use of a dosing pump for filling the product into the application equipment is recommended. The product must be brought to temperature above 20  o C before use. To ensure sufficient contact time, care shall be taken that the product is not removed after application. Leave the product until next milking. Keep the animals standing until the product has dried (at least 5 minutes). 5.2.    Risk mitigation measures The following personal protective equipment (PPE) is stipulated without prejudice to the application by employers of Council Directive 98/24/EC and other Union legislation in the area of health and safety at work. The use of eye protection in accordance with the European Standard EN ISO 16321 or equivalent is mandatory during mixing and loading, manual spraying, dipping and cleaning tasks. See section 6 for the full references to legislation and EN standards. Avoid hand to eye transfer. 5.3.    Particulars of likely direct or indirect effects, first aid instructions and emergency measures to protect the environment In the case of accident: Contact a doctor or casualty department – take the label or this safety data sheet. Contact a doctor if in doubt about the injured person’s condition or if the symptoms persist. Never give an unconscious person water or other drink. IF INHALED: Move to fresh air and keep at rest in a position comfortable for breathing. If symptoms: Call 112/ambulance for medical assistance. If no symptoms: Call a POISON CENTRE or a doctor IF ON SKIN: Wash skin with water. If symptoms occur call a POISON CENTRE or a doctor. IF IN EYES: Immediately rinse with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing for at least 15 minutes. Call 112/ambulance for medical assistance. IF SWALLOWED: Immediately rinse mouth. Give something to drink, if exposed person is able to swallow. Do NOT induce vomiting. Call 112/ambulance for medical assistance. Environmental emergency measures Avoid discharge to lakes, streams, sewers, etc. Contain and collect spillage with non-combustible, absorbent material e.g., sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations. Wherever possible cleaning should be performed with normal cleaning agents. Avoid use of solvents. 5.4.    Instructions for safe disposal of the product and its packaging Method of disposal: Dispose unused product and the packaging in accordance with local requirements. Used product can be flushed to the municipal sewer or disposed to the manure deposit depending on local requirements. Avoid release to an individual waste water treatment plant. Empty containers are rinsed with plenty of water and disposed in accordance with local requirements. The paper towels used for the cleaning of teats are disposed as mixed municipal waste (European Waste Catalogue (EWC) code 20 03 01). Product is not covered by regulations on dangerous waste. Other information: When handling waste, consideration should be made to the safety precautions applying to handling of the product. 5.5.    Conditions of storage and shelf-life of the product under normal conditions of storage Store in a dry, cool well-ventilated area. Protect from frost. Protect from light. Keep in original container. Keep out of reach of children Shelf-life: 24 months. 6.    OTHER INFORMATION Full references of legislation and EN standards referenced in section 5.2 ‘Risk mitigation measures’: Council Directive 98/24/EC of 7 April 1998 on the protection of the health and safety of workers from the risks related to chemical agents at work (fourteenth individual Directive within the meaning of Article 16(1) of Directive 89/391/EEC) ( OJ L 131, 5.5.1998, p. 11 ). EN ISO 16321 – Eye and face protection for occupational use With respect to the ‘Category(ies) of users’ note: ‘Professionals (including industrial users) means trained professionals if this is required by national legislation.’ 7.    THIRD INFORMATION LEVEL: INDIVIDUAL PRODUCTS IN THE META SPC 2 7.1.    Trade name(s), authorisation number and specific composition of each individual product Trade name(s) Viri TE Spray Market area: EU Agro Lac Spray Market area: EU Lacto Extra Spray Market area: EU LactoPlus Market area: EU Teho Lacta Spray Market area: EU Authorisation number EU-0032465-0004 1-2   Common name IUPAC name Function CAS number EC number Content (%) L-(+)-lactic acid   Active substance 79-33-4 201-196-2 4,1 % (w/w) 7.2.    Trade name(s), authorisation number and specific composition of each individual product Trade name(s) Nova LA Spray Market area: EU Agro LA Spray Market area: EU Lacto LA Spray Market area: EU Lacto Max Market area: EU Lacto Protect Sprüh Market area: EU Authorisation number EU-0032465-0005 1-2   Common name IUPAC name Function CAS number EC number Content (%) L-(+)-lactic acid   Active substance 79-33-4 201-196-2 4,1 % (w/w)