Commission Implementing Regulation (EU) 2015/504 ANNEX I

ANNEX ISupplementary provisions

ANNEX I Template for the information document and for the information folder List of Appendices Appendix Number Appendix title Page 1 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of an engine/engine family system 64 2 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an external sound level system 75 3 Model information document relating to EU type-approval of an engine/engine family as a component/STU 78 4 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a driver information system 89 5 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of lighting and light-signalling devices system 90 6 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an electro-magnetic compatibility system 92 7 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of audible warning device(s) system 93 8 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of rear-view mirror as a system 94 9 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of a crawler undercarriage system 96 10 Model information document relating to EU type-approval of electro-magnetic compatibility of electrical/electronic sub-assemblies as a STU 100 11 Model information document relating to EU type-approval of ballast masses as a component/STU 101 12 Model information document relating to EU type-approval of a lateral and/or rear protective structure as a component/STU 102 13 Model information document relating to EU type-approval of a tyre as a component 103 14 Model information document relating to EU type-approval of a mechanical coupling as a component/STU 104 15 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a braking system 106 16 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a driver's exposure to noise level system 113 17 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a seat-belt anchorages system 114 18 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a protection against hazardous substances system 117 19 Model information document relating to EU type-approval of a roll-over protective structure (ROPS) as a STU 118 20 Model information document relating to EU type-approval of a falling objects protective structure (FOPS) as a STU 121 21 Model information document relating to EU type-approval of a driver's seat as a component/STU 123 22 Model information document relating to EU type-approval of a safety belt as a component/STU 125 23 Model information document relating to EU type-approval of a protection against penetrating objects (OPS) as a STU 127 24 Manufacturer's declaration on anti-tampering of powertrain and speed-limitation device 128 PART A INFORMATION FOLDER 1.    General requirements 1.1.   When applying for EU type-approval for a vehicle, system, component or separate technical unit, the manufacturer shall provide, in accordance with Article 22 of Regulation (EU) No 167/2013, an information folder which shall contain the following: (a) a list of contents; (b) the information on the type-approval procedure chosen in accordance with Article 20(1) of Regulation (EU) No 167/2013, the template for which is set out in point 2 (information folder sheet); (c) the information document as set out in Part B of this Annex; (d) all relevant data, drawings, photographs and other information as required in the information document; (e) the manufacturer's certificate providing proof of compliance to the type-approval authority on access to vehicle on-board diagnostic (OBD) and to vehicle repair and maintenance information as referred to in Article 53(8) of Regulation (EU) No 167/2013 and set out in Annex II to this Regulation; (f) for tractors type-approved with machinery mounted on them and for R- and S-category vehicles, a document setting out the contents of the EC declaration of conformity in accordance with the national provisions implementing Directive 2006/42/EC of the European Parliament and of the Council, not necessarily including the serial number and the signature; if requested by the approval authority, the manufacturer shall provide in addition any relevant documentation contained in the technical file of the machinery set out in Annex VII to that Directive, especially: — the standards and other technical specifications used, indicating the essential health and safety requirements covered by these standards, — any technical report giving the results of the tests carried out either by the manufacturer or by a body chosen by the manufacturer or his authorised representative; (g) any additional information requested by the approval authority as part of the approval procedure. (h) the manufacturer's declaration on anti-tampering of powertrain and speed-limitation device as referred to in Article 17(2)(b) of Regulation (EU) No 167/2013 and in point 4.3.2 of Annex III to Commission Delegated Regulation (EU) 2015/208  ( 1 ) according to the model established in Appendix 24 to this Annex; (i) For vehicles equipped with (an) electrical/electronic device(s) which limit its propulsion performance, data and evidence to demonstrate that modification or disconnection of the device or its wiring system will not increase the propulsion performance. 1.2.   Applications submitted on paper shall be in triplicate. Any drawings shall be to an appropriate scale and in sufficient detail on size A4 sheets or in a folder of A4 format. Photographs (if any) shall show sufficient detail. 1.3.   Information concerning the performance of complex electronic vehicle control systems listed in Appendix 2 to Annex XXIII to Commission Delegated Regulation (EU) No 1322/2014  ( 2 ) shall be provided. 2.    Template of the information folder sheet. Information on the type-approval procedure chosen in accordance with Article 20(1) of Regulation (EU) No 167/2013 of the European Parliament and of the Council Information folder sheet A duly completed version of this statement shall be included in the information folder. The undersigned: […(full name and position)] Company name and address of the manufacturer ( 4 ): … Name and address of the manufacturer's representative (if any) ( 4 ): … Hereby applies for type-approval procedure: (a) step-by-step type-approval ( 1 ) (b) single-step type-approval ( 1 ) (c) mixed type-approval ( 1 ) Where procedures (a) or (c) are chosen, compliance with requirements as under (b) is declared for all systems, components and separate technical units. Multi-stage type-approval chosen in accordance with Article 20(5) of Regulation (EU) No 167/2013: yes/no ( 1 ) Information on the vehicle(s) to be filled in, if application is for EU whole-vehicle type-approval: 1.1   Make (trade name of the manufacturer) ( 4 ): … 1.2.   Type ( 2 ): … 1.2.1.   Variant(s) ( 2 ): … 1.2.2.   Version(s) ( 2 ): … 1.2.3   Commercial name(s) (if available): … 1.2.4.   Type-approval number(s) of the previous stage(s) ( 4 ): … 1.3.   Category, subcategory and speed index of the vehicle ( 3 ): … Applies for type-approval of: (a) a complete vehicle type ( 1 ) (b) completed vehicle type ( 1 ) (c) an incomplete vehicle type ( 1 ) (d) a vehicle type with complete and incomplete variants ( 1 ) (e) a vehicle type with completed and incomplete variants ( 1 ) Information to be filled in, if application is for type-approval of a system/component/separate technical unit ( 1 ) : 2.1.   Make(s) (trade name(s) of manufacturer): … 2.2.   Type ( 5 ): … 2.2.1.   Commercial name(s) (if available): … 2.5.2.   Manufacturer's type coding (as marked on the engine or other means of identification): … ( 1 ): … 2.8.   Virtual and/or self-testing ( 1 ) 2.8.1.   Overview list with virtual and/or self-tested systems, components or separate technical units pursuant to Article 27(4) and Article 60 of Regulation (EU) No 167/2013: Overview table virtual and/or self-testing Delegated act reference Annex No Requirement Restrictions/Comments         2.8.2.   Detailed report on validation of virtual and/or self-testing added: yes/no ( 1 ) Place: … Date: … Signature: … Name and position in the company: … Explanatory notes relating to the information folder sheet (Footnote markers, footnotes and explanatory notes not to be stated on the information folder sheet) (1) Delete if not applicable. (2) Indicate the alphanumeric code Type-Variant-Version or ‘TVV’ allocated to each type, variant and version as set out in point 2.3 of Part B of Annex I to this Regulation. For the identification of variant and versions it may be employed the matrix set out in point 2.2 of Part B of Annex I to this Regulation. (3) Classified according to Article 4 of Regulation (EU) No 167/2013, the coding shall be indicated, e.g. ‘T4.3a’ for a low-clearance tractor with a maximum design speed below or equal to 40 km/h. (4) In case of multi-stage type-approval supply this information for each stage(s). (5) For engines indicate the information relative to the engine type or the engine family type, as applicable. PART B INFORMATION DOCUMENT 1.   GENERAL REQUIREMENTS 1.1.   The information document shall have a reference number supplied by the applicant. 1.2.   Where the particulars appearing in the information document for vehicle approval have changed, the manufacturer shall submit revised pages to the approval authority showing clearly the nature of the change(s) and the date of re-issue. 2.   TYPE-APPROVAL OF VEHICLES 2.1.   All information documents shall contain the following: — the matrix in point 2.2 to identify the versions and variants of the vehicle intended for type-approval, — a list of items applicable to the (sub-)category and to the technical characteristics of the vehicle from which content has been extracted, adhering to the numbering system of the total list set out in point 5. 2.2.   Matrix showing the combinations of the entries listed in point 5 within the versions and variants of the vehicle type Variants and version matrix Item No All Version 1 Version 2 Version 3 Version n             2.2.1.   A separate matrix shall be compiled for each variant within the type. 2.2.2.   Entries with no restrictions on their combination within a variant shall be listed in the column headed ‘All’. 2.2.3.   The above information may be presented in an alternative format or merged with the information supplied under point 5. 2.3   Type-, variant- and version designations 2.3.1.   The manufacturer shall allocate an alphanumeric code to each vehicle type, variant and version, made up of Roman letters and/or Arabic numerals, which shall also be indicated in the certificate of conformity (see Annex III) of the vehicle concerned. The use of brackets and hyphens is permitted provided they do not replace a letter or a numeral. 2.3.2.   The whole code shall be designated: Type-Variant-Version or ‘TVV’. 2.3.3.   The TVV shall clearly and unequivocally identify a unique combination of technical features in relation to the criteria defined in Part B of this Annex. 2.3.4.   The same manufacturer may use the same code in order to define a vehicle type when the latter falls in two or more categories. 2.3.5.   The same manufacturer shall not use the same code in order to define a vehicle type for more than one type-approval within the same vehicle category. 2.3.6.   Number of characters for the TVV 2.3.6.1. The number of characters shall not exceed: (a) 15 for the code of the vehicle type; (b) 25 for the code of one variant; (c) 35 for the code of one version. 2.3.6.2. The complete alphanumeric ‘TVV’ shall not contain more than 75 characters. 2.3.6.3. When the TVV is used as a whole, a space shall be left between the type, the variant and the version. Example of such TVV: 159AF[… space]0054[… space]977K(BE). 3.   TYPE-APPROVAL OF SYSTEMS, COMPONENTS AND SEPARATE TECHNICAL UNITS 3.1.   For a system, component or separate technical unit as listed in Table 1-1 the manufacturer shall complete the applicable appendix to this Annex. In addition to the Annexes mentioned in Table 1-1, the systems, components and separate technical units shall comply with the following requirements: (a) arrangements for type-approval procedures (Annex III to Commission Delegated Regulation (EU) No 1322/2014) (b) conformity of production (CoP) (Annex IV to Commission Delegated Regulation (EU) No 1322/2014)) (c) access to repair and maintenance information (Annex V to Commission Delegated Regulation (EU) No 1322/2014) Table 1-1 Lists of systems, components and separate technical units which may be subject to an EU type-approval LIST I — Environmental and propulsion unit performance requirements Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) 2015/96  ( 3 ) Annex number As amended by and/or at the stage of implementation 1 System: installation of an engine/engine family II   2 System: external sound level III   3 Component/STU: engine/engine family I   LIST II — Vehicle functional safety requirements Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) 2015/208 Annex number As amended by and/or at the stage of implementation 4 System: driver information X   5 System: installation of lighting and light-signalling devices XII   6 System: electro-magnetic compatibility XV   12 System: installation of audible warning device(s) XVI   9 System: installation of rear-view mirrors IX   8 System: installation of crawler undercarriage XXXIII   10 STU: electro-magnetic compatibility of electrical/electronic sub-assemblies XV   11 Component/STU: ballast masses XXIII   12 Component/STU: lateral and/or rear protective structure XXVI   13 Component: tyre XXX   14 Component/STU: mechanical coupling XXXIV   LIST III — Vehicle braking requirements Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) 2015/68  ( 4 ) Annex number As amended by and/or at the stage of implementation 15 System: braking II   LIST IV — Vehicle construction and general type-approval requirements Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) No 1322/2014 Annex number As amended by and/or at the stage of implementation 17 System: driver's exposure to noise level XIII   18 System: seat-belt anchorages XVIII   19 System: protection against hazardous substances XXIX   20 STU: roll-over protective structure (ROPS) VI/VII/VIII/IX/X   21 STU: falling objects protective structure (FOPS) XI   22 Component/STU: driver's seat XIV   23 Component/STU: safety belts XIX   24 STU: protection against penetrating objects (OPS) XX   4.   TYPE-APPROVAL NUMBERS OR TEST REPORTS NUMBERS OF THE APPLICABLE SUBJECTS 4.1.   The manufacturer shall supply the information required by Table 1-2 in respect of the applicable subjects for the vehicle set out in Annex I to Regulation (EU) No 167/2013. All relevant approvals and test reports (if available) for each subject shall be included. However, information in respect of systems, components or separate technical units need not be given here so long as such information is included in the correspondent approval certificate. Table 1-2 Type-approval number and test report overview Item number and subject Type-approval number or test report number  ( *3 ) Date of issue of the type-approval or of its extension or of the test report Member State or contracting party  ( *1 ) issuing the type-approval  ( *2 ) or technical service issuing the test report  ( *3 ) Reference to the regulatory act and its latest amendment Variant(s)/version(s) e.g. ‘36 ROPS (track laid)’                       Signed: … Position in company: … Date: … 4.2.   For those subjects referred to in Annex I to Regulation (EU) No 167/2013 whose approvals have been granted in accordance with Directive 97/68/EC, Regulation (EC) No 595/2009 or the UNECE regulations referred to in Article 49 of Regulation (EU) No 167/2013 (UNECE approvals), or are based on complete test reports issued on the basis of the OECD standard Codes as an alternative to the test reports drawn up under that Regulation and the delegated acts adopted pursuant to it, the manufacturer shall supply the information required in point 5 only if it is not already provided in the correspondent approval certificate and/or test report. However, the information referred to in the certificate of conformity (Annex III to this Regulation) shall be supplied in any case. 5.   INFORMATION DOCUMENT DATA ENTRIES A.    GENERAL INFORMATION 1.   GENERAL INFORMATION CONCERNING VEHICLES 1.1.    Make (trade name of manufacturer) ( 18 ) : … 1.2.    Type ( 17 ) : … 1.2.1   Variant(s) ( 17 ): … 1.2.2   Version(s) ( 17 ): … 1.2.3.   Commercial name(s) (if available): … 1.2.4.   Type-approval number(s) of the previous stage(s) ( 3 ) ( 18 ): … 1.3.    Category, subcategory and speed index of vehicle ( 2 ) : … 1.4.    Company name and address of manufacturer ( 18 ) : … 1.4.1.   Name(s) and address(es) of assembly plant(s): … 1.4.2.   Name and address of manufacturer's authorised representative (if any): … 1.5.    Manufacturer's statutory plate(s) 1.5.1.   Location of the manufacturer's statutory plate ( 18 ): … 1.5.2.   Method of attachment ( 18 ): … 1.5.3.   Photographs and/or drawings of the statutory plate (completed example with dimensions) ( 18 ): … … 1.6.    Vehicle identification number 1.6.1.   Location of the vehicle identification number on the chassis: … 1.6.2.   Photographs and/or drawings of the locations of the vehicle identification number (completed example with dimensions): … 1.6.1.1.   The vehicle identification number of the type begins with: … 2.   GENERAL INFORMATION CONCERNING SYSTEMS, COMPONENTS OR SEPARATE TECHNICAL UNITS 2.1.    Make(s) (trade name(s) of manufacturer): … 2.2.    Type ( 49 ) : … 2.2.1.   Commercial name(s) (if available): … 2.2.2.   Type-approval number(s) ( 49 ) (if available): … 2.2.3.   Type-approval(s) issued on (date, if available): … 2.2.4.   For components and separate technical units, location and method of attachment of the type-approval mark(s) (if available) ( 19 ): … 2.3.    Company name and address of manufacturer: … 2.3.1.   Name(s) and address(es) of assembly/manufacture plants: … 2.3.2.   Name and address of manufacturer's authorised representative (if any): … 2.4.    For systems and separate technical units, vehicle(s) for which they are intended for ( 21 ) : 2.4.1.   Type ( 17 ): … 2.4.2.   Variant(s) ( 17 ): … 2.4.3.   Version(s) ( 17 ): … 2.4.4.   Commercial name(s) (if available): … 2.4.5.   Category, subcategory and speed index of the vehicle ( 2 ): … 2.5.    Additional general information for engines 2.5.1.   Type-approval of: engine type/engine family ( 4 ): … 2.5.2.   Manufacturer's type coding (as marked on the engine or other means of identification): 2.5.3.   Commercial description of the parent- and (if applicable) of the family engine: … 2.5.4.    Additional marks for engines 2.5.4.1.   Location, coding and method of affixing the engine identification number: … 2.5.4.2.   Photographs and/or drawings of the location of the engine identification number (completed example with dimensions): … 3.   GENERAL CONSTRUCTION CHARACTERISTICS 3.1.   Photographs or drawings of a representative version of the vehicle: … 3.2.   Scale and dimensioned drawing of the whole vehicle: … 3.3.    For T- and C-category vehicles: 3.3.1.   Number of axles and wheels: … 3.3.2.   Number and position of axles with twinned wheels ( 23 ): … 3.3.3.   Number and position of steered axles ( 23 ): … 3.3.4.   Number and position of powered axles ( 23 ): … 3.3.5.   Number and position of braked axles ( 23 ): … 3.4.    For C-category vehicles 3.4.1.   Crawler undercarriage configuration: set of track trains at front/set of track trains at rear/set of track trains at front and set of track trains at rear/continuous track train at each side of the vehicle ( 4 ) 3.4.2.   Number and position of powered set of track trains ( 22 ): … 3.4.3.   Number and position of braked set of track trains ( 22 ): … 3.4.4.    Steering for C-category vehicles 3.4.4.1.   Steering by changing the speed between the left-hand side and right-hand side track trains: yes/no/not applicable ( 4 ) 3.4.4.2.   Steering by pivoting of two opposite or all four track trains: yes/no/not applicable ( 4 ) 3.4.4.3.   Steering by articulation of the front and rear part of the vehicle around a central vertical axis: yes/no/not applicable ( 4 ) 3.4.4.4.   Steering by articulation of the front and rear part of the vehicle around a central vertical axis and by changing the direction of the wheels on the wheeled axle: yes/no/not applicable ( 4 ) 3.4.5.   Mean Ground Contact Pressure, P: … MPa 3.5.    Chassis 3.5.1.   Chassis overall drawing: … 3.5.2.   For T- and C-category vehicles, type of chassis: backbone/central tube/ladder/articulated/chassis with side members/other ( 4 ) (if other: specify: …) 3.5.3.   For R- and S-category vehicles, type of chassis: drawbar/rigid drawbar/centre-axle/other ( 4 ) (if other: specify: …) 3.6.   Material used for the bodywork: … 3.7.   Position and arrangement of the engine: … 3.8.   Position of the steering wheel: left/right/centre ( 4 ): … 3.9.   Vehicle is equipped to be driven in right/left ( 4 ) -hand traffic and in countries that use metric/metric and imperial units in the speedometer ( 4 ); 3.10.   T- or C-category vehicles equipped for forestry applications: yes/no ( 4 ) 3.11.   T- or C-category vehicles equipped for protection against hazardous substances: yes/no ( 4 ) 3.12.   For R- and S-category vehicles, type of braking: unbraked/inertia-braked/continuous braked/semi-continuous braked/hydraulic braked/pneumatic braked ( 4 ) 4.   MASSES AND DIMENSIONS (in kg and mm) (Refer to drawings where applicable) 4.1    Range of vehicle mass (overall) 4.1.1.    Unladen mass 4.1.1.1.   Unladen mass(es) in running order ( 13 ): 4.1.1.1.1. Maximum: … kg ( 30 ) 4.1.1.1.2. Minimum: … kg ( 30 ) 4.1.1.1.3. Distribution of this (these) mass(es) among the axles: … kg 4.1.1.1.4. In the case of a rigid drawbar or centre- axle R- or S-category vehicle indicate the vertical load on the coupling point (S): … kg 4.1.2.    Maximum mass(es), as declared by the manufacturer 4.1.2.1.   Technically permissible maximum laden mass(es) of the vehicle ( 13 ): … kg 4.1.2.1.1   Technically permissible maximum mass(es) per axle: Axle 1 … kg Axle 2 … kg Axle …:… kg 4.1.2.1.2.   In the case of a rigid drawbar or centre-axle R- or S-category vehicle indicate the vertical load on the coupling point (S): … kg 4.1.2.1.3.   Limits on the distribution of this (these) mass(es) among the axles (specify the minimum limits in percentages on the front axle and on the rear axle): … % 4.1.2.2.   Mass(es) and tyre(s) Tyre combination No Axle No Tyre dimension including load capacity index and speed category symbol Rolling radius ( 1 ) [mm] Rim Size Off-set Tyre Load rating per tyre [kg] Maximum permissible mass per axle [kg]  ( *4 ) Maximum permissible mass of the vehicle [kg]  ( *4 ) Maximum permissible vertical load on the coupling point [kg]  ( *4 )  ( *5 ) Tyre pressure [kPa]  ( *6 ) On-road use Off-road use 1 1 …       … … … … … … 2 …       … … … … … … … …       … … … … … … 2 1 …       … … … … … …   2 …       … … … … … …   … …       … … … … … … … 1 …       … … … … … …   2 …       … … … … … …   … …       … … … … … … 4.1.2.3.   Mass(es) and crawler undercarriage Set of track trains No Track dimensions Average contact pressure on the ground [kPa] Maximum load per track roller [kg]  ( *7 ) Maximum permissible mass per set of track trains [kg]  ( *7 ) Maximum permissible mass of the vehicle [kg]  ( *7 ) Maximum permissible vertical load on the coupling point [kg]  ( *7 )  ( *8 ) Length [mm] Width [mm] 1 …   … … … … … 2 …   … … … … … … …   … … … … … 4.1.2.4.   Payload(s) ( 13 ): … kg 4.1.3.   Technically permissible towable mass(es) for T- or C-category vehicles for each chassis/braking configuration of the R- or S-category vehicle (for R- and S-category vehicles, indicate the maximum permissible load(s) on the rear coupling point): R- and S category vehicle Brake Drawbar Rigid drawbar Centre-axle Unbraked … kg … kg … kg Inertia-braked … kg … kg … kg Continuous or semi-continuous braked … kg … kg … kg hydraulic or pneumatic braked … kg … kg … kg 4.1.4.   Total technically permissible mass(es) of the tractor (T- or C-category vehicle) and towed vehicle (R- or S-category vehicle) combination for each chassis/braking configuration of the R- or S-category vehicle: R- and S category vehicle Brake Drawbar Rigid drawbar Centre-axle Unbraked … kg … kg … kg Inertia-braked … kg … kg … kg Continuous or semi-continuous braked … kg … kg … kg hydraulic or pneumatic braked … kg … kg … kg 4.1.5.   Maximum permissible vertical load on the coupling point (irrespective of the tyres and the rear coupling device(s)): 4.1.5.1.   of the T and C category vehicle: … kg 4.1.5.2.   of the R- and S-category vehicle: … kg 4.1.5.3.   Maximum mass of the combination at maximum unbraked mass: … kg 4.2.    Range of vehicle dimensions (overall) 4.2.1.    For incomplete vehicles 4.2.1.1.   Length ( 31 ) 4.2.1.1.1.   Maximum permissible length for the completed vehicle: … mm 4.2.1.1.2.   Minimum permissible length for the completed vehicle: … mm 4.2.1.2.   Width ( 32 ) 4.2.1.2.1.   Maximum permissible width for the completed vehicle: … mm 4.2.1.2.2.   Minimum permissible width for the completed vehicle: … mm 4.2.1.3.   Height (in running order) ( 33 ): … mm 4.2.1.4.   Forward overhang ( 34 ): … mm 4.2.1.4.1.   For T- and C-category vehicles: approach angle: … degrees 4.2.1.5.   For T- and C-category vehicles: rear overhang ( 35 ): … mm 4.2.1.5.1.   For T- and C-category vehicles: departure angle: … degrees 4.2.1.5.2.   Minimum and maximum permissible overhang of the coupling point ( 35 ) ( 46 ): … mm 4.2.1.6.   For T- and C-category vehicles: ground clearance ( 36 ) 4.2.1.6.1.   Between the axles: … mm 4.2.1.6.2.   Under the front axle(s): … mm 4.2.1.6.3.   Under the rear axle(s): … mm 4.2.1.7.   Extreme permissible positions of the centre of gravity for the completed vehicle: … mm 4.2.1.7.1.   For T- and C- category vehicles, extreme permissible positions of the centre of gravity of the body and/or interior fittings and/or equipment and/or payload: … mm 4.2.2.    For complete/completed ( 4 ) vehicles 4.2.2.1.   Overall dimensions of the vehicle, including mechanical coupling: 4.2.2.1.1.   Length for on-road use ( 31 ) 4.2.2.1.1.1.   Maximum: … mm 4.2.2.1.1.2.   Minimum: … mm 4.2.2.1.2.   Width for on-road use ( 32 ) 4.2.2.1.2.1.   Maximum: … mm 4.2.2.1.2.2.   Minimum: … mm 4.2.2.1.3.   Height for on-road use ( 33 ) ( 47 ) 4.2.2.1.3.1.   Maximum: … mm 4.2.2.1.3.2.   Minimum: … mm 4.2.2.2.   Forward overhang ( 34 ) ( 48 ) 4.2.2.2.1.   Maximum: … mm 4.2.2.2.2.   Minimum: … mm 4.2.2.3.   Rear overhang ( 35 ) 4.2.2.3.1.   Maximum: … mm 4.2.2.3.2.   Minimum: … mm 4.2.2.4.   Ground clearance ( 36 ) 4.2.2.4.1.   Maximum: … mm 4.2.2.4.2.   Minimum: … mm 4.2.2.5.   Wheelbase ( 37 ): … mm 4.2.2.6.   Distance(s) between consecutive axles 1-2: … mm 2-3: … mm, 3-4: … mm, etc. 4.2.2.7.   For rigid draw bar and centre axle R- and S-category vehicles: 4.2.2.7.1. Distance between the coupling point and the first axle: … mm 4.2.2.7.2. Distance between the coupling point and the last axle: … mm 4.2.2.8.   Maximum and minimum width of track of each axle (measured between the symmetry planes of the single or twin tyres or of the tyres in triple formation normally fitted) (to be stated by the manufacturer) ( 38 ): 4.2.2.8.1. Maximum: Axle 1 … mm Axle 2 … mm Axle …:… mm 4.2.2.8.2. Minimum: Axle 1 … mm Axle 2 … mm Axle …:… mm 4.2.2.9.   Position of centre of gravity of the vehicle in the longitudinal, transverse and vertical direction: … 4.2.2.9.1.   For T2-, T4.1-, T4.3-category vehicles and C2-, C4.1-, C4.3-category vehicles, height of the centre of gravity, measured in relation to the ground using the tyres normally fitted on the vehicle: … mm 4.2.2.9.1.1.   For T2-and C2-category vehicles, indicate the ratio between entry 4.2.2.9.1 and the average minimum track for each axle: Axle 1 … Axle 2 … Axle …:… 4.2.2.9.1.2.   For T4.1-and C4.1-category vehicles, indicate the ratio between entry 4.2.2.9.1 and the average minimum track of all of the axles: … 5.   GENERAL POWERTRAIN CHARACTERISTICS 5.1.    Maximum vehicle speed 5.1.1.    Forward maximum vehicle speed 5.1.1.1.   Declared maximum design vehicle speed: … km/h 5.1.1.2.   Calculated maximum design vehicle speed in top gear (show factors used in calculation) ( 41 ): … km/h 5.1.1.3.   Measured maximum vehicle speed: … km/h ( 41 ) 5.1.2.    Rearward maximum vehicle speed ( 54 ) 5.1.2.1.   Declared rearward maximum design vehicle speed: … km/h 5.1.2.2.   Measured rearward maximum vehicle speed ( 41 ): … km/h 5.2.   Rated engine net power: … kW, at … min – 1 (in accordance with UNECE Regulation No 120 ( OJ L 257, 30.9.2010, p. 280 )) 5.3.   Maximum engine net power: … kW, at … min – 1 (in accordance with UNECE Regulation No 120 ( OJ L 257, 30.9.2010, p. 280 )) 5.4.   Maximum engine torque: … Nm, at … min – 1 (in accordance with UNECE Regulation No 120 ( OJ L 257, 30.9.2010, p. 280 )) 5.5.   Fuel type ( 9 ): … 5.6.   Actual forward movement of powered wheels corresponding to one complete revolution of the wheel: … B.    INFORMATION ON ENVIRONMENTAL AND PROPULSION PERFORMANCE 6.   ESSENTIAL CHARACTERISTICS OF THE PARENT ENGINE/ENGINE ( 4 ) 6.1.   Cycle: four stroke/two stroke ( 4 ) 6.2.   Bore ( 12 ) … mm 6.3.   Stroke ( 12 ): … mm 6.4.   Number … and layout ( 26 ) … of cylinders 6.5.   Engine capacity: … cm 3 6.6.   Rated speed: … 6.7.   Maximum torque speed: … 6.8.   Volumetric compression ratio ( 7 ): … 6.9.   Combustion system description: … 6.10.   Drawing(s) of combustion chamber and piston crown: … 6.11.   Minimum cross sectional area of inlet and outlet ports: … 6.12.    Cooling system 6.12.1.    Liquid 6.12.1.1.   Nature of liquid: … 6.12.1.2.   Circulating pumps: yes/no ( 4 ) 6.12.1.2.1.   Characteristics or make(s) and type(s) (if applicable) of the circulating pumps: … 6.12.1.2.2.   Drive ratio(s) (if applicable): … 6.12.2.    Air 6.12.2.1.   Blower: yes/no ( 4 ) 6.12.2.1.1.   Characteristics of the blower. … 6.12.2.1.2.   Drive ratio(s) (if applicable): … 6.13.    Temperature permitted by the manufacturer 6.13.1.   Liquid cooling: maximum temperature at outlet: … K 6.13.2.   Air cooling: reference point … 6.13.2.1.   Maximum temperature at reference point: … K 6.13.3.   Maximum charge air outlet temperature of the intercooler outlet (if applicable): … K 6.13.4.   Maximum exhaust temperature at the point in the exhaust pipe(s) adjacent to the outer flange(s) of the exhaust manifold(s): … K 6.13.5.   Lubricant temperature: minimum: … K, maximum: … K 6.14.    Pressure charger 6.14.1.   Pressure charger: yes/no ( 4 ) 6.14.2.   Make: … 6.14.3.   Type: … 6.14.4.   Description of the system (e.g. maximum charge pressure, waste gate, if applicable): … 6.14.5.   Intercooler: yes/no ( 4 ) 6.15.   Intake system: maximum allowable intake depression at rated engine speed and at 100 % load: … kPa 6.16.   Exhaust system: maximum permissible exhaust backpressure at rated engine speed and at 100 % load: … kPa 6.17.    Measures taken against air pollution 6.17.1.   Device for recycling crankcase gases: yes/no ( 4 ) 6.17.2.   Additional anti-pollution devices (if any): 6.17.2.1.   Catalytic converter: yes/no ( 4 ) 6.17.2.1.1.   Make: … 6.17.2.1.2.   Type … 6.17.2.1.3.   Number of catalytic converters and elements … 6.17.2.1.4.   Dimensions and volume of the catalytic converter(s): … 6.17.2.1.5.   Type of catalytic action … 6.17.2.1.6.   Total charge of precious metals: … 6.17.2.1.7.   Relative concentration: … 6.17.2.1.8.   Substrate (structure and material): … 6.17.2.1.9.   Cell density: … 6.17.2.1.10.   Type of casing for the catalytic converter(s): … 6.17.2.1.11.   Location of the catalytic converter(s) (place(s) and maximum/minimum distance(s) from engine: … 6.17.2.1.12.   Normal operating range: … K 6.17.2.1.13.   Consumable reagent (where appropriate) … 6.17.2.1.13.1.   Type and concentration of reagent needed for catalytic action: … 6.17.2.1.13.2.   Normal operational temperature range of reagent: … 6.17.2.1.13.3.   International standard (if applicable): … 6.17.2.1.14.   NO x sensor: yes/no ( 4 ) 6.17.2.1.15.   Oxygen sensor: yes/no ( 4 ) 6.17.2.1.15.1.   Make: … 6.17.2.1.15.2.   Type … 6.17.2.1.15.3.   Location: … 6.17.2.1.16.   Air injection: yes/no ( 4 ) 6.17.2.1.16.1.   Type: pulse air/air pump/other ( 4 ) (if other: specify: …) 6.17.2.1.17.   EGR: yes/no ( 4 ) 6.17.2.1.17.1.   Characteristics (cooled/uncooled, high pressure/low pressure, etc.): … 6.17.2.1.18.   Particulate trap: yes/no ( 4 ) 6.17.2.1.18.1.   Dimensions and capacity of the particulate trap: … 6.17.2.1.18.2.   Type and design of the particulate trap: … 6.17.2.1.18.3.   Location (place(s) and maximum/minimum distance(s) from engine: … 6.17.2.1.18.4.   Method or system of regeneration, description and/or drawing: … 6.17.2.1.18.5.   Normal operating temperature range: … K and pressure range: … kPa 6.17.2.1.19.   Other systems: yes/no ( 4 ) 6.17.2.1.19.1.   Description and operation: … 6.18.    Fuel feed for diesel engines 6.18.1.    Feed pump 6.18.1.1   Pressure ( 7 ) … kPa or characteristic diagram: … 6.18.2.    Injection system 6.18.2.1.   Pump 6.18.2.1.1.   Make(s): … 6.18.2.1.2.   Type(s): … 6.18.2.1.3.   Delivery: … and … mm 3 ( 7 ) per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: … 6.18.2.1.3.1.   Method used: on engine/on pump bench ( 4 ) 6.18.2.2.   Injection advance: 6.18.2.2.1.   Injection advance curve ( 7 ): … 6.18.2.2.2.   Timing ( 7 ): … 6.18.2.3.   Injection piping: 6.18.2.3.1.   Length: … mm 6.18.2.3.2.   Internal diameter: … mm 6.18.2.4.   Injector(s) 6.18.2.4.1.   Make(s) … 6.18.2.4.2.   Type(s): … 6.18.2.4.3.   Opening pressure ( 7 ): … kPa, or characteristic diagram: … 6.18.2.4.   Governor 6.18.2.4.1.   Make(s) … 6.18.2.4.2.   Type(s): … 6.18.2.4.3.   Speed at which cut-off starts under full load ( 7 ): … 6.18.2.4.4.   Maximum no-load speed ( 7 ): … 6.18.2.4.5.   Idling speed ( 7 ): … 6.18.2.5.   Cold-start system 6.18.2.5.1.   Make(s): … 6.18.2.5.2.   Type(s): … 6.18.2.5.3.   Description: … 6.19.    Fuel for petrol engines 6.19.1.   Carburettor: … 6.19.1.1.   Make(s): … 6.19.1.2.   Type(s): … 6.19.2.   Port fuel injection: single-point/multi-point ( 4 ) 6.19.2.1   Make(s): … 6.19.2.2.   Type(s): … 6.19.3.   Direct injection: … 6.19.3.1   Make(s): … 6.19.4.2.   Type(s): … 6.20.    Valve timing 6.20.1.   Maximum lift and angles of opening and closing in relation to dead centre or equivalent data: … 6.20.2.   Reference and/or setting range ( 4 ): … 6.20.3.    Variable valve timing system (if applicable and where intake and/or exhaust) 6.20.3.1.   Type: continuous type/on/off type ( 4 ) 6.20.3.2   Cam phase shift angle: … 6.21.    Porting configuration 6.21.1.   Position, size and numbering: … 6.22.    Ignition system 6.22.1.    Ignition coil 6.22.1.1.   Make(s): … 6.22.1.2.   Type(s): … 6.22.1.3.   Number: … 6.22.2.   Spark plug(s): … 6.22.2.1.   Make(s): … 6.22.2.2.   Type(s): … 6.22.3.   Magneto: … 6.22.3.1.   Make(s): … 6.22.3.2.   Type(s): … 6.22.4.   Ignition timing: … 6.22.4.1.   Static advance with respect to top dead centre (crank angle degrees): … 6.22.4.2.   Advance curve (if applicable): … 7.   ESSENTIAL CHARACTERISTICS OF THE ENGINE FAMILY 7.1.    Common parameters ( 56 ) 7.1.1   Combustion cycle: … 7.1.2   Cooling medium … 7.1.3   Method of air aspiration: … 7.1.4   Combustion chamber type and design: … 7.1.5   Valve and porting configuration, size and number: … 7.1.6   Fuel system: … 7.1.7    Engine management systems (proof of identity pursuant to drawing number(s)) 7.1.7.1.   Charge cooling system … 7.1.7.2.   Exhaust gas recirculation ( 3 ): … 7.1.7.3.   Water injection/emulsion ( 4 ) ( 3 ): … 7.1.7.4.   Air injection ( 3 ): … 7.1.8   Exhaust after-treatment system ( 3 ): … 7.2.    Engine family listing 7.2.1.   Name of engine family: … 7.2.2.   Specifications of engines within the family:   Parent engine Engines within the family Engine type           Number of cylinders           Rated speed (min – 1 )           Fuel delivery per stroke (mm 3 ) for diesel engines, fuel flow (g/h) for petrol engines, at rated net power           Rated net power (kW)           Maximum power speed (min – 1 )           Maximum net power (kW)           Maximum torque speed (min – 1 )           Fuel delivery per stroke (mm 3 ) for diesel engines, fuel flow (g/h) for petrol engines, at maximum torque           Maximum torque (Nm)           Low Idle speed (min – 1 )           Cylinder displacement (in % of parent engine) 100         8.   ESSENTIAL CHARACTERISTICS OF THE ENGINE TYPE WITHIN THE FAMILY 8.1.   Cycle: four stroke/two stroke ( 4 ): … 8.2.   Bore ( 12 ): … mm 8.3.   Stroke ( 12 ): … mm 8.4.   Number … and layout ( 26 ) … of cylinders 8.5.   Engine capacity: … cm 3 8.6.   Rated speed … 8.7.   Maximum torque speed … 8.8.   Volumetric compression ratio ( 7 ): … 8.9.   Combustion system description: … 8.10.   Drawings of combustion chamber and piston crown: … 8.11.   Minimum cross sectional area of inlet and outlet ports: … 8.12.    Cooling system 8.12.1.    Liquid 8.12.1.1.   Nature of liquid: … 8.12.1.2.   Circulating pumps: yes/no ( 4 ) 8.12.1.2.1.   Characteristics or make(s) and type(s) (if applicable) of the circulating pumps: … 8.12.1.2.2.   Drive ratio(s) (if applicable): … 8.12.2.    Air 8.12.2.1.   Blower: yes/no ( 4 ) 8.12.2.1.1.1   Characteristics of the blower. … 8.12.1.2.1.2.   Drive ratio(s) (if applicable): … 8.13.    Temperature permitted by the manufacturer 8.13.1.   Liquid cooling: maximum temperature at outlet: … K 8.13.2.   Air cooling: reference point … 8.13.2.1.   Maximum temperature at reference point: … K 8.13.3.   Maximum charge air outlet temperature of the intercooler outlet (if applicable): … K 8.13.4.   Maximum exhaust temperature at the point in the exhaust pipe(s) adjacent to the outer flange(s) of the exhaust manifold(s): … K 8.13.5.   Lubricant temperature: minimum: … K, maximum: … K 8.14.    Pressure charger 8.14.1.   Pressure charger: yes/no ( 4 ) 8.14.2.   Make: … 8.14.3.   Type: … 8.14.4.   Description of the system (e.g. maximum charge pressure, waste gate, if applicable): … 8.14.5.   Intercooler: yes/no ( 4 ) 8.15.   Intake system: maximum allowable intake depression at rated engine speed and at 100 % load: … kPa 8.16.   Exhaust system: maximum permissible exhaust backpressure at rated engine speed and at 100 % load: … kPa 8.17.    Measures taken against air pollution 8.17.1.   Device for recycling crankcase gases: yes/no ( 4 ) 8.17.2.   Additional anti-pollution devices (if any): 8.17.2.1.   Catalytic converter: yes/no ( 4 ) 8.17.2.1.1.   Make: … 8.17.2.1.2.   Type … 8.17.2.1.3.   Number of catalytic converters and elements … 8.17.2.1.4.   Dimensions and volume of the catalytic converter(s): … 8.17.2.1.5.   Type of catalytic action … 8.17.2.1.6.   Total charge of precious metals: … 8.17.2.1.7.   Relative concentration: … 8.17.2.1.8.   Substrate (structure and material): … 8.17.2.1.9.   Cell density: … 8.17.2.1.10.   Type of casing for the catalytic converter(s): … 8.17.2.1.11.   Location of the catalytic converter(s) (place(s) and maximum/minimum distance(s) from engine: … 8.17.2.1.12.   Normal operating range: … K 8.17.2.1.13.   Consumable reagent (where appropriate) … 8.17.2.1.13.1.   Type and concentration of reagent needed for catalytic action: … 8.17.2.1.13.2.   Normal operational temperature range of reagent: … 8.17.2.1.13.3.   International standard (if applicable): … 8.17.2.1.14.   NO x sensor: yes/no ( 4 ) 8.17.2.1.15.   Oxygen sensor: yes/no ( 4 ) 8.17.2.1.15.1.   Make: … 8.17.2.1.15.2.   Type … 8.17.2.1.15.3.   Location: … 8.17.2.1.16.   Air injection: yes/no ( 4 ) 8.17.2.1.16.1.   Type: pulse air/air pump/other ( 4 ) (if other specify: …) 8.17.2.1.16.   EGR: yes/no ( 4 ) 8.17.2.1.16.1.   Characteristics (cooled/uncooled, high pressure/low pressure, etc.): … 8.17.2.1.17.   Particulate trap: yes/no ( 4 ) 8.17.2.1.17.1.   Dimensions and capacity of the particulate trap: … 8.17.2.1.17.2.   Type and design of the particulate trap: … 8.17.2.1.17.3.   Location (place(s) and maximum/minimum distance(s) from engine: … 8.17.2.1.17.4.   Method or system of regeneration, description and/or drawing: … 8.17.2.1.17.5.   Normal operating temperature range: … K and pressure range: … kPa 8.17.2.1.18.   Other systems: yes/no ( 4 ) 8.17.2.1.18.1.   Description and operation: … 8.18.    Fuel feed for diesel engines 8.18.1.    Feed pump 8.18.1.1   Pressure ( 7 ) … kPa or characteristic diagram: … 8.18.2.    Injection system 8.18.2.1.   Pump 8.18.2.1.1.   Make(s): … 8.18.2.1.2.   Type(s): … 8.18.2.1.3.   Delivery: … and … mm 3 ( 7 ) per stroke or cycle at full injection at pump speed of: … rpm (rated) and: … rpm (maximum torque) respectively, or characteristic diagram: … 8.18.2.1.3.1.   Method used: on engine/on pump bench ( 4 ) 8.18.2.2.   Injection advance: 8.18.2.2.1. Injection advance curve ( 7 ): … 8.18.2.2.2. Timing ( 7 ): … 8.18.2.3.   Injection piping: 8.18.2.3.1. Length: … mm 8.18.2.3.2. Internal diameter: … mm 8.18.2.4.   Injector(s) 8.18.2.4.1.   Make(s) … 8.18.2.4.2.   Type(s): … 8.18.2.4.3.   Opening pressure ( 7 ): … kPa, or characteristic diagram: … 8.18.2.4.   Governor 8.18.2.4.1.   Make(s) … 8.18.2.4.2.   Type(s): … 8.18.2.4.3.   Speed at which cut-off starts under full load ( 7 ): … 8.18.2.4.4.   Maximum no-load speed ( 7 ): … 8.18.2.4.5.   Idling speed ( 7 ): … 8.18.2.5.   Cold-start system 8.18.2.5.1.   Make(s): … 8.18.2.5.2.   Type(s): … 8.18.2.5.3.   Description: … 8.19.    Fuel for petrol engines 8.19.1.   Carburettor: … 8.19.1.1.   Make(s): … 8.19.1.2.   Type(s): … 8.19.2.   Port fuel injection: single-point/multi-point ( 4 ) 8.19.2.1   Make(s): … 8.19.2.2.   Type(s): … 8.19.3.   Direct injection: … 8.19.3.1   Make(s): … 8.19.4.2.   Type(s): … 8.20.    Valve timing 8.20.1.   Maximum lift and angles of opening and closing in relation to dead centre or equivalent data: … 8.20.2.   Reference and/or setting range ( 4 ): … 8.20.3.    Variable valve timing system (if applicable and where intake and/or exhaust) 8.20.3.1.   Type: continuous type/on/off type ( 4 ) 8.20.3.2   Cam phase shift angle: … 8.21.    Porting configuration 8.21.1.   Position, size and numbering: … 8.22.    Ignition system 8.22.1.    Ignition coil 8.22.1.1.   Make(s): … 8.22.1.2.   Type(s): … 8.22.1.3.   Number: … 8.22.2.   Spark plug(s): … 8.22.2.1.   Make(s): … 8.22.2.2.   Type(s): … 8.22.3.   Magneto: … 8.22.3.1.   Make(s): … 8.22.3.2.   Type(s): … 8.22.4.   Ignition timing: … 8.22.4.1.   Static advance with respect to top dead centre (crank angle degrees): … 8.22.4.2.   Advance curve (if applicable): … 9.   ENERGY STORAGE DEVICE(S) 9.1.   Description: battery/capacitor/flywheel/generator ( 4 ) 9.2.   Identification number: … 9.3.   Kind of electrochemical couple: … 9.4.   Energy stored 9.4.1.   For battery, voltage … and capacity: … Ah in 2h 9.4.2.   For capacitor: J,… , 9.4.3.   For flywheel/generator ( 4 ): J, … 9.4.3.1.   Flywheel moment of inertia: … 9.4.3.1.1.   Additional moment of inertia if no gear is engaged: … 9.5.   Charger: on-board/external/without ( 4 ) 10.   EXTERNAL SOUND LEVEL 10.1.    External sound level declared by the manufacturer 10.1.1.   Moving: … dB(A) 10.1.2   Stationary: … dB(A) 10.1.3.   At engine speed: … min – 1 10.2.   Brief description and schematic drawing of exhaust system (including the air intake system, the devices for noise and tailpipe emission control): … 10.3.    Air-intake system 10.3.1.   Intake manifold description (include drawings and/or photos) ( 10 ): … 10.3.2.    Air filter 10.3.2.1.   Photographs and/or drawings: … 10.3.2.2.   Make: … 10.3.2.3.   Type: … 10.3.3.    Intake silencer 10.3.3.1.   Photographs and/or drawings: … 10.3.3.2.   Make: … 10.3.3.3.   Type: … 10.4.    Exhaust system 10.4.1.   Description and/or drawing of the exhaust manifold ( 10 ): … 10.4.2.   Description and/or drawing of the elements of the exhaust system that are not part of the engine system: … 10.4.3.   Maximum allowable exhaust back pressure at rated engine speed and at 100 % load: … kPa 10.4.4.   Type, marking of the exhaust noise-abatement device(s): … 10.4.4.1.   Exhaust noise-abatement device containing fibrous materials: yes/no ( 4 ): … 10.4.5.   Exhaust system volume: … dm 3 10.4.6.   Location of the exhaust outlet: … 10.4.7.   Additional noise-reducing measures in the engine compartment and on the engine for external noise (if any): … 10.5.   Details of any non-engine related devices designed to reduce noise (if not covered by other items): … 11.   DRIVE-TRAIN AND CONTROL ( 13 ) 11.1.   Brief description and schematic drawing of the vehicle drive-train and its control system (gear shift control, clutch control or any other element of drive-train): … 11.2.    Transmission 11.2.1.   Brief description and schematic drawing of gear shift system(s) and its control: … 11.2.2.   Diagram and or drawing of the transmission system: … 11.2.3.   Type of transmission: mechanical/hydraulic/electric/other ( 4 ) (if other specify …) 11.2.3.1   Brief description of the electrical/electronic components (if any): … 11.3.    Clutch (if any) 11.3.1.   Brief description and schematic drawing of the clutch and its control system: … 11.3.2.   Clutch type: … 11.3.3.   Maximum torque conversion: … 11.4.    Gearbox (if any) 11.4.1.   Type ( 24 ): … 11.4.2.   Location relative to the engine: … 11.4.3.   Method of control: … 11.4.4.   Transfer box: with/without ( 4 ) 11.5.    Gear ratios Gear Internal gearbox ratios (ratios of engine to gearbox output shaft revolutions) Internal transfer box ratios (ratios of engine to transfer box output shaft revolutions) Final drive ratio(s) (ratio of gearbox output shaft to driven wheel revolutions) Total gear ratios Ratio (engine speed/vehicle speed) for manual transmission only Maximum for CVT  ( *9 ) 1 2 3           Minimum for CVT  ( *9 ) Reverse 1 …           11.6.    Differential lock 11.6.1.   Differential lock: yes/no/optional ( 4 ) C.    INFORMATION ON FUNCTIONAL SAFETY 12.   PROPULSION AND/OR DRIVE-TRAIN OUTPUT GOVERNORS 12.1.   Number of speed governors: … 12.2.   Nominal cut-off point No 1: … 12.2.1.   Engine/motor/drive-train rotation speed at which cut-off starts under load: … min – 1 12.2.2.   Maximum rotation speed at the minimum engine load: … min – 1 12.3.   Nominal cut-off point No 2: … 12.3.1   Engine/motor/drive-train rotation speed at which cut-off starts under load ( 4 ): … min – 1 12.3.2.   Maximum rotation speed at the minimum engine load: … min – 1 12.4.   The stated purpose of governor(s): maximum design vehicle speed limitation/maximum power limitation/engine over-speed protection ( 4 ): … 12.5.   Adjustable speed limitation device complying with the requirements for N2- and N3-category vehicles set out in points 1 and 2, Part II point 13.2, Part III points 21.2 and 21.3, Annex 5 point 1 and Annex 6 to UNECE Regulation No 89 ( OJ L 158, 19.6.2007, p. 1 ). with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 13.   STEERING 13.1.   Schematic diagram of steered axle(s) showing steering geometry: … 13.2.   Steering category: manual/power-assisted/servo steering/differential ( 4 ) 13.3.    Transmission and control of steering 13.3.1.   Configuration of steering transmission (specify for front and rear, if applicable): … 13.3.2.   Linkage to the wheels (including other than mechanical means; specify for front and rear, if applicable): … 13.3.2.1.   Brief description of the electrical/electronic components (if any): … 13.3.3.   Method of assistance (if any): … 13.3.3.1.   Method and diagram of operation, make(s) and type(s): … 13.3.4.   Diagram of the steering equipment as a whole, showing the position on the vehicle of the various devices influencing its steering behaviour: … 13.3.5.   Schematic diagram(s) of the steering control(s): … 13.3.6.   Range and method of adjustment of the steering control(s): … 13.3.7.   Brief description of the electrical/electronic components (if any): … 13.4.    Maximum turning angle of the wheels (if fitted) 13.4.1.   To the right: … degrees Number of steering wheel turns: … 13.4.2.   To the left: … degrees Number of steering wheel turns: … 13.5.    Minimum turning circle (without braking) ( 42 ) 13.5.1   To the right: … mm 13.5.2   To the left: … mm 13.5.3.   Method of power assistance (if any): … 13.5.3.1.   Method and diagram of operation, make(s) and type(s): … 13.6.    Steering for fast (‘b’ speed index) T-category vehicles 13.6.1.   Requirements under sections 2, 5 and 6 and in Annexes 4 and 6 to UNECE Regulation No 79 ( OJ L 137, 27.5.2008, p. 25 ) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 13.6.2.   Requirements on steering effort as set out in section 6 of UNECE Regulation No 79 ( OJ L 137, 27.5.2008, p. 25 ) for N2-category vehicles are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 13.6.3.   Requirements under ISO 10998:2008, Amd 1 2014 (Agricultural tractors — Requirements for steering) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 13.7.    Complex electronic control systems that affect the steering function 13.7.1.   Requirements under Annex 6 to UNECE Regulation No 79 ( OJ L 137, 27.5.2008, p. 25 ) are met by the complex electronic vehicle control systems that affect the steering function, with relevant documentation included in the information document: yes/no ( 4 ) 14.   SPEEDOMETER, ODOMETER, TACHOMETER AND HOUR METER 14.1.    Speedometer 14.1.1.   Photographs and/or drawings of the complete system: … 14.1.2.   Vehicle speed range displayed: … 14.1.3.   Tolerance of the measuring mechanism of the speedometer: … 14.1.4.   Technical constant of the speedometer: … 14.1.5.   Method of operation and description of the drive mechanism: … 14.1.6.   Overall transmission ratio of the drive mechanism: … 14.1.7.   Design of the instrument dial or of the other forms of read-out: … 14.1.8.   Brief description of the electrical/electronic components: … 14.2.    Odometer 14.2.1.   Tolerance of the measuring mechanism of the odometer: … 14.2.2.   Method of operation and description of the drive mechanism: … 14.3.    Tachometer 14.3.1.   Tolerance of the measuring mechanism of the tachometer: … 14.3.2.   Method of operation and description of the drive mechanism: … 14.4.    Hour meter 14.4.1.   Tolerance of the measuring mechanism of the hour meter: … 14.4.2.   Method of operation and description of the drive mechanism: … 15.   FIELD OF VISION 15.1.   Drawing(s) and/or photograph(s) showing the location of component parts within the 180 o forward field of vision: … 15.2.   Requirements under ISO 5721-1:2013 (Agricultural tractors — Requirements, test procedures and acceptance criteria for the operator's field of vision — Part 1: Field of vision to the front) are met with relevant documentation included in the information document: yes/no ( 4 ) 15.3.   Requirements under ISO 5721-2:2014 (Agricultural tractors — Requirements, test procedures and acceptance criteria for the operator's field of vision — Part 2: Field of vision to the side and to the rear) are met with relevant documentation included in the information document: yes/no ( 4 ) 16.   WINDSCREEN WIPERS AND WASHERS AND DEFROSTING AND DEMISTING 16.1.    Windscreen wipers 16.1.1.   Requirements under ISO 5721-1:2013 (Agricultural tractors — Requirements, test procedures and acceptance criteria for the operator's field of vision — Part 1: Field of vision to the front) are met with relevant documentation included in the information document: yes/no ( 4 ) 16.1.2.   Alternatively to entry 16.1.1, provide a detailed technical description (including photographs or drawings) and the number and frequency of its operation: … 16.2.    Windscreen washer 16.2.1.   Detailed technical description (including photographs or drawings): … 16.2.2.   Capacity of the reservoir: … l 16.3.    Defrosting and demisting 16.3.1.   Detailed technical description (including photographs or drawings): … 16.3.2.   Maximum electrical consumption: … kW 17.   GLAZING 17.1.   The following requirements under UNECE Regulation 43 ( OJ L 42, 12.2.2014, p. 1 ) are met with the relevant documentation included in the information document: … 17.2.    Alternatively to entry 17.1, provide the following information: 17.2.1.   Data for quick identification of Driver's eyes reference point ( 59 ): … 17.2.2.   in the case of glazing other than windscreens, drawings in a format not exceeding A4 or folded to that format, showing: — the maximum area, — the smallest angle between two adjacent sides of the glass pane, and — the maximum height of segment, if any; 17.2.3.    Windscreen(s) 17.2.3.1.   Material(s) used: … 17.2.3.2.   Method of fitting: … 17.2.3.3.   Rake angle(s): … degrees 17.2.3.4.   Windscreen accessories and the position in which they are fitted, together with a brief description of any electrical/electronic components: … 17.2.3.5.   Drawing on a scale 1:10 and diagrams of the windscreens and their installation in the tractor in sufficient detail to show: 17.2.3.5.1. the position of the windscreen relative to the Driver's eyes reference point ( 59 ); 17.2.3.5.2. the rake angle of the windscreen; 17.2.3.5.3. the position and size of the zone in which the optical qualities are verified and, where appropriate, the area subjected to differential toughening; 17.2.3.5.4. the developed area of the windscreen; 17.2.3.5.5. the maximum height of segment of the windscreen; and 17.2.3.5.6. the curvature of the windscreen (for windscreen-grouping purposes only); 17.2.3.6.   in the case of double glazing, drawings in a format not exceeding A4 or folded to that format, showing, in addition to the information referred to in entry 17.2.2: — the type of each constituent glass pane, — the type of bonding (organic, glass-glass or glass-metal), — the nominal thickness of the gap between the two glass panes. 17.2.4.    Window(s) 17.2.4.1.   Position(s): … 17.2.4.2.   Material(s) used: … 17.2.4.3.   Brief description of the electrical/electronic components (if any) of the window operating mechanism: … 17.2.5.    Opening roof glazing 17.2.5.1.   Position(s): … 17.2.5.2.   Materials used: … 17.2.5.3.   Brief description of the electrical/electronic components (if any) of the roof glazing operating mechanism: … 17.2.6.    Other glass panes 17.2.6.1.   Position(s): … 17.2.6.2.   Materials used: … 17.2.6.3.   Brief description of the electrical/electronic components (if any) of the other glass panes operating mechanism: … 18.   REAR-VIEW MIRRORS 18.1.   Number and class(es) of the mirrors: … 18.2.   Requirements under UNECE Regulation No 46 ( OJ L 177, 10.7.2010, p. 211 ) are met with the relevant documentation included in the information document: yes/no/not applicable ( 4 ) 1.8.3.   Requirements under UNECE Regulation No 81 ( OJ L 185, 13.7.2012, p. 1 ) are met with the relevant documentation included in the information document: yes/no/not applicable ( 4 ) 18.4.   Drawing(s) for the identification of the mirror showing the position of the mirror relative to the vehicle structure: … 18.5.   Details of the method of attachment including that part of the vehicle structure to which it is attached: … 18.6.   Brief description of the electrical/electronic components of the adjustment system: … 18.7   Technical description of the defrosting and demisting system of the mirrors: … 18.8.   Optional equipment that might restrict the field of vision to the rear: … 18.9.    Field of vision for rear view mirror(s) of class II 18.9.1.   Complies with point 5.1 of Annex IX to Commission Delegated Regulation (EU) 2015/208: yes/no ( 4 ). 18.9.2.   Alternatively to entry 18.9.1, requirements under ISO 5721-2:2014 (Agricultural tractors — Requirements, test procedures and acceptance criteria for the operator's field of vision — Part 2: Field of vision to the side and to the rear) are met with relevant documentation included in the information document: yes/no ( 4 ). 19.   DEVICES FOR INDIRECT VISION OTHER THAN MIRRORS (OPTIONAL) 19.1.   Type and characteristics (such as a complete description of the device): … 19.2.   In the case of a camera-monitor device, the detection distance (mm), contrast, luminance range, glare correction, display performance (black and white/colour ( 4 )), image repetition frequency, luminance reach of the monitor ( 4 ): … 19.3.   Sufficiently detailed drawings to identify the complete device, including installation instructions: … 19.4.   Requirements under ISO 5721-2:2014 (Agricultural tractors — Requirements, test procedures and acceptance criteria for the operator's field of vision — Part 2: Field of vision to the side and to the rear) are met with relevant documentation included in the information document: yes/no ( 4 ) 20.   DRIVER INFORMATION SYSTEMS 20.1.   Requirements under ISO 15077:2008 (Tractors and self-propelled machinery for agriculture — Operator controls — Actuating forces, displacement, location and method of operation) Annex B on operator controls associated with virtual terminals are met with relevant documentation included in the information document: yes/no ( 4 ) 21.   INSTALLATION OF LIGHTING, LIGHT-SIGNALLING DEVICES, INCLUDING AUTOMATIC SWITCHING OF LIGHTING 21.1.   List of all devices (mentioning the number, make(s),type, component type-approval mark(s), the maximum intensity of the main-beam headlamps, colour, the corresponding tell-tale); the list may include several types of device for each function; in addition, the list may include in respect of each function the additional annotation ‘or equivalent devices’: … 21.2.   A diagram of the lighting and signalling installation as a whole, showing the position of the various devices on the vehicle: … 21.3.   Dimensioned sketches of the exterior of the vehicle showing the location of the lighting and light-signalling devices, number and colour of lights: … 21.4.   For every lamp and reflector, supply the following information: 21.4.1.   Drawing showing the extent of the illuminating surface: … 21.4.2.   Method used to define the apparent surface: … 21.4.3.   Axis of reference and centre of reference: … 21.4.4.   Method of operation of concealable lamps: … 21.5.   Description/drawing and type of headlamp levelling device (e.g. automatic, stepwise manually adjustable, continuously manually adjustable) ( 4 ): … 21.5.1.   Control device: … 21.5.2.   Reference marks: … 21.5.3.   Marks assigned for loading conditions: … 21.6.   For R- and S-category vehicles, description of the power connection for lighting and light-signalling devices: … 21.7.   Brief description of the electrical and/or electronic components used in the lighting system and in the light-signalling system: … 22.   VEHICLE OCCUPANT PROTECTION, INCLUDING INTERIOR FITTINGS AND OTHER WEATHER PROTECTION ARRANGEMENTS 22.1.    Bodywork 22.1.1.   Materials used and methods of construction: … 22.2.    Burning rate of cab material 22.2.1.   Burning rate not exceeding the maximum rate of 150 mm/min in accordance with the requirements under ISO 3795:1989 (Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials) with the relevant documentation included in the information document: yes/no ( 4 ). 22.3.    Interior protection for occupants 22.3.1.   Photographs, drawings and/or an exploded view of the interior fittings, showing the parts in the passenger compartment and the materials used (with the exception of interior rear view mirrors), arrangement of controls, seats and their rear parts, headrests, roof and opening roof, doors and window winders and other non-specified fittings: … 22.3.2.   For vehicles equipped with steering wheel and bench seats or bucket seats in more than one row, environment of the rear passenger seats, if fitted, complying with Annex XVII to Commission Delegated Regulation (EU) No 3/2014  ( 5 ) : yes/no ( 4 ) 22.4.    Head restraint(s) 22.4.1.   Provided: yes/no ( 4 ) 22.4.2.   Requirements under UNECE Regulation 25 ( OJ L 215, 14.8.2010, p. 1 ) are met with the relevant documentation included in the information document: yes/no ( 4 ) 22.4.3.   Type: integrated/detachable/separate ( 4 ) 22.4.4.   Detailed description of the head restraint, specifying in particular the nature of the padding material or materials and, where applicable, the position and specifications of the braces and anchorage pieces for the type of seat for which approval is sought: … 22.4.5.   In the case of a‘separate’ head restraint: 22.4.5.1.   Detailed description of the structural zone to which the head restraint is intended to be fixed: 22.4.5.2.   Scale drawings of the significant parts of the structure and the head restraint: … 22.5.    Foot rests 22.5.1.   Photographs and/or drawings of the operating space showing the true, effective number, location and dimensions of the footrests: … 22.6.    Other weather protection arrangements 22.6.1.   Description (Including photographs and drawings): … 22.6.2.   Internal and external dimensions: … mm × … mm × … mm … mm × … mm × … mm 23.   VEHICLE EXTERIOR AND ACCESSORIES 23.1.   General arrangement (drawing or photographs accompanied if necessary by dimensional details and/or text) indicating the position of the attached sections and views, of any parts of the exterior surface which can be regarded as critical for external projections, for example, and where relevant: bumpers, floor line, door and window pillars, air-intake grilles, radiator grille, windscreen wipers, rain gutter channels, handles, slide rails, flaps, door hinges and locks, hooks, eyes, winches, decorative trim, badges, emblems and recesses and any other parts of the exterior surface which can be regarded as critical with regard to the risk or seriousness of bodily injury to a person hit by the external surface or brushing against it in the event of a collision (e.g. lighting equipment): … 23.2.   A detailed description, including photographs and/or drawings, of the vehicle with respect to the structure, the dimensions, the relevant reference lines and the constituent materials of the frontal part of the vehicle (interior and exterior), including detail of any active pedestrian protection system installed: … … 23.3.   Drawing of the floor line: … 24.   ELECTRO-MAGNETIC COMPATIBILITY (EMC) 24.1.   Schedule describing all projected combinations of relevant vehicle electrical/electronic systems or ESAs, body styles ( 60 ), variations in body material, general wiring arrangements, engine variations, left-hand/right-hand drive versions and wheelbase versions: … 24.2.   Requirements under UNECE Regulation No 10 ( OJ L 254, 20.9.2012, p. 1 ) are met with the relevant documentation included in the information document: yes/no ( 4 ) 24.3.   Requirements under ISO 14982:1998 (Agricultural and forestry machinery — Electromagnetic compatibility — Test methods and acceptance criteria) are met with relevant documentation included in the information document: yes/no ( 4 ) 24.4.    Alternatively to entry 24.2 or entry 24.3, provide the following information: 24.4.1.   Description and drawings/photographs of the shapes and constituent materials of the part of the body forming the engine compartment and adjacent parts of the passenger compartment: … 24.4.2.   Drawings or photographs of the position of the metal components housed in the engine compartment (e.g. heating appliances, spare wheel, air filter, steering mechanism, etc.): … 24.4.3.   Table or drawing of radio-interference control equipment: … 24.4.4.   Particulars of the nominal value of the direct-current resistance, and, in the case of resistive ignition cables, of their nominal resistance per metre: … 25.   AUDIBLE WARNING DEVICE(S) 25.1.   Component type-approval for an audible warning device granted according to the requirements for N-category vehicles in the UNECE Regulation No 28 ( OJ L 323, 6.12.2011, p. 33 ), with relevant documentation included in the information document: yes/no ( 4 ) 25.2.   Summary description of device(s) used: … 25.3.   Drawing(s) showing the location of the audible warning device(s) in relation to the structure of the vehicle: … 25.4.   Details of the method of attachment, including the part of the vehicle structure to which the audible warning device(s) is (are) attached: … 25.5.   Electrical/pneumatic circuit diagram: … 25.5.1.   Voltage: AC/DC ( 4 ) 25.5.2.   Rated voltage or pressure: … 25.6.   Drawing of the mounting device: … 26.   HEATING SYSTEM AND AIR-CONDITIONING 26.1.   Heating system tested in accordance with section 8 of ISO 14269-2:1997 (Tractors and self-propelled machines for agriculture and forestry — Operator enclosure environment — Part 2: Heating, ventilation and air-conditioning test method and performance) and test reports are included in the information document: yes/no/not applicable ( 4 ) 26.2.   Air-conditioning system tested in accordance with section 9 of ISO 14269-2:1997 (Tractors and self-propelled machines for agriculture and forestry — Operator enclosure environment — Part 2: Heating, ventilation and air-conditioning test method and performance) and test reports are included in the information document: yes/no/not applicable ( 4 ) 26.3.   Alternatively to entries 26.1 to 26.2, requirements under UNECE Regulation 122 ( OJ L 164, 30.6.2010, p. 231 ) for vehicles of for N-category are met with the relevant documentation included in the information document: yes/no/not applicable ( 4 )) 26.4.    Heating system 26.4.1.   Overall drawing of the heating system giving its location on the vehicle (and the arrangement of the sound damping devices (including the position of the heat exchange points)): … 26.4.2.   Overall drawing of the heat-exchanger used in systems utilising the heat from the exhaust gases, or of the parts where that exchange takes place (in the case of heating systems using the heat provided by the engine cooling air): … 26.4.3.   Sectional drawing of the heat-exchanger or parts where heat exchange takes place, together with a statement of the wall thickness, of the materials used and the characteristics of their surface: … 26.4.4.   Specifications regarding the method of manufacture and technical data relating to other major components of the heating system, such as the fan: … 26.5.    Air-conditioning 26.5.1.   Brief description and schematic drawing of air-conditioning and its control system: … 26.5.2.   Gas used as refrigerant in the air-conditioning system: … 27.   DEVICES TO PREVENT UNAUTHORISED USE 27.1.    For T- and C-category vehicles 27.1.1.   Requirements under UNECE Regulation 62 ( OJ L 89, 27.3.2013, p. 37 ) are met with the relevant documentation included in the information document: yes/no/not applicable ( 4 ) 27.1.2.   Relevant requirements as prescribed for N2-category vehicles in points 2, 5 except point 5.6, 6.2 and 6.3, under UNECE Regulation No 18 ( OJ L 120, 13.5.2010, p. 29 ) are met with the relevant documentation included in the information document: yes/no/not applicable ( 4 ) 27.1.3.   Alternatively to entry 27.1.1 or entry 27.1.2, provide the following information: 27.1.3.1.   Detailed description, including photographs or drawings, of the protective device(s) and of the vehicle parts involved in its installation: … 27.1.3.2.   List of the main components comprising the protective device(s): … 27.2.    For R- and S-category vehicles 27.2.1.   Detailed description, including photographs or drawings, of the protective device(s) and of the vehicle parts involved in its installation: … 27.2.1.1.   List of the main components comprising the protective device(s): … 28.   REGISTRATION PLATE(S) SPACE 28.1.   Location of registration plate(s) (indicate variants where necessary; drawings may be used as appropriate): … 28.1.1.   Height above road surface, upper edge: front: … mm rear: … mm 28.1.2.   Height above road surface, lower edge: front: … mm rear: … mm 28.1.3.   Distance of the centre line from the longitudinal median plane of the vehicle: front: … mm rear: … mm 28.1.4.   Dimensions (length × width): front: … mm × … mm rear: … mm × … mm 28.1.5.   Inclination of the plane to the vertical: front: … degr. rear: … degr. 28.1.6.   Angle of visibility in the horizontal plane: front … degr rear: … degr. 29.   BALLAST MASSES 29.1.   Detailed technical description (including photographs or drawings with dimensions) of the ballast masses and how they are mounted on the tractor: … 29.1.   Number of sets of ballast masses: … 29.1.1.   Number of components on each set: Set 1: … Set 2: … Set … 29.2.   Mass of the components on each set: Set 1: … kg Set 2: … kg Set …:… kg 29.2.1.   Total mass of each set: Set 1: … kg Set 2: … kg Set …:… kg 29.3.   Total mass of ballast masses: … kg 29.3.1.   Distribution of these masses among the axles: … kg 29.4.   Material(s) and method of construction: … 30.   SAFETY OF ELECTRICAL SYSTEMS 30.1.   Brief description of the power circuit components installation and drawings/photographs showing the location of the power circuit components installation: … 30.2.   Schematic diagram of all electrical functions included in power circuit: … 30.3.   Working voltage(s) (V): … 30.4.   Description of protection against electric-shocks: … 30.5.   Fuse and/or circuit breaker yes/no/optional ( 4 ) 30.5.1.   Diagram showing the functional range: … 30.6.   Configuration of power wiring harness: … 30.7.    Generator 30.7.1.   Type: … 30.7.2.   Rated power: … VA 30.8.    All-electric vehicles 30.8.1.   For all-electric T2-, T3-, C2- or C3-category vehicles, requirements of Annex IV to Commission Delegated Regulation (EU) No 3/2014 are met, with relevant documentation included in the information document: yes/no/as far as practicable ( 4 ) (if as far as practicable, specify: …) 30.9.    Battery isolator 30.9.1.   Disconnection of the battery by: electronic system/ignition key/common tool/switch/other ( 4 ) (if other, specify: …) 31.   FUEL TANK(S) 31.1.   Drawing and technical description of the tank(s) with connections and lines of the breathing and venting system, locks, valves, fastening devices: … 31.2.   Drawing clearly showing the position of the tank(s) in the vehicle: … 31.3.   Drawing of the heat shield between tank and exhaust device: … 31.4.    Main fuel tank(s) 31.4.1.   Maximum capacity: … 31.4.2.   Materials used: … 31.4.3.   Fuel tank inlet: restricted orifice/label ( 4 ) … 31.4.4.   Measure(s) for charge dissipation (if any): … 31.5.    Reserve fuel tank(s) 31.5.1.   Maximum capacity: … 31.5.2.   Materials used: … 31.5.3.   Fuel tank inlet: restricted orifice/label ( 4 ) … 31.5.4.   Measure(s) for charge dissipation (if any): … 32.   LATERAL AND REAR PROTECTION 32.1.    Lateral protection 32.1.1.   Presence: yes/no/incomplete ( 4 ) 32.1.2.   Drawing of the vehicle parts relevant to the lateral protection, i.e. drawing of the vehicle and/or chassis with position and mounting of the axle(s), drawing of the mountings and/or the fittings of lateral protection device(s). If the lateral protection is achieved without lateral protection device(s) the drawing shall clearly show that the required dimensions are met: … 32.1.3.   Drawing of the floor line at the vehicle lateral: … 32.1.4.   Drawings of the necessary sections through the external surface to measure the height (H) of the external surface projections in accordance with Appendix 1 to Annex XXVII to Commission Delegated Regulation (EU) 2015/208: … 32.1.5.   In the case of lateral protection device(s), full description and/or drawing of such device(s) (including mountings and fittings) or its/their component type-approval number(s): … 32.1.5.1.   Materials used: … 32.1.5.2.   Complete details of fittings required and full instructions, including torque requirements, for fitting: … 32.1.6.   Requirements under points 2 and 3 and Parts I, II and III of UNECE Regulation No 73 ( OJ L 122, 8.5.2012, p. 1 ) are met with relevant documentation included in the information document: yes/no ( 4 ) 32.2.    Rear protective structure 32.2.1.   Presence: yes/no/incomplete ( 4 ) 32.2.2.   Drawing of the vehicle parts relevant to the rear protective structure, i.e. drawing of the vehicle and/or chassis with position and mounting of the widest rear axle, drawing of the mounting and/or fitting of the rear protective structure. If the rear protective structure is not a special device, the drawing shall clearly show that the required dimensions are met: … 32.2.3.   Drawing of the floor line at the vehicle rear end: … 32.2.4.   In case of a special device, full description and/or drawing of the rear protective structure (including mountings and fittings), or, if approved as separate technical unit, type-approval number: … 32.2.4.1.   Materials used: … 32.2.4.2.   Complete details of fittings required and full instructions, including torque requirements, for fitting: … 33.   LOAD PLATFORM(S) 33.1.    Load platform(s) dimensions 33.1.1.   Length of the load platform(s): … mm 33.1.2.   Width of load platform(s): … mm 33.1.3.   Height of load platform(s) above the ground ( 47 ): … mm 33.2.   Safe load carrying capacity of load platform(s) declared by manufacturer: … kg 33.2.1.   Distribution of this (these) load(s) among the axles: … kg 33.3.   For T- and C-category vehicles, detachable platform(s): yes/no/optional ( 4 ) 33.3.1.   Description of the devices for attachment to the vehicle: … 33.4.    Stability of the load platform 33.4.1.   Position of centre of gravity of the platform(s) in the longitudinal, transverse and vertical direction: … 33.4.2.   For vehicles with multiple load platforms, position of the centre of gravity of the vehicle with loaded platform(s) and without driver in the longitudinal, transverse and vertical direction: … 34.   FRONT TOWING DEVICE (T-AND C-CATEGORY VEHICLES) 34.1.   Dimensioned drawing of the front towing device and of the securing device: … 34.2.   For vehicles equipped with a maximum technically permissible mass not exceeding 2 000 kg, requirements of Commission (EU) Regulation No 1005/2010 ( OJ L 291, 9.11.2010, p. 36 ) are met, with the relevant documentation included in the information document: yes/no ( 4 ) 35.   TYRES 35.1.   Type-approved in accordance with Annex XXX to Commission Delegated Regulation (EU) 2015/208: yes/no/not applicable ( 4 ) 35.2.   Type-approved in accordance with Regulation (EC) No 661/2009 of the European Parliament and of the Council ( OJ L 200, 31.7.2009, p. 1 ): yes/no/not applicable ( 4 ) 35.3.   Approved in accordance with UNECE Regulation No 106 ( OJ L 257, 30.9.2010, p. 231 ): yes/no/not applicable ( 4 ) 35.4.   Approved in accordance with UNECE Regulation No 30 ( OJ L 307, 23.11.2011, p. 1 ): yes/no/not applicable ( 4 ) 35.5.   Approved in accordance with UNECE Regulation No 54 ( OJ L 307, 23.11.2011, p. 2 ): yes/no/not applicable ( 4 ) 35.6.   Approved in accordance with UNECE Regulation No 75 ( OJ L 84, 30.3.2011, p. 46 ): yes/no/not applicable ( 4 ) 35.7.   Approved in accordance with UNECE Regulation No 117 ( OJ L 307, 23.11.2011, p. 3 ): yes/no/not applicable ( 4 ) 36.   SPRAY-SUPPRESSION SYSTEM 36.1.    Wheel guards 36.1.1.   Vehicle fitted with wheel guards: yes/no ( 4 ) 36.1.2.   Brief description of the vehicle with regard to its wheel guards: … 36.1.3.   Detailed drawings of the wheel guards and their position on the vehicle showing the dimensions and taking account of the extremes of tyre/wheel combinations: … 36.2.    Other spray-suppression devices 36.2.1.   Presence: yes/no/incomplete ( 4 ) 36.2.2.   Brief description of the vehicle with regard to its spray-suppression system and the constituent components: … 36.2.3.   Detailed drawings of the spray-suppression system and its position on the vehicle showing the dimensions and taking account of the extremes of tyre/wheel combinations: … 37.   CRAWLER UNDERCARRIAGE (provide also entry 4.1.2.3) 37.1.   Photographs and dimensioned drawings of the arrangement of the crawler undercarriage and its installation on the vehicle (including the elements inside of track belts to ensure that the track belt is guided over the rollers and the track pattern in the outside): … 37.2.   Type of material in contact with the surface: rubber tracks/steel tracks/rubber pads on the track shoes ( 4 ) 37.3.    Metallic tracks 37.3.1.   Number of track rollers directly transferring load onto the road surface (N R ): … 37.3.2.   Outer surface area of each pad (A P ): … mm 2 37.4.    Rubber tracks 37.4.1.   Total surface area of rubber lugs in contact with the road (A L ): … mm 2 37.4.2.   Percentage of lug area versus the total surface of the belt: … % 38.   MECHANICAL COUPLING 38.1.    Photographs and dimensional drawings of the mechanical coupling, its installation on the vehicle and its coupling with the device installed on the towed vehicle: 38.1.1.   Rear mechanical coupling: yes/no ( 4 ) 38.1.2.   Front coupling device (for R- and S-category vehicles): yes/no ( 4 ) 38.2.    Short technical description of the mechanical coupling specifying the type of construction and the material used 38.2.1.   Rear mechanical coupling: … 38.2.2.   Front coupling device (for R- and S-category vehicles): … 38.3.   Rear mechanical coupling Type (according to Appendix 1 to Annex XXXIV to Commission Delegated Regulation (EU) 2015/208): … … … Make: … … … Manufacturer's type designation: … … … (EU) type-approval mark or -number: … … … Maximum horizontal load/D-Value ( 4 ) ( 44 ): … kg/kN ( 4 ) … kg/kN ( 4 ) … kg/kN ( 4 ) Towable mass (T) ( 4 ) ( 44 ): … tonnes … tonnes … tonnes Maximum permissible vertical load on the coupling point ( 44 ): … kg … kg … kg Position of coupling point ( 62 ) height above ground, minimum … mm … mm … mm maximum … mm … mm … mm distance from vertical plane passing through the axis of the rear axle minimum … mm … mm … mm maximum … mm … mm … mm 38.4.   Front coupling device (for R- and S-category vehicles): Type (according to Appendix 1 to Annex XXXIV to Commission Delegated Regulation (EU) 2015/208): … … … Make: … … … Manufacturer's type designation: … … … (EU) type-approval mark or -number: … … … Maximum horizontal load/D-Value ( 4 ) ( 44 ): … kg/kN ( 4 ) … kg/kN ( 4 ) … kg/kN ( 4 ) Towable mass (T) ( 4 ) ( 44 ): … tonnes … tonnes … tonnes Maximum permissible vertical load on the coupling point ( 44 ): … kg … kg … kg Position of coupling point ( 62 ) height above ground, minimum … mm … mm … mm maximum … mm … mm … mm 38.5.   Description of the mechanical coupling: Type (according to Appendix 1 to Annex XXXIV to Commission Delegated Regulation (EU) 2015/208): … Make: … Manufacturer's type designation: … Maximum horizontal load/D-Value ( 4 ) ( 44 ): … kg/kN ( 4 ) Towable mass (T) ( 4 ) ( 44 ): … tonnes Vertical load on the coupling point (S) ( 44 ): … kg Photographs and scale drawings of the coupling device. These drawings shall in particular show the required dimensions in detail as well as the measurements for mounting the device.   Short technical description of the coupling device specifying the type of construction and the material used.   Type of Test Static/Dynamic ( 4 ) (EU) type-approval mark or -number of — drawbar eyes, coupling heads or similar coupling devices that shall be attached to the mechanical coupling (in the case of hinged or rigid drawbars) — type-approval mark or -number of mechanical couplings that shall be attached to the ladder frame/trailer hitch support (if restricted to certain types): … 38.6.   Component type-approval for a mechanical coupling granted under UNECE Regulation No 55 ( OJ L 227, 28.8.2010, p. 1 ), with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 39.   THREE-POINT LIFTING MECHANISM 39.1.   Three-point lifting mechanism: front mounted/rear mounted/both front and rear mounted/inexistent ( 4 ) 40.   ADDITIONAL COUPLING POINTS 40.1.   Additional coupling points: yes/no/optional ( 4 ) 40.2.   Detailed technical description (including photographs or drawings) and main purpose(s) of the additional coupling points: … 40.3.   Maximum permissible vertical load on the additional coupling points: … kg D.    INFORMATION ON BRAKING PERFORMANCE 41.   SUSPENSION 41.1.   Brief description and schematic drawing of suspension and its control system for of each axle or group of axles or wheel: … 41.2.   Drawing of the suspension arrangements: … 41.3.   Level adjustment: yes/no/optional ( 4 ) 41.4.   Brief description of the electrical/electronic components: … 41.5.   Air-suspension for driving axle(s): yes/no ( 4 ) 41.5.1.   Suspension of driving axle(s) equivalent to air-suspension: yes/no ( 4 ) 41.5.2.   Frequency and damping of the oscillation of the sprung mass: … 41.6.   Air-suspension for non-driving axle(s): yes/no ( 4 ) 41.6.1.   Suspension of non-driving axle(s) equivalent to air-suspension: yes/no ( 4 ) 41.6.2.   Frequency and damping of the oscillation of the sprung mass: … 41.7.   Characteristics of the springing parts of the suspension (design, characteristics of the materials and dimensions): … 41.8.   Vehicle equipped with hydro-pneumatic/hydraulic/pneumatic ( 4 ) suspension: yes/no ( 4 ) 41.9.   Stabilisers: yes/no/optional ( 4 ) 41.10.   Shock absorbers: yes/no/optional ( 4 ) 41.11.   Other devices (if any): … 42.   AXLE(S) AND TYRES 42.1.   Description (including photographs and drawings) of the axle(s): … 42.2.   Material(s) and method of construction: … 42.3.   Make (where appropriate): … 42.4.   Type (where appropriate): … 42.5.   Maximum permissible mass supported by the axle(s): … kg 42.6.   Axle(s) dimensions: 42.6.1.   Length: … mm 42.6.2.   Width: … mm 42.7.   Braking connection to the axle(s): axial/radial/integrated/other ( 4 ) (if other, specify: …) 42.8.   Dimensions of the largest permissible tyres on braked axles: … 42.8.1.   Nominal rolling circumference of the largest tyres on braked axles: … 42.8.2.   Dimensions of the largest permissible tyres on powered axles: … 42.8.3.   Nominal rolling circumference of the of the largest tyres on powered axles: … 43.   BRAKING 43.1.   Brief description of the braking system(s) installed on the vehicle (according to point 1.6 of the Addendum of Appendix 1 to Annex XIII to Commission Delegated Regulation (EU) 2015/68) 43.2.   Specifications of the vehicle with respect to the control circuits of the pneumatic and/or electric control lines of the braking system(s) and a list of the supported messages and parameters: … 43.3.   Braking system(s) interface complying with ISO 11992-1:2003 (Road vehicles — Interchange of digital information on electrical connections between towing and towed vehicles — Part 1: Physical and data-link layers), including the physical layer, the data link layer and the application layer and the respective position of supported messages and parameters: yes/no ( 4 ) 43.4.    Braking system(s) 43.4.1.   Description of the braking system(s) operation (including any electronic parts), electric block diagram, hydraulic or pneumatic circuit plan ( 55 ): … 43.4.2   Schematic drawing and operating sketch of the braking system(s) ( 55 ): … 43.4.3.   List of braking-system components, properly identified ( 55 ): … 43.4.4.   Technical explanation on the calculation for the braking system(s) (determination of the ratio of the total braking forces at the circumference of the wheels to the force applied to the braking control) ( 55 ): … 43.4.5.   External energy source(s) (if any) (characteristics, capacity of energy reservoirs, maximum and minimum pressure, pressure gauge and minimum-pressure warning device on the dashboard, vacuum reservoirs and supply valve, supply compressors, compliance with provisions regarding pressure equipment) ( 55 ): … 43.4.6.   Electronic braking system: yes/no/optional ( 4 ) 43.4.7.   Type-I test report number(s), in accordance with Annex VII to Commission Delegated Regulation (EU) 2015/68 (if applicable): … 43.5.    Braking transmission 43.5.1.   Braking transmission: mechanical/hydrostatic without power assistance/power-assisted/fully powered transmission ( 4 ) 43.5.2.   Transmission technology: pneumatic/hydraulic/both pneumatic and hydraulic ( 4 ) 43.5.3.   Locking of left and right braking controls: … 43.6.    Towed vehicle braking devices 43.6.1.   Towed vehicle braking control system technology: Hydraulic/Pneumatic/Electric ( 4 ) 43.6.2.   Towed vehicle-brake actuating device (description, characteristics): … 43.6.3.   Description of the connectors, couplings and safety devices (including drawings, sketches and the identification of any electronic parts): … 43.6.4.   Connections type: single line/two-lines ( 4 ) 43.6.4.1.   Supply overpressure (1 line): … kPa 43.6.4.2   Supply overpressure (2 line) (if applicable): … kPa 43.6.4.2.1.   Hydraulic: … kPa 43.6.4.2.2.   Pneumatic: … kPa E.    INFORMATION ON VEHICLE CONSTRUCTION 44.   CONFORMITY OF PRODUCTION 44.1.   Description of overall quality-assurance management systems: … 45.   ACCESS TO VEHICLE ON BOARD DIAGNOSTIC (OBD) AND VEHICLE REPAIR AND MAINTENANCE INFORMATION ( 45 ) 45.1.   Address of principal website for access to vehicle repair and maintenance information ( 45 ): … 45.2.   In the case of multi-stage type-approval, address of principal website for access to vehicle repair and maintenance information from manufacturer(s) at previous stage(s) ( 45 ): … 45.3.   Relevant information to enable the development of replacement components which are critical to the correct functioning of the OBD system provided: yes/no ( 4 ) 45.4.   Annual worldwide production of a type ( 61 ): … 45.5.   Proof(s) of compliance that vehicle repair and maintenance information is provided using only open text and graphic formats or formats which can be viewed and printed using only standard software plug-ins that are freely available, easy to install, and which run with computer operating systems commonly in use. 45.5.1.   Keywords in the metadata conform to ISO 15031-2:2010 (Road vehicles — Communication between vehicle and external equipment for emissions-related diagnostics — Part 2: Guidance on terms, definitions, abbreviations and acronyms): yes/no ( 4 ) 45.6.    Reprogramming of control units in accordance with point 2.5 of Appendix 1 to Annex V to Commission Delegated Regulation (EU) No 1322/2014 45.6.1.   Reprogramming of control units conducted in accordance with: /SAE J2534/TMC RP1210/other non-proprietary software ( 4 ) (if other non-proprietary software, specify: …) 45.6.1.1.   Proprietary software: yes/no ( 4 ) 45.6.1.2.   ISO 22900-2 (Road vehicles — Modular vehicle communication interface (MVCI) — Part 2: Diagnostic protocol data unit application programming interface (D-PDU API)): yes/no ( 4 ) 45.6.1.3.   SAE J2534 (Recommended practice for pass-thru vehicle programming): yes/no ( 4 ) 45.6.1.4.   TMC RP1210 (API): yes/no ( 4 ) 45.6.1.5.   Other non-proprietary software: yes/no ( 4 ) (if other non-proprietary software, specify: …) 45.6.2.   Compatibility validation of manufacturer-specific application and vehicle communication interfaces (VCIs) is made by: independently developed VCIs/loan of special hardware ( 4 ) 45.6.3.   In-vehicle communication and communication between ECUs and diagnostic service according to standard: 45.6.3.1.   SAE J1939 (Serial control and communications vehicle network): yes/no ( 4 ) 45.6.3.2.   ISO 11783 (Tractors and machinery for agriculture and forestry — Serial control and communications data network): yes/no ( 4 ) 45.6.3.3.   ISO 14229 (Road vehicles — Unified diagnostic services (UDS)): yes/no ( 4 ) 45.6.3.4.   ISO 27145 (Road vehicles — Implementation of World-Wide Harmonized On-Board Diagnostics (WWH-OBD) communication requirements) in combination with ISO 15765-4 (Road vehicles — Diagnostic communication over Controller Area Network (DoCAN) — Part 4: Requirements for emissions-related systems) ( 4 )/ISO 13400 (Road vehicles — Diagnostic communication over Internet Protocol (DoIP)) ( 4 ): yes/no ( 4 ) 45.7.    Information required for the manufacture of diagnostic tools 45.7.1.   The vehicle manufacturer uses diagnostic and test tools in accordance with ISO 22900-2:2009 (Road vehicles — Modular vehicle communication interface (MVCI) — Part 2: Diagnostic protocol data unit application programming interface (D-PDU API)) and ISO 22901-2:2011 (Road vehicles — Open diagnostic data exchange (ODX) — Part 2: Emissions-related diagnostic data) in their franchised networks: yes/no/not applicable ( 4 ) (if not applicable: specify reasons: …) 45.7.2.   ODX files are accessible to independent operators via the manufacturer's website: yes/no/not applicable ( 4 ) (if not applicable: specify reasons: …) 45.7.3.   Communication protocol information as laid down in point 1.1 of Appendix 2 to Annex V to Commission Delegated Regulation (EU) No 1322/2014 are made available through manufacturer's repair information websites: yes/no/not applicable ( 4 ) (if not applicable: specify reasons: …) 45.7.4.   Information required for the test and diagnosis of OBD monitored components as laid down in point 1.2 of Appendix 2 to Annex V to Commission Delegated Regulation (EU) No 1322/2014 is made available through manufacturer's repair information websites: yes/no/not applicable ( 4 ) (if not applicable: specify reasons: …) 45.7.5.   Data required to perform the repair as laid down in point 1.3 of Appendix 2 to Annex V to Commission Delegated Regulation (EU) No 1322/2014 are made available through manufacturer's repair information websites: yes/no/not applicable ( 4 ) (if not applicable: specify reasons: …) 45.8.    Repair and maintenance information of vehicle combinations 45.8.1   The vehicle manufacturer recommends the combination of a type of tractor with a type of R or S category vehicle or vice versa: yes/no ( 4 ) 45.8.2.   Vehicles for which the combination is recommended: 45.8.2.1.   Make (trade name of manufacturer) ( 18 ): … 45.8.2.2.   Type ( 17 ): … 45.8.2.2.1.   Variant(s) ( 17 ): … 45.8.2.2.2.   Version(s) ( 17 ): … 45.8.2.3.   Commercial name(s) (if available): … 45.8.2.4.   Category, subcategory and speed index of the vehicle ( 2 ): … 45.8.3.   Vehicle OBD and vehicle repair and maintenance information related to the interconnectivity of both vehicles provided through a website set up jointly by several manufacturers or a consortium of manufacturers: yes/no ( 4 ) 45.8.3.1.   Address of the website set up jointly by several manufacturers or a consortium of manufacturers ( 45 ): … 46.   ROLL-OVER PROTECTIVE STRUCTURE (ROPS) 46.1.   Equipment of ROPS: compulsory/optional/standard ( 4 ) 46.2.   ROPS by cab/by frame/by roll bar(s) mounted at front/rear ( 4 ) 46.2.1.   In the case of roll bar: fold-down/not fold down ( 4 ) 46.2.2.   In the case of foldable roll bar: 46.2.2.1.   Folding: with tools/folding without tools ( 4 ); 46.2.2.2.   Locking mechanism: manual/automatic ( 4 ) 46.2.2.3.   Photographs and detailed technical drawings showing the grasping area and a lateral and top view of the accessible zones. The dimensions must figure on the drawings: … 46.3.   Photographs and detailed technical drawings showing the position of the ROPS, position of the seat index point (SIP), the details of mountings and position of the front part of the tractor capable of supporting the tractor when overturned (if necessary) etc. (in the case of front-mounted foldable ROPS, show the grasping area and a lateral and top view of the accessible zones). The main dimensions must figure on the drawings, including external dimensions of tractor with protective structure fitted and main interior dimensions: … 46.4.   Brief description of the protective structure, comprising: 46.4.1.   Type of construction: … 46.4.2.   Details of mountings: … 46.4.3.   Details of the front part of the tractor capable of supporting the tractor when overturned (if necessary): … 46.4.4.   Additional frame: … 46.5.    Dimensions ( 52 ) 46.5.1.   Height of roof members above the seat index point (SIP): … mm 46.5.2.   Height of roof members above the tractor footplate: … mm 46.5.3.   Interior width of the protective structure vertically above the seat index point at the level of centre of the steering wheel: … mm 46.5.4.   Distance from the centre of the steering wheel to the right-hand side of the protective structure: … mm 46.5.5.   Distance from the centre of the steering wheel to the left-hand side of the protective structure: … mm 46.5.6.   Minimum distance from the steering wheel rim to the protective structure: … mm 46.5.7.   Horizontal distance from the seat index point to the rear of the protective structure above the seat index point: … mm 46.5.8.   Position (with reference to the rear axle) of the front part of the tractor capable of supporting the tractor when overturned (if necessary): 46.5.8.1.   Horizontal distance: … mm 46.5.8.2.   Vertical distance: … mm 46.6.    Details of materials used in the construction of the protective structure and specifications of steels used ( 53 ) 46.6.1.   Main frame (parts — material — sizes): … 46.6.2.   Mountings (parts — material — sizes): … 46.6.3.   Assembly and mounting bolts (parts — sizes): … 46.6.4.   Roof (parts — material — sizes): … 46.6.5.   Cladding (if equipped) (parts — material — sizes): … 46.6.6.   Glass (if equipped) (parts — material — sizes): … 46.6.7.   Front part of the tractor capable of supporting the tractor when overturned (if necessary) (parts — material — sizes): … 46.7.    Alternatively to entries 46.1 to 46.6.7, provide the following information: 46.7.1.   Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry tractors (dynamic test), OECD Code 3, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 46.7.2.   Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry track-laying tractors, OECD Code 8, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 46.7.3.   Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry tractors (static test), OECD Code 4, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 46.7.4.   Complete test report issued on the basis of the OECD standard Code for the official testing of front mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 6, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 46.7.5   Complete test report issued on the basis of the OECD standard Code for the official testing of rear mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 7, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 47.   FALLING OBJECT PROTECTIVE STRUCTURES (FOPS) 47.1.    T- and C-category vehicles equipped for forestry applications 47.1.1.   Requirements under standard ISO 8083:2006 (Machinery for forestry — Falling-object protective structures (FOPS) — Laboratory tests and performance requirements) level I/level II ( 4 ) on FOPS are met with relevant documentation included in the information document: yes/no ( 4 ) 47.2.    All other T- and C-category vehicles fitted with FOPS 47.2.1.   Photographs and detailed technical drawings showing the position of the FOPS, position of the seat index point (SIP), etc. The main dimensions must figure on the drawings, including external dimensions of tractor with protective structure fitted and main interior dimensions: 47.2.2.   Brief description of the protective structure, comprising: 47.2.2.1.   Type of construction: … 47.2.2.2.   Details of mountings: … 47.2.3.    Dimensions ( 52 ) 47.2.3.1.   Height of roof members above the seat index point (SIP): … mm 47.2.3.2.   Height of roof members above the tractor footplate: … mm 47.2.3.3.   Overall height of the tractor with the protective structure fitted: … mm 47.2.3.4.   Overall width of the protective structure (if mudguards are included, this is to be stated): … mm 47.2.4.    Details of materials used in the construction of the protective structure and specifications of steels used ( 53 ) 47.2.4.1.   Main frame (parts — material — sizes): … 47.2.4.2.   Mountings (parts — material — sizes): … 47.2.4.3.   Assembly and mounting bolts (parts — sizes): … 47.2.4.4.   Roof (parts — material — sizes): … 47.2.5.   Details of tractor manufacturer's reinforcements on original parts: … 47.2.6.   Alternatively to entries 47.2.1 to 47.2.5, a complete test report issued on the basis of the OECD standard Code for the official testing of falling object protective structures on agricultural and forestry tractors, OECD Code 10, Edition 2015 of July 2014 is provided with relevant documentation included in the information document: yes/no ( 4 ) 48.   DRIVER'S EXPOSURE TO NOISE LEVEL 48.1.   T- or C-category (with rubber tracks) vehicles to be tested in accordance with Test method 1, in accordance with point 2 of Annex XIII to Commission Delegated Regulation (EU) No 1322/2014: yes/no/not applicable ( 4 ) 48.2.   T- or C-category (with rubber tracks) vehicles to be tested in accordance with Test method 2, in accordance with point 3 of Annex XIII to Commission Delegated Regulation (EU) No 1322/2014: yes/no/not applicable ( 4 ) 48.3.   C-category vehicles with steel tracks to be tested on a layer of humid sand as specified by paragraph 5.3.2 of ISO 6395:2008 (Earth-moving machinery — Determination of sound power level — Dynamic test conditions): yes/no/not applicable ( 4 ) 48.4   Alternatively to entries 48.1 to 48.3, a complete test report issued on the basis of the OECD standard Code for the official measurement of noise at the driving position(s) on agricultural and forestry tractors, OECD Code 5, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 49.   SEATING POSITIONS (SADDLES AND SEATS) 49.1.   Seating position configuration: seat/saddle ( 4 ) 49.2.   Coordinates or drawing of the Seat Reference point(s) (S) of all seating positions: … 49.3.   Description and drawings of: 49.3.1.   The seats and their anchorages: … 49.3.2.   The adjustment system: … 49.3.3.   The displacement and locking systems: … 49.3.4.   The seat-belt anchorages (if incorporated in the seat structure): … 49.3.5.   The parts of the vehicle used as anchorages: … 49.4.    Driver's seat 49.4.1.   Position of the driving seat: left/right/centre ( 4 ): … 49.4.2.   Driver's seat type category: category A class I/II/III, category B ( 4 ) 49.4.3.   Reversible driving position: yes/no ( 4 ) 49.4.3.1.   Description of the reversible driving position: … 49.4.4.   Dimensions of the driving seat, including the depth and width of the seat surface, the position and inclination of the backrest, as well as the inclination of the seat surface: 49.4.5.   Main characteristics of the driving seat: … 49.4.6.   Adjustment system: … 49.4.7.   Displacement and locking system in the longitudinal and vertical directions: … 49.4.7.1.   In the case of vehicles not equipped with an adjustable seat, indicate the displacement of the steering column and pedal(s): … 49.5.    Passenger seat(s) 49.5.1.   Location and arrangement ( 8 ): … 49.5.2.   Dimensions of the passenger seat(s): … 49.5.3.   Main characteristics of the passenger seat(s): … 49.5.4.   Requirements under standard EN 15694:2009 (Agricultural and forestry tractors. Passenger seat. Requirements and test procedures) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 49.5.5.   Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs — Quads). Safety requirements and test methods) on passenger seats for ATV Type II vehicle are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 50.   OPERATING SPACE AND ACCESS TO AND EXIT OF THE VEHICLE INCLUDING DOORS AND WINDOWS 50.1.    Operating space 50.1.1.   Detailed photographs or drawings, including dimensions of the operating space, indicating in particular the position of the Seat reference point (S) and the dimensions of the operating space around it, the clearance between the base of the steering wheel and the fixed parts of the tractor, the locations of the control devices, rungs and necessary handrails: … 50.1.2.   Hand-operated control devices have the minimum clearances required by point 4.5.3 of ISO 4254-1:2013 (Agricultural machinery — Safety — Part 1: General requirements) with relevant documentation included in the information document: yes/no ( 4 ) 50.2.    Access to the driving position: 50.2.1.   Detailed photographs or drawings and/or an exploded view, including dimensions of entrances, steps, rungs, handrails and handholds: … 50.2.2.   Minimum dimensions of steps, integral foot recesses and rungs: 50.2.2.1.   Depth clearance: … mm 50.2.2.2.   Width clearance: … mm 50.2.2.3.   Height clearance: … mm 50.2.2.4.   Distance between surface of two steps: … mm 50.2.3.   For C-category vehicles, requirements under section 3.3.5 of Annex XV to Commission Delegated Regulation (EU) No 1322/2014 are met with relevant documentation included in the information document: yes/no ( 4 ) 50.2.4.   Handrails/handholds ( 4 ) provided: yes/no ( 4 ) 50.3.    Access to other positions than the driving position: 50.3.1.   Detailed photographs or drawings and/or an exploded view, including dimensions of entrances, steps, rungs, handrails and handholds: … 50.3.2.   Minimum dimensions of steps, integral foot recesses and rungs: 50.3.2.1.   Depth clearance: … mm 50.3.2.2.   Width clearance: … mm 50.3.2.3.   Height clearance: … mm 50.3.2.4.   Distance between surface of two steps: … mm 50.3.3.   Handrails/handholds ( 4 ) provided: yes/no ( 4 ) 50.4.    Occupant doors, latches and hinges 50.4.1.   Number of doors, and its configuration, dimensions and maximum angle of opening ( 5 ): … 50.4.2.   Drawing of latches and hinges and of their position in the doors: … 50.4.3.   Technical description of latches and hinges: … 50.4.4.   Vehicle doors, with powered windows and powered roof hatches, if fitted, complying with paragraphs 5.8.1 to 5.8.5 of UNECE Regulation No 21( OJ L 188, 16.7.2008, p. 32 ): yes/no ( 4 ) 50.5.    Windows and emergency exit(s) 50.5.1.   Photographs or drawings and/or an exploded view of the arrangement of windows and emergency exits, as well as of any additional means to facilitate the evacuation: … 50.5.2.   Number of windows: … and of emergency exits: … 50.5.3.   Dimensions of windows: … mm × … mm and of emergency exits: … mm × … mm 50.5.4.   Means to overcome differences in height exceeding 1 000 mm to facilitate the evacuation, if fitted: … 51.   POWER TAKE-OFF(S) 51.1.   Number of power take-offs: … 51.2.    Main power take-off 51.2.1.   Position: front/rear/other ( 4 ) (if other specify: …) 51.2.2.   Revolutions per minute: … 51.2.2.1.   Ratio of power take-off revolutions to that of the engine: … 51.2.4.   Optional: Power at the power take-off (PTO) at the rated speed(s) (in accordance with OECD Code 2 ( 57 ) or ISO 789-1:1990 (Agricultural tractors — Test procedures — Part 1: Power tests for power take-off)) Rated speed PTO (min – 1 ) Corresponding engine speed (min – 1 ) Power (kW) 1-540 … … 2-1 000 … … 540E     1 000 E     51.2.3.   Power take-off guard (description, dimensions, drawings, photographs): … 51.3.    Secondary power take-off (if any) 51.3.1.   Position: front/rear/other ( 4 ) (if other specify: …) 51.3.2.   Revolutions per minute: … 51.3.2.1.   Ratio of power take-off revolutions to that of the engine: … 51.2.3.   Optional: Power at the power take-off (PTO) at the rated speed(s) (in accordance with OECD Code 2 ( 57 ) or ISO 789-1:1990 (Agricultural tractors — Test procedures — Part 1: Power tests for power take-off)) Rated speed PTO (min – 1 ) Corresponding engine speed (min – 1 ) Power (kW) 1-540 … … 2-1 000 … … 540E     1 000 E     51.3.4.   Power take-off guard(s) (description, dimensions, drawings, photographs): … 51.4.    Rear power take-off 51.4.1.   Requirements under standard ISO 500-1:2014 (Agricultural tractors — Rear-mounted power take-off types 1, 2, 3 and 4 — Part 1: General specifications, safety requirements, dimensions for master shield and clearance zone) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 51.4.2.   Requirements under standard ISO 500-2:2004 (Agricultural tractors — Rear-mounted power take-off types 1, 2 and 3 — Part 2: Narrow-track tractors, dimensions for master shield and clearance zone) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 51.5.    Front power take-off 51.5.1.   Requirements under standard ISO 8759-1:1998 (Agricultural wheeled tractors — Front-mounted equipment — Part 1: Power take-off and three-point linkage), with the exception of its clause 4.2, are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 52.   PROTECTION OF DRIVE COMPONENTS, EXHAUST SYSTEM, GUARDS AND PROTECTIVE DEVICES 52.1.   Description (including drawings, sketches or photos) of the protection devices with dimensions showing the safety distances for avoiding contact with dangerous parts and the protective devices fitted for protection on dangerous points, at least for the following components: 52.1.1.   Control devices: … 52.1.2.   Rear three point lifting mechanism: … 52.1.3.   Front three point lifting mechanism: … 52.1.4.   Driving seat and environment: … 52.1.5.   Passenger seat(s) (if any): … 52.1.6.   Steering and swing axle: … 52.1.7.   Transmission shafts fixed on the tractor: … 52.1.8.   Clearance zone around the drive wheels: … 52.1.9.   Engine hood: … 52.1.10.   Protection against hot surfaces: … 52.1.11.   Exhaust system: … 52.1.12.   Wheels: … 52.2.   Description (including photographs and drawings, if necessary) of the protective devices employed for: 52.2.1.   Single surface protection: … 52.2.2.   Multi-surface protection: … 52.2.3.   Protection by total encapsulation: … 52.2.4.   Brief description of the electrical/electronic components (if any): … 52.3.   Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs — Quads). Safety requirements and test methods) on hot surfaces are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 52.4.   Description (including drawings, sketches or photos) of the layout and marking of flexible hydraulic hoses: … 52.5.   For R-category vehicles with tipping capability, description (including drawings, sketches or photos) of the support devices for service and maintenance: … 52.6.   Description and identification (including drawings, sketches or photos) of the greasing points and the means to access them: … 53.   SEAT-BELT ANCHORAGES 53.1.   Requirements under standard ISO 3776-1:2006 (Tractors and machinery for agriculture — Seat belts — Part 1: Anchorage location requirements) are met with relevant documentation included in the information document: yes/no ( 4 ) 53.2.   Photographs and/or drawings of the bodywork showing the true, effective location and dimensions of the anchorages: … 53.3.   Drawings of the anchorages and the parts of the vehicle structure to which they are attached (together with a statement on the nature of the materials used): … 53.4.    Designation of the types of belts ( 14 ) authorised for attachment to the anchorages on the vehicles   Anchorage location Vehicle structure Seat structure Driver's seat   Lower anchorages   outboard inboard     Upper anchorages     Passenger seat 1   Lower anchorages   outboard inboard     Upper anchorages     Passenger seat …   Lower anchorages   outboard inboard     Upper anchorages     53.4.1.   Observation: … 53.5.   Special devices (example: seat-height adjustment, preloading device, etc.): … 53.6.   Description of a particular type of safety belt where an anchorage is located in the seat backrest or incorporates an energy dissipating device: … 53.7.    Alternative to entries 53.2 to 53.6. 53.7.1.   Requirements under standard ISO 3776-2:2013 (Tractors and machinery for agriculture — Seat belts — Part 2: Anchorage strength requirements) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 53.7.2.   Test report granted a on the basis of UNECE Regulation No 14 ( OJ L 109, 28.4.2011, p. 1 ) with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 53.7.3.   Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry tractors (dynamic test), OECD Code 3 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 53.7.4.   Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry track-laying tractors, OECD Code 8 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 53.7.5.   Complete test report issued on the basis of the OECD standard Code for the official testing of protective structures on agricultural and forestry tractors (static test), OECD Code 4 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 53.7.6.   Complete test report issued on the basis of the OECD standard Code for the official testing of front mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 6 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 53.7.7   Complete test report issued on the basis of the OECD standard Code for the official testing of rear mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors, OECD Code 7 with seat-belt anchorages tested, Edition 2015 of July 2014, is provided with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 54.   SAFETY BELTS 54.1.   Requirements under standard ISO 3776-3:2009 (Tractors and machinery for agriculture — Seat belts — Part 3: Requirements for assemblies) are met with relevant documentation included in the information document: yes/no ( 4 ) 54.2.   Test report granted a on the basis of UNECE Regulation No 16 ( OJ L 233, 9.9.2011, p. 1 ) with relevant documentation included in the information document: yes/no ( 4 ) 54.3.    Number and position of safety belts and seats on which they can be used, please fill out table below: Safety belt configuration and associated information       Complete EU type-approval mark Variant, if applicable Belt adjustment device for height (indicate yes/no/optional) Driver's seat   L       C       R       Passenger seat 1   L       C       R       Passenger seat …   L       C       R       L = left, C= centre, R=right 54.4.   Brief description of electrical/electronic components: … 55.   PROTECTION AGAINST PENETRATING OBJECTS (OPS) 55.1.    T- and C-category vehicles equipped for forestry applications 55.1.1.   Requirements under ISO 8084:2003 (Machinery for forestry — Operator protective structures — Laboratory tests and performance requirements) are met with relevant documentation included in the information document: yes/no ( 4 ) 55.2.    All other T- and C-category vehicles fitted with OPS 55.2.1.   Requirements under Annex 14 to UNECE Regulation 43 ( OJ L 230, 31.8.2010, p. 119 ) on safety glazing are met with the relevant documentation included in the information document: yes/no ( 4 ) 56.   OPERATOR'S MANUAL, INFORMATION WARNINGS AND MARKINGS 56.1.    Operator's manual 56.1.1.   Requirements under ISO 3600:1996 (Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Operator's manuals — Content and presentation), with the exception of section 4.3 (Machine identification), are met: yes/no ( 4 ) 56.1.2.   Information requested under Annex XXII to Commission Delegated Regulation (EU) No 1322/2014 is provided in the operator's manual: yes/no ( 4 ) 56.2.    Information, warnings and markings 56.2.1.   Requirements under ISO 3767 Parts 1 (1998+A2:2012) (Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 1: Common symbols) and, if applicable, Part 2 (:2008) (Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 2: Symbols for agricultural tractors and machinery) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 56.2.2.   Alternatively to entry 56.2.1, requirements under UNECE Regulation No 60 ( OJ L 95, 31.3.2004, p. 10 ) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 56.2.3.   Requirements under ISO 11684:1995 (Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Safety signs and hazard pictorials — General principles) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 56.2.4.   Requirements under ISO 7010:2011 (Graphical symbols — Safety colours and safety signs — Registered safety signs) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 56.3.   Description, colour coding and means for the identification of flow directions of hydraulic couplings (including drawings, sketches or photos): … 56.4.   Description, colour coding and means of identification of safe jacking points (including drawings, sketches or photos): … 57.   DRIVER-OPERATED CONTROL DEVICES INCLUDING IDENTIFICATION OF CONTROL DEVICES, TELL-TALES AND INDICATORS 57.1.   Photographs and/or drawings of the arrangement of symbols and controls, tell-tales and indicators: … 57.2.    Controls, tell-tales and indicators for which, when fitted, identification is mandatory, and symbols to be used for that purpose Symbol No Device Control/indicator available  ( *10 ) Identified by symbol  ( *10 ) Where  ( *11 ) Tell-tale available  ( *10 ) Identified by symbol  ( *10 ) Where  ( *11 ) 1 Dipped-beam head lamps             2 Main-beam head lamps             3 Position (side) lamps             4 Front fog lamps             5 Rear fog lamp             6 Headlamp levelling device             7 Parking lamps             8 Direction indicators             9 Hazard warning             10 Windscreen wiper             11 Windscreen washer             12 Windscreen wiper and washer             13 Headlamp cleaning device             14 Windscreen demisting and defrosting             15 Rear window demisting and defrosting             16 Ventilating fan             17 Diesel pre-heat             18 Choke             19 Brake failure             20 Fuel level             21 Battery charging condition             22 Engine coolant temperature             23 Malfunction indicator light (MI)             57.3.    Controls, tell-tales and indicators for which, when fitted, identification is optional, and symbols which shall be used if they are to be identified Symbol No Device Control/indicator available  ( *12 ) Identified by symbol  ( *12 ) Where  ( *13 ) Tell-tale available  ( *12 ) Identified by symbol  ( *12 ) Where  ( *13 ) 1 Parking brake             2 Rear window wiper             3 Rear window washer             4 Rear window wiper and washer             5 Intermittent windscreen wiper             6 Audible warning device             7 Hood             8 Seat belt             9 Engine oil pressure             10 Unleaded petrol             11 …             12 …             57.4.   Brief description and schematic drawing of the locations, displacement, methods of operation and colour coding of the various control devices in the interior of the vehicle and showing for tractors without enclosed cab, how the accessibility to internal control devices from the ground has been avoided: … 57.5.   Brief description and schematic drawing of the locations, displacement, methods of operation and colour coding of the various control devices in the exterior of the vehicle and indicating the front and the rear hazard zones in accordance with Appendix 1 to Annex XXIII to Commission Delegated Regulation (EU) No 1322/2014: … 57.5.   Requirements under Annexes A and C to standard ISO 15077:2008 (Tractors and self-propelled machinery for agriculture — Operator controls — Actuating forces, displacement, location and method of operation) are met with relevant documentation included in the information document: yes/no ( 4 ) 57.6.   Requirements under paragraph 4.5.3 of standard ISO 4254-1:2013 (Agricultural machinery — Safety — Part 1: General requirements), with the exception of fingertip operation control devices, are met with relevant documentation included in the information document: yes/no ( 4 ) 57.7.   Requirements under standard EN 15997:2011 (All terrain vehicles (ATVs — Quads). Safety requirements and test methods) on throttle control and manual clutch control are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 57.8.   For vehicles of T- and C-category, requirements under standard ISO 10975:2009 (Tractors and machinery for agriculture — Auto-guidance systems for operator-controlled tractors and self-propelled machines — Safety requirements) are met with relevant documentation included in the information document: yes/no/not applicable ( 4 ) 58.   PROTECTION AGAINST HAZARDOUS SUBSTANCES 58.1.   Brief description (including drawings and photographs) of the air delivery and filtration system, including the devices to obtain a positive differential within the cab and the air flow of fresh filtered air: … 58.2.   Requirements under standard EN 15695-1 (Agricultural tractors and self-propelled sprayers — Protection of the operator (driver) against hazardous substances — Part 1: Cab classification, requirements and test procedures): category 1/category 2/category 3 category 4 ( 4 ) on cab classification with regard to protection against hazardous substances are met with relevant documentation included in the information document: yes/no ( 4 ) 58.3.   Requirements under standard EN 15695-2 (Agricultural tractors and self-propelled sprayers — Protection of the operator (driver) against hazardous substances — Part 2: Filters, requirements and test procedures): Dust filter/Aerosol filter/Vapour filter ( 4 ) on filters with regard to protection against hazardous substances are met with relevant documentation included in the information document: yes/no ( 4 ) 59.   FOR T- AND C-CATEGORY VEHICLES, MACHINERY ( 63 ) MOUNTED ON THE VEHICLE 59.1.   General description of the machinery and its inter-action with the vehicle: … 59.2.   Overall drawing of the machinery and drawings of the control circuits, as well as the pertinent descriptions and explanations necessary for understanding the operation of the machinery: … ( 1 )   Commission Delegated Regulation (EU) 2015/208 of 8 December 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle functional safety requirements for the approval of agricultural and forestry vehicles ( OJ L 42, 17.2.2015, p. 1 ). ( 2 )   Commission Delegated Regulation (EU) No 1322/2014 of 19 September 2014 supplementing and amending Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle construction and general requirements for the approval of agricultural and forestry vehicles ( OJ L 364, 18.12.2014, p. 1 ). ( 3 )   Commission Delegated Regulation (EU) 2015/96 of 1 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council as regards environmental and propulsion unit performance requirements of agricultural and forestry vehicles ( OJ L 16, 23.1.2015, p. 1 ). ( 4 )   Commission Delegated Regulation (EU) 2015/68 of 15 October 2014 supplementing Regulation (EU) No 167/2013 of the European Parliament and of the Council with regard to vehicle braking requirements for the approval of agricultural and forestry vehicles ( OJ L 17, 23.1.2015, p. 1 ). ( *1 )   Contracting parties to the revised 1958 Agreement. ( *2 )   To be indicated if not obtainable from the type-approval number. ( *3 )   The approval authority shall complete the references for the test reports, established by regulatory acts, for which no type-approval certificate is available. ( *4 )   According to the tyre specification. ( *5 )   Load transmitted to the reference centre of the coupling under static conditions, irrespective to the coupling device; if the maximum permissible vertical load on the coupling point depending on the coupling is indicated in this table, expand the table at the right side and indicate the identification of the coupling device in the header of the column; for R- or S-category vehicles this column(s) concerns the rear coupling devices if there is such a device. ( *6 )   As recommended by the manufacturer. ( *7 )   According to the track roller specification. ( *8 )   Load transmitted to the reference centre of the coupling under static conditions, irrespective to the coupling device; if the maximum permissible vertical load on the coupling point depending on the coupling is indicated in this table, expand the table at the right side and indicate the identification of the coupling device in the header of the column. ( *9 )   Continuously variable transmission. ( 5 )   Commission Delegated Regulation (EU) No 3/2014 of 24 October 2013 supplementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to vehicle functional safety requirements for the approval of two- or three-wheel vehicles and quadricycles ( OJ L 7, 10.1.2014, p. 1 ). ( *10 )    x = yes - = no or not separately available o = optional. ( *11 )    d = directly on control, indicator or tell-tale c = in close vicinity. ( *12 )    x = yes - = no or not separately available o = optional. ( *13 )    d = directly on control, indicator or tell-tale c = in close vicinity.