My bookmarksSign up free
Source

2011/14/EU: Commission Decision of 13 January 2011 amending Decision 97/556/EC on the procedure for attesting the conformity of construction products pursuant to Article 20(2) of Council Directive 89/106/EEC as regards external thermal insulation composite systems/kits with rendering (ETICS) (notified under document C(2011) 34) Text with EEA relevance

2011/14/EU: Commission Decision of 13 January 2011 amending Decision 97/556/EC on the procedure for attesting the conformity of construction products pursuant to Article 20(2) of Council Directive 89/106/EEC as regards external thermal insulation composite systems/kits with rendering (ETICS) (notified under document C(2011) 34) Text with EEA relevance

Decision 97/556/EC · Decision · 3 articles

Data as of 2026-07-04 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗

Article 1

Open ↗

Decision 97/556/EC is amended as follows: 1. Article 2 is replaced by the following: ‘Article 2 The procedure for attesting conformity as set out in Annex II shall be indicated in mandates for guidelines for European technical approvals. The procedure for attesting conformity as set out in Annex III shall be indicated in mandates for harmonised European standards.’; 2. a new Annex III is added, as set out in the Annex to this Decision.

Supplementary provisions

ANNEXSupplementary provisions

Open ↗

ANNEX ‘ANNEX III PRODUCT FAMILY EXTERNAL THERMAL INSULATION COMPOSITE SYSTEMS/KITS WITH RENDERING (1/1) Systems of attestation of conformity For the product(s) and intended use(s) listed below, CEN is requested to specify the following system of attestation of conformity in the relevant harmonised European standards: Product(s) Intended use(s) Level(s) or class(es) (Reaction to fire) Attestation of conformity system(s) External thermal insulation composite systems/kits with rendering (ETICS) In external walls Any 1 System 1: see point (i) of Section 2 of Annex III to Directive 89/106/EEC, without audit testing of samples. The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic [ see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents ]. In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.’

Other acts of the same type
Council Decision (CFSP) 2019/1108 of 27 June 2019 amending Decision 2014/512/CFSP concerning restrictive measures in view of Russia's actions destabilising the situation in UkraineCommission Implementing Decision (EU) 2019/1109 of 27 June 2019 terminating the proceeding concerning imports of welded tubes, pipes and hollow profiles of square or rectangular cross-section, of iron other than cast iron or steel other than stainless, originating in the Republic of North Macedonia, Russia and TurkeyCouncil Decision (CFSP) 2019/1092 of 26 June 2019 amending Decision (CFSP) 2017/2302 in support of the OPCW activities to assist clean-up operations at the former chemical weapons storage site in Libya in the framework of the implementation of the EU Strategy against Proliferation of Weapons of Mass DestructionCouncil Decision (EU) 2019/1093 of 26 June 2019 on the financial contributions to be paid by Member States to finance the European Development Fund, including the second instalment for 2019 and a revised ceiling for the annual amount for 2020Council Decision (EU) 2019/1096 of 25 June 2019 on the signing, on behalf of the Union, of the Investment Protection Agreement between the European Union and its Member States, of the one part, and the Socialist Republic of Viet Nam, of the other partCouncil Decision (EU) 2019/1121 of 25 June 2019 on the signing, on behalf of the European Union, of the Free Trade Agreement between the European Union and the Socialist Republic of Viet NamCouncil Decision (EU) 2019/1133 of 25 June 2019 on the position to be taken on behalf of the European Union in the International Partnership for Energy Efficiency Cooperation (IPEEC) with regard to the extension of the Terms of Reference for the IPEEC for the period from 24 May until 31 December 2019Council Decision (EU) 2019/1319 of 25 June 2019 on the position to be taken on behalf of the European Union within the EPA Committee established under the Interim Agreement establishing a framework for an Economic Partnership Agreement between the Eastern and Southern Africa States, on the one part, and the European Community and its Member States, on the other part, as regards the amendment of certain provisions of Protocol 1 concerning the definition of the concept of ‘originating products’ and methods of administrative cooperationCouncil Decision (EU) 2019/1332 of 25 June 2019 on the signing, on behalf of the Union, and provisional application of the Sustainable Fisheries Partnership Agreement between the European Union and the Republic of The Gambia and of the Protocol on the implementation of that Partnership AgreementCommission Implementing Decision (EU) 2019/1117 of 24 June 2019 amending Decisions 2007/305/EC, 2007/306/EC and 2007/307/EC as regards a change of the addressee of the Decisions (notified under document C(2019) 4523)Commission Decision (EU) 2019/2120 of 24 June 2019 on State aid granted by Belgium to JCDecaux Belgium Publicité (SA.33078 (2015/C) (ex 2015/NN)) (notified under document C(2019) 4466) (Only the French and Dutch versions are authentic) (Text with EEA relevance)Commission Implementing Decision (EU) 2019/1030 of 21 June 2019 postponing the expiry date of approval of indoxacarb for use in biocidal products of product-type 18 (Text with EEA relevance.)

Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.

Contents

What to look at next