My bookmarksSign up free
Source

Commission Implementing Regulation (EU) 2016/323 of 24 February 2016 laying down detailed rules on cooperation and exchange of information between Member States regarding goods under excise duty suspension pursuant to Council Regulation (EU) No 389/2012

Commission Implementing Regulation (EU) 2016/323 of 24 February 2016 laying down detailed rules on cooperation and exchange of information between Member States regarding goods under excise duty suspension pursuant to Council Regulation (EU) No 389/2012

Implementing Regulation (EU) 2016/323 · Regulation · 21 articles

In forceLast amended 2026-02-12

Version history

  1. Superseded version
  2. In force

Data as of 2026-11-02 · Compiled from an official source version. Later amendments or repeals may not be reflected; the official text prevails. · Read the official text ↗

CHAPTER I — GENERAL PROVISIONS

Subject matter

Article 1

Open ↗

For the purposes of cooperation and exchange of information between Member States regarding the movements of excise goods as referred to in Chapter IV and Chapter V, Section 2, of Council Directive (EU) 2020/262 ( 1 ) this Regulation lays down detailed rules concerning the following: (a)  the structure and content of the mutual administrative assistance documents exchanged through the computerised system referred to in Article 2 (8) of Regulation (EU) No 389/2012 for the purposes of Articles 8, 15 and 16 of that Regulation; (b)  the structure and content of communications of feedback on follow-up action taken as a result of cooperation on request or of optional communication of information; (c)  the rules and procedures to be used by competent authorities exchanging mutual administrative assistance documents; (d)  the structure and content of fall-back mutual administrative assistance documents and the rules and procedures relating to their use.

Definitions

Article 2

Open ↗

For the purposes of this Regulation, ‘movement’ means a movement of excise goods between two or more Member States as referred to in Chapter IV and Chapter V, Section 2, of Directive (EU) 2020/262.

Structure and content of mutual administrative assistance documents

Article 3

Open ↗

1.   Mutual administrative assistance documents shall be drawn up in accordance with Annex I. 2.   Where codes are required for the completion of certain data fields in the mutual administrative assistance documents in accordance with Annex I to this Regulation, the codes listed in Annex II to this Regulation, Annex II to Commission Implementing Regulation (EU) No 612/2013 ( 2 ) and Annex II to Commission Delegated Regulation (EU) 2022/1636 ( 3 ) shall be used as set out in the tables of Annex I to this Regulation.

CHAPTER II — COOPERATION ON REQUEST
SECTION I — Requests for download of information contained in the computerised system

Request for download of information where the administrative reference code of a movement is known to the requesting authority

Article 4

Open ↗

1.   Where the administrative reference code of the electronic administrative document or the electronic simplified administrative document, under cover of which a movement takes place, assigned in accordance with Article 20(3), third subparagraph, or Article 36(2), third subparagraph, of Directive (EU) 2020/262, is known to the requesting authority, it may make a request for any document referred to in Annex I to Delegated Regulation (EU) 2022/1636 and any other document relating to the movement. For that purpose the requesting authority shall send a ‘Movement download request’ document, as set out in Table 1 of Annex I, to the requested authority in the Member State of dispatch. The request shall state the administrative reference code of the electronic administrative document or the electronic simplified administrative document under cover of which the movement takes place. 2.   Where the administrative reference code is known to the requested authority, it shall respond to requests made in accordance with paragraph 1 using a ‘Movement download answer’ document, as set out in Table 2 of Annex I, indicating the status of the movement. The requested authority shall also send a ‘History of a movement’ document, as set out in Table 3 of Annex I, containing a copy of the electronic administrative document, or the electronic simplified administrative document, under cover of which the movement takes place and of any other documents relating to that movement. 3.   Where the administrative reference code is not known to the requested authority, it shall respond to requests made in accordance with paragraph 1 using a ‘Movement download answer’ document with the ‘Status’ data element set to ‘None.’

Request for download of information where the administrative reference code is unknown to the requesting authority

Article 5

Open ↗

1.    Where the administrative reference code or codes of one or more electronic administrative documents, or electronic simplified administrative documents, for which the requesting authority is searching, are not known, and the requesting authority believes that another Member State is the Member State of dispatch, the requesting authority may request a search to be carried out by the competent authority of that other Member State for a list of electronic administrative documents or electronic simplified administrative documents under cover of which relevant movements take place. For that purpose, the requesting authority shall send a ‘Common request’ document, as set out in Table 4 of Annex I, to the requested authority. The request shall state the relevant search criteria and include any information which supports the selection of those criteria. 2.   The requested authority shall respond to requests made in accordance with paragraph 1 by returning a list of electronic administrative documents, or electronic simplified administrative documents, matching the search criteria selected in accordance with paragraph 1, second subparagraph, identified by their administrative reference codes using the ‘List of e-AD/e-SAD as a result of a general query’ document, as set out in Table 5 of Annex I. 3.   Where no document meets the search criteria selected in accordance with the second subparagraph of paragraph 1, or the number of administrative reference codes meeting the selected search criteria is greater than 99, the requested authority shall send the requesting authority a ‘Refusal of common request’ document, as set out in Table 6 of Annex I.

SECTION II — Requests for information not contained in the computerised system

Requests for information and administrative enquiries

Article 6

Open ↗

1.   Requests for information regarding excise goods as referred to in Chapter IV and Chapter V, Section 2, of Directive (EU) 2020/262 that is not contained in the computerised system shall be made by sending an ‘Administrative cooperation common request’ document, as set out in Table 7 of Annex I to this Regulation. The request type shall be set to ‘Administrative cooperation’. 2.   Each request made in accordance with paragraph 1 may concern one or more economic operators registered in the Member State of the requesting authority in accordance with Article 19(1)(a) of Regulation (EU) No 389/2012. It shall concern no more than one economic operator registered in the Member State of the requested authority. 3.   Having completed any necessary enquiries, the requested authority shall send the results of those enquiries to the requesting authority by means of an ‘Administrative cooperation results’ document, as set out in Table 10 of Annex I.

Request for manual closure

Article 6a

Open ↗

For the purposes of Article 8(1) of Regulation (EU) No 389/2012, when the movement of excise goods as referred to in Chapter IV and Chapter V, Section 2, of Directive (EU) 2020/262 cannot be closed under Articles 24, 25 or 37 of that Directive, the requesting authority may request the competent authority of the Member State of dispatch to close a movement of excise goods as referred to in Chapter IV and Chapter V, Section 2, of that Directive manually. Such a request shall be made by sending a ‘Manual Closure Request’ document set out in Table 15 of Annex I to this Regulation.

CHAPTER II — COOPERATION ON REQUEST
SECTION III — Time limits and refusals

Time limits

Article 7

Open ↗

1.   A requesting authority may remind a requested authority that it has not yet responded to a previous request for cooperation by sending a ‘Reminder message for administrative cooperation’ document, as set out in Table 9 of Annex I. 2.   Where the requested authority does not respond to a request within the time limits provided for in Article 11(1) of Regulation (EU) No 389/2012 it shall send information on the reasons for the failure using an ‘Answer message’ document, as set out in Table 8 of Annex I to this Regulation.

Refusal to cooperate

Article 8

Open ↗

Where the requested authority refuses to handle a request for information, to carry out an administrative enquiry relating to the requested information, or to provide the information requested, it shall notify the requesting authority by means of an ‘Answer message’ document, as set out in Table 8 of Annex I to this Regulation. It shall send such notification as soon as it has taken its decision and in any event within three months of receipt of the request.

CHAPTER III — EXCHANGE OF INFORMATION WITHOUT PRIOR REQUEST

Optional exchange of information

Article 9

Open ↗

1.   In cases other than those referred to in paragraph 2, optional exchange of information provided for in Article 16 of Regulation (EU) No 389/2012 shall be carried out using an ‘Administrative cooperation results’ document, as set out in Table 10 of Annex I to this Regulation. 2.   Where the optional exchange of information concerns the results of a documentary or physical control of goods during a movement, the results shall be sent using a ‘Control report’ document, as set out in Table 11 of Annex I.

Mandatory exchange of information — Administrative cooperation results

Article 10

Open ↗

Where one of the cases referred to in Article 15(1), points (a) to (e), of Regulation (EU) No 389/2012 is detected as a result of a documentary or physical control of goods at the premises of a registered consignee, within the meaning of Article 3(9) of Directive (EU) 2020/262 (‘registered consignee’), of an authorised warehouse keeper within the meaning of Article 3(1) of that Directive (‘authorised warehouse keeper’), of a certified consignor, within the meaning of Article 3(12) of that Directive (‘certified consignor’), or of a certified consignee, within the meaning of Article 3(13) of that Directive (‘certified consignee’), the mandatory transmission of the necessary information shall be carried out using an ‘Administrative cooperation results’ document, as set out in Table 10 of Annex I to this Regulation. The ‘Administrative cooperation results’ document shall be sent to the competent authorities in the Member State concerned within seven days of the control.

Mandatory exchange of information — control report

Article 11

Open ↗

Where one of the cases referred to in points (a) to (e) of Article 15(1) of Regulation (EU) No 389/2012 is detected as a result of a documentary or physical control of goods during a movement, the mandatory transmission of the control report shall be carried out using a ‘Control report’ document, as set out in Table 11 of Annex I to this Regulation. The ‘Control report’ document shall be sent to the competent authorities in the Member States concerned within seven days of the control.

Mandatory exchange of information — definitive interruption of a movement

Article 12

Open ↗

Where a competent authority becomes aware of the definitive interruption of a movement due to one of the cases referred to in points (a) to (e) of Article 15(1) of Regulation (EU) No 389/2012, the mandatory transmission of that information shall be carried out using an ‘Interruption of movement’ document, as set out in Table 13 of Annex I to this Regulation. The ‘Interruption of movement’ document shall be sent to the competent authorities in the Member States concerned within one day of the moment when the competent authority referred to in the first paragraph becomes aware of the definitive interruption.

Mandatory exchange of information — alert or rejection notification

Article 13

Open ↗

Where a competent authority becomes aware that excise goods which are dispatched within the meaning of Chapter IV and Chapter V, Section 2, of Directive (EU) 2020/262 had not been requested, or that the content of the electronic administrative document or the electronic simplified administrative document is incorrect, and the competent authority suspects that this is due to one of cases referred to in Article 15(1), points (a), (b), (c) or (e), of Regulation (EU) No 389/2012, it shall send an ‘Alert or rejection of an e-AD/e-SAD’ document, as set out in Table 14 of Annex I to this Regulation, to the competent authority of the Member State of dispatch. The ‘Alert or Rejection of an e-AD/e-SAD’ document shall be sent to the competent authority of the Member State of dispatch within one day of the moment when the competent authority becomes aware of the facts referred to in the first paragraph.

Mandatory exchange of information — event reports

Article 14

Open ↗

Where a competent authority becomes aware of facts concerning a movement other than those set out in Articles 10, 11, 12 or 13 and the competent authority suspects that they relate to one of the cases in points (a) to (e) of Article 15(1) of Regulation (EU) No 389/2012, the mandatory transmission of the necessary information shall be carried out using an ‘Event report’ document, as set out in Table 12 of Annex I to this Regulation. The ‘Event report’ document shall be sent within seven days of the moment when the competent authority becomes aware of the facts referred to in the first paragraph.

Mandatory exchange of information — manual closure

Article 14a

Open ↗

For the purpose of Article 15(1), point (c), of Regulation (EU) No 389/2012, where a competent authority of the Member State of dispatch has received evidence of the completion of a movement of excise goods within the meaning of Chapter IV and Chapter V, Section 2, of Directive (EU) 2020/262, and the movement cannot be closed under Articles 24, 25 or 37 of that Directive, it shall decide whether to close the movement of excise goods manually. The competent authority of the Member State of dispatch shall notify the competent authorities of the Member State of destination or of the Member State of export of its decision. The notification of a decision to manually close a movement shall be made by means of a ‘Manual Closure Response’ document, set out in Table 16 of Annex I to this Regulation.

CHAPTER IV — COMMON PROVISIONS ON THE EXCHANGE OF INFORMATION

Unavailability of the computerised system and the use of the fall-back mutual administrative assistance document

Article 15

Open ↗

1.   For the purposes of Article 15(4) of Regulation (EU) No 389/2012, Member States may consider the computerised system to be unavailable in the following circumstances: (a)  the computerised system is unavailable due to hardware or telecommunication failures; (b)  network problems occur which are not under the direct control of the Commission or the Member State concerned; (c)  force majeure; (d)  scheduled maintenance notified at least 48 hours before the planned start of the maintenance period. 2.   For the purposes of the second subparagraph of Article 9(1) and Article 15(4) of Regulation (EU) No 389/2012 the fall-back mutual administrative assistance document shall identify the type of mutual administrative assistance document that it is replacing. The requisite information shall be drawn up as set out in the tables of Annex I to this Regulation in the form of data elements, expressed in the same manner as in the mutual administrative assistance document. All data elements and data groups and subgroups to which those data elements belong shall be identified by numbers and letters referred to in columns A and B of the corresponding tables of Annex I. The fall-back mutual administrative assistance document shall be exchanged by any means agreed between the competent authorities concerned. 3.   As soon as the availability of the computerised system is restored, the information exchanged in accordance with paragraph 2 shall be sent using the computerised system in the form of the appropriate mutual administrative assistance documents.

Feedback on follow-up action taken as a result of exchange of information

Article 16

Open ↗

A request for feedback and feedback on follow-up action in accordance with Article 8(5), Article 15(2) or Article 16(2) of Regulation (EU) No 389/2012 shall be made by means of an ‘Administrative cooperation results’ document, as set out in Table 10 of Annex I to this Regulation. The feedback shall be provided by sending a further ‘Administrative cooperation results’ document, as set out in Table 10.

CHAPTER V — FINAL PROVISIONS

Entry into force

Article 17

Open ↗

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union .

Supplementary provisions

STRUCTURE OF COMMON MESSAGES

ANNEX ISupplementary provisions

Open ↗

ANNEX I STRUCTURE OF COMMON MESSAGES Electronic messages used for the purpose of information exchange concerning excise goods as referred to in the meaning of Chapter IV, and Section 2 of Chapter V, of Directive (EU) 2020/262 EXPLANATORY NOTES (1)  The data elements of the electronic messages used for the purpose of information exchange concerning excise goods within the meaning of Chapter IV and Section 2 of Chapter V, of Directive (EU) 2020/262 using the computerised system referred to in Article 1 of Decision (EU) 2020/263 and in Article 2, point (17), of Regulation (EU) No 389/2012 are structured in data groups and, where applicable, data subgroups. Details regarding the data and their use are presented in the tables of this Annex, in which: (a)  column A sets out the numeric code (number) attributed to each data group and data subgroup; each subgroup follows the sequence number of the data (sub)group of which it forms part (for example: where the data group number is 1, one data subgroup of that group is 1.1 and one data subgroup of that subgroup is 1.1.1); (b)  column B sets out the alphabetic code (letter) attributed to each data element in a data (sub)group; (c)  column C identifies the data (sub)group or data element; (d)  column D indicates for each data (sub)group or data element a value indicating whether the insertion of the corresponding data is: —  ‘R’ (required), meaning that the data must be provided; when a data (sub)group is ‘O’ (optional) or ‘C’ (conditional), data elements within that (sub)group can still be ‘R’ (required) when the competent authorities of the Member State have decided that the data in that (sub)group must be completed or when the condition for the enclosing data (sub)group is fulfilled, —  ‘O’ (optional), meaning that the insertion of the data is optional for the person submitting the message (the consignor or consignee) except where a Member State has stipulated that the data are required in accordance with the option provided for in column E for some of the optional data (sub)groups or data elements, —  ‘C’ (conditional), meaning that the use of the data (sub)group or data element depends on other data (sub)groups or data elements in the same message; (e)  column E sets out the condition(s) on which the insertion of data is conditional, specifies the use of the optional data where applicable and indicates which data must be provided by the competent authorities; (f)  column F provides explanations, where necessary, concerning the completion of the message; (g)  column G indicates: —  for some data (sub)groups a number followed by the character ‘x’ indicating how many times the data (sub)group can be repeated in the message (default = 1), —  for each data element, except for data elements indicating the time or date, the characteristics identifying the data type and the data length; the codes for the data types are as follows: a alphabetic, n numeric, an alphanumeric. The number following the code indicates the admissible data length for the data element concerned. The two dots before the length indicator mean that the data have no fixed length, but can have up to a number of digits, as specified by the length indicator. A comma in the data length means that the data can hold decimals, the number before the comma indicating the total length of the attribute, and the number after the comma indicating the maximum number of digits after the decimal point. For data elements indicating the time or date, the mention ‘date’, ‘time’ or ‘dateTime’ means that the date, the time or the date and time must be given using the ISO 8601 standard for representation of dates and time. (2)  The following abbreviations are used in the tables of this Annex: —  e-AD: electronic administrative document, —  e-SAD: electronic simplified administrative document, —  ARC: administrative reference code, —  SEED: system for exchange of excise data (the electronic database referred to in Article 19(1) of Regulation (EU) No 389/2012), —  CN Code: Combined Nomenclature code, —  LNG: language, —  VAT: value added tax, —  ACO: administrative cooperation, —  EORI: economic operators’ registration and identification. Table 1 (referred to in Article 4) Movement Download Request A B C D E F G 1 ATTRIBUTES R         a Request Correlation Identifier R   The value of <Request Correlation Identifier> is unique per Member State. an..44 2 EXCISE MOVEMENT e-AD/e-SAD R         a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   The value of the Field must be greater than zero. n..2   c Status R   The possible values are: — X01 = Accepted — X02 = Cancelled — X03 = Delivered — X04 = Diverted — X05 = Rejected — X06 = Replaced — X07 = e-AD/e-SAD Manually Closed — X08 = Refused — X09 = None — X10 = Partially Refused — X11 = Exporting — X12 = (reserved) — X13 = Stopped — X14 = Accepted Export Declaration — X15 = e-AD Request Accepted for Export an3   d Last Received Message Type R   The possible values are: — IE801 = E-AD/E-SAD — IE803 = NOTIFICATION OF DIVERTED E-AD/E-SAD — IE807 = INTERRUPTION OF MOVEMENT — IE810 = CANCELLATION OF AN E-AD — IE813 = CHANGE OF DESTINATION — IE818 = ACCEPTED OR (PARTIALLY) REFUSED REPORT OF RECEIPT/EXPORT — IE819 = ALERT OR REJECTION OF AN E-AD/E-SAD — IE829 = NOTIFICATION OF ACCEPTED EXPORT — IE836 = EXPORT DECLARATION INVALIDATION NOTIFICATION TO MSA OF DISPATCH/CONSIGNOR — IE839 = CUSTOMS REJECTION OF E-AD — IE881 = MANUAL CLOSURE RESPONSE — IE905 = STATUS RESPONSE — None = NONE Note:    The IE905 should be included only for historical movements, which were manually closed with an IE905 message. an..5   e Status Request Message Type O   The possible values are: — 1 = Status Synchronisation Request — 2 = Movement History Request n1   f National Movement Information Requested flag R   The format of Boolean is digital: ‘0’ or ‘1’ (‘0’ = No or False; ‘1’ = Yes or True) n1 Table 2 (referred to in Article 4) Movement Download Answer A B C D E F G 1 ATTRIBUTES R         a Request Correlation Identifier R   The value of <Request Correlation Identifier> is unique per Member State. an..44 2 EXCISE MOVEMENT e-AD/e-SAD R         a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   The value of the Field must be greater than zero. n..2   c Status R   The possible values are: — X01 = Accepted — X02 = Cancelled — X03 = Delivered — X04 = Diverted — X05 = Rejected — X06 = Replaced — X07 = e-AD/e-SAD Manually closed — X08 = Refused — X09 = None — X10 = Partially Refused — X11 = Exporting — X12 = (reserved) — X13 = Stopped — X14 = Accepted Export Declaration — X15 = e-AD Request Accepted for Export an3   d Last Received Message Type R   The possible values are: — IE801 = E-AD/E-SAD — IE803 = NOTIFICATION OF DIVERTED E-AD/E-SAD — IE807 = INTERRUPTION OF MOVEMENT — IE810 = CANCELLATION OF AN E-AD — IE813 = CHANGE OF DESTINATION — IE818 = ACCEPTED OR (PARTIALLY) REFUSED REPORT OF RECEIPT/EXPORT — IE819 = ALERT OR REJECTION OF AN E-AD/E-SAD — IE829 = NOTIFICATION OF ACCEPTED EXPORT — IE836 = EXPORT DECLARATION INVALIDATION NOTIFICATION TO MSA OF DISPATCH/CONSIGNOR — IE839 = CUSTOMS REJECTION OF E-AD — IE881 = MANUAL CLOSURE RESPONSE — IE905 = STATUS RESPONSE — None = NONE Note:    The IE905 should be included only for historical movements, which were manually closed with an IE905 message. an..5 Table 3 (referred to in Article 4) History of a movement A B C D E F G 1 ATTRIBUTES R         a Request Correlation Identifier R   The value of <Request Correlation Identifier> is unique per Member State an..44 2 All validated e-ADs/e-SADs R   The set of all draft electronic (simplified) administrative documents or electronic (simplified) administrative documents relating to the movement, the structure of which is set out in Table 1 of Annex I to Delegated Regulation (EU) 2022/1636 99x 3 All Reports of Receipt/Export O   The set of all Report of receipt/Report of export messages relating to the movement, the structure of which is set out in Table 6 of Annex I to Delegated Regulation (EU) 2022/1636 99x 4 Last Notification of Diverted e-AD/e-SAD O   The content of the last Notification of change of destination/Notification of splitting message relating to the movement, the structure of which is set out in Table 4 of Annex I to Delegated Regulation (EU) 2022/1636 1x 5 All Control Reports O   The set of all Control Report messages relating to the movement, the structure of which is set out in Table 11 99x 6 All Event Reports O   The set of all Event Report messages relating to the movement, the structure of which is set out in Table 12 99x 7 All explanations of delay for delivery O   The set of all Explanation on delay for delivery messages relating to the movement 99x 7.1 ATTRIBUTES R         a Message Role R   The possible values are: — 1 = Explanation on delay for sending the report of receipt/export — 2 = Explanation on delay for giving destination n1   b Date and Time of Validation of Explanation on Delay C — ‘R’ after successful validation — Does not apply otherwise   dateTime   c Submitter Type R   The possible values are: — 1 = Consignor — 2 = Consignee n1   d Submitter Identification R   The <Submitter Identification> is a valid trader excise number. (see Code list 1 in Annex II to Regulation (EU) No 612/2013) an13   e Explanation Code R   (see Code list 7 in Annex II) n..2   f Complementary Information C — ‘R’ if <Explanation Code> is ‘Other’ — ‘O’ Otherwise (see Explanation Code in box 7.1e)   an..350   g Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field a2 7.2 EXCISE MOVEMENT R         a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   The value of the Field must be greater than zero. n..2 8 All Notifications of Accepted Export O   The set of all messages ‘Notification of Accepted Export’ relating to the movement, the structure of which is set out in Table 7 of Annex I to Commission Delegated Regulation (EU) 2022/1636 99x 9 All Notifications of invalidation by Customs O   The set of all messages ‘Export declaration invalidation notification to MSA of Dispatch/Consignor’ relating to the movement, the structure of which is set out in Table 9 of Annex I to Commission Delegated Regulation (EU) 2022/1636 99x 10 All Notifications of rejection by Customs O   The set of all messages ‘Customs rejection of electronic administrative document’ relating to the movement, the structure of which is set out in Table 8 of Annex I to Commission Delegated Regulation (EU) 2022/1636 99x 11 The Possible Interruption of Movement O   The content of a possible ‘Interruption of movement’ message relating to the movement, the structure of which is set out in Table 13 1x 12 The Possible Cancellation of an e-AD O   The content of a possible ‘Cancellation of the electronic administrative document’ message relating to the movement, the structure of which is set out in Table 2 of Annex I to Delegated Regulation (EU) 2022/1636 1x 13 All Changes of Destination O   The set of all messages ‘Change of destination’ relating to the movement, the structure of which is set out in Table 3 of Annex I to Delegated Regulation (EU) 2022/1636 99x 14 All Alerts or Rejections of an e-AD/e-SAD O   The set of all ‘Alert or Rejection of an e-AD/e-SAD’ messages relating to the movement, the structure of which is set out in Table 14 99x 15 All Explanations on reason for shortage O     99x 15.1 ATTRIBUTES R         a Submitter Type R   The possible values are: — 1 = Consignor — 2 = Consignee n1   b Date and Time of Validation of Explanation on Shortage C — ‘R’ after successful validation — Does not apply otherwise   dateTime 15.2 EXCISE MOVEMENT R         a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   The value of the Field must be greater than zero. n..2 15.3 TRADER Consignor C — ‘R’ if <Submitter Type> is "Consignor" — Does not apply otherwise (see Submitter Type in box 15.1a)       a Trader Excise Number R   For TRADER Consignor An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION> The <Operator Type Code> of the referred <TRADER> must be: — "Authorised warehouse keeper"; OR — "Registered consignor"; OR — ‘Certified consignor; OR An existing identifier <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>. The <Operator Type Code> of the referred <TRADER> must be ‘Temporary certified consignor’. For TRADER Place of dispatch An existing identifier <Tax Warehouse Reference> (Excise Number in SEED). (see Code list 1 in Annex II to Regulation (EU) No 612/2013) an13   b Trader Name R     an..182   c Street Name R     an..65   d Street Number O     an..11   e Postcode R     an..10   f City R     an..50   g NAD_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field a2 15.4 TRADER Consignee C — ‘R’ if <Submitter Type> is not "Consignor" — Does not apply otherwise (see Submitter Type in box 15.1a)       a Trader Identification C — ‘R’ if <Destination Type Code> is: —  — "Destination – Tax warehouse" — "Destination – Registered consignee" — "Destination – Temporary registered consignee" — "Destination – Direct delivery" — ‘Destination – Certified consignee’ — Destination – Temporary certified consignee’ — "Destination – Return to the place of dispatch of the consignor, for a Duty Paid B2B movement" — ‘O’ if <Destination Type Code> is ‘Destination – Export’ — Does not apply otherwise The possible values of <Trader Identification> are described in the following table: an..16 Destination Type Code TRADER CONSIGNEE. Trader Identification 1 –  Destination – Tax warehouse Excise number (1) 2 –  Destination – Registered consignee Excise number (2) 3 –  Destination – Temporary registered consignee Temporary authorisation reference (4) 4 –  Destination – Direct delivery Excise number (3) 5 –  Destination – Exempted consignee (Does not apply) 6 –  Destination – Export VAT number (optional) 8 –  Destination –Unknown destination (consignee unknown) (Does not apply) 9 –  Destination – Certified consignee Excise number (5) 10 –  Destination – Temporary certified consignee Temporary authorisation reference (6) 11 –  Destination-Return to the place of dispatch of the consignor, for a Duty Paid B2B movement Excise Number (7) or Temporary Authorisation Reference (8) (1)  The operator type of the consignee is "Authorised warehouse keeper". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (2)  The operator type of the consignee is "Registered consignee". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (3)  The operator type of the consignee is either "Authorised warehouse keeper" or "Registered consignee". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (4)  The operator type of the consignee is "Temporary registered consignee". An existing <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>; (5)  The operator type of the consignee is "Certified consignee". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (6)  The operator type of the consignee is "Temporary certified consignee". An existing <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>; (7)  The operator type of the consignee is ‘Certified consignor’. An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (8)  An existing <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION> with Operator Type Code ‘Temporary Certified Consignor’. (see Code list 1 and Code list 2 in Annex II to Regulation (EU) No 612/2013, if applicable)   b EORI Number   — ‘O’ if <Destination Type Code> is ‘Destination – Export’ — Does not apply otherwise Provide the EORI number of the person responsible for lodging the export declaration as set out in Article 21(1) of Council Directive (EU) 2020/262 an..17   c Trader Name R     an..182   d Street Name R     an..65   e Street Number O     an..11   f Postcode R     an..10   g City R     an..50   h NAD_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field a2 15.5 ANALYSIS C At least one of the <ANALYSIS> or <ANALYSIS Body> fields must be present       a Date of Analysis R     date   b Global Explanation R     an..350   c Global Explanation_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field a2 15.6 ANALYSIS Body C At least one of the <ANALYSIS> or <ANALYSIS Body> fields must be present   999x   a Body Record Unique Reference R   The value of the Field must be greater than zero. The <Body Record Unique Reference> must be unique within the message and must refer to a <Body Record Unique Reference> of the e-AD/e-SAD Body of the associated e-AD/e-SAD for which shortages or excesses have been declared. n..3   b Excise Product Code R   (see Code list 10 in Annex II to Delegated Regulation (EU) 2022/1636) an4   c Explanation O     an..350   d Explanation_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field a2   e Actual Quantity O   The value of the Field must be greater than zero. n..15,3 16 All reminder messages for Excise movement O     99x 16.1 ATTRIBUTES R         a Message Type R   The possible values are: — 1 = Reminder message at expiry of time to change destination (or split) — 2 = Reminder message at expiry of time to send the report of receipt/export — 3 = Reminder message at expiry of time to give destination information (Article 22 of Directive (EU) 2020/262) n1   b Date and Time of Issuance of Reminder R     dateTime   c Limit date and Time R     dateTime   d Reminder Information O     an..350   e Reminder Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field a2 16.2 EXCISE MOVEMENT R         a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   The value of the Field must be greater than zero. n..2 Table 4 (referred to in Article 5) Common Request A B C D E F G 1 ATTRIBUTES R         a Request Type R   The possible values are: 1 = (reserved) 2 = Request for reference data 3 = (reserved) 4 = (reserved) 5 = Request for re-synchronisation of the register of economic operators 6 = Request for retrieval of a list of e-Ads/e-SADs 7 = Request for SEED statistics 8 = Request for retrieval of a list of e-Ads 9 = Request for retrieval of a list of e-SADs n1   b Request Message Name C — ‘R’ if <Request Type> is ‘2’ — Does not apply otherwise (see Request Type in box 1a) The possible values are: ‘C_COD_DAT’ = Common list of codes ‘C_PAR_DAT’ = Common system parameters ‘ALL’ = For complete structure a..9   c Requesting Office R   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8 2 E-AD/E-SAD LIST REQUEST C — ‘R’ if <Request Type> is ‘6’, ‘8’ or ‘9’ — Does not apply otherwise (see Request Type in box 1a)       a Member State Code R   (see Code list 3 in Annex II to Delegated Regulation (EU) 2022/1636) a2 2.1 RA_PRIMARY CRITERION R     99x   a Primary Criterion Type Code R   The possible values are: 1 = ARC 2 = Brand name of product 3 = Categories of excise products of the movement 4 = (reserved) 5 = (reserved) 6 = (reserved) 7 = (reserved) 8 = City of consignee 9 = City of consignor 10 = City of guarantor 11 = (reserved) 12 = City of place of delivery 13 = City of tax warehouse of dispatch 14 = City of transporter 15 = CN code of product 16 = Date of invoice 17 = Excise number of consignee 18 = Excise number of consignor 19 = Excise number of guarantor 20 = (reserved) 21 = (reserved) 22 = Excise number of the tax warehouse of destination 23 = Excise number of the tax warehouse of dispatch 24 = (reserved) 25 = Excise product code 26 = Journey time 27 = Member State of destination 28 = Member State of dispatch 29 = Name of consignee 30 = Name of consignor 31 = Name of guarantor 32 = (reserved) 33 = Name of place of delivery 34 = Name of tax warehouse of dispatch 35 = Name of transporter 36 = Number of invoice 37 = Postal code of consignee 38 = Postal code of consignor 39 = Postal code of guarantor 40 = (reserved) 41 = Postal code of place of delivery 42 = Postal code of tax warehouse of dispatch 43 = Postal code of transporter 44 = Quantity of goods (in an e-AD/e-SAD body) 45 = Local Reference Number, being a serial number, assigned by the consignor 46 = Type of transport 47 = (reserved) 48 = (reserved) 49 = VAT number of the consignee 50 = (reserved) 51 = VAT number of the transporter 52 = Change of destination (sequence number ≥ 2) n..2 2.1.1 RA_PRIMARY VALUE R     99x   a Value R   If <Primary Criterion Type Code> is ‘46’ (Type of transport), then an existing <Transport Mode Code> in the list of <TRANSPORT MODES> shall be used. an..255 3 STATISTICS REQUEST C — ‘R’ if <Request Type> is ‘7’ — Does not apply otherwise (see Request Type in box 1a)       a Statistic Type R   The possible values are: 1 = Active/Inactive and Deleted economic operators 2 = Pending expirations 3 = Economic operators by type and tax warehouses 4 = Excise activity 5 = Changes to excise authorisations n1 3.1 LIST OF MEMBER STATES Code R     99x   a Member State Code R   (see Code list 3 in Annex II to Delegated Regulation (EU) 2022/1636) a2 4 STATISTICS PERIOD C — ‘R’ if <Request Type> is ‘7’ — Does not apply otherwise (see Request Type in box 1a)       a Year R   The value of the field must be greater than zero. n4   b Semester C For 4 b , c , and d : The three following data fields are optional and exclusive: — <Semester> — <Quarter> — <Month> i.e. If one of these data fields is given then the two other data fields do not apply The possible values are: 1 = First semester 2 = Second semester n1   c Quarter C The possible values are: 1 = First quarter 2 = Second quarter 3 = Third quarter 4 = Fourth quarter n1   d Month C The possible values are: 1 = January 2 = February 3 = March 4 = April 5 = May 6 = June 7 = July 8 = August 9 = September 10 = October 11 = November 12 = December n..2 5 REFERENCE SYNCHRONISATION C — ‘R’ if <Request Type> is ‘2’ or ‘5’ — Does not apply otherwise. (See Request Type box 1a)       a Period from date R — This field must be prior or equal to field 5b. In case that an extraction is requested, the ‘Period from date’ and/or the ‘Period to date’ fields will be used to request occurrences valid in the specified period. On the contrary, in case a retrieval is requested, the ‘Period from date’ and/or the ‘Period to date’ fields will be used to request occurrences modified and published in the specified period. ( See box 5c ) date   b Period to date R — In case that an extraction is requested, the ‘Period from date’ and/or the ‘Period to date’ fields will be used to request occurrences valid in the specified period. On the contrary, in case a retrieval is requested, the ‘Period from date’ and/or the ‘Period to date’ fields will be used to request occurrences modified and published in the specified period. ( See box 5c ) date   c Extraction O — The value of this field shall be: — 0: for retrieval (or missing in order to enable backward compatibility); — 1: for extraction; — 2: for non-invalidated records. n1   d Member State Code O — (see Code list 3 in Annex II to Delegated Regulation (EU) 2022/1636) a2 6 REFERENCE REQUEST C — ‘R’ if <Request Type> is ‘2’ — Does not apply otherwise (see Request Type in box 1a)       a Common Risk Assessment Criteria flag O   The possible values are: 0 = No or False 1 = Yes or True n1 6.1 LIST OF CODES Code O     99x   a Requested List of Code O   The possible values are: 1 = Units of measure 2 = Events types 3 = Evidence types 4 = (reserved) 5 = (reserved) 6 = Language codes 7 = National Administrations 8 = Country codes 9 = Packaging codes 10 = Reasons for unsatisfactory receipt or control report 11 = Reasons for interruption 12 = (reserved) 13 = Transport modes 14 = Transport units 15 = Wine-growing zones 16 = Wine operation codes 17 = Excise product categories 18 = Excise products 19 = CN codes 20 = Correspondences CN code – Excise product 21 = Cancellation reasons 22 = Alert or rejection of e-AD/e-SAD reasons 23 = Delay explanations 24 = (reserved) 25 = Event submitting persons 26 = Refusal reasons 27 = Reasons for delayed result 28 = Request actions 29 = Request reasons 30 = (reserved) 31 = (reserved) 32 = (reserved) 33 = (reserved) 34 = Administrative cooperation action not possible reasons 35 = (reserved) 36 = Type of document 37 = (reserved) 38 = (reserved) 39 = Manual Closure Request Reasons 40 = Manual Closure Rejection Reasons 41 = National Administration – Degree Plato n..2 Table 5 (as referred to in Article 5(2)) List of e-AD/e-SAD as result of a general query A B C D E F G 1 ATTRIBUTES R         a Requesting Office R   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   b Request Correlation Identifier R   The value of <Request Correlation Identifier> is unique per Member State. an..44 2 E-AD/E-SAD LIST ITEM O     99x   a Dispatch Date R     date 2.1 EXCISE MOVEMENT R         a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Date and Time of Validation of e-AD/e-SAD R     dateTime   c Sequence Number R   The value of the field must be greater than zero. n..2 2.2 TRADER Consignor R         a Trader Excise Number R   Provide a valid SEED registration number of the authorised warehousekeeper, registered consignor, certified consignor or temporary certified consignor. (see Code list 1 in Annex II to Regulation (EU) No 612/2013) an13   b Trader Name R     an..182 2.3 TRADER Place of Dispatch C IF <E-AD/E-SAD.Origin Type Code> is ‘Origin – Tax warehouse’ or ‘Origin – Duty Paid’ THEN <TRADER Place of Dispatch> is ‘R’ <OFFICE of Dispatch – Import> does not apply ELSE <TRADER Place of Dispatch> does not apply <OFFICE of Dispatch – Import> is ‘R’       a Tax Warehouse Reference C Doesn’t apply for Origin Type Code in box 9d ‘3’ (See for Origin Type Code box 9d in Table 1 of Delegated Regulation (EU) 2022/1636) For TRADER Place of dispatch An existing identifier <Tax Warehouse Reference> (Excise Number in SEED). (see Code list 1 in Annex II to Regulation (EU) No 612/2013) an13   b Trader Name C ‘R’ if Origin Type Code in box 9d is ‘3’ (See for Origin Type Code box 9d in Table 1 of Delegated Regulation (EU) 2022/1636)   an..182 2.4 OFFICE of Dispatch – Import C IF <E-AD/E-SAD.Origin Type Code> is ‘Origin – Tax warehouse’ or ‘Origin – Duty Paid’ THEN <TRADER Place of Dispatch> is ‘R’ <OFFICE of Dispatch – Import> does not apply ELSE <TRADER Place of Dispatch> does not apply <OFFICE of Dispatch – Import> is ‘R’       a Office Reference Number R   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8 2.5 TRADER Consignee C ‘R’, except –for Destination Type Code 8       a Trader Identification C IF <Destination Type Code> is in: — ‘Destination – Tax warehouse’ — ‘Destination – Registered consignee’ — ‘Destination – Temporary registered consignee’ — ‘Destination – Direct delivery’ — ‘Destination – Certified consignee’ — ‘Destination – Temporary certified consignee’ — ‘Destination – Return to the place of dispatch of the consignor, for a Duty Paid B2B movement’ THEN <TRADER Consignee.Trader Identification> is ‘R’ ELSE IF <Destination Type Code> is: — ‘Destination – Export’ THEN <TRADER Consignee.Trader Identification> is ‘O’ ELSE <TRADER Consignee.Trader Identification> does not apply The possible values of <Trader Identification> are described in the following table: an..16 Destination Type Code TRADER CONSIGNEE. Trader Identification 1 –  Destination – Tax warehouse Excise number (1) 2 –  Destination – Registered consignee Excise number (2) 3 –  Destination – Temporary registered consignee Temporary authorisation reference (4) 4 –  Destination – Direct delivery Excise number (3) 5 –  Destination – Exempted consignee (Does not apply) 6 –  Destination – Export VAT number (optional) 8 –  Destination –Unknown destination (consignee unknown) (Does not apply) 9 –  Destination – Certified consignee Excise number (5) 10 –  Destination – Temporary certified consignee Temporary authorisation reference (6) 11 –  Destination-Return to the place of dispatch of the consignor, for a Duty Paid B2B movement Excise Number (7) or Temporary Authorisation Reference (8) (1)  The operator type of the consignee is ‘Authorised warehouse keeper’. An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (2)  The operator type of the consignee is ‘Registered consignee’. An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (3)  The operator type of the consignee is either ‘Authorised warehouse keeper’ or ‘Registered consignee’. An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (4)  The operator type of the consignee is ‘Temporary registered consignee’. An existing <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>; (5)  The operator type of the consignee is ‘Certified consignee’. An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (6)  The operator type of the consignee is ‘Temporary certified consignee’. An existing <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>; (7)  The operator type of the consignee is "Certified consignor". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (8)  An existing <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION> with Operator Type Code "Temporary Certified Consignor". (see Code list 1 and Code list 2 in Annex II to Regulation (EU) No 612/2013, if applicable)   b Trader Name R     an..182   c EORI Number C — ‘O’ if <Destination Type Code> is ‘Destination – Export’ — Does not apply otherwise Provide the EORI number of the person responsible for lodging the export declaration as set out in Article 21(1) of Council Directive (EU) 2020/262. an..17 2.6 TRADER Place of Delivery C The optionality of field <TRADER Place of Delivery> is described below, according to the <Destination Type Code>: — ‘R’ for Destination Type Code 1, 4, ‘9’ and ‘10’ — ‘O’ for Destination Type Code 2, 3 and 5 — does not apply otherwise. — —   a Trader Identification C IF <Destination Type Code> is ‘Destination – Tax warehouse’ or ‘Destination – Certified consignee’ or ‘Destination – Temporary certified consignee’ THEN <TRADER Place of Delivery. Trader Identification> is ‘R’ ELSE IF <Destination Type Code> is ‘Destination – Direct delivery’ or ‘Destination-Return to the place of dispatch of the Consignor’ THEN <TRADER Place of Delivery. Trader Identification> does not apply ELSE <TRADER Place of Delivery. Trader Identification> is ‘O’ The possible values of <Trader Identification> are described in the following table: an..16 Destination Type Code TRADER Place of Delivery.Trader Identification 1 –  Destination – Tax warehouse Tax Warehouse Reference (Excise Number) (1) 2 –  Destination – Registered consignee Any identification (*) 3 –  Destination – Temporary registered consignee Any identification (*) 4 –  Destination – Direct delivery (Does not apply) 5 –  Destination – Exempted consignee Any identification (*) 6 –  Destination – Export (The field <TRADER Place of Delivery> does not exist) 8 –  Unknown destination (The field <TRADER Place of Delivery> does not exist) 9 –  Destination – Certified consignee Any identification (*) 10 –  Destination – Temporary certified consignee Any identification (*) 11 –  Destination-Return to the place of dispatch of the consignor, for a Duty Paid B2B movement (The field <TRADER Place of Delivery> does not exist) (1)  An existing identifier <Tax Warehouse Reference> in the set of <TAX WAREHOUSE>; (*)  For the place of delivery, "Any identification" means: a VAT number or any other identifier. (see Code list 1 and Code list 2 in Annex II to Regulation (EU) No 612/2013, if applicable)   b Trader Name C IF <Destination Type Code> is ‘Destination – Direct delivery’ THEN <Trader Name> is ‘O’ ELSE <Trader Name> is ‘R’   an..182 2.7 OFFICE Place of Delivery – Customs C The optionality of the field <OFFICE Place of delivery – Customs> is described below, according to <Destination Type Code>: — ‘R’ for Destination Type Code 6 — does not apply otherwise       a Office Reference Number R   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8 2.8 EXCISE PRODUCTS CATEGORY Code R     9x   a Excise Product Category Code R   (see Code list 3 in Annex II to Regulation (EU) No 612/2013) a1 2.9 TRADER Transport Arranger C IF <E-AD/E-SAD Header.Transport Arrangement>(IE801) (or <E-AD/E-SAD Header.Transport Arrangement>(IE815)) is ‘Consignor’ or ‘consignee’ THEN <TRADER Transport Arranger> does not apply ELSE <TRADER Transport Arranger> is ‘R’       a VAT Number O     an..14   b Trader Name R     an..182 2.10 TRADER First Transporter O         a VAT Number O     an..14   b Trader Name R     an..182 Table 6 (referred to in Article 5) Refusal of Common Request A B C D E F G 1 Common Request Message R   The context of the Common Request message relating to the movement, the structure of which is set out in Table 4   2 Rejection R     99x   a Rejection Date and Time R     dateTime   b Rejection Reason Code R   The possible values are: — 0 = Other — 2 = No e-AD(s) /e-SAD(s) retrieved matching selection criteria — 3 = Reference data not available — 4 = Excise Office List not available — 5 = SEED data not available — 7 = Unknown requested data — 8 = Increment number out of range — 26 = Duplicate detected — 112 = Incorrect (code) value — 115 = Not supported in this position n..3 Table 7 (as referred to in Article 6(1)) Administrative Cooperation Common Request A B C D E F G 1 ATTRIBUTES R         a Request Type R   The possible values are: 1 = Administrative cooperation 2 = reserved n1   b Deadline for Results R     date 2 FOLLOW UP R         a Follow-Up Correlation ID R   (see Code list 1 in Annex II) an28   b Date of Issuance R     date   c Sender Member State Code R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   d Sender Office Reference Number O   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   e Sender Officer O     an..35   f Addressee Member State Code R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   g Addressee Office Reference Number O   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   h Addressee Officer O     an..35   i National Case Reference Identifier O     an..99 3 ADMINISTRATIVE COOPERATION REQUEST C — ‘R’ if <Request Type> is ‘1’ — Does not apply otherwise (see Request Type in box 1a)       a Administrative Cooperation Request Information R     an..999   b Administrative Cooperation Request Information_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   c Flag O   This attribute is used in the Administrative Cooperation Common Request to denote whether a special condition applies. The possible values are: 0 = No special condition applies. The request follows the standard Administrative Cooperation process. 1 = A special condition applies. The request requires additional attention. n1 3.1 REQUEST REASON Code R     99x   a Administrative Cooperation Request Reason Code R   (see Code list 8 in Annex II) n..2   b ACO_Complementary Information C — ‘R’ if <Administrative Cooperation Request Reason Code> is ‘Other’ — ‘O’ otherwise — an..999   c ACO_Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 3.1.1 RISK ASSESSMENT REFERENCE O     99x   a Other Risk Profile O     an..999   b Other Risk Profile_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 3.2 ARC List O     99x   a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number O   The value of the Field must be greater than zero. n..2 3.3 TRADER Person O     99x   a Trader Excise Number C For 3.3 a , b , and c : at least one of the following attributes must be present: — <Trader Excise Number> — <VAT Number> — <Trader Name> An existing identifier (Excise Number) <Trader Excise Number> in the set of <TRADER AUTHORISATION> or <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>. (see Code list 1 and Code list 2 in Annex II to Regulation (EU) No 612/2013) an13   b VAT Number C   an..14   c Trader Name C   an..182   d Member State Code C — ‘R’ if <Trader Name> is given and <Trader Excise Number> is not given and <VAT Number> is not given — Does not apply otherwise (see Trader Excise Number in box 3.3a, VAT Number in box 3.3b, Trader Name in box 3.3c) A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   e Street Name O     an..65   f Street Number O     an..11   g Postcode O     an..10   h City O     an..50   i Phone Number O     an..35   j Fax Number O     an..35   k Email Address O     an..70   l NAD_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 3.4 SUPPORTING DOCUMENTS O     9x   a Short Description of Supporting Document C — ‘R’ if <Supporting Document Type> is ‘Other’ — Doesn’t apply otherwise (see Reference of Supporting Document in box 3.4c and Image of Document in box 3.4e)   an..999   b Short Description of Supporting Document_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   c Reference of Supporting Document C At least one, among these three fields, must be present: — <Supporting Document Type> — <Reference of Supporting Document> — <Image of Document> (see Short Description of Supporting Document in box 3.4a and Image of Document in box 3.4e)   an..999   d Reference of Supporting Document_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II, to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   e Image of Document C At least one, among these three fields, must be present: — <Supporting Document Type> — <Reference of Supporting Document> — <Image of Document> (see Short Description of Supporting Document in box 3.4a and Reference of Supporting Document in box 3.4c)       f Supporting Document Type C At least one, among these three fields, must be present: — <Supporting Document Type> — <Reference of Supporting Document> — <Image of Document> See Reference of Supporting Document in box 3.4c and Image of Document in box 3.4e (see code list 15 in Annex II) an..4 3.5 ACTIONS Requested O     99x   a Administrative Cooperation Action Code R   (see Code list 9 in Annex II) n..2   b ACO Action Complement C — ‘R’ if <Administrative Cooperation Action Code> is ‘Other’ — ‘O’ otherwise (see Administrative Cooperation Action Code in box 3.5a)   an..999   c ACO Action Complement_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 4 CONTACT O         a Office Reference Number R   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   b Submitting Excise Officer O     an..35   c Tel. Number O     an..35   d Fax Number O     an..35   e Email Address O     an..70 Table 8 (referred to in Article 7) Answer message A B C D E F G 1 ATTRIBUTES R         a Message Type R   The possible values are: — 1 = Administrative Cooperation answer message — 2 = reserved n1 2 FOLLOW UP R         a Follow Up Correlation ID R   (see Code list 1 in Annex II) an28   b Date of Issuance R     date   c Sender Member State Code R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636 a2   d Sender Office Reference Number O   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   e Sender Officer O     an..35   f Addressee Member State Code R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636 a2   g Addressee Office Reference Number O   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   h Addressee Officer O     an..35   i National Case Reference Identifier C — ‘O’ If <Follow Up Correlation ID> does not match with <Follow Up Correlation ID> in a request message — "R" If <Follow Up Correlation ID> matches with <Follow Up Correlation ID> in a request message AND <National Case Reference Identifier> is present in the request message IF <Follow Up Correlation ID> matches with <Follow Up Correlation ID> in a request message AND <National Case Reference Identifier> is present in the request message THEN <National Case Reference Identifier> must be equal to the value of <National Case Reference Identifier> in the request message. an..99 3 ANSWER R         a Deadline for Results C For 3 a and b: — ‘R’ if < Refusal Reason Code> is provided — Does not apply otherwise (see Refusal Reason Code in box 3c)   dateTime   b Delayed Result Reason Code C (see Code list 3 in Annex II) n..2   c Refusal Reason Code O   (see Code list 4 in Annex II) n..2   d Refusal Reason Complement C — ‘R’ if < Refusal Reason Code> is ‘Other’ — Does not apply otherwise (see Refusal Reason Code in box 3c)   an..999   e Refusal Reason Complement_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field a2 Table 9 (referred to in Article 7) Reminder Message for Administrative Cooperation A B C D E F G 1 ATTRIBUTES R         a Message Type R   The possible values are: — 1 = Administrative cooperation results reminder message — 2 = Reserved n1 2 FOLLOW UP R         a Follow Up Correlation ID R   (see Code list 1 in Annex II) an28   b Date of Issuance R     date   c Sender Member State Code R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636 a2   d Sender Office Reference Number O   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   e Sender Officer O     an..35   f Addressee Member State Code R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636 a2   g Addressee Office Reference Number O   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   h Addressee Officer O     an..35   i National Case Reference Identifier C — ‘O’ If <Follow Up Correlation ID> does not match with <Follow Up Correlation ID> in a request message — "R" If <Follow Up Correlation ID> matches with <Follow Up Correlation ID> in a request message AND — <National Case Reference Identifier> is present in the request message — Otherwise it does not apply. IF <Follow Up Correlation ID> matches with <Follow Up Correlation ID> in a request message AND <National Case Reference Identifier> is present in the request message THEN <National Case Reference Identifier> must be equal to the value of <National Case Reference Identifier> in the request message. an..99 Table 10 (as referred to in Article 6(3), Article 9(1) and Articles 10 and 16) Administrative Cooperation Results A B C D E F G 1 FOLLOW UP R         a Follow Up Correlation ID R   (see Code list 1 in Annex II) an28   b Date of Issuance R     date   c Sender Member State Code R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   d Sender Office Reference Number O   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   e Sender Officer O     an..35   f Addressee Member State Code R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   g Addressee Office Reference Number O   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   h Addressee Officer O     an..35   i National Case Reference Identifier C — ‘O’ If <Follow Up Correlation ID> does not match with <Follow Up Correlation ID> in a request message — ‘R’ If <Follow Up Correlation ID> matches with <Follow Up Correlation ID> in a request message AND — <National Case Reference Identifier> is present in the request message — Otherwise it does not apply. IF <Follow Up Correlation ID> matches with <Follow Up Correlation ID> in a request message AND <National Case Reference Identifier> is present in the request message THEN <National Case Reference Identifier> must be equal to the value of <National Case Reference Identifier> in the request message. an..99 2 CONTACT O         a Office Reference Number R   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   b Submitting Excise Officer O     an..35   c Tel. Number O     an..35   d Fax Number O     an..35   e Email Address O     an..70 3 (ADMINISTRATIVE COOPERATION)ACTION RESULT O     99x   a ARC O   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number C — ‘O’ if <ARC> is present — Does not apply otherwise (see ARC in box 3a) The value of the Field must be greater than zero. n..2   c Administrative Cooperation Action Code R   (see Code list 9 in Annex II) n..2   d ACO Action Complement C — ‘R’ if <Administrative Cooperation Action Code> is ‘Other’ — ‘O’ otherwise (see Administrative Cooperation Action Code in box 3c)   an..999   e ACO Action Complement_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   f ACO Action Not Possible Reason Code O   (see Code list 11 in Annex II) n..2   g ACO Action Not Possible Reason Complement C — ‘R’ if <ACO Action Not Possible Reason Code> is ‘Other’ — ‘O’ otherwise (see ACO Action Not Possible Reason Code in box 3f)   an..999   h ACO Action Not Possible Reason Complement_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   i Finding at Destination O   The possible values are: 0 = Other finding 1 = (reserved) 2 = Consignment in order 3 = Consignment has not reached destination 4 = Consignment arrived late 5 = Shortage detected 6 = Excise products not in order 7 = Consignment not entered in stock records 8 = Trader could not be contacted 9 = Missing trader 10 = Excess detected 11 = Wrong EPC 12 = Wrong destination type code 13 = Differences confirmed 14 = Manual closing recommended 15 = Interruption recommended 16 = Irregularities Found n..2   j Other Finding Type C — ‘R’ if <Finding at Destination> is ‘Other finding’ — Does not apply otherwise (see Finding at Destination in box 3i)   an..999   k Other Finding Type_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   l Complementary Explanations O     an..999   m Complementary Explanations_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   n Control Report Reference O   (see Code list 2 in Annex II) A ‘Control Report’ message exists in the system (including the case that it is encapsulated in a received ‘History of a movement’ message) having the same <Control Report Reference> with that of the submitted message. In addition if the <ARC> is provided in the submitted message then it coincides with the <ARC> of the referenced ‘Control Report’ message. (see ARC in box 3a) an16 4 FEEDBACK REQUEST O         a Feedback Requested or Provided R   The possible values are: 0 = No feedback requested 1 = Feedback requested 2 = Feedback provided n1   b Follow Up Actions C At least one among these two fields if box 4a is given: — <Follow Up Actions> — <Relevance of Information>   an..999   c Follow Up Actions_LNG C — ‘R’ if the corresponding text field(s) is (are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   d Relevance of Information Provided C At least one among these two fields if box 4a is given: — < Follow Up Actions> — <Relevance of Information>   an..999   e Relevance of Information_LNG C — ‘R’ if the corresponding text field(s) is (are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 5 SUPPORTING DOCUMENTS O     9x   a Short Description of Supporting Document C — ‘R’ if <Supporting Document Type> is ‘Other’ — Doesn’t apply otherwise (See Supporting Document Type in box 5f)   an..999   b Short Description of Supporting Document_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   c Reference of Supporting Document C At least one, among these three fields, must be present: — <Short Description of Supporting Document> — <Reference of Supporting Document> — <Image of Document> (see Short Description of Supporting Document in box.5a and Image of Document in box 5e)   an..999   d Reference of Supporting Document_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   e Image of Document C At least one, among these three fields, must be present: — <Short Description of Supporting Document> — <Reference of Supporting Document> — <Image of Document> (see Short Description of Supporting Document in box 5a and Reference of Supporting Document in box 5c)       f Supporting Document Type C At least one, among these three fields, must be present: — <Short Description of Supporting Document> — <Reference of Supporting Document> — <Image of Document> (see Short Description of Supporting Document in box 5a, Reference of Supporting Document in box 5c and Image of Document in box5e) (see code list 15 in Annex II) an..4 Table 11 (as referred to in Article 9(2) and Article 11) Control Report A B C D E F G 1 ATTRIBUTES R         a Message Type R   The possible values are: 1 = Validated document n1   b Date and Time of Validation of Control Report C — ‘R’ after successful validation — Does not apply otherwise   dateTime 2 CONTROL REPORT HEADER R         a Control Report Reference R   (see Code list 2 in Annex II) an16 2.1 CONTROL OFFICE R         a Control Office Reference Number O   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8   b Member State Code C For 2.1 b , c , d , e , f , and g : — ‘R’ except for <Street Number>, which is ‘O’, if <Control Office Reference Number> is not given — Does not apply otherwise (see Control Office Reference Number in box 2.1a) A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   c Control Office Name C   an..35   d Street Name C   an..65   e Street Number C   an..11   f Postcode C   an..10   g City C   an..50   h Phone Number C For 2.1 h, i and j : If <Control Office Reference Number> is not given, at least one of the following three attributes must be present: — <Phone Number> — <Fax Number> — <Email Address> — otherwise, none of the three attributes are applicable (see Control Office Reference Number in box 2.1a)   an..35   i Fax Number C   an..35   j Email Address C   an..70   k NAD_LNG C ‘R’ if the corresponding text field(s) is (are) used Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 3 EXCISE MOVEMENT C One of the <EXCISE MOVEMENT> or <OTHER ACCOMPANYING DOCUMENT> fields must be present       a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   The value of the Field must be greater than zero. n..2 4 OTHER ACCOMPANYING DOCUMENT C One of the <EXCISE MOVEMENT> or <OTHER ACCOMPANYING DOCUMENT> fields must be present       a Other Accompanying Document Type R   The possible values are: 0 = Other 2 = (reserved) n1   b Short Description of Other Accompanying Document C ‘R’ if <Other Accompanying Document Type> is ‘Other’ It doesn’t apply otherwise   an…350   c Short Description of Other Accompanying Document_LNG C — ‘R’ if the corresponding text field(s) is (are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. n2   d Other Accompanying Document Number R     an…350   e Other Accompanying Document Date R     date   f Image of Other Accompanying Document O         g Member State of Dispatch R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   h Member State of Destination R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2 4.1 TRADER Person Involved in Movement O     9x   a Trader Excise Number C At least one of the following attributes must be present: — <Trader Excise Number> — <Trader Identification> — <Trader Name> An existing identifier (Excise Number) <Trader Excise Number> in the set of <TRADER AUTHORISATION> or <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>. (see Code list 1 in Annex II to Regulation (EU) No 612/2013) an13   b Trader Identification C At least one of the following attributes must be present: — <Trader Excise Number> — <Trader Identification> — <Trader Name> A VAT number or any other National number. an16   c Trader Name C At least one of the following attributes must be present: — <Trader Excise Number> — <Trader Identification> — <Trader Name> — an..182   d Trader Person Type O   The possible values are the following: 1 = Consignor 2 = Consignee 3 = Tax representative 4 = Vendor 5 = Liable person 6 = Customer private individual n..2   e Member State Code C ‘R’ if <Trader Name> is given AND <Trader Excise Number> and <Trader Identification> is not given. It doesn’t apply otherwise (see Code list 3 in Annex II to Delegated Regulation (EU) 2022/1636) a2   f Street Name O     an..65   g Street Number O     an..11   h Postcode O     an..10   i City O     an..50   j NAD_LNG C — ‘R’ if the corresponding text field(s) is (are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   k Phone Number O     an..35   l Email Address O     an..70 4.2 GOODS ITEM O     999x   a Description of the Goods O     an..55   b CN Code C — ‘R’ if <OTHER ACCOMPANYING DOCUMENT.Image of Other Accompanying Document> is not present in the <OTHER ACCOMPANYING DOCUMENT> field — Does not apply otherwise (see Data group 4 and box 4f) The value of the Field must be greater than zero. n8   c Commercial Description of the Goods O     an..999   d Additional code O     an..35   e Quantity C — ‘R’ if <OTHER ACCOMPANYING DOCUMENT.Image of Other Accompanying Document> is not present in the <OTHER ACCOMPANYING DOCUMENT> field — Does not apply otherwise (see Data group 4 and box 4f) The value of the Field must be greater than zero. n..15,3   f Unit of Measure Code C — ‘R’ if <OTHER ACCOMPANYING DOCUMENT.Image of Other Accompanying Document> is not present in the <OTHER ACCOMPANYING DOCUMENT> field — Does not apply otherwise (see Data group 4 and box 4f) (See Annex II to Delegated Regulation (EU) 2022/1636, Code list 11) n..2   g Gross Mass O   The Gross Mass must be equal to or higher than Net Mass. The value of the Field must be greater than zero. n..16,6   h Net Mass O   The Gross Mass must be equal to or higher than Net Mass. The value of the Field must be greater than zero. n..16,6 4.3 MEANS OF TRANSPORT C — ‘R’ if <OTHER ACCOMPANYING DOCUMENT.Image of Other Accompanying Document> is not present in the <OTHER ACCOMPANYING DOCUMENT> field — Does not apply otherwise (see Data group 4 and box 4f)       a Trader Name R     an..182   b Street Name R     an..65   c Street Number O     an..11   d Transporter Country R   Provide a ‘Country Code’ listed in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   e Postcode R     an..10   f City R     an..50   g Transport Mode Code R   Provide the mode of transport using the codes in Code list 6 of Annex II to Delegated Regulation (EU) 2022/1636. n..2   h ACO_Complementary Information C — ‘R’ if <MEANS OF TRANSPORT. Transport Mode Code> is ‘Other’ — Does not apply otherwise (see box 4.3 g)   an..999   i ACO_Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is (are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   j Registration R     an..35   k Country of Registration R   Provide a ‘Country Code’ listed in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2 5 CONTROL REPORT R         a Date of Control R     date   b Place of Control R     an..350   c Place of Control_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   d Control Type R   The possible values are: 1 = Physical control 2 = Documentary control n1   e Reason for Control R   The possible values are: 0 = Other reason 1 = Control started at random 2 = Event signalled 3 = Request for assistance received 4 = Request from another office 5 = Alert received n1   f Complementary Origin Reference O     an..350   g Complementary Origin Reference_LNG C — ‘R’ if the corresponding text field is used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   h Control Officer Identity R     an..350   i Control Officer Identity_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   j Global Control Conclusion R   The possible values are: 1 = Satisfactory 2 = Minor discrepancies found 3 = Interruption recommended 4 = Intention to make claim under Article 9 or Article 46 of Council Directive (EU) 2020/262 5 = Allowable loss detected, in relation to Article 6 or Article 45 of Council Directive (EU) 2020/262 n1   k Control at Arrival Required R   The possible values are: 0 = No or False 1 = Yes or True n1   l Flag R   This attribute indicates the outcome of the control. The possible values are: 0 = Control positive, no irregularities detected 1 = Control negative, irregularities detected. n1   m Comments O     an..350   n Comments_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 5.1 PERFORMED CONTROL ACTION R     99x   a Performed Control Action R   The possible values are: 0 = Other control action 1 = Verified counted packs 2 = Unloaded 3 = Opened packs 4 = Annotated paper copy of documents 5 = Counting 6 = Sampling 7 = Administrative control 8 = Goods weighted/measured 9 = Random check 10 = Control of records 11 = Compare documents presented with e-AD/e-SAD n..2   b Other Control Action C — ‘R’ if <Performed Control Action> is ‘0’ — Does not apply otherwise (see Performed Control Action in box 5.1a)   an..350   c Other Control Action_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 5.2 SUPPORTING EVIDENCE C — ‘R’ if <Reason for Control> is ‘2’ — ‘O’ otherwise (see Reason for Control in box 5e)   9x   a Issuing Authority O     an..35   b Issuing Authority_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   c Evidence Type Code R   (see Code list 6 in Annex II) n..2   d Evidence Type Complement C — ‘R’ if <Evidence Type Code> is ‘Other’ — Does not apply otherwise (see Evidence Type Code in box 5.2c)   an..350   e Evidence Type Complement_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   f Reference of Evidence O     an..350   g Reference of Evidence_LNG C — ‘R’ if the corresponding text(s) field is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   h Image of Evidence O       5.3 UNSATISFACTORY REASON O     9x   a Unsatisfactory Reason Code R   (see Code list 12 in Annex II) n..2   b Complementary Information C — ‘R’ if <Unsatisfactory Reason Code> is ‘Other’ — Does not apply otherwise (see Unsatisfactory Reason Code in box 5.3a)   an..350   c Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 5.4 TRANSPORT DETAILS O     99x   a Transport Unit Code R   (see Code list 7 in Annex II to Delegated Regulation (EU) 2022/1636) n..2   b Identity of Transport Units C — ‘R’ if <Transport Unit Code> is not ‘Fixed transport installations’ — Does not apply otherwise (see Transport Unit Code in box 5.4a)   an..35   c Identity of Commercial Seal O     an..35   d Seal Information O     an..350   e Seal Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   f Complementary Information O     an..350   g Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 5.5 CONTROL REPORT Body O     99x   a Body Record Unique Reference C — ‘R’ if <EXCISE MOVEMENT > field is present — Does not apply otherwise This value refers to the <Body Record Unique Reference> of the e-AD/e-SAD Body of the associated e-AD/e-SAD and must be unique within the message. The value of the Field must be greater than zero. n..3   b Description of the Goods C — ‘O’ if the <OTHER ACCOMPANYING DOCUMENT> field is present — Does not apply otherwise — an..55   c CN Code C — ‘R’ if the <OTHER ACCOMPANYING DOCUMENT> field is present — Does not apply otherwise The value of the Field must be greater than zero. n8   d Additional code C — ‘O’ if the <OTHER ACCOMPANYING DOCUMENT> field is present — Does not apply otherwise — an..35   e Indicator of Shortage or Excess O   The possible values are: S = Shortage E = Excess a1   f Observed Shortage or Excess C — ‘R’ if <Indicator of Shortage or Excess> is given — Does not apply otherwise (see Indicator of Shortage or Excess in box 5.5e) The value of the Field must be greater than zero. n..15,3   g Comments O     an..350   h Comments_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 5.5.1 UNSATISFACTORY REASON O     9x   a Unsatisfactory Reason Code R   (see Code list 12 in Annex II) n..2   b Complementary Information C — ‘R’ if <Unsatisfactory Reason Code> is ‘Other’ — ‘O’ otherwise (see Indicator of Unsatisfactory Reason Code in box 5.5.1a)   an..350   c Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 Table 12 (as referred to in Article 14) Event Report A B C D E F G 1 ATTRIBUTES R         a Message Type R   The possible values are: 1 = Initial submission 3 = Validated document n1   b Date and Time of Validation of Event Report C — ‘R’ after successful validation, — Does not apply otherwise   dateTime 2 EVENT REPORT HEADER R         a Event Report Number C — ‘R’ if <Message Type> is ‘3’ — Does not apply otherwise (see Message Type in box 1a) (see Code list 2 in Annex II) an16   b MS of Submission Event Report Reference C — ‘R’ if <Message Type> is ‘1’ or ‘3’ and the MS of submission is different from the MS of event — ‘O’ if <Message Type> is ‘1’ or ‘3’ and the MS of submission is the MS of event — Does not apply otherwise (see Message Type in box 1a) The format of <MS of Submission Event Report Reference> is: — 2 alphabetic characters: Identifier of the National Administration of Submission of the event report — followed by a nationally assigned, unique code an..35   c Reference Number of Excise Office R     an8   d Member State of Event R   (see Code list 3 in Annex II to Commission Delegated Regulation (EU) 2022/1636) a2 3 EXCISE MOVEMENT C One of the <EXCISE MOVEMENT> or <OTHER ACCOMPANYING DOCUMENT> data groups must be present       a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   The value of the field must be greater than zero. n..2 4 OTHER ACCOMPANYING DOCUMENT C One of the <EXCISE MOVEMENT> or <OTHER ACCOMPANYING DOCUMENT> data groups must be present       a Other Accompanying Document Type R   The possible values are: 0 = Other 2 = (reserved) n1   b Short Description of Other Accompanying Document C — ‘R’ if <Other Accompanying Document Type> is ‘Other’ — It doesn’t apply otherwise — an..350   c Short Description of Other Accompanying Document_LNG C — ‘R’ if the corresponding text field(s) is (are) used — Does not apply otherwise — a2   d Other Accompanying Document Number R     an..350   e Other Accompanying Document Date R     date   f Image of Other Accompanying Document O         g Member State of Dispatch R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   h Member State of Destination R   A National Administration identified by a Country Code in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2 4.1 TRADER Person Involved in Movement O     9x   a Trader Excise Number C — At least one of the following attributes must be present: — <Trader Excise Number> — <Trader Identification> — <Trader Name> An existing identifier (Excise Number) <Trader Excise Number> in the set of <TRADER AUTHORISATION> or <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>. (see Code list 1 in Annex II to Regulation (EU) No 612/2013) an13   b Trader Identification C — At least one of the following attributes must be present: — <Trader Excise Number> — <Trader Identification> — <Trader Name> A VAT number or any other National number. an16   c Trader Name C — At least one of the following attributes must be present: — <Trader Excise Number> — <Trader Identification> — <Trader Name> — an..182   d Trader Person Type O   The possible values are the following: 1 = Consignor 2 = Consignee 3 = Tax representative 4 = Vendor 5 = Liable person 6 = Customer private individual n..2   e Member State Code C — ‘R’ if <Trader Name> is given AND <Trader Excise Number> and <Trader Identification> is not given. — It doesn’t apply otherwise (see Code list 3 in Annex II to Delegated Regulation (EU) 2022/1636) a2   f Street Name O     an..65   g Street Number O     an..11   h Postcode O     an..10   i City O     an..50   j NAD_LNG C — ‘R’ if the corresponding text field(s) is (are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   k Phone Number O     an..35   l Fax Number O     an..35   m Email Address O     an..70 4.2 GOODS ITEM O     999x   a Description of the Goods O     an..55   b CN Code C — ‘R’ if <OTHER ACCOMPANYING DOCUMENT. Image of Other Accompanying Document> is not present in the <OTHER ACCOMPANYING DOCUMENT> field — Does not apply otherwise (see Data group 4 and box 4f) The value of the Field must be greater than zero. n8   c Commercial Description of the Goods O     an..999   d Additional code O     an..35   e Quantity C — ‘R’ if <OTHER ACCOMPANYING DOCUMENT.Image of Other Accompanying Document> is not present in the <OTHER ACCOMPANYING DOCUMENT> field — Does not apply otherwise (see Data group 4 and box 4f) The value of the Field must be greater than zero. n..15,3   f Unit of Measure Code C — ‘R’ if <OTHER ACCOMPANYING DOCUMENT.Image of Other Accompanying Document> is not present in the <OTHER ACCOMPANYING DOCUMENT> field — Does not apply otherwise (see Data group 4 and box 4f) (See Annex II to Delegated Regulation (EU) 2022/1636, Code list 11) n..2   g Gross Mass O   The Gross Mass must be equal to or higher than Net Mass. The value of the Field must be greater than zero. n..16,6   h Net Mass O   The Gross Mass must be equal to or higher than Net Mass. The value of the Field must be greater than zero. n..16,6 4.3 MEANS OF TRANSPORT C — ‘R’ if <OTHER ACCOMPANYING DOCUMENT.Image of Other Accompanying Document> is not present in the <OTHER ACCOMPANYING DOCUMENT> field — Does not apply otherwise (see Data group 4 and box 4f)       a Trader Name R     an..182   b Street Name R     an..65   c Street Number O     an..11   d Transporter Country R   Provide a ‘Country Code’ listed in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2   e Postcode R     an..10   f City R     an..50   g Transport Mode Code R   Provide the mode of transport using the codes in Code list 6 of Annex II to Delegated Regulation (EU) 2022/1636 . n..2   h ACO_Complementary Information C — ‘R’ if <MEANS OF TRANSPORT.Transport Mode Code> is ‘Other’ — Does not apply otherwise (see Data group 4 box 4.3 g)   an..999   i ACO_Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is (are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   j Registration R     an..35   k Country of Registration R   Provide a ‘Country Code’ listed in Code list 3 of Annex II to Delegated Regulation (EU) 2022/1636. a2 5 EVENT REPORT R         a Date of Event R     date   b Place of Event R     an..350   c Place of Event_LNG C — ‘R’ if the corresponding text field is used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   d Excise Officer Identification O     an..35   e Submitting Person R     an..35   f Submitting Person Code R   (see Code list 10 in Annex II) n..2   g Submitting Person Complement C — ‘R’ if <Submitting Person Code> is ‘Other’ — ‘O’ otherwise (see Submitting Person Code in box 5f)   an..350   h Submitting Person Complement_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   i Changed Transport Arrangement O   The possible values are: 1 = Consignor 2 = Consignee 3 = Owner of goods 4 = Other n1   j Comments O     an..350   k Comments_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 6 EVIDENCE OF EVENT O     9x   a Issuing Authority O     an..35   b Issuing Authority_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   c Evidence Type Code R   (see Code list 6 in Annex II) n..2   d Evidence Type Complement C — ‘R’ <Evidence Type Code> is ‘Other’ — Does not apply otherwise (see Evidence Type Code in box 6c)   an..350   e Evidence Type Complement_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   f Reference of Evidence R     an..350   g Reference of Evidence_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   h Image of Evidence O       7 TRADER New Transport Arranger C — Does not apply if <Changed Transport Arrangement> is ‘1’, ‘2’, or is not used — ‘R’ otherwise (see Changed Transport Arrangement in box 5i)       a VAT Number O     an..14   b Trader Name R     an..182   c Street Name R     an..65   d Street Number O     an..11   e Postcode R     an..10   f City R     an..50   g NAD_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 8 TRADER New Transporter O         a VAT Number O     an..14   b Trader Name R     an..182   c Street Name R     an..65   d Street Number O     an..11   e Postcode R     an..10   f City R     an..50   g NAD_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 9 TRANSPORT DETAILS O     99x   a Transport Unit Code R   (see Code list 7 in Annex II to Delegated Regulation (EU) 2022/1636) n..2   b Identity of Transport Units C — Does not apply if <Transport Unit Code> is ‘Fixed transport installations’. — ‘R’ otherwise (see Transport Unit Code in box 9a)   an..35   c Identity of Commercial Seal O     an..35   d Seal Information O     an..350   e Seal Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   f Complementary Information O     an..350   g Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 10 EVENT REPORT Body C — ‘O’ if <TRADER New Transport Arranger> is used, or <TRADER New Transporter> is used, or <TRANSPORT DETAILS> is used — ‘R’ otherwise (see TRADER New Transport Arranger in Data group 7, TRADER New Transport in Data group 8, and TRANSPORT DETAILS in data group 9)   99x   a Event Type Code R   (see Code list 14 in Annex II) n..2   b Associated Information C — ‘R’ if <Event Type Code> is ‘0’ — ‘O’ otherwise (see Event Type Code in box 10a)   an..350   c Associated Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   d Body Record Unique Reference C — ‘R’ if <EXCISE MOVEMENT> field is present — Does not apply otherwise This value refers to the <Body Record Unique Reference> of the e-AD/e-SAD Body of the associated e-AD/e-SAD and must be unique within the message. The value of the Field must be greater than zero. n..3   e Description of the Goods C — ‘O’ if the <OTHER ACCOMPANYING DOCUMENT> field is present — Does not apply otherwise — an..55   f CN Code C — ‘R’ if the <OTHER ACCOMPANYING DOCUMENT> field is present — Does not apply otherwise The value of the Field must be greater than zero. n8   g Additional code C — ‘O’ if the <OTHER ACCOMPANYING DOCUMENT> field is present — Does not apply otherwise — an..35   h Indicator of Shortage or Excess C For 10 h and 10i: — ‘R’ if <Body Record Unique Reference> or <Description of the Goods> or <CN Code> or <Additional Code> is given — Does not apply otherwise (see Body Record Unique Reference in box 10d, Description of the Goods in box 10e, CN Code in box 10f and Additional Code in box 10g) The possible values are: S = Shortage E = Excess a1   i Observed Shortage or Excess C The value of the Field must be greater than zero. n..15,3 Table 13 (referred to in Article 12) Interruption of Movement A B C D E F G 1 ATTRIBUTES R         a ARC R   (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Date and Time of Issuance R     dateTime   c Reason for Interruption Code R   (see Code list 13 in Annex II) n..2   d Excise Office Reference Number R   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636]) an8   e Excise Officer Identification O     an..35   f Complementary Information C — ‘R’ if <Reason for Interruption Code> is ‘Other’ — ‘O’ otherwise (see Reason for Interruption Code in box 1c)   an..350   g Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field a2 2 CONTROL REPORT Reference O     9x   a Control Report Reference R   (see Code list 2 in Annex II) A ‘Control Report’ message exists in the system (including the case that it is encapsulated in a received ‘History of a movement’ message) having the same <Control Report Reference> and <ARC> with that of the submitted message. (see ARC in box 1a) an16 3 EVENT REPORT Reference O     9x   a Event Report Number R   (see Code list 2 in Annex II) An ‘Event Report’ message exists in the system (including the case that it is encapsulated in a received ‘History of a movement’ message) having the same <Event Report Number> and <ARC> with that of the submitted message (see ARC in box 1a) an16 Table 14 (as referred to in Article 13) Alert or Rejection of an e-AD/e-SAD A B C D E F G 1 ATTRIBUTES R         a Date and Time of Validation of Alert or Rejection C — R if the message is validated — Does not apply otherwise   dateTime 2 EXCISE MOVEMENT R         a ARC R   Provide the ARC of the e-AD/e-SAD. (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   The value of the field must be greater than zero. n..2 3 TRADER Consignee D ‘R’, except for Destination Type Code 8 (See Destination Type Code in box 1a of Table 1 in Delegated Regulation (EU) 2022/1636)       a Trader Identification C — ‘R’ if <Destination Type Code> is: —  — ‘Destination – Tax warehouse’ — ‘Destination – Registered consignee’ — ‘Destination – Temporary registered consignee’ — ‘Destination – Direct delivery’ — ‘Destination – Certified consignee’ — ‘Destination – Temporary certified consignee’ — "Destination – Return to the place of dispatch of the consignor, for a Duty Paid B2B movement" — ‘O’ if <Destination Type Code> is ‘Destination – Export’ — Does not apply otherwise The possible values of <Trader Identification> are described in the following table: an..16 Destination Type Code TRADER CONSIGNEE. Trader Identification 1 –  Destination – Tax warehouse Excise number (1) 2 –  Destination – Registered consignee Excise number (2) 3 –  Destination – Temporary registered consignee Temporary authorisation reference (4) 4 –  Destination – Direct delivery Excise number (3) 5 –  Destination – Exempted consignee (Does not apply) 6 –  Destination – Export VAT number (optional) 8 –  Destination – Unknown destination (consignee unknown) (Does not apply) 9 –  Destination – Certified consignee Excise number (5) 10 –  Destination – Temporary certified consignee Temporary authorisation reference (6) 11 –  Destination-Return to the place of dispatch of the consignor, for a Duty Paid B2B movement Excise Number (7) or Temporary Authorisation Reference (8) (1)  The operator type of the consignee is "Authorised warehouse keeper". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (2)  The operator type of the consignee is "Registered consignee". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (3)  The operator type of the consignee is either "Authorised warehouse keeper" or "Registered consignee". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (4)  The operator type of the consignee is "Temporary registered consignee". An existing <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>; (5)  The operator type of the consignee is "Certified consignee". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (6)  The operator type of the consignee is "Temporary certified consignee". An existing <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION>; (7)  The operator type of the consignee is "Certified consignor". An existing identifier <Trader Excise Number> in the set of <TRADER AUTHORISATION>; (8)  An existing <Temporary Authorisation Reference> in the set of <TEMPORARY AUTHORISATION> with Operator Type Code "Temporary Certified Consignor". (see Code list 1 and Code list 2 in Annex II to Regulation (EU) No 612/2013, if applicable)   b Trader Name R     an..182   c Street Name R     an..65   d Street Number O     an..11   e Postcode R     an..10   f City R     an..50   g NAD_LNG R   Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   h EORI Number C — ‘O’ if <Destination Type Code> is ‘Destination – Export’ Does not apply otherwise Provide the EORI number of the person responsible for lodging the export declaration as set out in Article 21(1) of Directive (EU) 2020/262. an..17 4 OFFICE OF DESTINATION R         a Office Reference Number R   (see Code list 4 in Annex II to Delegated Regulation (EU) 2022/1636) an8 5 ALERT OR REJECTION R         a Date of Alert or rejection R     date   b e-AD /e-SAD Rejected flag R   The format of Boolean is digital: ‘0’ or ‘1’ (‘0’ = No or False; ‘1’ = Yes or True). n1 6 ALERT OR REJECTION OF E-AD/E-SAD REASON Code C — ‘R’ if <e-AD/e-SAD Rejected flag> is True — ‘O’ if otherwise — 9x   a Alert or Rejection of Movement Reason Code R   (see Code list 5 in Annex II) n..2   b Complementary Information C — ‘R’ if <Alert or Rejection of Movement Reason Code> is ‘Other’ — ‘O’ otherwise (see Alert or Rejection of Movement Reason Code in box 6a)   an..350   c Complementary Information_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 Table 15 (as referred to in Article 6a) Manual Closure Request A B C D E F G 1 ATTRIBUTE R         a ARC R   Provide the ARC of the e-AD or e-SAD. (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   Provide the sequence number of the e-AD/e-SAD. n..2   c Manual Closure Request Reason Code R   (see code list 16 in Annex II) n1   d Manual Closure Request Reason Code Complement C — ‘R’ if <Manual Closure Request Reason Code> is ‘Other’ — ‘O’ otherwise   an..999   e Manual Closure Request Reason Code Complement_LNG C — ‘R’ if the corresponding text field is used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 2 SUPPORTING DOCUMENTS O     9x   a Short Description of Supporting Document C — ‘R’ if <Supporting Document Type> is ‘Other’ — Does not apply otherwise   an..999   b Short Description of Supporting Document_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   c Reference of Supporting Document C At least one, among these three fields, must be present: — <Supporting Document Type> — <Reference of Supporting Document> — <Image of Document> (see Image of Document in box 2e and Supporting Document Type in box 2f)   an..999   d Reference of Supporting Document_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   e Image of Document C At least one, among these three fields, must be present: — <Supporting Document Type> — <Reference of Supporting Document> — <Image of Document> (see Reference of Supporting Document in box 2c and Supporting Document Type in box 2f)       f Supporting Document Type C At least one, among these three fields, must be present: — <Supporting Document Type> — <Reference of Supporting Document> — <Image of Document> (see Reference of Supporting Document in box 2c and Image of Document in box 2e) (see code list 15 in Annex II) an..4 3 MANUAL CLOSURE Body O     999X   a Body Record Unique Reference R   This value refers to the <Body Record Unique Reference> of the Body of the associated e-AD / e-SAD and must be unique within the message. The value of this field must be greater than zero. n..3   b Indicator of Shortage or Excess O   The possible values are: S = Shortage E = Excess a1   c Observed Shortage or Excess C — ‘R’ if <Indicator of Shortage or Excess> is given — Does not apply otherwise (see Indicator of Shortage or Excess in box 3b) The value of the Field must be greater than zero. n..15,3   d Excise Product Code O   (see Code list 10 in Annex II to Delegated Regulation (EU) 2022/1636) an4   e Refused Quantity O   The value of this field must be greater than zero. n..15,3   f Complementary Information O     an..350   g Complementary Information_LNG C — ‘R’ if the corresponding text field is used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 Table 16 (as referred to in Article 14a) Manual Closure Response A B C D E F G 1 ATTRIBUTE R         a ARC R   Provide the ARC of the e-AD /e-SAD. (see Code list 2 in Annex II to Delegated Regulation (EU) 2022/1636) an21   b Sequence Number R   Provide the sequence number of the e-AD / e-SAD n..2   c Date of Arrival of Excise Products O   For excise goods under duty suspension: The date at which the movement ends in accordance with Article 19(2) of Council Directive (EU) 2020/262. For duty paid excise goods: The date at which the movement ends in accordance with Article 33(4) of Council Directive (EU) 2020/262. date   d Global Conclusion of Receipt O   The possible values are: 1 = Receipt accepted and satisfactory, 2 = Receipt accepted although unsatisfactory, 3 = Receipt refused, 4 = Receipt partially refused, 21 = Exit accepted and satisfactory, 22 = Exit accepted with minor discrepancies detected, 23 = Exit refused. n..2   e Complementary Information O     an..350   f Complementary Information_LNG C — ‘R’ if the corresponding text field is used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   g Manual Closure Request Reason Code R   (see code list 16 in Annex II) n1   h Manual Closure Request Reason Code Complement C — ‘R’ if <Manual Closure Request Reason Code> is ‘Other’ — ‘O’ otherwise   an..999   i Manual Closure Request Reason Code Complement_LNG C — ‘R’ if the corresponding text field is used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   j Manual Closure Request Accepted R   The format of Boolean is digital: ‘0’ or ‘1’ (‘0’ = No or False; ‘1’ = Yes or True). n1   k Manual Closure Rejection Reason Code C — ‘R’ if <Manual Closure Request Accepted> is ‘0’ — Does not apply otherwise (see code list 17 in Annex II) n1   l Manual Closure Rejection Complement C — ‘R’ if <Manual Closure Rejection Reason Code> is ‘Other’ — ‘O’ otherwise   an..999   m Manual Closure Rejection Complement_LNG C — ‘R’ if the corresponding text field is used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2 2 SUPPORTING DOCUMENTS O     9x   a Short Description of Supporting Document C — ‘R’ if <Supporting Document Type> is ‘Other’ — Does not apply otherwise   an..999   b Short Description of Supporting Document_LNG C — ‘R’ if the corresponding text field is used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   c Reference of Supporting Document C At least one, among these three fields, must be present: — <Supporting Document Type> — <Reference of Supporting Document> — <Image of Document> (see Image of Document in box 2e and Supporting Document Type in box 2f)   an..999   d Reference of Supporting Document_LNG C — ‘R’ if the corresponding text field(s) is(are) used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2   e Image of Document C At least one, among these three fields, must be present: — <Supporting Document Type> — <Reference of Supporting Document> — <Image of Document> (see Reference of Supporting Document in box 2c and Supporting Document Type in box 2f)       f Supporting Document Type C At least one, among these three fields, must be present: — <Supporting Document Type> — <Reference of Supporting Document> — <Image of Document> (see Reference of Supporting Document in box 2c and Image of Document in box 2e) (see code list 15 in Annex II) an..4 3 MANUAL CLOSURE Body O     999X   a Body Record Unique Reference R   This value refers to the <Body Record Unique Reference> of the Body of the associated e-AD /e-SAD and must be unique within the message. The value of this field must be greater than zero. n..3   b Indicator of Shortage or Excess O   The possible values are: S = Shortage E = Excess a1   c Observed Shortage or Excess C — ‘R’ if <Indicator of Shortage or Excess> is given — Does not apply otherwise (see Indicator of Shortage or Excess in box 3b) The value of the Field must be greater than zero. n..15,3   d Excise Product Code O   (see Code list 10 in Annex II to Delegated Regulation (EU) 2022/1636) an4   e Refused Quantity D — ‘O’ if <Global Conclusion of Receipt> is ‘Receipt partially refused’ — Does not apply otherwise The value of this field must be greater than zero. n..15,3   f Complementary Information O     an..350   g Complementary Information_LNG C — ‘R’ if the corresponding text field is used — Does not apply otherwise Provide the language code presented in Annex II to Delegated Regulation (EU) 2022/1636, Code list 1 to define the language used in this field. a2

ANNEX IISupplementary provisions

Open ↗

ANNEX II Lists of codes Code list 1: Follow-up correlation ID Field Content Field type Examples 1 Year Numeric 2 5 2 Identifier of the National Administration where the message was initially submitted Alphabetic 2 ES 3 Free nationally assigned, code Alphanumeric 21 ARC 4 Complement Alphanumeric 3 123 Field 1 is last two digits of year. Field 2 is taken from the list of Country Code (see Code list 3 in Annex II to Delegated Regulation (EU) 2022/1636) . Field 3 must be filled with a nationally assigned identifier. In certain cases, for the Follow-Up Correlation ID it can be an ARC. Field 4 gives a complement to field 3 to make together a unique identifier (for example, in the case of Follow-Up Correlation ID where several follow-up messages deal with the same ARC.) Code list 2: Event report number/Control report reference Field Content Field type Examples 1 Identifier of the National Administration where the report is validated Alphabetic 2 ES 2 Nationally assigned, unique code Alphanumeric 13 2005YTE17UIC2 3 Check digit Numeric 1 9 Field 1 is taken from the list of Country Code (see Code list 3 in Annex II to Delegated Regulation (EU) 2022/1636 ) Field 2 must be filled with a unique identifier per report. The way this field is used is under MSAs’ responsibility, but each report must have a unique number. It is possible, but not mandatory, that it contains the year when the report was initially submitted (as suggested in the example). Field 3 gives the check digit for the whole identifier, which will help detect an error when keying this identifier. Code list 3: Reasons for delayed result Code Description 1 Information not available 2 Confidential information 3 Ongoing investigation Code list 4: Refusal Reasons Code Description 0 Other 1 The enquiry or information requested could not be authorised under the laws or administrative practices of the requested Member State for its own use (e.g. Confidential information) 2 (reserved) 3 Disclosure contrary to the public policy of the state - The provision of information would lead to the disclosure of a commercial, industrial or professional secret or of a commercial process, or where its disclosure would be contrary to public policy 4 A judicial authority of the requested National Administration has refused to allow the transfer of information under its control 5 The request concerns information that is no longer available due to national rules of data retention (5 years or more minimum) 6 The requesting authority has not exhausted the usual sources of information which it could have used in the circumstances 7 The number and the nature of the requests for information made by the requesting authority within a specific period impose a disproportionate administrative burden on that requested authority 8 The requesting National Administration is unable, for legal reasons, to provide similar information 9 The consignor has not exhausted all the means available to him to obtain proof that the movement of excise goods between Member States has ended 10 No check performed 11 Out of scope of 389/2012 (e.g. Naples II) Code list 5: Alert or rejection of e-AD reasons Code Description 0 Other 1 The received e-AD/e-SAD does not concern the recipient 2 The excise product(s) does(do) not match with the order 3 The quantity(ies) does(do) not match with the order Code list 6: Evidence types Code Description 0 Other 1 Reserved 2 Police Report 3 Report other than Police or Customs 4 Customs Report Code list 7: Delay explanations Code Description 0 Other 1 Cancelled commercial transaction 2 Pending commercial transaction 3 Ongoing investigation by officials 4 Bad weather conditions 5 Strike 6 Accident Code list 8: Request Reason Code Description 0 Other 1 Report of receipt/export not returned to consignor 2 Excesses or shortages stated at arrival of goods 4 Submission of an e-AD/e-SAD was rejected because the consignee record of SEED did not match — the request is to ask for more information 6 Have goods/quantities specified on e-AD/e-SAD been entered in consignee’s stock records? 7 Check that goods have actually left EU (date on which export certified by customs) 8 Placing of goods under a suspensive customs procedure (export warehouse, victualling warehouse, outward processing, etc.) 9 Reimbursement of excise duty requested 10 Spot checks 11 Copy 3 not returned to Consignor 12 Reverse of Copy 3 endorsed to show excesses or losses 13 Certification of Receipt Incomplete 14 Consignee’s Excise Number not in SEED 15 Particular Deleted/Overwritten without official Endorsement 16 Request for Manual closure 17 Export Status Unknown 18 Request for Interruption of a movement 19 Perform interview of authorised representative 20 Fallback document 21 Two e-ADs/e-SADs were created for the same consignment 22 Clarification regarding type or quantity of goods 23 Receipt of goods were rejected/refused 24 Ongoing excise investigation 25 Suspicions of irregularity Code list 9: Request Actions Code Description 0 Other 2 Administrative control 3 Physical control 4 Confirm entry in trader's records 5 Confirm quantity received 6 Confirm authorisation of trader 7 Confirm the particulars in Box No(s) 11 Confirm identity of the carrier and the number of the vehicle 12 Confirm payment of duty 14 Confirm quantity dispatched 15 Confirm type of goods dispatched 16 Confirm Authenticity of Excise official stamp 17 Confirm Authenticity of Company's Stamp and Trader's signature 18 Confirm Trader's Authorisation and SEED Data 19 Manual closure 20 Hearing of authorised representative (e.g. interview of company manager) 21 Provide reason for shortage 22 Confirm shortage/excess/differences 23 Provide proof that the movement of excise goods has ended 24 Confirm purpose of goods or next purchaser of goods 25 Please see attached request 26 Follow-up measure needs to be taken from the Consignor 27 Correction required in Export declaration 28 Confirm the content of the Export Declaration 29 Inform if the movement has already been released by Customs 30 Provide Export MRN Code list 10: Event submitting persons Code Description 0 Other 1 Consignor 2 Consignee 3 Transporter 4 Excise officer 5 Other official Code list 11: Administrative cooperation action not possible reasons Code Description 0 Other 1 Missing information 2 Reserved 3 Missing time 4 Deep investigation on economic operator ongoing, short-term answer not possible 5 Trader could not be contacted 6 Missing trader Code list 12: Reasons for unsatisfactory receipt or control report Code Description 0 Other 1 Excess 2 Shortage 3 Goods damaged 4 Broken seal 5 Reported by ECS 7 Quantity higher than the one on the temporary authorisation Code list 13: Reasons for interruption Code Description 0 Other 1 Fraud suspected 2 Goods destroyed 3 Goods lost or stolen 4 Interruption requested at control Code list 14: Event types Code Description 0 Other 1 Accident 2 Goods destroyed 3 Goods stolen 6 Vehicle and goods stolen 7 Transhipment of goods Code list 15: Type of Document Code Description 0 Other 1 e-AD 2 e-SAD 3 Invoice 4 Delivery note 5 CMR 6 Bill of lading 7 Way Bill 8 Contract 9 Trader’s Application 10 Official record 11 Request 12 Answer 13 Fallback documents, Fallback Printout 14 Photo 15 Export Declaration 16 Anticipated Export Record 17 Exit Results 18 Custom Declaration 19 Certificate of independent small producer of alcoholic beverages <TARIC CODE> Any TARIC code used in Data Element 1203000000 (sub-element 002000)of the export declaration Code list 16: Manual Closure Request Reasons Code Description 0 Other 1 Export closed but no IE518 available 2 Consignee no longer connected to EMCS 3 Exempted consignee 4 Exit confirmed but no IE829 submitted (IE818 out of sequence) 5 No movement but cancellation no longer possible 6 Multiple issuances of e-ADs/e-SADs for a single movement 7 e-AD/e-SAD does not cover actual movement 8 Erroneous report of receipt 9 Erroneous rejection of an e-AD/e-SAD Code list 17: Manual Closure Rejection Reasons Code Description 0 Other 1 Evidence provided does not justify manual closure 2 Request Reason provided does not justify manual closure

Other acts of the same type
Council Implementing Regulation (EU) 2018/689 of 7 May 2018 implementing Article 15(3) of Regulation (EU) No 1352/2014 concerning restrictive measures in view of the situation in YemenCommission Implementing Regulation (EU) 2018/690 of 7 May 2018 amending Implementing Regulation (EU) No 540/2011 as regards the conditions of approval of the active substance fenazaquin (Text with EEA relevance. )Commission Implementing Regulation (EU) 2018/691 of 7 May 2018 approving the basic substance Talc E553B in accordance with Regulation (EC) No 1107/2009 of the European Parliament and of the Council concerning the placing of plant protection products on the market, and amending the Annex to Commission Implementing Regulation (EU) No 540/2011 (Text with EEA relevance. )Commission Implementing Regulation (EU) 2018/692 of 7 May 2018 renewing the approval of the active substance zoxamide in accordance with Regulation (EC) No 1107/2009 of the European Parliament and of the Council concerning the placing of plant protection products on the market, and amending the Annex to Commission Implementing Regulation (EU) No 540/2011 (Text with EEA relevance. )Commission Delegated Regulation (EU) 2018/1108 of 7 May 2018 supplementing Directive (EU) 2015/849 of the European Parliament and of the Council with regulatory technical standards on the criteria for the appointment of central contact points for electronic money issuers and payment service providers and with rules on their functions (Text with EEA relevance.)Commission Regulation (EU) 2018/681 of 4 May 2018 amending the Annex to Regulation (EU) No 231/2012 laying down specifications for food additives listed in Annexes II and III to Regulation (EC) No 1333/2008 of the European Parliament and of the Council as regards specifications for Polyvinyl alcohol-polyethylene glycol graft-co-polymer (E 1209) (Text with EEA relevance. )Commission Regulation (EU) 2018/682 of 4 May 2018 amending Annex II to Regulation (EC) No 1333/2008 of the European Parliament and of the Council as regards the use of polyglycerol polyricinoleate (E 476) in emulsified sauces (Text with EEA relevance. )Commission Regulation (EU) 2018/683 of 4 May 2018 imposing a provisional anti-dumping duty on imports of certain pneumatic tyres, new or retreaded, of rubber, of a kind used for buses or lorries, with a load index exceeding 121 originating in the People's Republic of China, and amending Implementing Regulation (EU) 2018/163Commission Regulation (EU) 2018/686 of 4 May 2018 amending Annexes II and III to Regulation (EC) No 396/2005 of the European Parliament and of the Council as regards maximum residue levels for chlorpyrifos, chlorpyrifos-methyl and triclopyr in or on certain products (Text with EEA relevance)Commission Regulation (EU) 2018/687 of 4 May 2018 amending Annexes II and III to Regulation (EC) No 396/2005 of the European Parliament and of the Council as regards maximum residue levels for acibenzolar-S-methyl, benzovindiflupyr, bifenthrin, bixafen, chlorantraniliprole, deltamethrin, flonicamid, fluazifop-P, isofetamid, metrafenone, pendimethalin and teflubenzuron in or on certain products (Text with EEA relevance)Commission Implementing Regulation (EU) 2018/730 of 4 May 2018 laying down technical information for the calculation of technical provisions and basic own funds for reporting with reference dates from 31 March 2018 until 29 June 2018 in accordance with Directive 2009/138/EC of the European Parliament and of the Council on the taking-up and pursuit of the business of Insurance and Reinsurance (Text with EEA relevance. )Commission Regulation (EU) 2018/676 of 3 May 2018 correcting Commission Regulation (EU) No 546/2011 implementing Regulation (EC) No 1107/2009 of the European Parliament and of the Council as regards uniform principles for evaluation and authorisation of plant protection products (Text with EEA relevance. )

Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.

Contents

What to look at next