Regulation (EU) 2026/1738 of the European Parliament and of the Council of 8 July 2026 on circularity requirements for vehicle design and on management of end-of-life vehicles, amending Regulations (EU) No 168/2013, (EU) 2018/858, (EU) 2019/1020 and (EU) 2023/1542 and repealing Directives 2000/53/EC and 2005/64/EC (Text with EEA relevance)
Subject matter
This Regulation lays down circularity requirements on vehicle design and production related to reusability, recyclability and recoverability and the use of recycled content, which are to be verified at type-approval of vehicles, and on information and labelling requirements on parts, components and materials in vehicles. It also lays down requirements on extended producer responsibility, collection and treatment of end-of-life vehicles, as well as on the export of used vehicles from the Union to third countries.
Scope
1. This Regulation shall apply:
(a)
to vehicles and end-of-life vehicles of categories M 1 and N 1 as referred to in Article 4(1), points (a)(i) and (b)(i), of Regulation (EU) 2018/858;
(b)
from 1 September 2029, to special purpose vehicles and end-of-life special purpose vehicles, as defined in Article 3, point (31), of Regulation (EU) 2018/858, of categories M 1 and N 1 ;
(c)
from 1 September 2031 to vehicles and end-of-life vehicles of categories M 2 , M 3 , N 2 , N 3 and O as referred to in Article 4(1) of Regulation (EU) 2018/858;
(d)
from 1 September 2031, to special purpose vehicles and end-of-life special purpose vehicles, as defined in Article 3, point (31), of Regulation (EU) 2018/858, of categories M 2 , M 3 , N 2 , N 3 and O;
(e)
from 1 September 2031, to vehicles and end-of-life vehicles of L-category, as referred to in Article 4(2) of Regulation (EU) No 168/2013 of the European Parliament and of the Council ( 33 ) .
2. Notwithstanding paragraph 1, this Regulation shall not apply to:
(a)
vehicles produced in small series, as defined in Article 3, point (30), of Regulation (EU) 2018/858;
(b)
L-category vehicles produced in small series as referred to in Article 42 of Regulation (EU) No 168/2013;
(c)
vehicles designed and constructed or adapted for use by the armed services only, as referred to in Article 2(2), point (d), of Regulation (EU) 2018/858;
(d)
vehicles designed and constructed for use by the armed services, civil defence, fire services, forces responsible for maintaining public order and emergency medical services, as referred to in Article 2(2), point (e), of Regulation (EU) No 168/2013;
(e)
vehicles of historical interest as defined in Article 3, point (7), of Directive 2014/45/EU, including their identifiable parts and components required for their maintenance activities and necessary to preserve their historical status for the period during which these vehicles are considered to be vehicles of historical interest;
(f)
vehicles of special cultural interest for the period during which these vehicles are officially recognised as such by competent authorities and in accordance with the procedure set out in Annex II to this Regulation;
(g)
trailer caravans as referred to in point 5.6 of Annex I to Regulation (EU) 2018/858;
(h)
special purpose vehicles as defined in Article 3, point (31), of Regulation (EU) 2018/858 of categories M 2 , M 3 , N 2 , N 3 or O that are produced by a small-volume manufacturer;
(i)
cycles designed to pedal of L1 e -A-category, as referred to in criterium (9) of Annex I to Regulation (EU) No 168/2013, or L1 e -B, as referred to in point 1.1.2. of Annex XIX to Commission Delegated Regulation (EU) No 3/2014 ( 34 ) .
3. Notwithstanding paragraph 1, point (c), the following provisions shall not apply to vehicles and end-of-life vehicles of categories M 2 , M 3 , N 2 , N 3 and O:
(a)
Article 4 on reusability, recyclability and recoverability of vehicles;
(b)
Article 5 on requirements for substances in vehicles;
(c)
Article 6 on minimum recycled content in vehicles;
(d)
Article 8 on general obligations;
(e)
Article 9 on circularity strategy;
(f)
Article 10 on declaration on recycled content present in vehicles;
(g)
Article 12 on labelling of parts, components and materials present in vehicles;
(h)
Article 13 on Digital Circularity Vehicle Passport;
(i)
Article 21 on fee modulation;
(j)
Article 22 on cost allocation mechanism for vehicles becoming end-of-life vehicles in another Member State;
(k)
Article 33 on reuse, recycling and recovery targets;
(l)
Article 35(2) on shipments of end-of-life vehicles.
4. Notwithstanding paragraph 1, point (e), the following provisions shall not apply to L-category vehicles or end-of-life vehicles:
(a)
Article 4 on reusability, recyclability and recoverability of vehicles;
(b)
Article 5 on requirements for substances in vehicles;
(c)
Article 6 on minimum recycled content in vehicles;
(d)
Article 9 on circularity strategy;
(e)
Article 10 on declaration on recycled content present in vehicles;
(f)
Article 13 on Digital Circularity Vehicle Passport;
(g)
Article 21 on fee modulation;
(h)
Article 22 on cost allocation mechanism for vehicles becoming end-of-life vehicles in another Member State;
(i)
Article 33 on reuse, recycling and recovery targets;
(j)
Article 35(2) on shipments of end-of-life vehicles;
(k)
Article 38 on competent authority for export of used vehicles to third countries;
(l)
Article 39 on controls and requirements on the export of used vehicles;
(m)
Article 40 on automated verification of the information on vehicle status;
(n)
Article 41 on risk management and customs controls;
(o)
Article 42 on suspension;
(p)
Article 43 on release for export;
(q)
Article 44 on refusal to release for export;
(r)
Article 45 on cooperation among authorities and exchange of information;
(s)
Article 46 on electronic systems.
5. Notwithstanding paragraph 1, points (b) and (d), the following provisions shall not apply to special purpose vehicles or end-of-life special purpose vehicles:
(a)
Article 4 on reusability, recyclability and recoverability of vehicles;
(b)
Article 6 on minimum recycled content in vehicles;
(c)
Article 7 on design to enable removal and replacement of certain parts and components in vehicles;
(d)
Article 8 on general obligations;
(e)
Article 9 on circularity strategy;
(f)
Article 10 on declaration on recycled content present in vehicles;
(g)
Article 11 on information on removal and replacement of parts, components and materials present in vehicles;
(h)
Article 12 on labelling of parts, components and materials present in vehicles;
(i)
Article 13 on Digital Circularity Vehicle Passport;
(j)
Article 14 on competent authority for management of end-of-life vehicles;
(k)
Article 15 on authorised treatment facilities;
(l)
Article 17 on Producer Responsibility Organisations;
(m)
Article 18 on authorisation on fulfilment of extended producer responsibility;
(n)
Article 19 on registration;
(o)
Article 21 on fee modulation;
(p)
Article 22 on cost allocation mechanism for vehicles becoming end-of-life vehicles in another Member State;
(q)
Article 33 on reuse, recycling and recovery targets;
(r)
Article 35(2) on shipments of end-of-life vehicles;
(s)
Article 36 on transfer of ownership of used vehicles within the Union;
(t)
Article 37(1) on status of the vehicle;
(u)
Article 38 on competent authority for export of used vehicles to third countries;
(v)
Article 39 on controls and requirements on the export of used vehicles;
(w)
Article 40 on automated verification of the information on vehicle status;
(x)
Article 41 on risk management and customs controls;
(y)
Article 42 on suspension;
(z)
Article 43 on release for export;
(aa)
Article 44 on refusal to release for export;
(ab)
Article 45 on cooperation among authorities and exchange of information;
(ac)
Article 46 on electronic systems.
6. Notwithstanding paragraph 1, the following shall apply:
(a)
Articles 4 to 13 shall not apply to parts of a vehicle that have been type-approved in a multi-stage type-approval of category M 2 , M 3 , N 2 , N 3 or O other than the base vehicle; the other provisions of this Regulation apply to the extent that they apply to the category of the vehicle concerned;
(b)
Article 5 shall not apply to special purpose vehicles of categories M 2 , M 3 , N 2 , N 3 or O;
(c)
Articles 7 and 11 shall apply to L-category vehicles only with respect to entries 1, 2, 3, 4, 5, 7, 10 and 11 of Part C of Annex VIII;
(d)
Article 7 shall apply to vehicles of categories M 2 , M 3 , N 2 , N 3 and O only with respect to entries 1, 3, 4 and 5 of Part C of Annex VIII;
(e)
Article 8 shall apply to L-category vehicles only with respect to the obligations applicable for such vehicles;
(f)
Article 16, point (b), shall not apply to L-category vehicles and vehicles of categories M 2 , M 3 , N 2 , N 3 , or O and special purpose vehicles of categories M 1 , M 2 , M 3 , N 1 , N 2 , N 3 , or O;
(g)
Member States may exempt L1e, L2e and L6e-category vehicles from the obligations under Article 23(6) and Articles 25, 36 and 37;
(h)
for L-category vehicles and vehicles of categories M 2 , M 3 , N 2 , N 3 , and O and for special purpose vehicles of categories M 2 , M 3 , N 2 , N 3 and O, Article 29 shall only apply with respect to entries 1, 2, 3, 4, 5, 7, 10 and 11 of Part C of Annex VIII;
(i)
for L-category vehicles and for vehicles of categories M 2 , M 3 , N 2 , N 3 and O, Articles 47 to 50 shall only apply with respect to reporting and enforcement of obligations applicable for such vehicle categories.
Definitions
For the purposes of this Regulation, the following definitions shall apply:
(1)
‘vehicle’ means any vehicle as defined in Article 3, point (15), of Regulation (EU) 2018/858 or listed in Article 4(2) of Regulation (EU) No 168/2013;
(2)
‘end-of-life vehicle’ means a vehicle which is waste as defined in Article 3, point (1), of Directive 2008/98/EC, or which is waste according to Annex I of this Regulation;
(3)
‘vehicle type’ means any type of vehicle as defined in Article 3, point (32), of Regulation (EU) 2018/858 or vehicle type as defined in Article 3, point (73), of Regulation (EU) No 168/2013;
(4)
‘reuse’ means any operation by which parts or components of end-of-life vehicles are used again for the same purpose for which they were conceived;
(5)
‘reusability’ means the possibility for reuse of parts or components diverted from an end-of-life vehicle;
(6)
‘recyclability’ means the possibility for recycling of parts, components or materials diverted from an end-of-life vehicle;
(7)
‘recoverability’ means the possibility for recovery of parts, components or materials diverted from an end-of-life vehicle;
(8)
‘supplier’ means any natural or legal person who supplies parts, components or materials to a manufacturer who uses them to manufacture vehicles;
(9)
‘plastic’ means a polymer within the meaning of Article 3, point (5), of Regulation (EC) No 1907/2006, to which additives or other substances may have been added and which can function as a main structural component of final products, with the exception of natural polymers that have not been chemically modified;
(10)
‘critical raw materials’ means critical raw materials within the meaning of Article 4(1) of Regulation (EU) 2024/1252;
(11)
‘pre-consumer waste’ means material diverted from the waste stream during a manufacturing process, excluding reutilisation of materials such as rework, regrind or scrap generated in a process and capable of being reclaimed within the same process that generated it;
(12)
‘post-consumer waste’ means waste that is generated from products that have been placed on the market or supplied for distribution, consumption or use in a third country in the course of a commercial activity, whether in return for payment or free of charge;
(13)
‘removal’ means manual, mechanical, chemical, thermal or metallurgic handling with the result that the targeted parts, components or materials from end-of-life vehicles are individually identifiable as a separate output stream or part of an output stream;
(14)
‘e-drive motor’ means an electric motor that converts electrical input power into mechanical output power to provide traction to a vehicle;
(15)
‘electric vehicle battery’ means electric vehicle battery as defined in Article 3(1), point (14), of Regulation (EU) 2023/1542;
(16)
‘authorised treatment facility’ means any establishment or undertaking that is permitted in accordance with Directive 2008/98/EC and this Regulation to carry out collection, storage and treatment operations of end-of-life vehicles, including their parts and components;
(17)
‘shredding’ means an operation used for tearing into pieces or fragmenting end-of-life vehicles;
(18)
‘treatment’ means any activity taking place after the end-of-life vehicle has been handed over to a facility for depollution, dismantling, compacting, shearing, shredding, recovery or preparation prior to disposal of the shredder waste, and another operation carried out for the recovery or disposal of the end-of-life vehicle and its parts, components and materials;
(19)
‘repair and maintenance operator’ means a natural or legal person who pursues a professional activity directly or indirectly involving the repair and maintenance of vehicles, including repairers, manufacturers or distributors of repair equipment, tools or spare parts, as well as publishers of technical information, automobile clubs, roadside assistance operators, operators offering inspection and testing services, operators offering training for installers as well as manufacturers and repairers of equipment for alternative-fuel vehicles;
(20)
‘making available on the market’ means a supply of a vehicle for distribution or use on the market in the course of a commercial activity, whether in return for payment or free of charge;
(21)
‘placing on the market’ means making available a vehicle for the first time on the Union market;
(22)
‘waste management operator’ means any natural or legal person dealing on a professional basis with the collection or treatment of end-of-life vehicles, including their parts and components;
(23)
‘producer’ means any manufacturer, importer or distributor who, irrespective of the selling technique used, including by means of distance contracts as defined in Article 2, point (7), of Directive 2011/83/EU of the European Parliament and of the Council ( 35 ) , makes available a vehicle for the first time for distribution or use, within a territory of a Member State on a professional basis;
(24)
‘producer responsibility organisation’ means a legal entity that financially or financially and operationally organises the fulfilment of extended producer responsibility obligations on behalf of several producers;
(25)
‘authorised representative for the extended producer responsibility’ means a natural or legal person established in a Member State in which the producer makes vehicles available on the market for the first time, other than the Member State or the third country where the producer is established, and is appointed by the producer in accordance with Article 8a(5), third subparagraph, of Directive 2008/98/EC to fulfil the obligations of that producer under Chapter IV of this Regulation;
(26)
‘authorised representative for the cross-border mechanism’ means a natural or legal person established in a Member State and appointed by the manufacturer in accordance with Article 22;
(27)
‘secondary raw materials’ means materials that can substitute for primary raw materials and that have been obtained through recycling processes;
(28)
‘vehicle owner’ means any natural or legal person holding the ownership right of a vehicle or the holder of the vehicle registration certificate or, if neither the holder of the ownership right nor the holder of the vehicle registration certificate can be identified, the holder of the vehicle;
(29)
‘post-shredder technology’ means techniques and technologies used to process materials from end-of-life vehicles, after they have been shredded, for further recovery in accordance with Part G, point 2, of Annex VIII;
(30)
‘remanufacturing’ means professional actions through which a new part or component is manufactured to return to same-as-new condition from parts and components that are removed from vehicles or end-of-life vehicles and through which at least one change is made that affects the safety, lifetime, performance, purpose or type of the part or component, in a process that is in compliance with specific technical specifications, including engineering, quality and testing standards;
(31)
‘refurbishment’ means actions carried out to prepare, clean, test, service and, where necessary, repair a part or component that is removed from vehicles or end-of-life vehicles in order to restore its performance or functionality within the intended use and range of performance originally conceived at the design stage at the time of the placing of the part or component on the market;
(32)
‘non-inert waste’ means waste that does not meet the conditions of definition of ‘inert waste’ laid down in Article 2, point (e), of Council Directive 1999/31/EC ( 36 ) ;
(33)
‘used vehicle’ means a vehicle which has been registered in a Member State or a third country and is not an end-of-life vehicle;
(34)
‘used vehicle to be exported’ means a used vehicle that is to be placed under the customs procedure, as laid down in Article 269 of Regulation (EU) No 952/2013;
(35)
‘economic operator’ means a producer, collector, vehicle insurance company, supplier, repair and maintenance operator, waste management operator, including a dismantler or recycler, and any other operator involved in design of vehicles, trade in used vehicles, dismantling, reuse, or management of end-of-life vehicles, remanufacturing and refurbishment of parts, components and materials from vehicles;
(36)
‘roadworthy vehicle’ means a vehicle that is roadworthy in accordance with Directive 2014/45/EU;
(37)
‘retrofit operator’ means any legal person that manufactures an electric conversion kit or performs the conversion of internal combustion engine vehicles to battery-electric or fuel cell vehicles;
(38)
‘collection point’ means an economic operator, other than an authorised treatment facility, which temporarily stores end-of-life vehicles and prepares the transfer of the collected end-of-life vehicles to authorised treatment facilities for treatment;
(39)
‘waste’, ‘waste oils’, ‘waste holder’, ‘waste management’, ‘collection’, ‘prevention’, ‘recovery’, ‘recycling’, ‘backfilling’, ‘disposal’ and ‘extended producer responsibility scheme’ mean waste, waste oils, waste holder, waste management, collection, prevention, recovery, recycling, backfilling, disposal and extended producer responsibility scheme as defined in Article 3, points (1), (3), (6), (9), (10), (12), (15), (17), (17a), (19) and (21), respectively, of Directive 2008/98/EC;
(40)
except for L-category vehicles: ‘type-approval’, ‘multi-stage type-approval’, ‘component’, ‘parts’, ‘spare parts’, ‘base vehicle’, ‘vehicle produced in small series’, ‘special purpose vehicle’, ‘market surveillance authority’, ‘approval authority’, ‘manufacturer’, ‘importer’ and ‘distributor’ mean type-approval, multi-stage type-approval, component, parts, spare parts, base vehicle, vehicle produced in small series, special purpose vehicle, market surveillance authority, approval authority, manufacturer, importer and distributor as defined in Article 3, points (1), (8), (19), (21), (23), (24), (30), (31), (35), (36), (40), (42) and (43), respectively, of Regulation (EU) 2018/858;
(41)
for L-category vehicles: ‘type-approval’, ‘base vehicle’, ‘component’, ‘parts’, ‘spare parts’, ‘manufacturer’, ‘importer’, ‘distributor’, ‘approval authority’ and ‘market surveillance authority’ mean type-approval, base vehicle, component, parts, spare parts, manufacturer, importer, distributor, approval authority, and market surveillance authority as defined in Article 3, points (1), (11), (16), (18), (21), (47), (49), (50), (56) and (57), respectively, of Regulation (EU) No 168/2013, and ‘vehicle produced in small series’ means vehicle produced in small series as referred to in Article 42 of that Regulation;
(42)
‘registration’, ‘registration certificate’, ‘holder of registration certificate’, ‘suspension’ and ‘cancellation of registration’ mean registration, registration certificate, holder of registration certificate, suspension and cancellation of registration as defined in Article 2, points (b), (c), (d), (e) and (f), respectively, of Directive 1999/37/EC;
(43)
‘vehicle of historical interest’, ‘roadworthiness test’ and ‘roadworthiness certificate’ mean vehicle of historical interest, roadworthiness test and roadworthiness certificate as defined in Article 3, points (7), (9) and (12), respectively, of Directive 2014/45/EU;
(44)
‘substance of concern’ and ‘data carrier’ mean substance of concern and data carrier as defined in Article 2, points (27) and (29), respectively, of Regulation (EU) 2024/1781;
(45)
‘customs authorities’ means customs authorities as defined in Article 5, point (1), of Regulation (EU) No 952/2013;
(46)
‘online platform’ means online platform as defined in Article 3, point (i), of Regulation (EU) 2022/2065;
(47)
‘small-volume manufacturer’ means small-volume manufacturer as defined in Article 3, point (48), of Regulation (EU) 2024/1257;
(48)
‘light means of transport battery’ or ‘LMT battery’ means light means of transport battery or LMT battery, respectively, as defined in Article 3, point (11), of Regulation (EU) 2023/1542;
(49)
‘packaging waste’ means packaging waste as defined in Article 3, point (25), of Regulation (EU) 2025/40 of the European Parliament and of the Council ( 37 ) ;
(50)
‘waste electrical and electronic equipment’ means waste electrical and electronic equipment as defined in Article 3(1), point (e), of Directive 2012/19/EU of the European Parliament and of the Council ( 38 ) ;
(51)
‘biobased plastics’ means biobased plastics as defined in Article 3, point 53, of Regulation (EU) 2025/40;
(52)
‘reclamation’ means reclamation as defined in Article 3, point (13), of Regulation (EU) 2024/573.
Reusability, recyclability and recoverability of vehicles
1. Each vehicle belonging to a vehicle type that is type-approved as from 1 September 2032 under Regulation (EU) 2018/858 shall be constructed so that it is:
(a)
reusable or recyclable to a minimum of 85 % by mass;
(b)
reusable or recoverable to a minimum of 95 % by mass.
2. For each vehicle type referred to in paragraph 1, manufacturers shall take the following measures:
(a)
collect the necessary data through the full chain of supply, in particular the nature and the mass of all materials used in the construction of the vehicles, to ensure continued compliance with this Regulation;
(b)
keep all the other appropriate vehicle data required by the calculation process referred to in point (e);
(c)
establish procedures to verify the correctness and completeness of the information received from the suppliers;
(d)
manage and document the breakdown of the materials;
(e)
calculate the reusability, recyclability and recoverability rates for the purposes of paragraph 1 of this Article in accordance with the methodology established by the Commission under paragraph 3 of this Article or, before such methodology has been adopted and entered into application, in accordance with international standard ISO 22628:2002 in combination with the elements set out in Part A of Annex III to this Regulation;
(f)
mark the parts and components of the vehicles made of polymers and elastomers in accordance with Article 12(1);
(g)
ensure that parts and components listed in Part E of Annex VIII are not reused in the construction of new vehicles.
3. The Commission shall, by 28 February 2029, adopt an implementing act establishing a new methodology for calculation and verification of the rates of reusability, recyclability and recoverability of a vehicle, taking into account the elements set out in Annex III to this Regulation and international standard ISO 22628:2002. That implementing act shall be adopted in accordance with the examination procedure referred to in Article 52(2).
Requirements for substances in vehicles
1. The presence of substances of concern in vehicles and in their parts and components shall be minimised as far as possible.
2. By 14 February 2028, the Commission shall prepare a report on the presence of substances of concern in vehicles, to determine the extent to which they negatively affect the reuse and recycling of materials or have an adverse effect on the environment or health. The Commission shall be assisted by the Agency on aspects of chemical safety. The report shall not cover substances of concern in vehicle parts and components for which an identification or assessment is already required by other Union legislation. The Commission shall submit the report to the European Parliament and to the Council, setting out its findings, and consider the appropriate follow-up measures. If a Member State considers that a substance negatively affects the reuse and recycling of materials in a vehicle in which it is present, it shall, by 14 February 2029, supply such information to the Commission and, on aspects of chemical safety, also to the Agency and, where available, refer to any relevant risk assessments or other relevant data.
3. The Commission is empowered to adopt delegated acts in accordance with Article 51 to supplement this Regulation by establishing information requirements and restrictions for the presence of substances of concern that negatively affect the reuse and recycling of materials in vehicles and in their parts and components for reasons not relating primarily to chemical safety.
4. Any vehicle type that is type-approved as from 1 September 2032, under Regulation (EU) 2018/858, or any new parts or components placed on the market for such a vehicle shall not contain lead, mercury, cadmium or hexavalent chromium.
5. By way of derogation from paragraph 4 of this Article, vehicle types or parts and components placed on the market for such vehicles may contain lead, mercury, cadmium or hexavalent chromium under the conditions and up to the maximum concentration values laid down in Annex IV to this Regulation. Paragraphs 2, 3 and 4 of this Article and this paragraph shall not apply to batteries incorporated in vehicles to which Regulation (EU) 2023/1542 applies.
6. The Commission is empowered to adopt delegated acts in accordance with Article 51 to amend Annex IV in order to adapt it to scientific and technical progress by:
(a)
establishing maximum concentration values up to which the presence of lead, mercury, cadmium or hexavalent chromium in specific parts, components and homogenous materials of vehicles is to be tolerated;
(b)
exempting certain parts, components and homogenous materials of vehicles from the prohibition on the presence of lead, mercury, cadmium or hexavalent chromium set out in paragraph 4 where the following conditions are fulfilled:
(i)
the use of those substances is unavoidable;
(ii)
it is demonstrated that socio-economic benefits outweigh the risk to the environment or human health arising from the use of those substances;
(iii)
there are no suitable alternative substances or technologies;
(c)
deleting parts, components and homogenous materials of vehicles from Annex IV, if the use of lead, mercury, cadmium or hexavalent chromium is avoidable;
(d)
designating the parts, components and homogenous materials of vehicles that are to be removed before further treatment and require them to be labelled or made identifiable by other appropriate means.
The Commission is empowered to adopt delegated acts in accordance with Article 51 to amend Annex IV, in particular by removing certain exemptions for homogenous materials and components from the list, in cases where the specific exemption is addressed under other Union legislation.
When adopting a delegated act pursuant to this paragraph, the Commission shall take into account the socio-economic impact of introducing, modifying or deleting an exemption to the restriction on the use of lead, mercury, cadmium or hexavalent chromium in vehicle types, including the availability of alternatives and the impacts on the environment and human health across the full lifecycle of vehicles.
7. Upon request from the Commission, the Agency shall prepare within 12 months a report, based inter alia on consultation with stakeholders, on the technical and economic feasibility of alternatives to existing exemptions listed in Annex IV and, based on such assessment, a duly reasoned proposal for the specific amendment of any such exemption.
8. As soon as it receives the request from the Commission, the Agency shall publish on its website a notice that a report on a possible amendment of an exemption listed in Annex IV will be prepared and invite Member States and all interested parties to submit comments within 12 weeks of the date of publication of that notice. The Agency shall publish on its website all comments received from Member States and interested parties.
9. At the latest 12 months following the submission of the report referred to in paragraph 7 to the Commission, the Committee for Socio-economic Analysis of the Agency, set up pursuant to Article 76(1), point (d), of Regulation (EC) No 1907/2006, shall adopt an opinion on the report and on the specific amendments proposed. The Agency shall submit that opinion to the Commission without delay.
Minimum recycled content in vehicles
1. The plastic contained in each new vehicle type that is type-approved as from 1 September 2032 under Regulation (EU) 2018/858 shall contain a minimum of 15 % of plastic recycled by weight from post-consumer plastic waste.
The plastic contained in each new vehicle type that is type-approved as from 1 September 2036 under Regulation (EU) 2018/858 shall contain a minimum of 25 % of plastic recycled by weight from post-consumer plastic waste.
2. At least 20 % of the target set out in paragraph 1 shall be achieved by including in the vehicle type concerned plastics recycled from end-of-life vehicles or from parts and components removed from vehicles during the use phase.
3. The weight of the plastic contained in each new vehicle type concerned and the weight of recycled plastic referred to in paragraphs 1 and 2 shall exclude elastomers from tyres and from thermosets other than polyurethane foams used for cushioning.
4. For the purposes of the obligations laid down in paragraphs 1, 2, and 3, recycled content shall be recovered from post-consumer waste, which has been recycled either in:
(a)
an installation located in the Union; or
(b)
from 14 August 2030, an installation located in a third country, provided that such installation meets the requirements of Annex XIII.
By 30 September 2028, the Commission shall more comprehensively assess the expected impact on global trade, as well as on the Union recycling and automotive industries and report its assessment to the European Parliament and to the Council.
5. By 31 August 2028, the Commission shall adopt an implementing act in accordance with Article 52(2) to establish the methodology for the calculation and verification, for the purposes of paragraphs 1 to 4 of this Article, of the share of plastics recycled from post-consumer waste, and from end-of-life vehicles, present in and incorporated into vehicle types.
A mass balance accounting methodology shall apply to recycled plastic obtained from recycling methods other than mechanical recycling, in line with the mass balance accounting methodologies applicable to plastics recycling in line with the definition of recycling in Directive 2008/98/EC.
The verification methodology shall include an obligation for manufacturers to ensure that each installation located in a third country producing recycled content material that they are using complies with Annex XIII, and that each such installation located in a third country is being audited at least every five years by an independent third-party entity pursuant to Annex XIV. Those audits shall verify that the conditions set out in paragraphs 1 to 4 of this Article are met.
The audit requirement set out in the third subparagraph of this paragraph and the requirements and criteria set out in Annex XIII for material recycled in third countries shall apply from 14 August 2030.
6. The Commission shall be empowered to adopt delegated acts in accordance with Article 51 to supplement paragraphs 1 and 2 of this Article by laying down temporary derogations to the recycled plastic content targets, or timing in the event that lack of availability or excessive prices of specific recycled plastics make compliance with the minimum percentages of recycled content excessively difficult.
7. By 30 September 2027, the Commission shall assess the feasibility of establishing a requirement on the minimum share of recycled steel, considering in particular the following:
(a)
the current and forecast availability of ferrous scrap, considering flat and long steel and, where relevant, stainless-steel product families;
(b)
the current share of ferrous scrap in various steel semi-products and intermediates related to steel families used in vehicles and expected changes related to the transition of the automotive industry;
(c)
the potential uptake of ferrous scrap by manufacturers in vehicles to be type-approved in the future and the respective potential contribution to higher scrap utilisation levels considering the different compositional constraints applicable to each steel product family;
(d)
the relative demand of the automotive sector in comparison to the demand for ferrous scrap of other sectors, considering the ability to tolerate copper content and other unintended tramp inclusions;
(e)
economic viability, technical and scientific progress, including changes in the availability of recycling technologies concerning steel recycling rates, as well as the necessity to address market failures hindering the utilisation of post-consumer versus pre-consumer steel scrap;
(f)
the contribution of a minimum share of recycled content of steel in vehicles to the Union’s open strategic autonomy, climate, environmental and industrial objectives, in particular as regards the creation of complementary lead markets for decarbonised steel production;
(g)
the need to prevent disproportionate negative impacts on the affordability of vehicles; and
(h)
the influence on the overall costs and competitiveness of the automotive sector and the entire automotive steel value chain.
By 30 September 2028, the Commission shall adopt a delegated act, in accordance with Article 51, to supplement this Regulation by establishing a minimum share of steel recycled from post-consumer steel waste and, where relevant, ferrous scrap to be present in and incorporated into vehicle types to be type-approved in accordance with this Regulation and Regulation (EU) 2018/858. That delegated act shall also set the date of application of the obligation to have a minimum share of recycled content no later than 14 August 2033. Steel used as reinforcement materials in tyres shall not be considered to fall within the scope of that delegated act.
By 30 September 2028, the Commission shall adopt a delegated act, in accordance with Article 51, establishing the methodology for the calculation and verification of the share of steel recycled from post-consumer steel waste in vehicle types and, if applicable, from ferrous scrap, present in and incorporated into vehicle types.
8. By 30 September 2027, the Commission shall assess the feasibility of establishing a requirement on the minimum share of aluminium and its alloys, recycled from post-consumer waste present in and incorporated into vehicle types, considering in particular the following:
(a)
the current and forecast availability of aluminium and its alloys recycled from pre-consumer and post-consumer waste;
(b)
the current shares of recycled content from post-consumer waste in aluminium and its alloys in vehicles placed on the market;
(c)
economic viability, technical and scientific progress, including changes in the availability of recycling technologies concerning the type of materials recycled, and their recycling rates;
(d)
the contribution of a minimum share of recycled content of aluminium in vehicles to the Union’s open strategic autonomy, climate environmental and industrial objectives, in particular as regards the creation of complementary lead markets for decarbonised aluminium and its alloys;
(e)
the need to prevent disproportionate negative impacts on the affordability of vehicles containing aluminium and its alloys; and
(f)
the influence on the overall costs and competitiveness of the automotive sector.
By 30 September 2028 the Commission shall adopt a delegated act, in accordance with Article 51, to supplement this Regulation by establishing a minimum share of recycled aluminium and its alloys to be present in and incorporated into vehicle types to be type-approved in accordance with this Regulation and Regulation (EU) 2018/858. That delegated act shall also set the date of application of the obligation to have a minimum share of recycled content no later than 14 August 2033.
By 30 September 2028, the Commission shall adopt a delegated act, in accordance with Article 51, establishing the methodology for the calculation and verification of the share of aluminium and its alloys recycled from post-consumer waste in vehicle types and, if applicable from pre-consumer waste, present in and incorporated into vehicle types.
9. By 31 August 2029, the Commission shall assess the feasibility of establishing a requirement on the minimum share of:
(a)
magnesium and its alloys, recycled from pre-consumer and post-consumer waste and present in and incorporated into vehicle types; and
(b)
neodymium, dysprosium, praseodymium, terbium, samarium, nickel, cobalt or boron recycled from post-consumer waste and, where relevant, pre-consumer waste, present in and incorporated into permanent magnets.
The feasibility assessment shall take into account the following:
(a)
the current and forecast availability of the materials referred to in the first subparagraph, points (a) and (b), recycled from pre-consumer and post-consumer waste;
(b)
the current shares of recycled content from post-consumer waste in the materials referred to in the first subparagraph, points (a) and (b), in vehicles placed on the market;
(c)
economic viability, technical and scientific progress, including changes in the availability of recycling technologies concerning the type of materials recycled, and their recycling rates;
(d)
the contribution of a minimum share in vehicles of recycled content of the materials referred to in the first subparagraph, points (a) and (b), to the Union’s strategic autonomy and its climate and environmental objectives;
(e)
possible impacts on the functioning of vehicles from incorporating recycled content of the materials referred to in the first subparagraph, points (a) and (b), into vehicle parts and components;
(f)
the need to prevent disproportionate negative impacts on the affordability of vehicles containing the materials referred to in the first subparagraph, points (a) and (b);
(g)
the influence on the overall costs and competitiveness of the automotive sector.
After finalisation of the assessment referred to in the first subparagraph, the Commission is empowered to adopt a delegated act, in accordance with Article 51, to supplement this Regulation by establishing a minimum share of:
(a)
magnesium and its alloys, recycled from post-consumer waste and, where relevant, pre-consumer waste, present in and incorporated into vehicle types; and
(b)
neodymium, dysprosium, praseodymium, terbium, samarium, nickel, cobalt or boron recycled from post-consumer waste and, where relevant, pre-consumer waste, present in and incorporated into permanent magnets.
The delegated act referred to in the third subparagraph shall also set the date of application of the obligation to have a minimum share of recycled content.
By 30 September 2029, the Commission shall adopt a delegated act, in accordance with Article 51, establishing the methodology for the calculation and verification of the share of the recycled materials referred to in the third subparagraph present in and incorporated into vehicle types.
Design to enable removal and replacement of certain parts and components in vehicles
1. Each vehicle belonging to a new vehicle type that is type-approved as from 1 September 2032 under Regulation (EU) 2018/858 and Regulation (EU) No 168/2013 shall be designed in a way which does not hinder the removal by authorised treatment facilities of the parts and components listed in Part C of Annex VIII from the concerned vehicle during the waste phase of the vehicle with a view to replacement, reuse, recycling, remanufacturing or refurbishing where technically feasible.
2. Each vehicle belonging to a new vehicle type that is type-approved as from 1 September 2032 under Regulation (EU) 2018/858 shall be designed to enable, in a readily and non-destructive manner, the removal and replacement of electric vehicle batteries and their battery packs and e-drive motors from the vehicle by authorised treatment facilities or repair and maintenance operators during the use phase and waste phase of the vehicle.
3. The Commission is empowered to adopt delegated acts in accordance with Article 51 to amend paragraph 2 by including additional parts and components listed in Part C of Annex VIII, taking into account technical and scientific progress.
4. The Commission may adopt implementing acts laying down the conditions for the design for removal and replacement of parts and components referred to in paragraph 2 where necessary to ensure harmonised implementation of the obligation set out in that paragraph. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 52(2).
5. Manufacturers shall not hinder the removal and replacement of vehicle parts and components using software updates, unless otherwise provided for in Union law.
General obligations
1. Manufacturers shall demonstrate that new vehicle types that they have manufactured and that are placed on the market are type-approved in accordance with the requirements of Regulation (EU) 2018/858, Regulation (EU) No 168/2013 and this Regulation.
2. For the purposes of type-approval of vehicle types to which the requirements in Articles 4, 5, 6 or 7 apply, the manufacturer shall provide the documentation showing compliance with those requirements and shall:
(a)
include it in the information folder referred to in Article 24 of Regulation (EU) 2018/858 or in Article 27 of Regulation (EU) No 168/2013, as applicable; and
(b)
submit it to the type-approval authority in accordance with Article 23 of Regulation (EU) 2018/858 or in Article 26 of Regulation (EU) No 168/2013, as applicable.
3. For the purposes of type-approval of vehicles to which the requirements set out in Article 10 of this Regulation apply, the manufacturer shall draw up the information referred to in Article 10(1) of this Regulation and submit it, in accordance with Article 24(1), point (a), of Regulation (EU) 2018/858, to the type-approval authority together with the application for type-approval referred to in Article 23 of that Regulation.
4. For the purposes of type-approval of vehicles to which the requirements set out in Article 11 of this Regulation apply, the manufacturer shall submit the declaration confirming compliance with the requirement set out in Article 11(1) of this Regulation, in accordance with 24(1), point (a), of Regulation (EU) 2018/858, or with Article 27(1) of Regulation (EU) No 168/2013, as applicable, to the type-approval authority together with the application for type-approval.
Circularity strategy
1. Each manufacturer shall as from 1 September 2029 draw up a circularity strategy at manufacturer level.
2. The circularity strategy shall describe which actions the manufacturer will take to follow up on its obligations in order to ensure that the circularity requirements in Chapter II are met.
3. The circularity strategy shall contain the elements laid down in Part A of Annex V.
4. Each manufacturer shall provide the type-approval authorities of the Member States and the Commission with a copy of the circularity strategy within 30 days after it has been drawn up.
5. Each manufacturer shall monitor and follow up on the actions contained in the circularity strategy and update the strategy, indicating the relevant new changes of the circularity strategy, every five years in accordance with Part B of Annex V. The manufacturer shall provide an updated circularity strategy to the Commission.
6. The Commission shall make the circularity strategies and any updates to those strategies publicly available, except for confidential information.
7. By 31 August 2033 and at least every six years thereafter, the Commission shall draw up and publish a report on the circularity of the automotive sector. That report shall be based in particular on circularity strategies and updates to such strategies.
Declaration on recycled content present in vehicles
1. Manufacturers shall declare, for each new vehicle type that is type-approved under Regulation (EU) 2018/858 as from the first day of the month following 12 months from the adoption of the respective methodologies for the calculation and verification of the share of the materials recycled from post-consumer waste in vehicle types, as referred to in Article 6 of this Regulation, the respective share of recycled content of:
(a)
neodymium, dysprosium, praseodymium, terbium, samarium, nickel, cobalt and boron in permanent magnets in e-drive motors;
(b)
aluminium and its alloys;
(c)
magnesium and its alloys;
(d)
steel and its alloys;
(e)
plastics.
The declaration shall concern the recycled content of those materials present in the vehicle type and indicate, per material share, and for plastic components heavier than 100 grams, whether the material is recycled from pre-consumer waste or from post-consumer waste.
2. The type-approval authorities shall verify that the required documentation has been submitted by the manufacturers and that it contains the information referred to in paragraph 1.
3. By way of derogation from paragraph 1, the requirement to declare the share of recycled content of a certain material shall not apply where a target has become applicable for that material under Article 6.
Information on removal and replacement of parts, components and materials present in vehicles
1. From 1 September 2029, manufacturers shall, for new vehicle types that have been type-approved, provide waste management operators, publishers of technical information and repair and maintenance operators unrestricted, standardised and non-discriminatory access to the information listed in Annex VI, enabling access to, and safe removal and replacement of, the following, unless that information is available under other Union legislation:
(a)
electric vehicle batteries and their battery packs incorporated in the vehicle;
(b)
parts, components and materials which contain the fluids and liquids listed in Part B of Annex VIII and which are contained in vehicles;
(c)
parts and components listed in Part C of Annex VIII contained in vehicles;
(d)
parts and components which contain the critical raw materials as referred to in Article 28(1), point (b), of Regulation (EU) 2024/1252 at the time of the type-approval of the vehicle;
(e)
digitally coded components and parts in a vehicle, where such coding prevents their repair, maintenance or replacement in another vehicle.
Point (e) of the first subparagraph shall not apply to information to be provided to publishers of technical information.
2. Manufacturers shall make rescue and emergency response guidance information available to emergency services.
3. Manufacturers shall ensure cooperation with the authorised treatment facilities, publishers of technical information, retrofit operators, and repair and maintenance operators by establishing necessary communication platforms to provide and keep up-to-date the information referred to in paragraph 1 and the information specified in Annex VI.
The manufacturers shall provide the information referred to in the first subparagraph free of charge. The manufacturers may collect reasonable and proportionate charges from waste management operators, publishers of technical information and repair and maintenance operators to the extent necessary to cover the actual administrative costs incurred for making the required information accessible through communication platforms.
4. The Commission is empowered to adopt delegated acts in accordance with Article 51 to amend Annex VI by revising the list of parts, components and materials of vehicles and the scope of information to be provided by the manufacturers. The Commission shall take into account technical and regulatory developments, current information technology and foreseeable vehicle technology developments.
Labelling of parts, components and materials present in vehicles
1. Manufacturers and their suppliers shall use the nomenclature of the component and material coding standards listed in points 1, 2 and 3 of Annex VII for the labelling and identification of parts, components and materials of vehicles.
2. The Commission is empowered to adopt delegated acts in accordance with Article 51 to amend Annex VII in order to adapt it to technical and scientific progress.
Digital Circularity Vehicle Passport
1. From 1 September 2032, each vehicle placed on the market shall have a Digital Circularity Vehicle Passport, which shall be aligned, interoperable and, where possible, integrated with other vehicle related environmental passports established under Union law, in particular the passports referred to in Article 77 of Regulation (EU) 2023/1542, in Article 3, point (68), of Regulation (EU) 2024/1257 and with other relevant passports established pursuant to Regulation (EU) 2024/1781.
2. The Digital Circularity Vehicle Passport of a vehicle that is being placed on the market shall be accessible free of charge and shall contain, in digital format, the following:
(a)
the information referred to in Article 11;
(b)
the information about parts containing lead, mercury, cadmium or hexavalent chromium content of the vehicle as referred to in the derogation set out in Article 5(5);
(c)
the declaration on the share of recycled content of plastic and the materials listed in Article 10(1);
(d)
the official catalogue of spare parts for the vehicle type concerned.
3. Where information required under this Article is already accessible through a passport referred to in paragraph 1 other than the Digital Circularity Vehicle Passport, the information required under paragraph 2 shall not be duplicated in the Digital Circularity Vehicle Passport, provided that interoperability is ensured.
4. The manufacturer placing the vehicle on the market shall ensure that the information referred to in paragraph 2 is accurate, complete and up to date.
5. All information included in the Digital Circularity Vehicle Passport shall comply with the rules established by the Commission under paragraph 6 and shall be:
(a)
based on open standards;
(b)
developed with an interoperable format;
(c)
transferable through an open interoperable data exchange network without vendor lock-in;
(d)
machine-readable, structured and searchable.
6. By 14 August 2030, the Commission shall adopt implementing acts laying down rules on the following:
(a)
the manner and basic requirements of the technical solution to be used for accessing the Digital Circularity Vehicle Passport in a manner that does not preclude any technological solution;
(b)
the technical design and operation requirements for the Digital Circularity Vehicle Passport, including rules on:
(i)
the alignment and interoperability of the Digital Circularity Vehicle Passport with other passports required by Union legislation;
(ii)
the storage and processing of information included in the Digital Circularity Vehicle Passport;
(iii)
the availability of the Digital Circularity Vehicle Passport after the manufacturer responsible for the fulfilment of the obligations set out in paragraph 4 ceases to exist or ceases its activity in the Union;
(c)
the introduction, modification and updating of information included in the Digital Circularity Vehicle Passport by third parties other than the manufacturer;
(d)
the conditions for access to the Digital Circularity Vehicle Passport, including the right of access and the relevant rules for the protection of data and the protection of intellectual property rights;
(e)
the location of the data carrier or other identifier enabling access to the Digital Circularity Vehicle Passport of the vehicle.
When laying down the rules referred to in the first subparagraph, the Commission shall take into account the need to ensure a high level of security and privacy.
The implementing acts referred to in the first subparagraph shall be adopted in accordance with the examination procedure referred to in Article 52(2).
Competent authority for management of end-of-life vehicles
1. Member States shall designate one or more competent authorities to be responsible for the obligations under this Chapter, in particular for monitoring and verifying compliance of economic operators, producers and producer responsibility organisations with their obligations as set out in Articles 15 to 37 and Annex I.
2. Each Member State may designate one contact point, among the competent authorities referred to in the paragraph 1, for the purpose of communicating with the Commission.
3. Member States shall lay down the details of the competent authorities’ organisation and operation, including the administrative and procedural rules for:
(a)
the registration of producers in accordance with Article 19;
(b)
the authorisation of producers and producer responsibility organisations in accordance with Article 18;
(c)
the oversight of the implementation of extended producer responsibility obligations in accordance with Articles 16 and 20;
(d)
the collection of data on vehicles and end-of-life vehicles in accordance with Article 19(12) and Article 50(6);
(e)
making information available in accordance with Article 50.
4. By 30 June 2027, Member States shall notify the Commission of the names and addresses of the competent authorities designated pursuant to paragraph 1. Member States shall inform the Commission without undue delay of any changes to the names or addresses of those competent authorities.
Authorised treatment facilities
1. Without prejudice to Directive 2010/75/EU, any establishment or undertaking that intends to carry out treatment operations on end-of-life vehicles shall obtain a permit from the competent authority in accordance with Article 23 of Directive 2008/98/EC and shall comply with the conditions laid down in that permit.
2. In order to issue a permit referred to in paragraph 1 of this Article, the competent authority shall verify whether the establishment or the undertaking has the capacity that is necessary to comply with the obligations set out in Article 26.
3. Permits referred to in paragraph 1 of this Article shall indicate that the treatment facilities have the competence to issue a certificate of destruction, as referred to in Article 25.
By way of derogation from the first subparagraph of this paragraph, Member States may provide under their national legal frameworks that authorised treatment facilities are competent to issue the certificate of destruction referred to in Article 25.
4. Producers or, where appointed under Article 17(1), producer responsibility organisations may conclude contracts with authorised treatment facilities for the purpose of fulfilling their producer responsibility obligations. Such contracts shall be fair and transparent and shall not contain discriminatory terms or conditions.
Member States may provide a model contract to facilitate compliance with this Article.
5. Member States shall ensure that the conditions and the procedures for the granting of the permit are fully coordinated where more than one competent authority or more than one establishment or undertaking intending to carry out treatment operations on end-of-life vehicles is involved in those permit procedures, in order to guarantee an effective integrated approach by all the competent authorities.
6. The Commission is empowered to adopt an implementing act laying down detailed requirements applicable to the contracts referred to in paragraph 4 of this Article, with a view to ensuring fair, transparent and non-discriminatory terms and conditions. That implementing act shall be adopted in accordance with the examination procedure referred to in Article 52(2).
Extended producer responsibility
1. From 1 September 2029, producers shall have extended producer responsibility for vehicles that they make available on the market for the first time within the territory of a Member State, including where the vehicle has previously been made available on the market in a Member State other than the Member State within whose territory the vehicle is made available. The extended producer responsibility scheme shall be consistent with Articles 8 and 8a of Directive 2008/98/EC and shall comply with the requirements of this Chapter.
2. The extended producer responsibility shall include the obligation for producers to ensure that:
(a)
vehicles which they have made available on the market for the first time within the territory of a Member State and which become end-of-life vehicles are:
(i)
collected in accordance with Article 23;
(ii)
treated in accordance with Article 26;
(b)
the waste management operators treating end-of-life vehicles referred to in point (a) meet the targets laid down in Article 33.
3. In the outermost regions referred to in Article 349 TFEU, Member States may adapt the producers’ obligations referred to in paragraphs 1 and 2 of this Article in order to cover the costs of managing end-of-life vehicles and taking into account the characteristics of those regions.
4. In addition to the information referred to in Article 8a(3), point (e), of Directive 2008/98/EC, producers, in the case of individual fulfilment of extended producer responsibility obligations, or producer responsibility organisations appointed in the case of collective fulfilment of extended producer responsibility obligations, shall publish on their websites once a year, subject to commercial and industrial confidentiality, the information on the collection of end-of-life vehicles and the achievement of targets on reuse and recycling, reuse and recovery and plastic recycling by themselves in the case of individual fulfilment of extended producer responsibility obligations, or by the producers which appointed that producer responsibility organisation in the case of collective fulfilment of extended producer responsibility obligations.
Producer responsibility organisations
1. Producers may choose to fulfil their extended producer responsibility obligations either individually or may appoint a producer responsibility organisation authorised in accordance with Article 18 to fulfil the extended producer responsibility obligations on their behalf.
Member States may adopt measures to require that producers appoint a producer responsibility organisation to fulfil their extended responsibility obligations on their behalf.
2. Producer responsibility organisations shall ensure the confidentiality of the data in their possession as regards proprietary information or information directly attributable to individual producers or their authorised representatives for the extended producer responsibility.
3. In addition to the information referred to in Article 16(4), producer responsibility organisations shall make publicly available the information on the selection procedure applied in accordance with paragraph 5 of this Article.
4. Producer responsibility organisations shall ensure regular dialogue between stakeholders pursuant to Article 8a(6) of Directive 2008/98/EC. Waste management operators active in collection and treatment of end-of-life vehicles shall designate observer members to the executive boards of the producer responsibility organisations.
5. Waste management operators shall be subject to a non-discriminatory selection procedure, based on transparent award criteria, carried out by producers or producer responsibility organisations and which does not place a disproportionate burden on small and medium-sized enterprises.
Authorisation on fulfilment of extended producer responsibility
1. A producer, in the case of individual fulfilment of extended producer responsibility obligations, and producer responsibility organisations appointed in the case of collective fulfilment of extended producer responsibility obligations, shall apply for an authorisation from the competent authority.
2. The authorisation shall be granted only where it is demonstrated that the requirements laid down in Article 8a(3), points (a) to (d), of Directive 2008/98/EC are complied with and the measures put in place by the producer or producer responsibility organisation are sufficient to meet the obligations set out in this Chapter with regard to the number of vehicles made available on the market for the first time within the territory of a Member State by the producer or producers on whose behalf the producer responsibility organisation acts.
Producers, in the case of individual fulfilment of extended producer responsibility obligations, and producer responsibility organisations, in the case of collective fulfilment of extended producer responsibility obligations, may only be registered if they hold an authorisation from the competent authority in accordance with this Article. This is without prejudice to the possibility of combining the registration procedure pursuant to Article 19 and the authorisation procedure pursuant to this Article into a single procedure.
3. Member States shall, in their measures laying down administrative and procedural rules referred to in Article 14(3), point (b), include the details of the authorisation procedure, which may differ according to whether it relates to individual or collective fulfilment of the extended producer responsibility obligations, and the modalities for verifying compliance of producers and producer responsibility organisations, including the information to be provided by producers or producers responsibility organisations to that end.
4. The producer or the producer responsibility organisation shall notify the competent authority without undue delay of any changes to the information contained in the authorisation, of any changes that concern the terms of the authorisation or of the permanent cessation of operations.
5. The self-control mechanism provided for in Article 8a(3), point (d), of Directive 2008/98/EC shall be carried out regularly, and at least every three years, and upon the request by the competent authority, in order to verify that the provisions in that point are complied with and the conditions for authorisation referred to in paragraph 2 of this Article continue to be met. The producer or the producer responsibility organisation shall, upon request, present a self-control report and, where necessary, the draft corrective action plan to the competent authority. Without prejudice to the competencies under paragraph 6 of this Article, the competent authority may make observations on the self-control report and on the draft corrective action plan, and shall communicate any such observations to the producer or the producer responsibility organisation. The producer or producer responsibility organisation shall draw up and implement the corrective action plan based on those observations.
6. The competent authority may decide to revoke the authorisation if the producer or producer responsibility organisation no longer fulfils the requirements with regard to the organisation of the collection and treatment of end-of-life, fails in relation to reporting to the competent authority, fails to notify the competent authority of any changes that concern the terms of the authorisation, or has ceased operations.
Registration
1. By 31 August 2029, each Member State shall establish a register of producers, or use an existing register of producers, which shall serve to monitor compliance of producers with the requirements of this Chapter.
The register shall provide links to other national registers of producers’ websites to facilitate, in all Member States, registration of producers or authorised representatives for the extended producer responsibility and, if available, to the national websites containing information on the registration procedure.
By 31 August 2029, the Commission shall establish a website which contains the links to all national registers of producers to facilitate registration in all Member States.
Member States shall inform the Commission about the links to their national registers of producers within 30 days of the launch of those registers.
2. Producers shall register in the national register referred to in paragraph 1. They shall to that end submit an application for registration in each Member State where they make a vehicle available on the market for the first time.
Producers shall submit the application for registration via an electronic data-processing system as referred to in paragraph 8, point (a).
Producers shall only make available vehicles on the market of a Member State if they or, in case of authorisation, their authorised representatives for the extended producer responsibility, are registered in such Member State.
3. The application for registration shall include the information listed in Annex IX. Member States may request additional information or documents, as necessary, to use the register of producers in an efficient manner.
4. By way of derogation from paragraph 3 of this Article, the information referred to in point 1(d) of Annex IX shall be provided either in the application for registration under paragraph 3 of this Article or in the application for authorisation under Article 18.
5. Where a producer has appointed a producer responsibility organisation in accordance with Article 17(1), the obligations under this Article shall be met by that organisation mutatis mutandis unless otherwise specified by the Member State in which the vehicle has been made available on the market for the first time.
6. The obligations under this Article may be fulfilled on a producer’s behalf by an authorised representative for the extended producer responsibility.
If more than one producer is represented in a Member State by one authorised representative, that authorised representative shall provide the name and the contact details for each of the represented producers separately.
7. Member States may decide that the registration procedure pursuant to this Article and the authorisation procedure pursuant to Article 18 constitute a single procedure, provided that the application for authorisation meets the requirements set out in paragraphs 3 to 6 of this Article.
8. The competent authority shall:
(a)
make available on its website information about the application process via an electronic data-processing system;
(b)
grant registrations and provide a registration number within a maximum period of 12 weeks from the moment that all the information required pursuant to paragraphs 2 and 3 is provided.
9. The competent authority may:
(a)
lay down modalities with regard to the requirements and process of registration without adding substantive requirements to those laid down pursuant to paragraphs 2 and 3;
(b)
charge cost-based and proportionate fees to producers for the processing of the applications referred to in paragraph 2 of this Article and in Article 18(1).
10. The competent authority may refuse to register a producer or withdraw the producer’s registration where the information referred to in paragraph 3 of this Article and related documentary evidence are not provided or are not sufficient, or where the producer no longer meets the requirements laid down in point 1(d) of Annex IX.
The competent authority shall withdraw the producer’s registration if the producer has ceased to exist.
11. The producer, or, where applicable, the producer’s authorised representative for the extended producer responsibility or the producer responsibility organisation appointed on behalf of the producers it represents shall without undue delay notify the competent authority of any changes to the information contained in the registration and of any permanent cessation as regards the making available on the market within the territory of the Member State of the vehicles referred to in the registration.
12. The producer or, where applicable, the producer’s authorised representative for the extended producer responsibility or the producer responsibility organisation shall report to the competent authority responsible for the register on the performance of extended producer responsibility obligations.
Where the information in the register of producers is not publicly accessible, Member States shall ensure that providers of online platforms allowing consumers to conclude distance contracts with producers are granted access, free of charge, to that information.
Financial responsibility of producers
1. The financial contributions paid by the producer shall cover the following costs related to the vehicles that the producer makes available on the market for the first time within the territory of a Member State:
(a)
the costs of the collection of end-of-life vehicles that are necessary to meet the requirements in Articles 23 to 25 and of their subsequent transport in an efficient manner and the costs of the treatment of end-of-life vehicles that are necessary to meet the requirements in Articles 26 to 30, 33 and 35, taking into account the revenues of waste management operators linked to the sales of used spare parts and used spare components, of depolluted end-of-life vehicles, or of secondary raw materials recovered from such parts, components and materials; those costs shall be based on an average cost calculation;
(b)
the costs of conducting awareness raising campaigns aimed to inform the public and to improve collection of end-of-life vehicles;
(c)
the costs of establishing the notification system referred to in Article 25;
(d)
the administrative costs of gathering and making data available and reporting to the competent authorities.
For vehicles falling within the scope of Directive 2000/53/EC that have been made available on the market before 13 August 2026, and by way of derogation from the first subparagraph, point (a), and paragraph 2 of this Article, in Member States where, in accordance with Article 5(4), second subparagraph, of Directive 2000/53/EC, the producers did not have to meet all but only a significant part of the costs, the financial contributions that the producer of those vehicles has to make shall correspond to a level constituting a significant part of the costs referred to therein.
2. The financial contributions paid by the producers which make available on the market for the first time within the territory of a Member State the vehicle shall also cover costs referred to in paragraph 1, point (a), related to vehicles for which the producer cannot be identified or ceased to exist in the Member State where the vehicle became an end-of-life vehicle, in proportion to their respective share of the market.
3. The financial contributions paid by the producers making available on the market special purpose vehicles shall cover only the costs referred to in paragraph 1, point (a), that concern collection and depollution of such vehicles.
4. In the case of individual fulfilment of extended producer responsibility obligations, the producers shall provide a guarantee for vehicles that they make available on the market for the first time in the territory of a Member State. That guarantee shall ensure that the operations referred to in paragraph 1 relating to those vehicles will be financed, including in the event of permanent cessation of their operations or insolvency.
The amount of the guarantee shall be determined by the Member States in which the vehicle has been made available on the market for the first time taking into account criteria laid down in Article 21.
The guarantee may take the form of participation by the producer in appropriate schemes for the financing of the management of end-of-life vehicles, a financial guarantee or equivalent insurance.
5. When a new vehicle has been type-approved in a multi-stage type-approval, the producer of the base vehicle shall be considered to be the producer of the completed vehicle and may collect pro rata contributions from the manufacturers of the parts, other than the base vehicle, that have been type approved in the multi-stage type-approval. Those pro rata contributions shall only cover costs in relation to depollution in accordance with Article 28 and removal of parts and components in accordance with Article 29.
Microenterprises, as defined in Article 2(3) of the Annex to Commission Recommendation 2003/361/EC ( 39 ) , shall be exempted from such contributions.
6. The competent authority shall, in close cooperation with producers, producer responsibility organisations and waste management operators, monitor:
(a)
the average costs of collection, recycling and treatment operations and the revenues of waste management operators;
(b)
the level of financial contributions to be paid by the producers to the producer responsibility organisations appointed in the case of collective fulfilment of extended producer responsibility obligations so that the costs are fairly allocated between all interested operators.
Fee modulation
1. In the case of a collective fulfilment of extended producer responsibility obligations, producer responsibility organisations shall ensure that the financial contributions paid to them by producers are modulated by taking into account at least the following:
(a)
the weight of the vehicle, excluding electric vehicle batteries;
(b)
the rate of recyclability and reusability of the vehicle type to which the vehicle belongs, based on the information submitted to the type-approval authority in accordance with Article 4;
(c)
the time needed to dismantle the vehicle at an authorised treatment facility, especially for parts and components which need to be removed prior to shredding under Article 29;
(d)
the share of materials and substances preventing a high-quality recycling process;
(e)
the percentage of recycled content of materials listed in Articles 6 and 10 used in the vehicle;
(f)
the presence and amount of substances referred to in Article 5(4).
2. The Commission is empowered to adopt delegated acts in accordance with Article 51 supplementing this Regulation by establishing detailed rules on how the criteria provided for in paragraph 1 of this Article are to be applied.
Cost allocation mechanism for vehicles becoming end-of-life vehicles in another Member State
1. Notwithstanding Article 16 and Article 20(2), where a vehicle in the category M 1 or N 1 becomes an end-of-life vehicle in a Member State other than the Member State within whose territory the vehicle was placed on the market, and no producer can be identified on the territory of the Member State where it becomes an end-of-life vehicle, the manufacturer of that vehicle shall ensure that the costs of waste management operations referred to in Article 20(1), points (a) and (d), incurred by waste management operators are covered.
2. In order to fulfil its obligations under paragraph 1, a manufacturer shall:
(a)
designate by a written mandate an authorised representative for the cross-border mechanism in each Member State and notify the competent authorities about the designations; and
(b)
establish cross-border cooperation mechanisms with the waste management operators carrying out waste management operations referred to in Article 20(1), points (a) and (d).
The manufacturer’s authorised representative referred to in point (a) of the first subparagraph of this paragraph shall perform the tasks specified in the mandate received from the manufacturer. A manufacturer may designate a producer responsibility organisation to act as its authorised representative.
Where the manufacturer is established outside of the Union, the manufacturer’s representative in the Union appointed in application of Article 13(4) of Regulation (EU) 2018/858 may fulfil the manufacturer’s obligations under points (a) and (b) of the first subparagraph of this paragraph.
3. Manufacturers shall demonstrate compliance with the requirements set out in paragraph 2 to their producers.
4. Producers shall make available on the market of a Member State only those vehicles from manufacturers who have demonstrated compliance with the requirements set out in paragraph 2.
5. The Member State where the vehicle became an end-of-life vehicle shall monitor manufacturers’ and their authorised representatives’ compliance with paragraphs 1 and 2 of this Article. The monitoring shall be based on the information reported and verified by manufacturers and their authorised representatives to the competent authorities on the implementation of paragraphs 1 and 2 of this Article, in particular on the calculation and allocation of costs for the management of end-of-life vehicles referred to in paragraph 1 of this Article, with due regard for business confidentiality and other concerns regarding competitiveness.
6. Where necessary to ensure compliance with this Article and taking into account information provided by the Member States pursuant to the cooperation and monitoring activities referred to in paragraphs 2 and 5 of this Article, the Commission is empowered to adopt delegated acts in accordance with Article 51 this Regulation. Such acts shall aim, in particular, to avoid a distortion of the single market and to ensure a level playing field for economic operators established within and outside the Union. The delegated acts may lay down detailed rules on the obligations of the manufacturers, in particular those established outside of the Union, the manufacturers’ authorised representatives, producers, Member States and waste management operators and the features of the mechanisms referred to in this Article.
Collection of end-of-life vehicles
1. Producers shall ensure that all vehicles that they have made available on the market for the first time in the territory of a Member State are collected when those vehicles become end-of-life vehicles.
2. For the purpose of paragraph 1, the producers or, where appointed in accordance with Article 17(1), the producer responsibility organisations shall set up, or participate in the setting up of, collection systems, including collection points.
Member States shall adopt the necessary measures to ensure that producers or, where appointed in accordance with Article 17(1), producer responsibility organisations set up collection systems for all end-of-life vehicles.
3. The producers or, where appointed in accordance with Article 17(1), the producer responsibility organisations shall ensure that collection systems referred to in paragraph 2 of this Article:
(a)
cover the whole territory of the Member State;
(b)
are provided with adequate availability of authorised treatment facilities or collection points, taking into account population size and density, expected volume of end-of-life vehicles, not being limited to areas where the collection and subsequent management is most profitable;
(c)
ensure collection of waste parts from repairs of vehicles;
(d)
enable collection of end-of-life vehicles, irrespective of their origin;
(e)
enable the delivery of all end-of-life vehicles free of charge to collection points or authorised treatment facilities as provided in Article 24(2).
4. Producers or, where appointed in accordance with Article 17(1), producer responsibility organisations shall publish and regularly update the list of collection points and authorised treatment facilities on their websites and carry out educational campaigns promoting the collection systems for end-of-life vehicles and informing about environmental consequences of improper collection and handling of end-of-life vehicles. Member States may require that the educational campaigns be coordinated within the Member State, in collaboration with both the producers or, where appointed in accordance with Article 17(1), producer responsibility organisations and the competent authorities.
5. Member States may authorise collection points other than authorised treatment facilities to collect end-of-life vehicles.
The collection points shall obtain a permit from the competent authority in accordance with Article 23 of Directive 2008/98/EC and shall comply with the conditions laid down in that permit. In order to issue a permit, the competent authority shall verify that such establishment or undertaking has the capacity necessary to carry out the following obligations:
(a)
collect end-of-life vehicles and temporarily store them in accordance with Part A of Annex VIII;
(b)
prepare for the transfer of the collected end-of-life vehicles to authorised treatment facilities by preventing the accidental leakage of fluids and unauthorised access to the collection point;
(c)
guarantee that all collected end-of-life vehicles are transferred to an authorised treatment facility within two months of their receipt.
6. The collection points shall issue a document in electronic format, confirming receipt of the end-of-life vehicle, to the vehicle owner, and provide it through an electronic notification procedure established in accordance with Article 25(2) to the relevant authorities of the Member State, including the competent authorities designated under Article 14.
Delivery of end-of-life vehicles
1. A vehicle owner, and any economic operator acting on behalf of the vehicle owner, of a vehicle that becomes an end-of-life vehicle shall deliver it to an authorised treatment facility or to a collection point without undue delay. That obligation shall not apply to motor caravans, as referred to in Part A, point 5.1, of Annex I to Regulation (EU) 2018/858, that have become end-of-life vehicles as long as those vehicles are used for housing purposes.
All end-of-life vehicles for which no owner can be identified shall be delivered for treatment to authorised treatment facilities.
2. Delivery of an end-of-life vehicle to an authorised treatment facility or a collection point shall be free of charge for the last owner of a vehicle unless the end-of-life vehicle lacks any of the essential vehicle parts or components or contains waste which has been added to the end-of-life vehicle.
3. Essential parts for the purposes of this Article are in particular:
(a)
e-drive motors;
(b)
electric vehicle batteries;
(c)
engines;
(d)
multiple large pieces of bodywork.
4. Where the electric vehicle battery is missing from an end-of-life vehicle, the delivery of the end-of-life vehicle shall remain free of charge if the last owner of the vehicle provides documentation which proves that the electric vehicle battery has been handled by a professional operator in accordance with Regulation (EU) 2023/1542.
5. In the case of vehicles that have been declared as technical total losses by insurance companies, delivery of such end-of-life vehicles shall be free of charge notwithstanding that the essential parts set out in paragraph 2 are missing.
Certificate of destruction
1. Authorised treatment facilities shall issue a certificate of destruction to the last vehicle owner upon delivery of the end-of-life vehicle to the authorised treatment facility. The certificate of destruction shall be issued in accordance with the template set out in Annex X.
2. The certificate of destruction shall be issued in an electronic format and provided through an electronic notification procedure to the relevant authorities of the Member State, including the competent authorities designated under Article 14. The authorised treatment facility shall provide a copy of the electronic notification to the last vehicle owner and any economic operator acting on behalf of the vehicle owner.
3. Where the end-of-life vehicle, for which a certificate of destruction has been issued in a Member State, is registered in another Member State, the relevant authorities designated by the Member State where the certificate of destruction was issued shall inform the relevant authorities designated by the Member State where the vehicle is registered that a certificate of destruction has been issued for the vehicle in question.
4. The relevant vehicle registration authorities shall cancel the registration of an end-of-life vehicle only after receiving the certificate of destruction for that vehicle.
5. Certificates of destruction issued in a Member State shall be recognised in all other Member States.
Obligations for authorised treatment facilities
1. Authorised treatment facilities shall ensure that all end-of-life vehicles and their parts, components and materials, as well as waste parts from repairs of vehicles, are accepted and treated in compliance with the conditions set out in their permits, as well as in accordance with this Regulation. The treatment of the end-of-life vehicles may be carried out individually by one authorised treatment facility or, except for depollution, in cooperation with other authorised treatment facilities.
2. Authorised treatment facilities shall:
(a)
store, even temporarily, all end-of-life vehicles and their parts, components and materials in compliance with the minimum requirements set out in Part A of Annex VIII;
(b)
depollute all end-of-life vehicles, in compliance with Article 28 and the minimum requirements set out in Part B of Annex VIII;
(c)
remove the parts and components listed in Part C of Annex VIII from the end-of-life vehicle in compliance with Articles 29 and 30;
(d)
treat all end-of-life vehicles and their parts, components and materials in accordance with Articles 27 to 31, 33, 34 and 35 of this Regulation and Annex VIII thereto, the waste hierarchy and the general requirements laid down in Article 4 of Directive 2008/98/EC;
(e)
apply the best available techniques as defined in Article 3, point (10), of Directive 2010/75/EU, where applicable;
(f)
treat the received end-of-life vehicle within 12 months of the delivery date.
In addition to the requirements set out in Article 35 of Directive 2008/98/EC, the authorised treatment facilities shall electronically store the record of all the treatment operations performed, referred to in points (a) to (e) of the first subparagraph of this paragraph, of end-of-life vehicles for three years, and be able to present this information, upon request by relevant national authorities.
3. The Commission is empowered to adopt delegated acts in accordance with Article 51 to amend Annex VIII by adapting the minimum treatment requirements for end-of-life vehicles to scientific and technical progress in treatment technologies, including:
(a)
adding, deleting or revising the parts and components listed in Part C of Annex VIII;
(b)
revising the target values for the output fractions listed in Part G, point 2, of Annex VIII;
(c)
expanding the list of aluminium alloy types listed in Part G, points 2(b) and (c), of Annex VIII;
(d)
adding quality requirements to enhance the separation of recyclable plastics and target values for subsequent recycling technologies applicable to Part G, point 2, of Annex VIII.
4. Member States shall encourage authorised treatment facilities to introduce certified environmental management systems and to have audits conducted in accordance with Regulation (EC) No 1221/2009.
General requirements for shredding
1. From 1 September 2029, authorised treatment facilities and other waste management operators carrying out shredding operations shall request that end-of-life vehicles delivered to them for shredding, or large structural parts and components from the chassis or bodywork from end-of-life vehicles of categories N 2 , N 3 , M 2 , M 3 and O delivered to them for shredding or cutting are:
(a)
depolluted in accordance with Article 28 and their parts and components removed in accordance with Article 29; and
(b)
accompanied by a copy of the certificate of destruction that has been issued for the end-of-life vehicle concerned.
2. Authorised treatment facilities and waste management operators carrying out shredding operations and receiving end-of-life vehicles which do not comply with the requirements set out in paragraph 1 shall:
(a)
report the non-compliance to the competent authority, including the name and contact details of the natural or legal person who delivered the end-of-life vehicle to the authorised treatment facility or other waste management operator for shredding;
(b)
refrain from using those end-of-life vehicles in their shredding operations unless the competent authority authorises such operations or until the necessary steps to treat the end-of-life vehicle in accordance with Articles 28 and 29 and to issue a certificate of destruction in accordance with Article 25 have been taken.
3. Authorised treatment facilities and waste management operators conducting shredding of end-of-life vehicles shall only be allowed to mix end-of-life vehicles, their parts, components and materials with other waste, including packaging waste and waste electrical and electronic equipment, if the criteria and limit values of Part G, points 1 and 2, of Annex VIII are met.
Depollution of end-of-life vehicles
1. Within 30 days of delivery of an end-of-life vehicle to the authorised treatment facility, that facility shall depollute that vehicle before it is further treated, in compliance with the minimum requirements set out in Part B of Annex VIII.
2. The fluids and liquids listed in Part B of Annex VIII shall be separately collected and stored, in accordance with the requirements set out in Part A of Annex VIII. Waste oils shall be collected and stored separately from the other fluids and liquids and be treated in accordance with Article 21 of Directive 2008/98/EC.
3. The parts, components and materials containing substances referred to in Article 5(4) of this Regulation shall be removed from the end-of-life vehicles, and handled in accordance with Article 17 of Directive 2008/98/EC.
4. The batteries shall be separately removed from end-of-life vehicles and stored in a designated area for further treatment in accordance with Article 70(3) of Regulation (EU) 2023/1542.
5. The parts, components and materials, that have been depolluted, shall be handled and labelled in accordance with Articles 18 and 19 of Directive 2008/98/EC.
6. The authorised treatment facility shall document the depollution of end-of-life vehicles, by recording the information listed in Part B, point 4, of Annex VIII and report that information for each calendar year to the competent authority of the Member State.
Mandatory removal of parts and components for reuse, remanufacturing, refurbishment and recycling prior to shredding
1. From 1 September 2029, authorised treatment facilities shall ensure that the parts and components listed in Part C of Annex VIII, are removed from an end-of-life vehicle, prior to shredding or compacting, after the depollution operations referred to in Article 28 have been completed.
Authorised treatment facilities shall remove parts and components listed in Part C of Annex VIII with a reuse, remanufacturing or refurbishment potential in a non-destructive manner.
The second subparagraph of this paragraph shall not apply if an authorised treatment facility demonstrates that the manual dismantling, semi-automated or automated disassembly in a non-destructive way of parts and components listed in Part C of Annex VIII entails disproportionate economic costs that cannot be compensated by the revenues expected from the reuse, remanufacturing or refurbishment of those parts and components.
2. An authorised treatment facility shall not be required to remove parts and components listed in Part C of Annex VIII, with the exception of those that are to be removed in a non-destructive manner in accordance with paragraph 1 of this Article, if it demonstrates that post-shredder technologies separate materials from parts and components designated in the second column of Part C of Annex VIII as efficiently as manual dismantling processes, semi-automated or automated disassembly processes and that the criteria and limit values of Part G, points 1 and 2, of Annex VIII are met.
For the purposes of the first subparagraph, the authorised treatment facility shall provide the information listed in Part G, point 3, of Annex VIII.
3. In addition to the obligations set out in Article 35 of Directive 2008/98/EC, the authorised treatment facilities shall maintain records of the end-of-life vehicles that are processed without the prior removal of parts, components and materials in accordance with paragraph 2 of this Article, including the name and address of the treatment facilities, and the VIN of the end-of-life vehicles concerned.
The authorised treatment facilities shall provide the information in the records referred to in the first subparagraph of this paragraph to the competent authority in accordance with Article 50(6).
Requirements concerning the removed parts and components
1. All parts and components that have been removed from an end-of-life vehicle pursuant to Article 29(1) shall be assessed to determine whether they are fit for:
(a)
reuse, in accordance with Part D, point 1(a), of Annex VIII;
(b)
remanufacturing or refurbishment, in accordance with Part D, point 1(b), of Annex VIII;
(c)
recycling; or
(d)
other treatment operations, taking into account the specific treatment requirements in Part F of Annex VIII.
The assessment shall be carried out taking into account in particular the technical feasibility of conducting the processes referred to in the first subparagraph and vehicle safety requirements.
2. The removed parts and components fit for reuse, remanufacturing or refurbishment shall be:
(a)
labelled in compliance with Part D, point 2, of Annex VIII; and
(b)
protected appropriately against damage during transportation, loading and unloading.
3. The parts and components listed in Part E of Annex VIII shall not be reused unless the assessment referred to in paragraph 1 confirms that the use of those parts and components complies with the applicable vehicle requirements as set out in Regulations (EU) 2018/858 and (EU) No 168/2013. Those parts and components may only be transferred to another economic operator for reuse if they are to be installed by a qualified repair and maintenance operator.
4. The parts and components from end-of-life vehicles or repair and maintenance operations that are assessed as fit for reuse, remanufacturing or refurbishment shall not be considered waste. Authorised treatment facilities shall make available, upon request, to the relevant national authorities:
(a)
documentation confirming the assessment referred to in paragraph 1 demonstrating that the parts and components are fit for the purposes of reuse, remanufacturing or refurbishment; and
(b)
a copy of the invoice or contract related to the transfer of those parts and components.
5. This Article shall not apply to batteries to which Regulation (EU) 2023/1542 applies.
6. Authorised treatment facilities shall ensure that removed parts and components, which are not fit for reuse, remanufacturing or refurbishment, are sent for treatment in accordance with paragraph 1, first subparagraph, points (c) and (d).
Trade of used, remanufactured or refurbished parts and components
1. From 1 September 2029, any economic operator selling used, remanufactured or refurbished spare parts and components shall ensure that parts and components contain the labelling placed by authorised treatment facilities in accordance with Article 30(2), point (a).
2. In the case of sale of used, remanufactured or refurbished parts and components to consumers, the economic operators shall ensure that those parts and components are able to maintain their required functions and performance through normal use and comply with other requirements applicable to the goods sold in accordance with Directive (EU) 2019/771.
3. The requirements on economic operators in paragraphs 1 and 2 shall apply irrespective of the trading technique used, including online sales.
Reuse, remanufacturing and refurbishment of parts and components
1. From 1 September 2029, Member States shall incentivise the reuse, remanufacturing, retrofitting and refurbishment of parts and components, whether removed during the use or end-of-life phase of a vehicle.
The incentives referred to in the first subparagraph may include:
(a)
a requirement for maintenance and repair operators to offer customers to repair a vehicle with used, remanufactured or refurbished spare parts and components alongside the offer to repair the vehicle with new parts and components, provided that such a requirement is formulated not to create excessive costs or administrative burdens for micro- and small enterprises;
(b)
economic incentives designed to stimulate the market for used, remanufactured or refurbished spare parts and components.
2. Member States shall include in the waste prevention programmes required pursuant to Article 29 of Directive 2008/98/EC the incentives referred to in paragraph 1 of this Article.
3. The Commission shall facilitate the exchange of information and sharing of best practices among Member States on the incentives referred to in paragraph 1.
The Commission shall monitor the effectiveness of the incentives given by Member States.
Reuse, recycling and recovery targets
1. From 1 January 2030, Member States shall adopt the necessary measures to ensure that the producers or, where appointed in accordance with Article 17(1), producer responsibility organisations ensure that waste management operators achieve the following targets:
(a)
the reuse and recovery, as calculated together, is a minimum of 95 %, by average weight per vehicle, excluding batteries, and year;
(b)
the reuse and recycling, as calculated together, is a minimum of 85 %, by average weight per vehicle, excluding batteries, and year.
2. From 1 January 2032, Member States shall adopt the necessary measures to ensure that producers or, where appointed in accordance with Article 17(1), producer responsibility organisations ensure that a yearly target for the recycling of plastics of at least 30 % of the total average weight of plastics contained in the end-of-life vehicles is met by the waste management operators.
The weight of the plastic recycled and the total weight of plastics referred to in the first subparagraph shall exclude elastomers, thermosets other than polyurethane foams used for cushioning, and plastics that contain or are contaminated by any substance referred to in Article 7 of Regulation (EU) 2019/1021 when the thresholds of Annex IV to that Regulation are exceeded.
Ban on landfilling of non-inert waste
From 1 September 2029, the shredder heavy and shredder light fractions from end-of-life vehicles remaining after treatment containing non-inert waste shall not be accepted in a landfill if they exceed the limit values set out in Part G, points 2(d) and 2(e), of Annex VIII.
Shipments of end-of-life vehicles
1. Treatment of end-of-life vehicles may be undertaken outside the Member State concerned or outside the Union, provided that the shipment of end-of-life vehicles or waste produced in the process of their treatment is in compliance with Regulation (EU) 2024/1157.
2. Shipments of end-of-life vehicles from the Union to a third country in accordance with paragraph 1 of this Article shall only count towards the fulfilment of obligations and targets set out in Article 33 if the exporter of the end-of-life vehicles provides documentary evidence approved by the competent authority of destination demonstrating that the treatment took place in conditions that are considered equivalent to the requirements laid down in this Regulation and to environmental and human health protection requirements laid down in other Union legislation.
Transfer of ownership of used vehicles within the Union
1. For the purpose of transferring ownership of a used vehicle within the Union, an economic operator shall present to any natural or legal person interested in acquiring ownership of the vehicle concerned the documentation demonstrating that it is not an end-of-life vehicle, irrespective of the trading technique used, including by means of dedicated auctions for economic operators, distance contracts or online platforms. That documentation shall demonstrate that it is a roadworthy vehicle or shall consist of an assessment in accordance with Annex I proving that it is not an end-of-life vehicle.
2. For the purpose of transferring ownership of a used vehicle within the Union, natural persons who are not economic operators shall only be required to provide the documentation referred to in paragraph 1 where:
(a)
the vehicle is declared a total economic loss by an insurance company;
(b)
the sale is concluded entirely by means of an online platform, without physical handover of the vehicle between the seller and the buyer or any person acting on their behalf.
Status of the vehicle
1. When assessing damage to a vehicle involved in an accident, the insurance company or any other automotive expert carrying out the assessment on its behalf shall also assess whether the vehicle is an end-of-life vehicle in accordance with Annex I.
2. The competent authorities may require a vehicle owner, where there is doubt that a used vehicle is an end-of-life vehicle, to present documentation that the vehicle concerned is not an end-of-life vehicle. That documentation shall consist of an assessment in accordance with Annex I or a valid roadworthiness certificate.
3. The Commission is empowered to adopt delegated acts, in accordance with Article 51 of this Regulation, to amend this Regulation by removing the criteria listed in Annex I to determine whether a used vehicle is an end-of-life vehicle, provided that technological progress in the area of traceability, repairability and safety justifies limiting the instances where the vehicle shall be considered an end-of-life vehicle.
Competent authority for export of used vehicles to third countries
1. Member States shall designate one or more competent authorities responsible for the obligations laid down in this Chapter.
2. By 30 September 2027, Member States shall notify the Commission of the names and addresses of the competent authorities designated pursuant to paragraph 1. Member States shall inform the Commission without undue delay of any changes to the names or addresses of those competent authorities.
Controls and requirements on the export of used vehicles
1. From 1 September 2031, used vehicles to be exported shall be subject to the controls and requirements laid down in this Chapter.
2. This Chapter is without prejudice to other provisions of this Regulation as well as to other Union legal acts governing the release for export of goods, in particular Regulation (EU) No 952/2013 and its Articles 46, 47, 267 and 269.
3. Used vehicles may be exported only if they are:
(a)
not end-of-life vehicles; and
(b)
roadworthy at the date of lodging the export declaration, unless they have been recognised as vehicles of special cultural interest in accordance with Article 2(2), point (f), and Annex II.
4. The following information shall be provided or made available to customs authorities for each used vehicle to be exported:
(a)
the VIN of the used vehicle and the identification of the Member State where the vehicle was last registered;
(b)
a statement confirming that the used vehicle fulfils the requirements set out in paragraph 3 of this Article, or a certificate is provided as referred to in Annex II.
5. In order to verify compliance with this Chapter on allowing a used vehicle to be released for export:
(a)
until the interconnection referred to in Article 46(4) is operational, customs authorities shall exchange information and cooperate with competent authorities in accordance with Article 45, and, where necessary, shall take into account such exchange of information and cooperation in order to allow a used vehicle to be released for export;
(b)
once the interconnection referred to in Article 46(4) is operational, Article 40, Article 41(2) and (3) and Article 43(3) shall apply, and notifications and other exchanges under Articles 42, 43 and 44 shall take place by means of those electronic systems.
6. A used vehicle to be exported shall not be subject:
(a)
to an entry in the declarant’s records pursuant to Article 182 of Regulation (EU) No 952/2013;
(b)
to self-assessment pursuant to Article 185 of Regulation (EU) No 952/2013.
Automated verification of the information on vehicle status
1. Before releasing a used vehicle for export, customs authorities shall verify electronically and automatically via the electronic systems referred to in Article 46(4) if, based on the VIN and the information on the Member State of last registration, the vehicle is roadworthy. That obligation shall not apply with respect to vehicles which have been recognised as vehicles of special cultural interest in accordance with Article 2(2), point (f), and Annex II.
2. Where the information provided or made available to customs authorities does not correspond to the information in the national vehicle registers and national electronic systems on roadworthiness pursuant to paragraph 1, customs authorities shall not release that vehicle for export and shall inform the natural or legal person concerned thereof through those systems.
Risk management and customs controls
1. For the purpose of enforcing the provisions laid down in Article 39, customs authorities shall carry out controls on used vehicles to be exported in accordance with the provisions on risk management and customs controls laid down under Regulation (EU) No 952/2013. Without prejudice to Article 40 of this Regulation, such controls shall primarily be based on risk analysis, as established in Regulation (EU) No 952/2013.
2. In addition to the risk management referred to in paragraph 1 of this Article, once the interconnection referred to in Article 46 is operational, the electronic systems referred to in Article 46(1) shall contain the information and the customs authorities shall automatically and electronically verify through the interconnection referred to in Article 46(4) whether a used vehicle to be exported complies with specific conditions linked to the protection of the environment or road safety in accordance with paragraph 3 of this Article.
3. The Commission is empowered to adopt delegated acts in accordance with Article 51 to supplement this Regulation by setting out the compliance conditions referred to in paragraph 2 of this Article in relation to the specific conditions applied to the import of used vehicles by the third country of import linked to the protection of the environment and road safety, when such conditions have been notified by that third country to the Commission. Those conditions shall be verifiable against the information available in the electronic systems referred to in Article 46(1).
4. The Commission shall publish and regularly update in a dedicated online portal the specific conditions notified to it that are linked to the protection of the environment or road safety imposed by third countries referred to in paragraph 3.
Suspension
1. Where there are reasonable grounds to believe that a used vehicle to be exported may not comply with the requirements of this Chapter, the customs authorities shall immediately suspend the release for export of that used vehicle, immediately notify the competent authorities designated under Article 38 of the suspension and transmit all relevant information needed for the competent authorities to determine whether the used vehicle complies with the requirements of this Regulation and may be released for export.
2. For the purpose of determining whether a used vehicle, subject to suspension as referred to in paragraph 1, complies with this Regulation, the competent authorities may request, from any person involved in the export of that used vehicle, additional information, including information on the sale or transfer of vehicle ownership, such as a copy of the invoice or contract, and documentary evidence that that used vehicle is destined for further use.
Release for export
1. Where the release for export of a used vehicle has been suspended in accordance with Article 42, that used vehicle shall be released for export when all the other requirements and formalities relating to such release have been fulfilled and when any of the following conditions is satisfied:
(a)
the competent authorities designated under Article 38 have not requested, within four working days from the beginning of the suspension, the customs authorities to maintain the suspension; or
(b)
the competent authorities designated under Article 38 have informed the customs authorities of their approval for release for export pursuant to this Chapter.
2. The release for export shall not be deemed proof of compliance with Union law and, in particular, with this Regulation or Regulation (EU) No 952/2013.
3. Customs authorities shall automatically notify the exit of the vehicle from the Union through the interconnection referred to in Article 46(4) to the vehicle registration authority of the Member State of last registration. The vehicle registration authority shall record in its national vehicle register that the vehicle was exported to a third country.
Refusal to release for export
1. Where the competent authority concludes that a used vehicle for which the suspension has been notified in accordance with Article 42 does not comply with this Chapter, the competent authority shall immediately require the customs authorities not to release it for export and notify them thereof.
2. Upon the notification from the competent authority pursuant to paragraph 1, the customs authorities shall not release the used vehicle for export.
Cooperation among authorities and exchange of information
1. Competent authorities of Member States shall mutually assist one another in the implementation of this Chapter through exchange of information at bilateral level, in particular for the purpose of verifying the status of a vehicle, including the verification of its registration status in the Member State in which it was previously registered.
2. Where appropriate, competent authorities of Member States shall also cooperate with administrative authorities from third countries. Such cooperation may include sharing of relevant information, conducting joint inspections, and other forms of mutual assistance as deemed necessary to ensure compliance with applicable laws and regulations governing the export of used vehicles.
3. Customs authorities and competent authorities of Member States shall cooperate in accordance with Article 47(2) of Regulation (EU) No 952/2013 and exchange information necessary for the fulfilment of their functions under this Regulation, including via electronic means. The customs authorities may communicate, in accordance with Article 12(1) and Article 16(1) of Regulation (EU) No 952/2013, confidential information acquired by the customs authorities in the course of performing their duties, or provided to the customs authorities on a confidential basis, to the competent authority of the Member State where the operator or trader is established.
4. Where competent authorities have received information in accordance with paragraphs 1 to 3, those competent authorities may communicate that information to competent authorities from other Member States.
5. Risk-related information shall be exchanged as follows:
(a)
between customs authorities in accordance with Article 46(5) of Regulation (EU) No 952/2013;
(b)
between customs authorities and the Commission in accordance with Article 47(2) of Regulation (EU) No 952/2013;
(c)
between customs authorities and competent authorities, including competent authorities from other Member States, in accordance with Article 47(2) of Regulation (EU) No 952/2013.
Electronic systems
1. The MOVE-HUB electronic system developed by the Commission shall be used for the exchange of the VIN and other information on the vehicle registration and roadworthiness status between the national vehicle registers and electronic systems on roadworthiness of the Member States, as well as, to interconnect to the EU Single Window Environment for Customs, where necessary for the controls and requirements laid down in this Chapter.
2. The MOVE-HUB electronic system referred to in paragraph 1 shall provide at least the following functionalities:
(a)
to exchange the data in real time with the national vehicle registers and national electronic systems on roadworthiness of the Member States interconnected with it;
(b)
to enable an automated electronic check of data provided in a roadworthiness certificate as referred to in Annex II to Directive 2014/45/EU, of the date of first registration of a vehicle, as well as of the Member State where a vehicle was last registered, as referred to in Directive 1999/37/EC, to determine whether a used vehicle to be exported complies with the requirements laid down in Article 39, Article 40(1) and Article 41;
(c)
to interconnect to the EU Single Window Environment for Customs in accordance with Regulation (EU) 2022/2399 for the purpose of exchanging data, and support the process of exchanging information referred to in Articles 40(1) and Article 41(2), as well as support the notifications referred to in Articles 42, 43 and 44;
(d)
for the purposes of cooperation with third countries under Article 45(2), to allow the electronic exchange of information with the competent authorities of third countries which have notified to the Commission pursuant to Article 41(2) the specific conditions for the import of used vehicles that they apply.
3. Member States shall interconnect their national vehicle registers and national electronic systems on roadworthiness with the MOVE-HUB electronic system referred to in paragraph 1. That interconnection shall be operational within two years following the adoption of the implementing act referred to in paragraph 5.
4. The Commission shall interconnect the MOVE-HUB system referred to in paragraph 1 of this Article with the European Union Customs Single Window Certificates Exchange System established in Article 4 of Regulation (EU) 2022/2399, so that the automated controls referred to in Article 40 and Article 41(2) and the notifications referred to in Articles 42, 43 and 44 can be performed. That interconnection shall be operational within four years following the adoption of the implementing act referred to in paragraph 5 of this Article.
5. The Commission shall, by 30 September 2028, adopt the implementing acts laying down the necessary arrangements for the implementation of the functionalities of the MOVE-HUB referred to in paragraph 2, including the technical measures necessary for the interconnection of national electronic systems with the MOVE-HUB, the conditions of connection to MOVE-HUB, the data to be transmitted by the national systems and the format for the transmission of that data through the interconnected national systems. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 52(2).
Inspections
1. Member States shall, for the purpose of enforcing this Regulation, establish inspection strategies aimed at detecting illegal activities in the area of collection, and treatment and export of end-of-life vehicles and their parts and components. Those strategies shall provide for the inspections referred to in paragraphs 2, 3 and 4.
2. Member States shall, for the purpose of enforcing this Regulation, inspect:
(a)
authorised treatment facilities;
(b)
collection points;
(c)
other facilities and economic operators which might be involved in the collection, treatment and export of end-of-life vehicles, or selling used spare parts and components.
3. The total number of operators listed in paragraph 2 that shall be subject to inspection each calendar year shall be calculated as being at least 10 % of the operators listed in paragraph 2, points (a) and (b).
4. Member States shall also carry out regular and risk-based inspections concerning export of used vehicles in order to verify compliance with Article 39.
5. In order to distinguish between used vehicles and end-of-life vehicles, competent authorities of Member States may inspect shipments of used vehicles suspected to be end-of-life vehicles on compliance with the requirements laid down in Article 36 and Annex I and monitor such shipments accordingly.
6. Where the competent authorities of a Member State establish that an intended shipment of a used vehicle involves one or more end-of-life vehicles, the costs of appropriate analyses, inspections and storage of the vehicles suspected to be end-of-life vehicles may be charged to the persons arranging the shipment of those vehicles.
Enforcement cooperation at national level and between Member States
1. Member States shall establish, as regards all relevant competent authorities involved in the enforcement of this Regulation, effective mechanisms to enable those authorities to cooperate and coordinate domestically concerning the development and implementation of enforcement policies and activities related to monitoring vehicles registration, de-registration, suspension and cancellation of the registration, certification of destruction, export of used vehicles as well as prevention of illegal treatment and export of end-of-life vehicles.
2. Member States shall cooperate bilaterally and multilaterally with one another in order to facilitate the prevention and detection of illegal treatment and export of end-of-life vehicles and to address the issue of missing vehicles. They shall exchange relevant information on vehicle registration, de-registration and suspension and cancellation of the registration, through the electronic exchange system referred to in Article 46. They shall also exchange relevant information on authorised treatment facilities and repair and maintenance operators not permitted as authorised treatment facilities, and other facilities and economic operators, which may perform operations concerning treatment of end-of-life vehicles. They shall share information, experience and knowledge on illegal activities linked to end-of-life vehicles, enforcement measures and joint actions on a regular basis within established structures, such as enforcement networks, agencies and the Committee established pursuant to Article 52 of this Regulation.
The exchange of vehicle registration data shall include access to and exchange of data on performance and the nature and results of the checks carried out with other Member States’ competent authorities to facilitate the enforcement of this Regulation.
3. Member States shall notify to the Commission the members of their permanent staff that are responsible for the cooperation referred to in paragraph 2 of this Article and Article 45.
Penalties
By 1 September 2029, Member States shall lay down the rules on penalties applicable to infringements of Article 15(1), Article 16, Article 18(1), Article 22(1) and (2), Articles 23 and 24, Article 25(1) and (2), Articles 26 to 31 and Articles 33, 34, 36, 37 and 39 of this Regulation, and shall take all measures necessary to ensure that they are implemented. The penalties provided for shall be effective, proportionate and dissuasive. Member States shall, without delay, notify the Commission of those rules and of those measures and shall notify it, without delay, of any subsequent amendment affecting them.
Reporting to the Commission
1. From 1 September 2029, Member States shall make publicly available in an aggregated form for each calendar year and in the format established by the Commission pursuant to paragraph 5, the following data, which shall be based on information and data received from producers, producer responsibility organisations and waste management operators:
(a)
the number of vehicles registered in the Member State;
(b)
the number of vehicles made available on the market for the first time in the territory of the Member State;
(c)
the number and weight of end-of-life vehicles collected and depolluted in the Member State;
(d)
the number and weight of end-of-life vehicles recycled in the territory of the Member State;
(e)
the number and weight of end-of-life vehicles exported or shipped for further treatment to another Member State or a third country;
(f)
the number and weight of end-of-life vehicles imported or shipped for further treatment from a third country;
(g)
the number of used vehicles released for export and the number of used vehicles imported;
(h)
the number of certificates of destruction issued;
(i)
the total weight and, where relevant, the amount of parts, components and materials removed from end-of-life vehicles for purpose of:
(i)
reuse;
(ii)
remanufacturing or refurbishment;
(iii)
recycling;
(iv)
recovery, including energy recovery;
(v)
disposal;
(j)
the amount and weight of end-of-life vehicles treated in a manner different from that indicated in point (d);
(k)
the amount and weight of end-of-life-vehicles used for backfilling;
(l)
the rates of the targets laid down in Article 33 attained by all waste management operators that are active in the Member State;
(m)
the use of the exemption provided for in Article 29(2), and how it was monitored by the reporting Member State;
(n)
data on the producer responsibility organisations, including the names of the legal persons they represent;
(o)
data on the implementation of Article 21;
(p)
the quantities of parts and components containing relevant amounts of critical raw materials removed from end-of-life vehicles and the quantities of critical raw materials recovered from these parts and components.
Member States shall make the data referred to in the first subparagraph publicly available within 18 months of the end of the reporting period for which it is collected. The data shall be machine readable, sortable and searchable, and shall respect open standards for third party use. Member States shall notify the Commission when the data referred to in the first subparagraph is made available.
The first reporting period shall be the first calendar year after the adoption of the implementing act referred to in paragraph 5.
2. The data made available by Member States in accordance with paragraph 1 shall be accompanied by a quality check report. That information shall be presented in the format established by the Commission pursuant to paragraph 5.
3. Every five years, Member States shall draw up a report summarising:
(a)
incentives introduced to promote the reuse, remanufacturing and refurbishment of parts and components in accordance with Article 32 and their estimated impact;
(b)
the application of penalties and other sanctions envisaged in their national law for infringements of this Regulation adopted in accordance with Article 49, including a list of type of infringements notified and types of measures taken;
(c)
results of inspections carried out in accordance with Article 47;
(d)
the manner of application of definitions of ‘end-of-life vehicle’ and ‘used vehicle’, including practical difficulties encountered in that context.
Member States shall submit that report to the Commission within six months of the end of the five year period which it covers. The first report shall be provided to the Commission by 1 September 2032.
The Commission shall review the reports submitted by the Member States and shall draw up and publish reports on the information received in order to support the evaluation of the implementation of this Regulation in Member States and to facilitate the exchange of information on best practices applied in the Member States.
4. For the purpose of monitoring the implementation of this Regulation, the Commission shall collect and review the information made available in accordance with this Article.
5. The Commission shall adopt implementing acts laying down:
(a)
the methodology and rules for the calculation, verification and reporting of data in accordance with paragraph 1, including:
(i)
the methodology for determining the amount and weight of parts, components and materials removed for purposes referred to in paragraph 1, points (i), (j), (k) and (p);
(ii)
the methodology for determining the weight of recycled waste, including determination of calculation points and measurement points, and, if necessary, possibilities of applying average loss rates;
(iii)
the methodology for calculation and verification of the attainment of the reuse, recycling and recovery targets referred to in Article 33, including in the case of combined shredding of end-of-life vehicles with other waste referred to in Article 27 and Part G, point 3, of Annex VIII;
(b)
the format for the reporting to the Commission referred to in paragraph 1, as well as the format for the quality check report.
Those implementing acts shall be adopted by 31 March 2029, in accordance with the examination procedure referred to in Article 52(2).
6. Producers, producer responsibility organisations, waste management operators and other relevant economic operators shall provide competent authorities with accurate and reliable data allowing Member States to fulfil their reporting obligations under this Article.
Exercise of the delegation
1. The power to adopt delegated acts is conferred on the Commission subject to the conditions laid down in this Article.
2. The power to adopt delegated acts referred to in Articles 5(3), 5(6), 6(6) to (9), 7(3), 11(4), 12(2), 21(2), 22(6), 26(3), 37(3) and 41(3) shall be conferred on the Commission for a period of 5 years from 13 August 2026. The Commission shall draw up a report in respect of the delegation of power no later than nine months before the end of the five-year period. The delegation of power shall be tacitly extended for periods of an identical duration, unless the European Parliament or the Council opposes such extension no later than three months before the end of each period.
3. The delegation of power referred to in Articles 5(3), 5(6), 6(6) to (9),7(3), 11(4), 12(2), 21(2), 22(6), 26(3), 37(3) and 41(3) may be revoked at any time by the European Parliament or by the Council. A decision to revoke shall put an end to the delegation of the power specified in that decision. It shall take effect the day following the publication of the decision in the Official Journal of the European Union or at a later date specified therein. It shall not affect the validity of any delegated acts already in force.
4. Before adopting a delegated act, the Commission shall consult experts designated by each Member State in accordance with the principles laid down in the Interinstitutional Agreement of 13 April 2016 on Better Law-Making.
5. As soon as it adopts a delegated act, the Commission shall notify it simultaneously to the European Parliament and to the Council.
6. A delegated act adopted pursuant to Articles 5(3), 5(6), 6(6) to (9),7(3), 11(4), 12(2), 21(2), 22(6), 26(3), 37(3) and 41(3) shall enter into force only if no objection has been expressed either by the European Parliament or the Council within a period of two months of notification of that act to the European Parliament and to the Council or if, before the expiry of that period, the European Parliament and the Council have both informed the Commission that they will not object. That period shall be extended by two months at the initiative of the European Parliament or of the Council.
Committee procedure
1. The Commission shall be assisted by the committee established by Article 39 of Directive 2008/98/EC. That committee shall be a committee within the meaning of Regulation (EU) No 182/2011.
2. Where reference is made to this paragraph, Article 5 of Regulation (EU) No 182/2011 shall apply.
Amendments to Regulation (EU) 2023/1542
Annex I to Regulation (EU) 2023/1542 is amended in accordance with Annex XII to this Regulation.
Amendments to Regulation (EU) 2019/1020
In Regulation (EU) 2019/1020, Annex II, points 10 and 11 are deleted.
Amendments to Regulations (EU) 2018/858 and (EU) No 168/2013
Annex II to Regulation (EU) 2018/858 and Annex II to Regulation (EU) No 168/2013 are amended in accordance with Annex XI to this Regulation.
Review
1. By 31 December 2035, the Commission shall review and draw up a report on the application of this Regulation and its impact on the environment, human health and the functioning of the single market and submit it to the European Parliament and to the Council. Where appropriate, the report shall be accompanied by a legislative proposal to amend relevant provisions of this Regulation.
2. Taking account of technical progress and practical experience gained in Member States as well as any revision of Regulation (EC) No 1907/2006, the Commission shall, in its report, include an evaluation of the following:
(a)
the need to extend the scope of this Regulation, in particular provisions of Chapters II and III, as well as Chapter IV Section II, to L-category vehicles as defined in Article 4(2) of Regulation (EU) No 168/2013 and vehicles of categories M 2 , M 3 , N 2 , N 3 and O as set out in Article 4(1) of Regulation (EU) 2018/858;
(b)
the need to extend the scope of provisions applicable to vehicles that are type-approved in multi-stage type-approval and to motor caravans and to include trailer caravans into the scope of this Regulation;
(c)
the need to extend the scope of this Regulation, in particular provisions of Chapters VI to L-category-vehicles, as defined in Article 4(2) of Regulation (EU) No 168/2013;
(d)
the measures concerning provision of information on substances of concern present in vehicles and the need of introducing further provisions addressing substances of concern that may affect high-quality recycling of vehicles at their end-of-life;
(e)
the measures regarding management of end-of-life vehicles laid down in Chapter IV, including the levels of targets laid down in Article 33 and the need of their revision;
(f)
the need to extend the scope of this Regulation with regard to recycling target levels as laid down in Article 33, to the vehicle categories to which Article 33 does not apply under this Regulation;
(g)
infringements and the effectiveness, proportionality and dissuasiveness of penalties as set out in Article 49;
(h)
the need to amend Article 5;
(i)
the extent to which the issue of missing vehicles has been solved, including estimates on the number of missing vehicles and the impact of the measures regarding export of used vehicles, and the need to include further measures addressing the issue of the traceability of vehicles;
(j)
the requirements for recycled plastic content, including targets and obligations for recycling installations in and outside the Union as laid down in Article 6(1) to (4) of this Regulation, and the need for revision on that basis, including an evaluation of developments for steel and aluminium relating to Article 6(7) and (8) of this Regulation and under other relevant Union legislation, such as Regulation (EU) 2025/40 or Regulation (EU) 2024/1781, to ensure coherence and alignment;
(k)
the cost allocation mechanism for vehicles becoming end-of-life vehicles in another Member State laid down in Article 22 and the need for its revision;
(l)
provisions on processes that may affect high-quality recycling of vehicles at their end-of-life;
(m)
the impact of differences in the national roadworthiness criteria on the used vehicles exports.
(n)
the effectiveness, interoperability and reliability of national vehicle registration systems and their cross border exchange of information in ensuring the accurate identification, status and traceability of vehicles throughout their lifecycle, with particular attention to:
(i)
the impact of temporary de-registration on the accuracy, accessibility, and traceability of vehicle records, including its role in identifying missing vehicles;
(ii)
the need for minimum requirements for vehicle deregistration across the Union, such as establishing a maximum duration and strict renewal conditions, to strengthen vehicle traceability and prevent their illegal treatment.
3. By 31 December 2033, the Commission shall review the state of technological development, environmental and economic performance and availability of biobased plastic content and of elastomers derived from the reprocessing of tyres in new vehicles, taking into consideration the sustainability criteria laid down in Article 29 of Directive (EU) 2018/2001 and any sustainability criteria to be laid down for tyres under Regulation (EU) 2024/1781.
4. Where appropriate, and based on the review referred to in paragraph 3, the Commission may present a legislative proposal in order to:
(a)
lay down sustainability requirements for biobased feedstock in plastic used in vehicles;
(b)
lay down targets to increase the use of biobased feedstock in plastic used in vehicles;
(c)
lay down targets to include the use of elastomers derived from the reprocessing of tyres from vehicles;
(d)
assess to which extent the targets referred to in point (b) may be combined with or added to the targets set out in Article 6(1);
(e)
assess to which extent the targets referred to in point (c) may be combined with the targets set out in Article 6(1);
(f)
modify, where appropriate, the definition of biobased plastic set out in Article 3(1), point (53), of Regulation (EU) 2025/40, the definition of plastic in Article 3(1), point (9), of this Regulation and the scope of the recycled plastic targets as specified in Article 6(1) of this Regulation;
(g)
modify, where appropriate, the calculation and verification methodology as referred to in Article 6(2) and the requirements for installations processing elastomers from tyres based in the Union and in third countries.
5. Where appropriate to ensure the effective and uniform end-of-life vehicles’ traceability, and based on the review referred to in paragraph 2, point (n), the Commission may present a legislative proposal on deregistration rules of vehicles throughout the Union.
6. By 14 August 2031, the Commission shall conduct an assessment to evaluate, based on the declarations made under Article 10, whether manufacturers are on track to comply with the recycled plastic targets laid down in Article 6(1). The assessment shall particularly evaluate:
(a)
the availability of suitable plastic recycling technologies;
(b)
the sufficient availability of recycled plastic;
(c)
the level of quality of recycled plastic comparing to the level of safety required; and
(d)
technical and economic difficulties to reach the recycled plastic targets.
On the basis of that assessment, the Commission may, where appropriate, submit a legislative proposal to the European Parliament and to the Council to amend the targets laid down in Article 6(1) in order to provide for derogations from the scope, timing or level of minimum percentages set out therein.
Repeal and transitional provisions
1. Directive 2000/53/EC is repealed with effect from 1 September 2028.
However, the following provisions of Directive 2000/53/EC shall continue to apply:
(a)
Article 4(2) and Annex II, until 31 August 2032; however, entries 5(a), 5(b)(i), 5(b)(ii) and 16 of Annex II to Directive 2000/53/EC shall cease to apply from 13 August 2026;
(b)
Article 5(4), second subparagraph, Article 6(3), second subparagraph, Article 7(1), Article 8(3) and (4), until 31 August 2029;
(c)
Article 6(3), first subparagraph, and Annex I until 31 August 2029;
(d)
Article 7(2), point (b), until 31 December 2030;
(e)
Article 9(1a), first and third subparagraphs, Article 9(1b) and Article 9(1d), until 31 August 2029;
(f)
Article 9(1a), second subparagraph, until 31 August 2031.
2. Directive 2005/64/EC is repealed with effect from 31 August 2032.
However, its Article 6(3) is repealed with effect from 31 August 2029.
3. References to the repealed Directives shall be construed as references to this Regulation and shall be read in accordance with the correlation tables in Annex XV.
4. By way of derogation from Article 8(2) of this Regulation, until 14 August 2032, where that Article refers to Article 4 of this Regulation, such a reference shall be construed as a reference to Article 5 of Directive 2005/64/EC.
By way of derogation from Article 8(2) of this Regulation, until 14 August 2032, where that Article refers to Article 5 of this Regulation, such a reference shall be construed as a reference to Article 6(2) of Directive 2005/64/EC.
Applicability to and in the United Kingdom in respect of Northern Ireland
1. Article 14 shall apply only in respect of Article 30, Article 31 and Article 35(1) to and in the United Kingdom in respect of Northern Ireland.
2. Articles 15 to 29, Articles 32, 33 and 34 and Article 35(2) shall not apply to and in the United Kingdom in respect of Northern Ireland.
3. Article 47(2), point (a), and Article 47(3) shall not apply to and in the United Kingdom in respect of Northern Ireland.
4. Article 48(1) and (2) shall not apply as regards the prevention of illegal treatment of end-of-life vehicles to and in the United Kingdom in respect of Northern Ireland.
5. Article 48(2) shall not apply as regards the exchange of relevant information on authorised treatment facilities to and in the United Kingdom in respect of Northern Ireland.
6. Article 49 shall not apply to and in the United Kingdom in respect of Northern Ireland as regards Article 15(1), Article 16, Article 19(1), Article 22(1) and (2), Article 23, Article 24, Article 25(1) and (2), Articles 27 to 29, Article 33 and Article 34.
7. Article 50(1), points (c), (d), (h), (i)(iii), (i)(iv), (i)(v), (j), (k), (l), (m), (n) and (o) and Article 50(3), point (a), shall not apply to and in the United Kingdom in respect of Northern Ireland.
Entry into force and application
1. This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union .
2. It shall apply from 1 September 2028.
However, Articles 4(3), 5(2) to (9), 6(4) to (9), 6(11), 7(3), 7(4), 9(7), 11(4), 12(2), 13(6), 14(4), 15(6), 21(2), 22(6), 26(3), 37(3), 41(3), 46(5) and 50(5) shall apply from 14 September 2026, Article 53 shall apply from 13 August 2026 and Article 55 shall apply from 1 September 2032.
Supplementary provisions
CRITERIA FOR DETERMINATION WHETHER A VEHICLE IS AN END-OF-LIFE VEHICLE
ANNEX ISupplementary provisions
ANNEX I
CRITERIA FOR DETERMINATION WHETHER A VEHICLE IS AN END-OF-LIFE VEHICLE
This Annex establishes the criteria to determine whether a vehicle is an end-of-life vehicle, and shall be applied as follows:
Part A lays down the criteria to assess the irreparability of a vehicle. If one or more of these criteria are met, the vehicle shall be considered to be an end-of-life vehicle.
If none of the criteria of Part A are met, the vehicle shall be assessed in accordance with the criteria provided for in Part B. If one or more of the criteria of Part B are met, a technical assessment shall determine which repairs are needed to obtain a roadworthiness certificate in accordance with Directive 2014/45/EU in the Member State where the vehicle was registered before repair. Based on that technical assessment, the vehicle owner shall decide whether he or she wants to discard the vehicle.
If, within five years of that technical assessment, the vehicle owner does not obtain a roadworthiness certificate in accordance with Directive 2014/45/EU, the vehicle shall be considered to be an end-of-life vehicle. For the period of those five years, that technical assessment shall constitute documentation that the vehicle is not an end-of-life vehicle.
The assessment referred to in this Annex shall be conducted by an independent automotive expert. Member States may establish an exhaustive list of independent automotive experts to carry out those assessments.
Following a request by a vehicle owner, the competent authorities of the Member State of registration of a vehicle, or one of its appointed authorising bodies, may exempt a vehicle that is considered to be an end-of-life vehicle in accordance with this Annex from being an end-of-life vehicle, when the vehicle concerned is subject to repair,.
PART A
CRITERIA FOR ASSESSMENT OF END-OF-LIFE VEHICLES
A vehicle is an end-of-life vehicle when it meets one or more of the following criteria:
(a)
it has been cut into pieces or dismantled for reuse of its parts;
(b)
it has been burnt to the point where the engine compartment or passenger compartment is completely destroyed;
(c)
it has been submerged in water to a level above the dashboard;
(d)
one or several of the following components of the vehicle can, from a technical point of view, be neither repaired nor replaced:
(i)
ground coupling components (such as tyres and wheels), suspension, steering, braking, and their control components;
(ii)
seat fixings and joints;
(iii)
airbags, pre-tensioners, safety belts, and their peripheral operating components;
(iv)
the vehicle’s hull and chassis or shell;
(e)
its structural and safety components have technical defects that are irreversible and that render them non-replaceable;
(f)
it was handed over for treatment to a collection point or an authorised treatment facility;
(g)
it has been declared as a total technical loss by an insurance company, based on the technical assessment carried out by an automotive expert.
PART B
LIST OF INDICATIVE CRITERIA FOR END-OF-LIFE VEHICLES
If none of the criteria of Part A apply, the vehicle shall be assessed in accordance with the following criteria:
(a)
it is abandoned or the means allowing it to be identified are lacking, in particular the VIN;
(b)
it is not appropriately protected against damage during storage, transportation, loading and unloading;
(c)
the costs necessary to repair the vehicle to a technical condition that would be sufficient to obtain a roadworthiness certificate added to its current value exceed its estimated market value after repair;
(d)
it has been submerged in water to a level below the dashboard, with damage to the engine or electrical system;
(e)
its fuel or fuel vapours have been discharged, posing a risk of fire and explosion;
(f)
gas has leaked from its liquid gas system posing a risk of fire and explosion;
(g)
its operating liquids (fuel, brake fluid, anti-freeze liquid, battery acid electrolyte solution, cooling liquid) have been discharged, posing a risk of water pollution;
(h)
it has been dismantled; or
(i)
it has one or more entry points welded up or closed by insulating foam.
CRITERIA FOR RECOGNISING THE STATUS OF VEHICLES OF SPECIAL CULTURAL INTEREST
ANNEX IISupplementary provisions
ANNEX II
CRITERIA FOR RECOGNISING THE STATUS OF VEHICLES OF SPECIAL CULTURAL INTEREST
1.
The competent authorities of the Member State of registration of a vehicle, or one of its appointed authorising bodies, may recognise a vehicle as having a special cultural interest when it meets all of the following criteria:
(a)
its unique historical or cultural value or status has been documented by the vehicle owner or by the competent authorities of the Member State where a vehicle is registered or it is a single modified or custom-built vehicle which has been individually approved in accordance with Regulation (EU) 2018/858 or national law;
(b)
the vehicle owner is known and can be identified;
(c)
the parts of the vehicle can be identified by a serial number, or other identification provided by the manufacturer or assigned by the competent authority;
(d)
the vehicle can be identified by the VIN, or serial number, or other identification provided by the manufacturer or assigned by a competent authority.
Upon request by the vehicle owner, the competent authorities of the Member State of registration shall issue a certificate recognising a vehicle as having a special cultural interest where the criteria set out in the first subparagraph of this point are fulfilled.
Upon request by the vehicle owner, the competent authorities of the Member State of registration shall revoke the certificate referred to in the second subparagraph of this point.
2.
The owner of the vehicle of special cultural interest shall ensure that:
(a)
the vehicle is stored, transported or used in environmentally sound manner in accordance with Union or national law;
(b)
the certificate referred to in the second subparagraph of point 1 is provided or made available to authorities upon request.
3.
The compliance of the vehicle with the criteria of points 1 and 2 shall be verified at least every five years, or in the event of a change of ownership.
CALCULATION OF THE RATES OF REUSABILITY, RECYCLABILITY AND RECOVERABILITY
ANNEX IIISupplementary provisions
ANNEX III
CALCULATION OF THE RATES OF REUSABILITY, RECYCLABILITY AND RECOVERABILITY
For the purposes of this Annex, ‘reference vehicle’ means the version within a vehicle type, which is identified by the type-approval authority, in consultation with the manufacturer and in accordance with the criteria laid down in Part A, as being the most problematic in terms of reusability, recyclability and recoverability.
PART A
1.
The materials present in the vehicle and their respective shares and locations shall be specified, together with any relevant information necessary to correctly calculate the rates of recyclability and recoverability.
2.
Masses shall be expressed in kg with one decimal place. The rates shall be calculated as a percentage with one decimal place, then rounded as follows:
(a)
if the figure following the decimal point is between 0 and 4, the total is rounded down;
(b)
if the figure following the decimal point is between 5 and 9, the total is rounded up.
3.
For the purposes of the selection of the reference vehicles, account shall be taken of the following criteria:
(a)
the type of bodywork;
(b)
the available trim levels;
(c)
the available optional equipment which can be fitted under the manufacturer’s responsibility.
4.
Should the type-approval authority and the manufacturer fail jointly to identify the most problematic version within a type of vehicle, in terms of reusability, recyclability and recoverability, one reference vehicle shall be selected, within:
(a)
each ‘type of bodywork’, as defined in part C, point 2, of Annex I to Regulation (EU) 2018/858 in the case of M 1 vehicles;
(b)
each ‘type of bodywork’, i.e. van, chassis-cab, pick-up, etc., in the case of N 1 vehicles.
5.
For the purposes of checks of the materials and masses of component parts, the manufacturer shall make available vehicles and component parts as deemed necessary by the type-approval authority.
PART B
1.
In order to be considered as reusable, components or parts shall be removable in a readily and non-destructive manner.
2.
The total mass of reusable parts, components and materials shall be considered as 100 % reusable, recyclable and recoverable.
3.
Parts, components and materials listed in Part B, points 1, 2 and 3, of Annex VIII shall be considered as 0 % reusable and 100 % recyclable and recoverable. Parts and components listed in Part E of Annex VIII shall be considered as 0 % reusable and 100 % recyclable and recoverable. The methodology shall ensure, that in case of an amendment to Annex VIII resulting in the extension of the list of parts and components listed in Part E of that Annex, the newly added parts and components shall be considered as 0 % reusable and 100 % recyclable and recoverable.
4.
The calculation of the rates of reusability, recyclability and recoverability shall be coherent with the circularity strategy, reflecting technological progress in end-of-life treatment technologies.
CONDITIONS AND MAXIMUM CONCENTRATION VALUES FOR THE PRESENCE OF LEAD, MERCURY, CADMIUM AND HEXAVELENT CHROMIUM IN MATERIALS, PARTS AND COMPONENTS
ANNEX IVSupplementary provisions
ANNEX IV
CONDITIONS AND MAXIMUM CONCENTRATION VALUES FOR THE PRESENCE OF LEAD, MERCURY, CADMIUM AND HEXAVELENT CHROMIUM IN MATERIALS, PARTS AND COMPONENTS
A maximum concentration value of substances up to 0,1 % by weight in homogeneous material for lead, hexavalent chromium and mercury and up to 0,01 % by weight in homogeneous material for cadmium shall be tolerated.
Spare parts placed on the market after 1 July 2003 which are used for vehicles placed on the market before 1 July 2003, except for wheel balance weights, carbon brushes for electric motors and brake linings, shall be exempted from Article 5(4).
Homogenous materials, parts and components
Scope and expiry date of the exemption
To be labelled or made identifiable in accordance with Article 5(6), point (d)
Lead as an alloying element
1(a).
Steel for machining purposes and batch hot dip galvanised steel components containing up to 0,35 % lead by weight
1(b).
Continuously galvanised steel sheet containing up to 0,35 % lead by weight
Vehicles type approved before 1 January 2016 and spare parts for such vehicles
2(a).
Aluminium for machining purposes with a lead content up to 2 % by weight
As spare parts for vehicles placed on the market before 1 July 2005
2(b).
Aluminium with a lead content up to 1,5 % by weight
As spare parts for vehicles placed on the market before 1 July 2008
2(c)(i).
Aluminium alloys for machining purposes with a lead content up to 0,4 % by weight
Vehicles type-approved before 1 January 2028 and spare parts for such vehicles
2(c)(ii).
Aluminium alloys not included in entry 2(c)(i) with a lead content up to 0,4 % by weight ( 2 )
Vehicles type-approved before 1 January 2027 and spare parts for such vehicles
2(c)(iii).
Aluminium casting alloys containing up to 0,3 % lead by weight provided that the lead stems from lead-bearing aluminium scrap recycling
Vehicles type-approved after 31 December 2026 and spare parts for these vehicles. ( 1 )
3.
Copper alloys containing up to 4 % lead by weight
( 1 )
4(a).
Bearing shells and bushes
As spare parts for vehicles placed on the market before 1 July 2008
4(b).
Bearing shells and bushes in engines, transmissions and air conditioning compressors
As spare parts for vehicles placed on the market before 1 July 2011
Lead and lead compounds in components
5.
(deleted)
6.
Vibration dampers
Vehicles type approved before 1 January 2016 and spare parts for such vehicles
X
7(a).
Vulcanising agents and stabilisers for elastomers in brake hoses, fuel hoses, air ventilation hoses, elastomer/metal parts in the chassis applications, and engine mountings
As spare parts for vehicles placed on the market before 1 July 2005
7(b).
Vulcanising agents and stabilisers for elastomers in brake hoses, fuel hoses, air ventilation hoses, elastomer/metal parts in the chassis applications, and engine mountings containing up to 0,5 % lead by weight
As spare parts for vehicles placed on the market before 1 July 2006
7(c).
Bonding agents for elastomers in powertrain applications containing up to 0,5 % lead by weight
As spare parts for vehicles placed on the market before 1 July 2009
Lead in solders or coatings of electrical and electronic applications specified in the following subentries
8(a).
Lead in solders to attach electrical and electronic components to electronic circuit boards and lead in finishes on terminations of components other than electrolyte aluminium capacitors, on component pins and on electronic circuit boards
Vehicles type approved before 1 January 2016 and spare parts for such vehicles
X ( 3 )
8(b).
Lead in solders in electrical applications other than soldering on electronic circuit boards or on glass
Vehicles type approved before 1 January 2011 and spare parts for such vehicles
X ( 3 )
8(c).
Lead in finishes on terminals of electrolyte aluminium capacitors
Vehicles type approved before 1 January 2013 and spare parts for such vehicles
X ( 3 )
8(d).
Lead used in soldering on glass in mass airflow sensors
Vehicles type approved before 1 January 2015 and spare parts of such vehicles
X ( 3 )
8(e).
Lead in high melting temperature type solders (i.e. lead-based alloys containing 85 % by weight or more lead)
( 1 )
X ( 3 )
8(f)(i).
Lead in compliant pin connector systems
Vehicles type approved before 1 January 2017 and spare parts for such vehicles
X ( 3 )
8(f)(ii).
Lead in compliant pin connector systems other than the mating area of vehicle harness connectors
Vehicles type approved before 1 January 2024 and spare parts for such vehicles
X ( 3 )
8(g)(i).
Lead in solders to complete a viable electrical connection between semiconductor die and carrier within integrated circuit flip chip packages
Vehicles type approved before 1 October 2022 and spare parts for such vehicles
X ( 3 )
8(g)(ii).
Lead in solders to complete a viable electrical connection between the semiconductor die and the carrier within integrated circuit flip chip packages where that electrical connection consists of any of the following:
(1)
a semiconductor technology node of 90 nm or larger;
(2)
a single die of 300 mm 2 or larger in any semiconductor technology node;
(3)
stacked die packages with dies of 300 mm 2 or larger, or silicon interposers of 300 mm 2 or larger.
(1)
Vehicles type-approved before 1 January 2030 and spare parts for such vehicles
X ( 3 )
8(h).
Lead in solder to attach heat spreaders to the heat sink in power semiconductor assemblies with a chip size of at least 1 cm 2 of projection area and a nominal current density of at least 1 A/mm 2 of silicon chip area
Vehicles type approved before 1 January 2016 and spare parts for such vehicles
X ( 3 )
8(i).
Lead in solders in electrical glazing applications on glass except for soldering in laminated glazing
Vehicles type approved before 1 January 2016 and spare parts for such vehicles
X ( 3 )
8(j).
Lead in solders for soldering of laminated glazing
Vehicles type approved before 1 January 2020 and spare parts for such vehicles
X ( 3 )
8(k).
Soldering of heating applications with 0,5 A or more of heat current per related solder joint to single panes of laminated glazings not exceeding wall thickness of 2,1 mm. This exemption does not cover soldering to contacts embedded in the intermediate polymer.
Vehicles type approved before 1 January 2024 and spare parts for such vehicles
X ( 3 )
9.
Valve seats
As spare parts for engine types developed before 1 July 2003
10(a).
Electrical and electronic components, which contain lead in a glass or ceramic, in a glass or ceramic matrix compound, in a glass-ceramic material, or in a glass-ceramic matrix compound. This exemption does not cover the use of lead in:
(i)
glass in bulbs and glaze of spark plugs;
(ii)
dielectric ceramic materials of components listed under 10(b), 10(c) and 10(d).
X ( 4 ) (for components other than piezo in engines)
10(b).
Lead in PZT based dielectric ceramic materials of capacitors being part of integrated circuits or discrete semiconductors
10(c).
Lead in dielectric ceramic materials of capacitors with a rated voltage of less than 125 V AC or 250 V DC
Vehicles type approved before 1 January 2016 and spare parts for such vehicles
10(d).
Lead in the dielectric ceramic materials of capacitors compensating the temperature-related deviations of sensors in ultrasonic sonar systems
Vehicles type approved before 1 January 2017 and spare parts for such vehicles
11.
Pyrotechnic initiators
Vehicles type approved before 1 July 2006 and spare parts for such vehicles
12.
Lead-containing thermoelectric materials in automotive electrical applications to reduce CO 2 emissions by recuperation of exhaust heat
Vehicles type approved before 1 January 2019 and spare parts for such vehicles
X
Hexavalent chromium
13(a).
Corrosion preventive coatings
As spare parts for vehicles placed on the market before 1 July 2007
13(b).
Corrosion preventive coatings related to bolt and nut assemblies for chassis applications
As spare parts for vehicles placed on the market before 1 July 2008
14.
Hexavalent chromium as an anti-corrosion agent of the carbon steel cooling system in absorption refrigerators up to 0,75 % by weight in the cooling solution:
X
(a)
designed to operate fully or partly with electrical heater, having an average utilised electrical power input < 75 W at constant running conditions;
For (a): Vehicles type approved before 1 January 2020 and spare parts for such vehicles
(b)
designed to operate fully or partly with electrical heater, having an average utilised electrical power input ≥ 75 W at constant running conditions;
(c)
designed to fully operate with non-electrical heater.
For (b): Vehicles type approved before 1 January 2026 and spare parts for such vehicles
Mercury
15(a).
Discharge lamps for headlight application
Vehicles type approved before 1 July 2012 and spare parts for such vehicles
X
15(b).
Fluorescent tubes used in instrument panel displays
Vehicles type approved before 1 July 2012 and spare parts for such vehicles
X
( 1 ) This exemption shall be reviewed in 2030 in accordance with Article 5(6).
( 2 ) Applies to aluminium alloys where lead is not intentionally introduced, but is present due to the use of recycled aluminium.
( 3 ) Dismantling if, in correlation with entry 10(a), an average threshold of 60 grams per vehicle is exceeded. For the purposes of this note, electronic devices not installed by the manufacturer on the production line shall not be taken into account.
( 4 ) Dismantling if, in correlation with entries 8(a) to 8(k), an average threshold of 60 grams per vehicle is exceeded. For the purposes of this note, electronic devices not installed by the manufacturer on the production line shall not be taken into account.
CIRCULARITY STRATEGY
ANNEX VSupplementary provisions
ANNEX V
CIRCULARITY STRATEGY
PART A
ELEMENTS OF THE CIRCULARITY STRATEGY
1.
A non-technical description of the actions planned to ensure that the vehicles meet the requirements of Articles 4 to 7 throughout their production.
2.
A non-technical description of procedures implemented by the manufacturer to:
(a)
collect the data through the full supply chain relevant for meeting the requirements of Articles 4 to 7;
(b)
check and verify the information received from suppliers;
(c)
react adequately where the data received from the suppliers indicate a risk of non-compliance with the requirements of Article 4, 5 or 6.
3.
Information on end-of-life treatment technologies in place, expected technological progress in end-of-life treatment technologies and capacity investment in such technologies, that the manufacturer used in order to calculate the reusability, recyclability and recoverability in accordance with Article 4 of their vehicle types.
4.
Information on the share of recycled content in vehicles as referred to in Articles 6 and 10.
5.
A list of actions that the manufacturer commits to carry out in order to ensure that the treatment of end-of-life vehicles is carried out in accordance with this Regulation, with a particular focus on:
(a)
measures designed to facilitate removal of parts indicated in Part C of Annex VIII;
(b)
measures to address the challenges posed by the use of materials and techniques which hamper easy dismantling or which make recycling very challenging;
(c)
measures to promote the reuse of parts and components;
(d)
research and development activities, investments in the development of recycling technologies or infrastructure, as well as cooperation with waste management operators, conducted in order to implement the actions referred to in points (a) to (c).
PART B
FOLLOW-UP AND UPDATE OF THE CIRCULARITY STRATEGY
1.
The manufacturers shall provide an update of the circularity strategy at least every five years.
2.
The updated circularity strategy shall include the relevant changes and in particular the following:
(a)
a description of how the actions referred to in point 5 of Part A have been undertaken, together with an assessment of their effectiveness, and, where one or more actions indicated in the strategy has not been conducted, an explanation of the reasons for this;
(b)
information about the significant changes in the design and production undertaken by the manufacturer to improve the circularity of vehicles.
INFORMATION REQUIREMENTS ON REMOVAL AND REPLACEMENT
ANNEX VISupplementary provisions
ANNEX VI
INFORMATION REQUIREMENTS ON REMOVAL AND REPLACEMENT
1.
Electric vehicle batteries and light means of transport batteries incorporated in the vehicle:
(a)
original equipment number;
(b)
location;
(c)
weight;
(d)
type of battery chemistry;
(e)
instructions for safe discharging of the battery;
(f)
technical instructions on removal and replacement, including the sequence of all steps and types of joining, fastening, sealing techniques;
(g)
tools or technologies required for the access, removal and replacement of the electric vehicle batteries and light means of transport batteries.
2.
E-drive motors incorporated in the vehicle:
(a)
original equipment number;
(b)
location;
(c)
weight;
(d)
the types of permanent magnets present in e-drive motors as listed in Article 28(1), point (b), of Regulation (EU) 2024/1252;
(e)
technical instructions on removal and replacement, including the sequence of all steps and types of joining, fastening, sealing techniques;
(f)
tools or technologies required for the access, removal and replacement of the e-drive motors.
3.
Components, parts and materials listed in Part B of Annex VIII:
(a)
original equipment number;
(b)
location;
(c)
weight;
(d)
presence of the substances listed in Article 5(4), which need to be labelled as referred to in Annex IV in a vehicle;
(e)
technical instructions on removal, including the sequence of all steps;
(f)
availability of best treatment techniques.
4.
Components, parts and materials listed in Part C of Annex VIII:
(a)
original equipment number;
(b)
location;
(c)
technical instructions on removal and replacement, including the sequence of all steps;
(d)
information, specifications, tools and processes, including software updates, required for remanufacturing and refurbishment.
5.
Digitally coded components and parts in a vehicle:
(a)
number;
(b)
location;
(c)
technical instructions on access, removal and replacement of components, including coding and software necessary to activate spare parts and components to function in another vehicle, and process information concerning their deregistering and decoupling from a VIN including, where relevant, instruction on how to use a diagnostic tool with a view to their future reuse;
(d)
description on functionality, interchangeability and compatibility with specific parts and components of other makes and models;
(e)
contact point of the manufacturer for technical assistance.
6.
For the purposes of point 5(c), where deregistering and decoupling from a VIN of digitally coded components, equipment and parts referred to in Article 11 of this Regulation is required, the manufacturer shall put in place processes to allow waste management operators and repair and maintenance operators to perform such deregistering and decoupling. In that process, the manufacturer may require a certificate of destruction, as well as an authentication of the respective operator. For that purpose, waste management operators and repair and maintenance operators shall obtain and use the authentication credentials required for the manufacturer RMI website referred to in point 2.1 of Annex X to Regulation (EU) 2018/858. Where access to the vehicle on-board diagnostic (OBD) information by waste management operators and repair and maintenance operators is required for such deregistering and decoupling processes, the manufacturer may, as a condition for issuing any access credentials:
(a)
require a continuous online connection, at the time of performing the removal, from the diagnostic tool to the diagnostic tool manufacturer’s server as well as from the diagnostic tool manufacturer’s server to the manufacturer’s server; and
(b)
require the manufacturer of the tool used to access the OBD information to attest to the manufacturer the identity of the diagnostic tool and the pseudonymised identity of the operator and to collect and store the VIN, the unique identifier of the part, where available and supported by the vehicle manufacturer process, the UTC date and time stamp for the relevant activity and the unique diagnostic tool identifier; the manufacturer shall obtain, on request, from the manufacturer of the diagnostic tool access to the information referred to in this point where this is necessary to react to a reasonable suspicion of parts theft or misuse.
LABELLING REQUIREMENTS
ANNEX VIISupplementary provisions
ANNEX VII
LABELLING REQUIREMENTS
1.
Vehicle plastic parts, components and materials having a weight of more than 100 grams:
(a)
international standard ISO 1043-1 Plastics – symbols and abbreviated terms. Part 1: Basic polymers and their special characteristics;
(b)
international standard ISO 1043-2 Plastics – symbols and abbreviated terms. Part 2: Fillers and reinforcing materials;
(c)
international standard ISO 11469 Plastics – Generic identification and marking of plastic products.
2.
Vehicle elastomer parts, components and materials having a weight of more than 200 grams, except tyres: international standard ISO 1629 Rubbers and latices – Nomenclature.
3.
The symbols ‘[’ or ‘]’ used in the ISO standards can be substituted by brackets.
TREATMENT REQUIREMENTS
ANNEX VIIISupplementary provisions
ANNEX VIII
TREATMENT REQUIREMENTS
PART A
MINIMUM REQUIREMENTS FOR STORAGE SITES AND TREATMENT SITES
1.
Storage sites, including storage sites in the collection points, for the storage of end-of-life vehicles, prior to their treatment, and of their components, parts and materials, shall:
(a)
have impermeable surfaces with spillage collection facilities, decanters and cleanser-degreasers;
(b)
be equipped for the treatment of water, including rainwater, in compliance with health and environmental requirements;
(c)
have appropriate storage of end-of-life vehicles and stack only depolluted end-of-life vehicles, unless stacking racks are used, to an appropriate height;
(d)
be equipped to enable the immediate removal of fluids and liquids from leaking end-of-life vehicles and the collection of any leaked fluids and liquids using absorbent material.
Operators of the sites referred to in the first subparagraph shall carry out the actions referred to in point (d) of that subparagraph without delay.
2.
Storage shall be organised so as to avoid damage to:
(a)
components and parts containing the liquids and fluids listed in points 1 and 3 of Part B of this Annex;
(b)
components, parts and materials listed in Part C of this Annex.
3.
The sites where end-of-life vehicles and their components, parts and materials are treated shall have:
(a)
impermeable surfaces for appropriate areas with the provision of spillage collection facilities, decanters and cleanser-degreasers;
(b)
appropriate storage for parts, components and materials that have been removed from the end-of-life vehicle, including impermeable storage for oil-contaminated parts, components and materials;
(c)
appropriate containers for storage of batteries (with electrolyte neutralisation on site or elsewhere), filters and PCB/PCT-containing capacitors;
(d)
appropriate separate storage tanks for the segregated storage of end-of-life vehicle fluids: fuels, oils (motor oil, gearbox oil, power steering oil, transmission oil, hydraulic oil), oil filters, cooling liquids, antifreeze, brake fluids, refrigerants, diesel exhaust fluid and any other fluids or gases contained in the end-of-life vehicle;
(e)
equipment for the treatment of water, including rainwater, in compliance with health and environmental requirements;
(f)
appropriate storage for used tyres, taking into account the need to prevent fire hazards and excessive stockpiling.
4.
Authorised treatment facilities that are permitted to treat electric vehicles shall comply with the requirements set out in Annex XII to Regulation (EU) 2023/1542. Authorised treatment facilities accepting electric vehicles with suspected damage to the electric vehicle battery shall assess these batteries as soon as possible but no later than within 24 hours after delivery. Such vehicles and batteries shall be stored separately in a quarantined area as referred to in paragraph 1. The quarantined area shall be equipped with appropriate installations to prevent, detect and constrain electric vehicle battery fires from spreading to other areas, other electric vehicles and other batteries.
PART B
MINIMUM REQUIREMENTS FOR DEPOLLUTION
1.
The following fluids, liquids and gases shall be removed from the end-of-life vehicle, unless they are necessary for the reuse of the parts concerned:
(a)
fuel;
(b)
motor oil;
(c)
transmission oil;
(d)
gearbox oil;
(e)
power steering oil;
(f)
hydraulic oil;
(g)
cooling liquids;
(h)
antifreeze;
(i)
brake fluids;
(j)
refrigerants;
(k)
diesel exhaust fluids; and
(l)
any other fluids or gases contained in the end-of-life vehicle.
After removal of the fluids and liquids, drain plugs shall be applied to prevent leakage of remains. The collection containers shall be labelled to indicate the type of liquid that is contained within them and stored separately from each other in a secure location, compliant with the Part A of this Annex, to prevent accidental spillage, leakage or unauthorised access to it.
2.
The following components, parts and materials shall be neutralised or removed:
(a)
e-call system;
(b)
pyrotechnic parts of airbags;
(c)
pyrotechnic parts of seat belts;
(d)
any other pyrotechnic parts;
3.
The following components, parts and materials shall be removed from end-of-life vehicles:
(a)
airbags, liquefied petroleum gas (LPG) tanks, compressed natural gas (CNG) tanks, hydrogen tanks and any other potentially explosive parts and components shall be neutralised;
(b)
oil filters;
(c)
refrigerants shall be treated in accordance with Regulation (EU) 2024/573;
(d)
components identified as containing mercury shall be separated during treatment into an identifiable stream, which shall be safely immobilised and disposed in accordance with Article 17 of Directive 2008/98/EC;
(e)
materials containing substances referred to in Article 5(4), which need to be labelled as laid down in Annex IV, shall be separated during treatment into an identifiable stream, which shall be safely immobilised and disposed in accordance with Article 17 of Directive 2008/98/EC.
All parts, components and materials collected during the depollution shall be stored in designated containers. The collection containers shall be labelled to indicate the components, parts and materials that are contained within them and stored in a secure location in compliance with Part A, in order to prevent accidental spillage, leakage or unauthorised access to it.
4.
The following information on the depollution of the end-of-life vehicles shall be recorded:
(a)
total number of treated end-of-life vehicles;
(b)
the average weight of the end-of-life vehicles before and after depollution and removal;
(c)
total quantity of each type of depolluted fluids, parts, components or materials;
(d)
name and contact details of the waste transporter, if applicable;
(e)
name and contact information of the final treatment site for the fluids and gases, parts, components or materials collected during the depollution process.
PART C
MANDATORY REMOVAL OF PARTS AND COMPONENTS FROM END-OF-LIFE VEHICLES
Exempted under Article 29(2), if the conditions of Part G of Annex VIII are met
X: the exemption applies
1.
Electric vehicle batteries, including their battery management systems, onboard chargers, casings or housings if present
2.
LMT batteries, as defined in Article 3, point (11), of Regulation (EU) 2023/1542, including their battery management systems, onboard chargers, casings or housings if present
3.
SLI batteries as defined in Article 3, point (12), of Regulation (EU) 2023/1542
4.
Portable batteries as defined in Article 3, point (9), of Regulation (EU) 2023/1542
5.
E-drive motors, including their casings and any associated control units, wiring, and other parts, components and materials
6.
Engine blocks
X
7.
Catalytic converters
8.
Gear boxes
X
9.
At least 70 % of the total glass from windshields, rear and side windows made of glass, including rooftop glass installations
10.
Rims
11.
Tyres
12.
Directly accessible parts of the infotainment system
13.
Head- and taillights, including their actuators
14.
Main wire harnesses
X
15.
Bumpers
X
16.
Fuel tanks
X
17.
Heat exchangers
X
18.
Parts of carbon fibre reinforced plastics
19.
Electrical and electronic components:
X
(a)
inverters and DC-DC converters of electric vehicles with a weight above 2 kilograms
X
(b)
easily accessible and large printed circuit boards
X
(c)
photo-voltaic (PV) panels with a surface area larger than 0,2 square metres
X
(d)
control modules and valve boxes for the automatic transmission
X
PART D
REUSE, REMANUFACTURING AND REFURBISHMENT OF PARTS AND COMPONENTS
1.
Technical evaluation of the removed parts and components:
(a)
For reuse:
(i)
the part or component is functional;
(ii)
it is fit to be used, in a readily manner, for its primary purpose it was conceived for;
(b)
For remanufacturing or refurbishment:
(i)
the part or component shall contain all relevant parts;
(ii)
it is fit to be remanufactured or refurbished, taking into account any damage, reduced functionality, reduced performance, reduced lifespan and repairs needed;
(iii)
there § is no apparent heavy corrosion impeding the functionality of the part or component.
2.
Minimum information to be provided in the labelling of the parts and components:
(a)
name of the component or part;
(b)
name, the postal address, indicating a single contact point and email address, a website, if applicable, identifying the authorised treatment facility that removed the component or part.
PART E
COMPONENTS AND PARTS NOT TO BE REUSED
1.
All airbags including cushions, pyrotechnic actuators, electronic control units and sensors.
2.
Emission after-treatment systems (e.g. catalytic converters, particulate filters) unless those parts comply with the related roadworthiness test laid down in Article 4 of Directive 2014/45/EU.
3.
Automatic or non-automatic seat belt assemblies, including webbing, buckles, retractors, pyrotechnic actuators.
4.
Seats in cases where they incorporate safety belt anchorages and/or airbags.
5.
Steering lock assemblies acting on the steering column.
6.
Immobilisers, including transponders and electronic control units.
PART F
SPECIFIC TREATMENT REQUIREMENTS OF THE REMOVED PARTS, COMPONENTS AND MATERIALS
1.
SLI Batteries shall be treated in accordance with Article 70 of Regulation (EU) 2023/1542.
2.
Electric vehicle batteries shall be treated in accordance with Article 70 of Regulation (EU) 2023/1542.
3.
LMT batteries shall be treated in accordance with Article 70 of Regulation (EU) 2023/1542.
4.
Portable batteries shall be treated in accordance with Article 70 of Regulation (EU) 2023/1542.
5.
Permanent magnet materials containing neodymium, dysprosium or praseodymium (Neodymium-Iron-Boron, NdFeB), as defined in Article 28 of Regulation (EU) 2024/1252, and copper from e-drive motors that are not suitable for reuse, remanufacturing or refurbishment, shall be removed where the process for removal is feasible to be performed by authorised treatment facilities without excessive cost. In case of lack of technical progress to recycle NdFeB permanent magnet materials, the e-drive motors or its permanent magnet material containing parts shall be stock-piled and labelled in accordance with Article 28(1), point (b), of Regulation (EU) 2024/1252. For the purpose of future recycling, the requirements related to the temporary storage of Directive 1999/31/EC shall not apply.
6.
Removed electronic components and parts, which are not subject for reuse, remanufacturing or refurbishment and non-ferrous fractions, including shredded printed circuit boards, shall be treated by treatment operators as specified in Article 8(3) of Directive 2012/19/EU.
7.
Removed glass from the end-of-life vehicle, as a minimum, shall be recycled into container glass, fibre glass, or equivalent quality.
8.
Removed refrigerants shall be recycled, reclaimed or destroyed in accordance with Article 8 of Regulation (EU) 2024/573.
9.
The plastics and residue fractions shall be handled in accordance with Article 7 of, and Annex IV to, Regulation (EU) 2019/1021.
10.
Rubber tyres shall be processed in accordance with the waste hierarchy and the general requirements laid down in Article 4 of Directive 2008/98/EC to prioritise prevention options that deliver the best overall environmental outcome including retreading, and prioritise recycling, including other methods than mechanical recycling, over energy recovery.
11.
Aluminium materials originating from heat exchangers as specified in Part C, point 17, of Annex VIII shall be stored and recycled separately from the cast and wrought aluminium fractions specified in Part G, point 2(b), of Annex VIII.
PART G
CRITERIA FOR COMBINED SHREDDING AND THE APPLICATION OF POST-SHREDDER TECHNOLOGIES
1.
In order to comply with Article 27(3) of this Regulation, end-of-life vehicles may be shredded together with other waste only if:
(a)
waste electrical and electronic equipment has been treated selectively in accordance with Annex VII to Directive 2012/19/EU;
(b)
all batteries have been removed in accordance with Regulation (EU) 2023/1542;
(c)
plastic packaging has been separated from packaging waste and metal packaging in accordance with Regulation (EU) 2025/40;
(d)
the combined shredding process does not lower the quality of waste streams compared to separate treatment; and
(e)
the specific contributions of each mixed waste stream to the output fractions can be identified as fulfilling the reporting obligations under Regulation (EU) 2023/1542, Regulation (EU) 2025/40, Directive 2008/98/EC and Directive 2012/19/EU.
2.
Quality requirements for the output fractions:
(a)
the total copper content of the main steel fraction shall not exceed 0,25 % on a weight basis; as from 1 September 2031, the total copper content of the main steel fraction shall not exceed 0,15 % on a weight basis;
(b)
by 1 September 2029, aluminium shall be sorted as a minimum into two fractions:
(i)
cast aluminium (fractions with a silicon content higher than 1,5 %);
(ii)
wrought aluminium (fractions with a silicon content equal or lower than 1,5 %);
(c)
by 1 September 2032, aluminium shall be sorted as a minimum into four fractions:
(i)
aluminium fraction with silicon content higher than 1,5 %, copper content equal or lower than 0,5 % and iron content equal or lower than 0,2 %;
(ii)
aluminium fraction with silicon content higher than 1,5 % and that does not meet the composition requirements of subpoint (i) for copper and iron;
(iii)
aluminium fraction with silicon content equal or lower than 1,5 %, magnesium equal or lower than 1,5 %, copper content equal or lower than 0,3 % and zinc content equal or lower than 0,3 %;
(iv)
aluminium fraction with silicon content equal or lower than 1,5 % and that does not meet the composition requirements of subpoint (iii) for magnesium, copper and zinc;
(d)
The shredder heavy fraction derived after air separation and separation of iron, shall be further treated with the aim to separate ferrous metals, non-ferrous metals, plastics and other organic materials for recycling or recovery. The residue of these processes shall contain less than 1 % of metal content by weight and, in accordance with Council Decision 2003/33/EC ( 1 ) , less than 5 % of total organic carbon by weight; the Total Organic Carbon (TOC) limit of < 5 % by weight does not apply if the shredder heavy fraction properly selected and reconditioned, is biologically stable according to current legislation;
(e)
the shredder light fraction shall be further treated with the aim to separate ferrous metals, non-ferrous metals, plastics and other organic materials for recycling or recovery; the residue of these processes shall contain less than 1 % of metal content by weight and, in accordance with Decision 2003/33/EC, less than 5 % of total organic carbon by weight; the Total Organic Carbon (TOC) limit of < 5 % by weight does not apply if the shredder light fraction, properly selected and reconditioned, is biologically stable, according to current legislation.
3.
Documentation to be provided for exemptions from the obligation to remove parts, components and materials:
(a)
where available, a copy of the written contract between the authorised treatment facility and the facility which performs the shredding operations and uses the post-shredding technologies, including the specifications on the quality of the secondary materials ready for recycling and the technical specification followed in processing treatment fractions from end-of-life vehicles;
(b)
a mass balance report of the sample analysis on the quality and quantity of the treatment fractions (output) for a representative treatment configuration provided by an independent body.
( 1 ) Council Decision 2003/33/EC of 19 December 2002 establishing criteria and procedures for the acceptance of waste at landfills pursuant to Article 16 of and Annex II to Directive 1999/31/EC ( OJ L 11, 16.1.2003, p. 27 , ELI: http://data.europa.eu/eli/dec/2003/33(1)/oj ).
INFORMATION FOR REGISTRATION IN THE REGISTER OF PRODUCERS
ANNEX IXSupplementary provisions
ANNEX IX
INFORMATION FOR REGISTRATION IN THE REGISTER OF PRODUCERS
1.
Information to be submitted by the producer or its authorised representative for extended producer responsibility:
(a)
name, and brand names if available, under which the producer operates in the Member State and address of the producer, including postal code and place, street and number, country, telephone number, if any, website and email address, indicating a single contact point;
(b)
national identification code of the producer, including its trade register number or equivalent official registration number and the European or national tax identification number;
(c)
categories of vehicles that the producer intends to make available on the market for the first time within the territory of a Member State;
(d)
information on how the producer meets its responsibilities laid down in Article 16, including information in written form on the following:
(i)
the measures put in place by the producer to fulfil the producer responsibility obligations laid down in Articles 16 and 20;
(ii)
the measures put in place to fulfil the collection obligation laid down in Article 23 with regard to the amount of vehicles the producer makes available on the market in the Member State; and
(iii)
the system to ensure that the data reported to the competent authorities are reliable;
(e)
a statement by the producer or, where applicable, producer’s authorised representative for the extended producer responsibility or producer responsibility organisation, stating that the information provided is true.
2.
Information to be provided, in addition to the information listed in point 1, where a producer responsibility organisation is appointed to carry out the extended producer responsibility obligations:
(a)
the name and contact details, including postal code and place, street and number, country, telephone number, web and email address and the national identification code of the producer responsibility organisation;
(b)
the trade register number or an equivalent official registration number and the European or national tax identification number of the producer responsibility organisation; and
(c)
the represented producer’s mandate.
3.
Information to be provided, in addition to the information listed in point 1 by the producer responsibility organisation where it has been appointed in accordance with Article 17(1):
(a)
the names and contact details, including postal codes and places, streets and numbers, countries, telephone numbers, websites and email addresses of the producers represented;
(b)
the mandate of each represented producer, where applicable;
(c)
where the producer responsibility organisation represents more than one producer, it shall indicate separately how each one of the represented producers meets the responsibilities set out in Article 16.
4.
Where obligations under Article 16 are fulfilled on a producer’s behalf by an appointed representative for the extended producer responsibility that represents more than one producer, that representative shall, in addition to the information listed in point 1, provide the name and the contact details for each of the represented producers separately.
CERTIFICATE OF DESTRUCTION
ANNEX XSupplementary provisions
ANNEX X
CERTIFICATE OF DESTRUCTION
1.
The establishment or undertaking issuing this certificate
1.1
Name
1.2
Address
1.3
Phone number
1.4
Email [if available]
1.5
Registration or identification number ( *1 )
2.
Competent authority who issued a permit for the establishment or undertaking referred to in point 1
2.1
Member State
2.2
Name
2.3
Address
3.
Certificate of destruction
3.1
Date of issue
3.2
Number
4.
Information on the vehicle this certificate of destruction is issued for
4.1
Nationality mark
4.2
(A)
Registration number ( *2 )
4.3
(J)
Category ( *2 )
4.4
(D.1) Make ( *2 )
4.5
(D.3) Commercial name ( *2 )
4.6
(E)
Vehicle Identification Number ( *2 )
4.7
Number of registration certificate
5.
Information on the owner of the vehicle
5.1
(C.2.1) Surname or business name ( *2 )
5.2
(C.2.2) Other name(s) ( *2 )
5.3
(C.2.3) Address ( *2 )
5.4
Phone number [if available and upon consent of the owner]
5.5
Email [if available and upon consent of the owner]
6
Remarks
( *1 ) This requirement may be waived in the case where the national registration or identification system does not provide for such number.
( *2 ) Harmonised community codes as referred to in Directive 1999/37/EC.
AMENDMENTS TO REGULATION (EU) 2018/858 AND REGULATION (EU) No 168/2013
ANNEX XISupplementary provisions
ANNEX XI
AMENDMENTS TO REGULATION (EU) 2018/858 AND REGULATION (EU) No 168/2013
1.
Annex II to Regulation (EU) 2018/858 is amended as follows:
(a)
in Part I, entry G13 is replaced by the following:
‘G13
Circularity
Regulation (EU) 2026/1738
X
X
X
X
X
X
X
X
X
X’
(b)
Appendix 1 is amended as follows:
(i)
in Table 1, entry G13 is replaced by the following:
‘G13
Circularity
Regulation (EU) 2026/1738
n/a However, Part E of Annex VIII on prohibition of reuse of the specified component parts shall apply.’
(ii)
in Table 2, entry G13 is replaced by the following:
‘G13
Circularity
Regulation (EU) 2026/1738
n/a However, Part E of Annex VIII on prohibition of reuse of the specified component parts shall apply.’
(c)
in Appendix 2, point 4 is amended as follows:
(i)
in the table ‘Part I: Vehicles belonging to category M 1 ’, entry 59 is replaced by the following:
‘59
Regulation (EU) 2026/1738 (Circularity)
The requirements of that Regulation shall not apply.’
(ii)
in the table ‘Part II: Vehicles belonging to category N 1 ’, entry 59 is replaced by the following:
‘59
Regulation (EU) 2026/1738 (Circularity)
The requirements of that Regulation shall not apply.’
(d)
Part III is amended as follows:
(i)
in Appendix 1, entry 59 is replaced by the following:
‘59
Circularity
Regulation (EU) 2026/1738
N/A
N/A’
(ii)
in Appendix 2, entry 59 is replaced by the following:
‘59
Circularity
Regulation (EU) 2026/1738
N/A
N/A’
(iii)
in Appendix 3, entry 59 is replaced by the following:
‘59
Circularity
Regulation (EU) 2026/1738
N/A’
(iv)
in Appendix 4, entry 59 is replaced by the following:
‘59
Circularity
Regulation (EU) 2026/1738
N/A
N/A’
2.
Annex II to Regulation (EU) No 168/2013 is amended as follows:
In Section C1 of the table, entry 15a is replaced by the following:
L1e-A 1
L1e-B 2
L2e
L3e
L4e
L5e-B
L6e-A
L7e-A1
L7e-A2
L7e-B1
L7e-B2
‘15a
18
Circularity requirements
Regulation (EU) 2026/1738
x
x
x
x
x
x
x
x
x
x
x ’
AMENDMENTS TO REGULATION (EU) 2023/1542
ANNEX XIISupplementary provisions
ANNEX XII
AMENDMENTS TO REGULATION (EU) 2023/1542
The table in Annex I is replaced with the following table:
‘Column 1
Designation of the substance or group of substances
Column 2
Conditions of restriction
1.
Mercury CAS No 7439-97-6 EC No 231-106-7 and its compounds
Batteries, whether or not present in and incorporated into appliances, light means of transport or other vehicles, shall not contain more than 0,0005 % of mercury (expressed as mercury metal) by weight.
2.
Cadmium CAS No 7440-43-9 EC No 231-152-8 and its compounds
1.
Portable batteries, whether or not present in and incorporated into appliances, light means of transport or other vehicles, shall not contain more than 0,002 % of cadmium (expressed as cadmium metal) by weight.
2.
Electric vehicle and SLI batteries, incorporated in vehicles, including special purpose vehicles, of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858 shall not contain more than 0,01 % of cadmium (expressed as cadmium metal) by weight in homogeneous material.
3.
Point 2 shall not apply to electric vehicle batteries used as spare parts for electric vehicles, including special purpose vehicles, of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858 placed on the market before 31 December 2008.
3.
Lead CAS No 7439-92-1 EC No 231-100-4 and its compounds
1.
From 18 August 2024, portable batteries, whether or not present in and incorporated into appliances, shall not contain more than 0,01 % of lead (expressed as lead metal) by weight.
2.
The restriction set out in point 1 shall not apply to portable zinc-air button cells until 18 August 2028.
3.
Portable batteries incorporated in vehicles, including special purpose vehicles, of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858, shall not contain more than 0,1 % of lead (expressed as lead metal) by weight in homogeneous material.
4.
Point 3 shall not apply to Portable Batteries incorporated in, or used as spare parts for, vehicles, including special purpose vehicles, of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858, type approved before 1 January 2024.
5.
Electric vehicle batteries incorporated in vehicles, including special purpose vehicles, of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858, shall not contain more than 0,1 % of lead (expressed as lead metal) by weight in homogeneous material.
6.
Point 5 shall not apply to:
(a)
electric vehicle batteries used in high voltage systems ( 2 ) incorporated in, or used as spare part for, in vehicles of the categories M 1 and N 1 , as defined in Regulation (EU) 2018/858 and type approved before 1 January 2019;
(b)
electric vehicle batteries not covered by point (a) of this point incorporated in or used as spare part for vehicles, including special purpose vehicles, of the categories M 1 and N 1 , as defined in Regulation (EU) 2018/858, and type approved before 1 January 2024.
7.
SLI batteries incorporated in vehicles, including special purpose vehicles, of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858, shall not contain more than 0,1 % of lead (expressed as lead metal) by weight in homogeneous material.
8.
Point 7 shall not apply to:
(a)
SLI batteries used in 12 V applications for vehicles, including special purpose vehicles, of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858 ( 3 ) ;
(b)
SLI batteries used in 24 V applications in special purpose vehicles of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858 ( 4 ) ;
(c)
SLI batteries used in other applications than those covered by points (a) and (b) of this point in vehicles, including special purpose vehicles, of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858 that are type approved before 1 January 2024.
4.
Hexavalent chromium CAS No 18540-29-9EC No 606-053-1 and its compounds
Batteries incorporated in vehicles, including special purpose vehicles, of the categories M 1 and N 1 as defined in Regulation (EU) 2018/858, shall not contain more than 0,1 % of hexavalent chromium, expressed as hexavalent chromium metal, by weight in homogeneous material.
( 1 ) Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits ( OJ L 96, 29.3.2014, p. 357 , ELI: http://data.europa.eu/eli/dir/2014/35/oj ).
( 2 ) Systems that have a voltage of > 75 V DC as provided for in Article 1 of Directive 2014/35/EU of the European Parliament and of the Council ( 1 ) .’.
( 3 ) This exemption shall be reviewed in 2030.
( 4 ) This exemption shall be reviewed in 2030.
( 1 ) Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits ( OJ L 96, 29.3.2014, p. 357 , ELI: http://data.europa.eu/eli/dir/2014/35/oj ).
( 3 ) This exemption shall be reviewed in 2030.
( 4 ) This exemption shall be reviewed in 2030.
CRITERIA TO BE FULFILLED BY INSTALLATIONS IN THIRD COUNTRIES CARRYING OUT PRODUCTION OF RECYCLED MATERIAL
ANNEX XIIISupplementary provisions
ANNEX XIII
CRITERIA TO BE FULFILLED BY INSTALLATIONS IN THIRD COUNTRIES CARRYING OUT PRODUCTION OF RECYCLED MATERIAL
PART A CRITERIA TO DEMONSTRATE THAT RECYCLED MATERIAL HAS BEEN PRODUCED IN AN INSTALLATION THAT MEETS CERTAIN REQUIREMENTS FOR THE PROTECTION OF HUMAN HEALTH, CLIMATE AND ENVIRONMENT SET OUT IN UNION LAW OR EQUIVALENT TO THOSE REQUIREMENTS (IN ACCORDANCE WITH ARTICLE 6(4))
1.
The installation located in a third country involved in the production of recycled material shall fulfil the following conditions in its actual operations:
(a)
it complies with the requirements to recycle waste and carries out its activities in accordance with the applicable national legislation on environmental protection;
(b)
it is designed, constructed and operated in a safe and environmentally sound manner and, in particular, it has the required processes, appropriate waste management technology, organisation and infrastructure in place to recycle the waste in question;
(c)
it sources its plastic waste from a Member State or a country which complies with Union law or equivalent standards as the Member States in terms of protection of the environment and the safety of workers and operates in such a country in accordance with the criteria defined in paragraph 3;
(d)
it establishes and operates management and monitoring systems, procedures and techniques that have the purpose of preventing, reducing, minimising and to the extent practicable eliminating:
(i)
health and safety risks to workers concerned and to the population in the vicinity of the facility; and
(ii)
adverse effects on the environment caused by its activities (in particular through adequate measures taken to monitor and address pollution);
(e)
it ensures the traceability of all waste received and treated at the facility, including ensuring that all residual waste generated from its activities are documented and are only transferred to waste management facilities that are authorised to treat such residual waste;
(f)
it has taken measures designed to save energy and limit the emissions of greenhouse gases linked to its activities;
(g)
it establishes and is able to provide records of its waste management activities for the last five years; if an installation has operated for less than five years, it establishes and is able to provide records of its waste management activities for the time it has operated;
(h)
its operator or the management thereof have not been convicted of having carried out illegal activities linked to waste management in the last five years.
2.
The following or equivalent rules shall be taken into account, as a point of reference and where relevant:
(a)
specific requirements for the treatment of certain waste and on the calculation of the quantity of waste treated, which are mandatory under Union legislation, and on the accounting of the quantities of recycled materials produced;
(b)
the Best Available Techniques conclusions adopted for certain activities under Directive 2010/75/EU.
3.
The plastic waste shall be treated in a manner according to requirements set out in Union law or equivalent to those requirements and shall come from a Member State or country with a comprehensive waste management framework covering its entire territory and demonstrating its ability and willingness to guarantee environmentally sound waste management, taking into account in particular the following criteria:
(a)
the measures implemented and planned to ensure the environmentally sound management of waste within its territory, such as the introduction of an extended producer responsibility scheme or an equivalent system implementing the polluter pays principle;
(b)
the measures implemented and planned to increase the proportion of post-consumer plastic recycled from vehicles, and the indicators for monitoring these measures;
(c)
the measures implemented and planned to increase the proportion of post-consumer recycled plastic incorporated in vehicles placed on the national market, and the indicators for monitoring these measures.
PART B CRITERIA TO DEMONSTRATE THAT RECYCLED MATERIAL HAS BEEN PRODUCED IN COMPLIANCE WITH THE REQUIREMENTS IN ARTICLE 6(1), (2) AND (3)
The installation located in a third country involved in the production of recycled material shall fulfil the following conditions in its actual operations:
1.
The installation shall be able to provide evidence that it is producing materials recycled from post-consumer waste. If the installation is also producing materials derived from pre-consumer waste or derived from raw materials, it shall be able to demonstrate that it clearly distinguishes between the different types of materials. The installation shall ensure that it is only supplying materials recycled from post-consumer waste, as a condition for this material to be accounted for as part of the targets set out in Article 6;
2.
An installation producing recycled materials from post-consumer waste derived from end-of-life vehicles or repaired vehicles shall be able to demonstrate that such waste has been collected separately and was not mixed with materials from other origins in such a way that would prevent traceability of this waste before its arrival on the installation and during the whole recycling process.
REQUIREMENTS FOR AUDITS, CERTIFIERS AND AUDITORS
ANNEX XIVSupplementary provisions
ANNEX XIV
REQUIREMENTS FOR AUDITS, CERTIFIERS AND AUDITORS
PART A DETAILED REQUIREMENTS FOR THIRD PARTIES CONDUCTING AUDITS
1.
A third party conducting audits of the installation located in a third country in accordance with Article 6(5) shall be independent of the supplier, manufacturer or the person involved in the production of the recycled material and of the controlled installation. To that end, the third party shall be able to document that:
(a)
it is not part of or under the control of these entities;
(b)
it has established and operates procedures guaranteeing its impartiality, including:
(i)
assessment of risks of its impartiality on an ongoing basis;
(ii)
identification, elimination and mitigation of risks to impartiality resulting from financial, commercial and other types of pressure;
(iii)
assessment of risk of its impartiality resulting from relationships of its personnel;
(c)
it is structured and managed in a way ensuring its independence and impartially, including:
(i)
it is clearly identifiable within the legal entity, if the legal entity conducts also activities not related to audits;
(ii)
it has reporting rules on the performed audit activity;
(iii)
its personnel has clearly identifiable responsibilities with respect to conducting audits.
2.
A third party conducting audits in accordance with Article 6(5) shall be considered to have appropriate qualifications in the area of audits and waste treatment if it has a sufficient number of qualified personnel, directly or via subcontracting, that is regularly trained and if its personnel involved in conducting such audits has documented professional experience in all of the following areas:
(a)
conducting audits of facilities treating waste;
(b)
waste treatment operations;
(c)
environmental and occupational health and safety management systems;
(d)
production of recycled material.
3.
In order to demonstrate compliance with the criteria referred to in points 1 and 2 of this Part, the third party that conducts an audit or certification shall refer to its certification with Union or equivalent internationally recognised standards relevant for the conduct of audits, such as international standard ISO 19011:2018 or ISO/IEC 17020:2012.
PART B. SUBJECT OF THE AUDIT
1.
The audit referred to in Article 6(5) shall verify that the installation located in a third country involved in the production of recycled material fulfils the conditions listed in Annex XIII in its actual operations.
2.
The names and contact details of the individuals who carried out the audits shall be clearly indicated in the audit reports.
CORRELATION TABLES
ANNEX XVSupplementary provisions
ANNEX XV
CORRELATION TABLES
1. Directive 2000/53/EC
Directive 2000/53/EC
This Regulation
Article 1
Article 1
Article 2, point (1)
Article 3, point (1)
Article 2, point (2)
Article 3, point (2)
Article 2, point (3)
Article 3, point (23)
Article 2, point (4)
Article 3, point (39)
Article 2, point (5)
Article 3, point (18)
Article 2, point (6)
Article 3, point (4)
Article 2, point (7)
Article 3, point (39)
Article 2, point (8)
Article 3, point (39)
Article 2, point (9)
Article 3, point (39)
Article 2, point (10)
Article 3, point (35)
Article 2, point (11)
—
Article 2, point (11) (a)
—
Article 2, point (11) (b)
—
Article 2, point (11) (c)
—
Article 2, point (11) (d)
—
Article 2, point (12)
—
Article 2, point (13)
—
Article 3(1)
Article 2(1), point (a)
Article 3(2)
—
Article 3(3)
—
Article 3(4)
—
Article 3(5)
—
Article 4(1), point (a)
Article 5(1)
Article 4(1), point (b)
Article 7(1)
Article 4(1), point (c)
Article 6
Article 4(2), point (a)
Article 5(4) and (5)
Article 4(2), point (b)(i)
Article 5(6), point (a)
Article 4(2), point (b)(ii)
Article 5(6), point (b)
Article 4(2), point (b)(iii)
Article 5(6), point (c)
Article 4(2), point (b)(iv)
Article 5(6), point (d)
Article 4(2), point (c)
—
Article 5(1), first dash
—
Article 5(1), second dash
Article 23(3), point (b)
Article 5(2)
Article 24(1)
Article 5(3), first subparagraph
Article 25
Article 5(3), second subparagraph
Article 25(1)
Article 5(3), third subparagraph
—
Article 5(4), first subparagraph
Article 24(2)
Article 5(4), second subparagraph
Article 16 and Article 20(1), point (a)
Article 5(4), third subparagraph
Article 24(2)
Article 5(4), fourth subparagraph
—
Article 5(5), first subparagraph
Article 25(1) and Annex X
Article 5(5), second subparagraph
—
Article 6(1)
Article 26(1) and (2)
Article 6(2), first subparagraph
Article 15(1)
Article 6(2), second subparagraph
—
Article 6(3), first subparagraph
Article 29(1) and Annex VIII, Part C
Article 6(3), second subparagraph
Article 28(1)
Article 6(4)
Article 15(2)
Article 6(5)
Article 26(4)
Article 6(6)
Article 26(3)
Article 7(1)
Article 30(1)
Article 7(2), point (a)
—
Article 7(2), point (b)
Article 33(1), points (a) and (b)
Article 7(2), second subparagraph
—
Article 7(2), third subparagraph
—
Article 7(3)
—
Article 7(4)
—
Article 7(5)
—
Article 8(1)
Article 12(1)
Article 8(2)
Article 12(2)
Article 8(3)
Article 11(1)
Article 8(4)
Article 11(1) and (3)
Article 9(1a), first subparagraph
Article 50(1), first subparagraph
Article 9(1a), second subparagraph
Article 50(1) second subparagraph
Article 9(1a), third subparagraph
Article 50(1) third subparagraph
Article 9(1b)
Article 50(2)
Article 9(1c)
Article 50 (3), third subparagraph
Article 9(1d)
Article 50(5)
Article 9(2)
Article 9 and Annex V, Part A
Article 9a(1)
Article 51(1)
Article 9a(2)
Article 51(2)
Article 9a(3)
Article 51(3)
Article 9a(4)
Article 51(4)
Article 9a(5)
Article 51(5)
Article 9a(6)
Article 51(6)
Article 10(1)
—
Article 10(2)
—
Article 10(3)
—
Article 10a
Article 56
Article 11(1)
Article 52(1)
Article 11(2)
Article 52(2)
Article 12(1)
Article 59(1)
Article 12(2)
Article 59(2)
Article 12(3)
—
Article 13
—
Annex I
Annex VIII
Annex II
Annex IV
2. Directive 2005/64/EC
Directive 2005/64/EC
This Regulation
Article 1, first subparagraph
Article 1
Article 1, second subparagraph
—
Article 2
Article 2(1), point (a)
Article 3, point (a)
—
Article 3, point (b)
—
Article 3, point (c)
Article 2(2), point (a)
Article 4, point (1)
Article 3, point (1)
Article 4, point (2)
—
Article 4, point (3)
Article 3, point (3)
Article 4, point (4)
Article 3, point (2)
Article 4, point (5)
Annex III
Article 4, point (6)
—
Article 4, point (7)
Article 3, point (40)
Article 4, point (8)
—
Article 4, point (9)
Article 3, point (4)
Article 4, point (10)
Article 3, point (39)
Article 4, point (11)
—
Article 4, point (12)
Article 3, point (39)
Article 4, point (13)
Article 3, point (5)
Article 4, point (14)
Article 3, point (6)
Article 4, point (15)
Article 3, point (7)
Article 4, point (16)
—
Article 4, point (17)
—
Article 4, point (18)
—
Article 4, point (19)
—
Article 4, point (20)
—
Article 5(1)
—
Article 5(2)
Article 8(2)
Article 5(3)
Article 8(3)
Article 5(4)
—
Article 6(1)
—
Article 6(2), second subparagraph
Article 5(4) and (5)
Article 6(3)
Article 9
Article 6(4)
—
Article 6(5)
—
Article 6(6)
—
Article 6(7)
—
Article 6(8)
—
Article 7, point (a)
Annex VIII, Part E
Article 7, point (b)
Annex VIII, Part E
Article 8
—
Article 9
—
Article 10(1)
—
Article 10(2)
—
Article 10(3)
—
Article 10(4)
—
Article 11(1)
—
Article 11(2)
—
Article 12
—
Article 13
—
Annex I
Article 4(1)
Annex II
—
Annex III
—
Annex VII
—
Annex V
Annex VIII, Part E
Annex VI
—
Source: EUR-Lex (Publications Office of the EU), © European Union, reuse permitted under Commission Decision 2011/833/EU.
