Commission Implementing Decision (EU) 2024/1434 of 24 May 2024 authorising grading methods for the classification of pig carcasses in Poland and repealing Decision 2005/240/EC (notified under document C(2024) 3342)

• CELEX: Implementing Decision (EU) 2024/1434
• Articles: 6

Article 1

The use of the following grading methods is authorised for the assessment of the lean meat content of pig carcasses pursuant to Section B.IV, point 1, of Annex IV to Regulation (EU) No 1308/2013 in Poland:

(a)

the ‘Capteur Gras/Maigre – Sydel (CGM)’ apparatus and the assessment methods related thereto, details of which are given in Part I of the Annex;

(b)

the ‘Ultra FOM 300’ apparatus and the assessment methods related thereto, details of which are given in Part II of the Annex;

(c)

the ‘IM-03’ apparatus and the assessment methods related thereto, details of which are given in Part III of the Annex;

(d)

the ‘Autofom III’ apparatus and the assessment methods related thereto, details of which are given in Part IV of the Annex;

(e)

the ‘Autofom IV’ apparatus and the assessment methods related thereto, details of which are given in Part V of the Annex;

(f)

the ‘Fat-O-Meater II (FOM II)’ apparatus and the assessment methods related thereto, details of which are given in Part VI of the Annex;

(g)

the ‘manual method (ZP)’ and the assessment methods related thereto, details of which are given in Part VII of the Annex;

(h)

the ‘CSB Image-Meater 2.0’ apparatus and the assessment methods related thereto, details of which are given in Part VIII of the Annex;

(i)

the ‘EstiMeat Expert’ apparatus and the assessment methods related thereto, details of which are given in Part IX of the Annex;

(j)

the ‘EstiMeat Pro’ apparatus and the assessment methods related thereto, details of which are given in Part X of the Annex.

As regards the apparatus ‘Ultra FOM 300’ referred to in the first paragraph, point (b), after the end of the measurement procedure it must be possible to verify on the carcass that the apparatus measured the values of measurement X1 and X3 on the site provided for in the Annex, Part II, point 3. The corresponding marking of the measurement site must be made at the same time as the measurement procedure.

The manual method (ZP), referred to in the first paragraph, point (g), shall only be authorised for abattoirs having a slaughter line with a capacity to process no more than 40 pigs per hour.

Article 2

Notwithstanding the standard presentation referred to in Section B.III of Annex IV to Regulation (EU) No 1308/2013, the flare fat, the kidneys and the diaphragm need not be removed from pig carcasses before being weighed and graded whereas the external auditory canal may be removed. In order to establish quotations for pig carcasses on a comparable basis, the recorded hot weight shall be:

(a)

reduced:

(i)

for diaphragm by 0,23 %;

(ii)

for flare fat and kidneys by:

—

1,90 % for carcasses grade S and E,

—

2,11 % for carcasses grade U,

—

2,54 % for carcasses grade R,

—

3,12 % for carcasses grade O,

—

3,35 % for carcasses grade P;

(b)

increased by 260 grams per carcass for both external auditory canals.

Article 3

Modifications of the authorised grading methods or apparatuses thereof referred to in Article 1 shall be authorised by Commission Implementing Decision.

Article 4

Decision 2005/240/EC is repealed.

Article 5

This Decision is addressed to the Republic of Poland.

It shall apply from 29 July 2024.

Schedules & Appendices

ANNEX

ANNEX

GRADING METHODS FOR THE CLASSIFICATION OF PIG CARCASSES IN POLAND

PART I

Capteur Gras/Maigre – Sydel (CGM)

1.

The rules provided for in this Part shall apply when the grading of pig carcasses is carried out by means of the apparatus known as ‘Capteur Gras/Maigre – Sydel (CGM)’.

2.

The apparatus shall be equipped with a high-definition Sydel probe 8 mm in width, a light-emitting infra-red diode (Honeywell) and two light sensors (Honeywell). The operating distance is between 0 and 105 mm. The values measured will be converted into estimated lean meat content by the CGM itself.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 60,7538 – 0,6465 × X1 + 0,1243 × X2

Where:

Y

=

the estimated lean meat percentage,

X1

=

the thickness of the back fat measured at the third to fourth rib from last rib position, 60 mm from the dorsal midline, measured parallel to the split line of the carcass,

X2

=

the thickness of the lumbar muscle measured at the third to fourth rib from the last rib position, 60 mm from the dorsal midline, measured parallel to the split line of the carcass.

This formula shall be valid for carcasses weighing between 60 and 120 kg.

PART II

Ultra FOM 300

1.

The rules provided for in this Part shall apply when the grading of pig carcasses is carried out by means of the apparatus known as ‘Ultra FOM 300’.

2.

The apparatus shall be equipped with an ultrasonic transducer array at 3,5 MHz (U-Systems). The results of the measurements shall be converted into estimated lean meat content by means of the Ultra FOM 300 apparatus itself.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 64,0655 – 0,5986 × X1 + 0,0584 × X2 – 0,1600 × X3 + 0,0275 × X4

Where:

Y

=

the estimated lean meat percentage,

X1

=

the thickness of the back fat measured at the last rib position, measured at the same time, in the same place and in the same way as X2,

X2

=

the thickness of the lumbar muscle measured at the last rib position, 70 mm from the dorsal midline perpendicularly to the muscle,

X3

=

the thickness of the back fat measured at the third to fourth rib from the last rib position, measured at the same time, in the same place and in the same way as X4,

X4

=

the thickness of the lumbar muscle measured at the third to fourth rib from the last rib position, 70 mm from the dorsal midline perpendicularly to the muscle.

This formula shall be valid for carcasses weighing between 60 and 120 kg.

PART III

IM-03

1.

The rules provided for in this Part shall apply when the grading of pig carcasses is carried out by means of the apparatus known as ‘IM-03’.

2.

The apparatus shall be equipped with a needle-optical probe (single line scanner SLS01) of 7 mm diameter. The probe contains the line of contact image sensors (CIS) and green light-emitting diodes. The operating distance is between 0 and 132 mm.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 57,3864 – 0,5657 × X1 + 0,1476 × X2

Where:

Y

=

the estimated lean meat percentage,

X1

=

the thickness of the back fat measured at the third to fourth rib from the last rib position, 60 mm from the dorsal midline, measured parallel to the split line of the carcass,

X2

=

the thickness of the lumbar muscle measured at the third to fourth rib from the last rib position, 60 mm from the dorsal midline, measured parallel to the split line of the carcass,

This formula shall be valid for carcasses weighing between 60 and 120 kg.

PART IV

Autofom III

1.

The rules provided for in this Part shall apply when the classification of pig carcasses is carried out by means of the apparatus ‘Autofom III’.

2.

The apparatus shall be equipped with sixteen 2 MHz ultrasonic transducers (Carometec A/S), with an operating distance between transducers of 25 mm. The ultrasonic data shall comprise measurements of back fat thickness, muscle thickness and related parameters. The results of the measurements shall be converted into estimates of the percentage of lean meat by using a computer.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 59,9912 – 0,3658 × X1 – 0,3841 × X2 + 0,0605 × X3 + 0,0602 × X4

Where:

Y

=

the estimated lean meat percentage,

X1

=

the thickness of the back fat (without skin) at the MFT2 position,

X2

=

the thickness of the back fat (without skin) at the MFT1 position,

X3

=

the thickness of the lumbar muscle at the MFT2 position,

X4

=

the thickness of the lumbar muscle at the MFT1 position.

The MFT refers to the position of the minimum fat thickness (without skin). MFT1 refers to the minimum fat thickness in the entire carcass and MFT2 refers to the minimum fat thickness in the lumbar closest to the bottom of the array.

This formula shall be valid for carcasses weighing between 60 and 120 kg.

PART V

Autofom IV

1.

The rules provided for in this Part shall apply when the classification of pig carcasses is carried out by means of the apparatus ‘Autofom IV’.

2.

The apparatus shall be equipped with 16 2 MHz ultrasonic transducers (Carometec A/S), with an operating distance between transducers of 25 mm. The ultrasonic data shall comprise measurements of back fat thickness, muscle thickness and related parameters. The results of the measurements shall be converted into estimates of the percentage of lean meat by using a computer.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 56,3590 – 0,7618 × X1 + 0,0326 x X2 + 0,0685 × X3 + 0,0551 × X4 + 0,3868 × X5

Where:

Y

=

the estimated lean meat percentage,

X1

=

the thickness of the back fat (without skin) measured 70 mm from the spine at the MFT2 position,

X2

=

the thickness of the lumbar muscle at the MFT2 position,

X3

=

the maximum thickness of the lumbar muscle of the entire carcass,

X4

=

the thickness of the lumbar muscle at the MFT1 position,

X5

=

the thickness of the back fat (without skin) at the MFT2 position.

The MFT refers to the position of the minimum fat thickness (without skin). MFT1 refers to the minimum fat thickness in the entire carcass and MFT2 refers to the minimum fat thickness in the lumbar closest to the bottom of the array.

This formula shall be valid for carcasses weighing between 60 and 120 kg.

PART VI

Fat-O-Meater II (FOM II)

1.

The rules provided for in this Part shall apply when the classification of pig carcasses is carried out by means of the apparatus ‘Fat-O-Meater II (FOM II)’.

2.

The apparatus is a new version of the Fat-O-Meater measurement system. The FOM II consists of an optical probe with a knife, a thickness measurement device having a measurement thickness of 125 mm and a data acquisition and analysis board – Carometec Touch Panel i15 computer (Ingress Protection IP69K). The results of the measurements are converted into estimated lean meat content by means of a computer.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 60,3281 – 0,6493 × X1 + 0,1529 × X2

Where:

Y

=

the estimated lean meat percentage,

X1

=

the thickness of the back fat measured at the third to fourth rib from the last rib position, 70 mm from the dorsal midline perpendicularly to the lumbar muscle,

X2

=

the thickness of the lumbar muscle measured at the third to fourth rib from the last rib position, 70 mm from the dorsal midline perpendicularly to the muscle.

This formula shall be valid for carcasses weighing between 60 and 120 kg.

PART VII

Manual method (ZP)

1.

The rules provided for in this Part shall apply when the grading of pig carcasses is carried out by use of the ‘manual method (ZP)’ measuring by ruler.

2.

This method may be implemented using a ruler, with the grading determined on the basis of the prediction equation. It is based on the manual measurement on the midline of the split carcass of the thickness of the back fat and of the thickness of the lumbar muscle.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 62,4306 – 0,6264 × X1 + 0,0911 × X2

Where:

Y

=

the estimated lean meat percentage,

X1

=

the minimum thickness of visible fat on the midline of the split carcass in mm, covering the M. gluteus medius ,

X2

=

the thickness of the lumbar muscle in mm on the midline of the split carcass, measured as the shortest connection between the front (cranial) end of the M. gluteus medius and the upper (dorsal) edge of the vertebral canal.

This formula shall be valid for carcasses weighing between 60 and 120 kg.

PART VIII

CSB Image-Meater 2.0

1.

The rules provided for in this Part shall apply when the classification of pig carcasses is carried out by means of the apparatus ‘CSB Image-Meater 2.0’.

2.

The CSB Image-Meater 2.0 consists of a video camera, a PC equipped with an image-analysis card, a screen, a printer, a command mechanism, a trigger mechanism and interfaces. The 5 Image-Meater variables are all measured at the split line in the ham area (around M. gluteus medius ). The results of the measurements shall be converted into estimates of the percentage of lean meat by using a computer.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 56,4264 + 0,1417 × X1 – 0,4331 × X2 – 0,3504 × X3 + 0,9952 × X4

Where:

X1

=

the thickness in mm of the M. gluteus medius at the front (cranial) end,

X2

=

mean averaged thickness in mm of the back fat over M. gluteus medius ,

X3

=

mean averaged thickness in mm of the back fat over the vertebral bodies a, b, c, and d,

X4

=

mean averaged thickness in mm of the external layer of the back fat over the vertebral bodies a, b, c, and d.

This formula shall be valid for carcasses weighing between 60 and 120 kg.

PART IX

EstiMeat Expert

1.

The rules provided for in this Part shall apply when the classification of pig carcasses is carried out by means of the apparatus ‘EstiMeat Expert’.

2.

The EstiMeat Expert apparatus consists in a depth camera that captures 3D images of the carcasses into a point cloud data, and a computer equipped with software, based on a neural model, to process the point cloud data. The images obtained are processed by the software and the output is a vector containing several thousand features.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 58,8209 + X1619 × 0,1035 + X2201 × 0,0311 + X2234 × 0,3665 + X2293 × 0,1774 + X2313 × –0,3141 + X2363 × –0,0715 + X2377 × –0,5151 + X2425 × 0,0360 + X2457 × 0,0245 + X2499 × 0,1272 + X2517 × –0,3138 + X2592 × –0,0177 + X2641 × 0,0853 + X2643 × 0,0915 + X2711 × 0,2308 + X2805 × 0,0598 + X2897 × 0,0727 + X3088 × 0,1598 + X3225 × 0,0305 + X3317 × 0,1003 + X3449 × 0,0572 + X3481 × –0,0646 + X3486 × 0,0147 + X3497 × –0,3797 + X3573 × 0,0357 + X3643 × 0,1213 + X3779 × 0,1753 + X3788 × –0,0265 + X3829 × 0,0559 + X3878 × –0,1215 + X4377 × 0,0896 + X4411 × –0,0141 + X4473 × 0,0210 + X4597 × 0,0413 + X4612 × –0,1083 + X4633 × 0,1482

Where the sequence X1619 to X4633 are the features obtained as described in point 2 and selected on the basis of a statistical analysis carried out during the authorisation trial.

This formula shall be valid for carcasses weighing between 60 and 120 kg.

PART X

EstiMeat Pro

1.

The rules provided for in this Part shall apply when the classification of pig carcasses is carried out by means of the apparatus ‘EstiMeat Pro’.

2.

The EstiMeat Pro apparatus consists in a depth camera that captures 3D images of the carcasses into a point cloud data, and a computer equipped with software, based on a neural model, to process the point cloud data. The images obtained are processed by the software and the output is a vector containing several thousand features.

3.

The lean meat content of the carcass shall be calculated in accordance with the following formula:

Y = 58,7239 + X1035 × 0,4758 + X1083 × –0,3372 + X1228 × 0,2446 + X1312 × 0,8333 + X1358 × –0,0403 + X1484 × 0,0297 + X2059 × –0,1927 + X2131 × 0,9101 + X2169 × –0,2740 + X2201 × –0,6023 + X2293 × 0,7966 + X2315 × –0,3573 + X2336 × 0,7383 + X2425 × –0,0186 + X2549 × –0,4582 + X2974 × 1,4175 + X3083 × –0,5134 + X3131 × –0,3641 + X3193 × –0,3497 + X3201 × 0,3780 + X3225 × –0,0341 + X3317 × 0,3329 + X3339 × –0,4669 + X3360 × 0,6139 + X3387 × –0,3666 + X3409 × –0,1408 + X3481 × –0,0379 + X3486 × 0,2139 + X3497 × –0,4410 + X3532 × –0,6743 + X3573 × 0,2748 + X4291 × 0,4108 + X4341 × –0,4624 + X4363 × 0,7046 + X4433 × 0,4170 + X4473 × 0,2388 + X4532 × –0,0327 + X4597 × 0,2930

Where the sequence X1035 to X4597 are the features obtained as described in point 2 and selected on the basis of a statistical analysis carried out during the authorisation trial.

This formula shall be valid for carcasses weighing between 60 and 120 kg.