ANNEX ISupplementary provisions
ANNEX I Templates for the information document and information folder LIST OF APPENDICES Appendix Number Appendix title Page 1 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a tailpipe pollution-control system 59 2 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a crankcase and evaporative emissions system 62 3 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an on-board diagnostic (OBD) system 64 4 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a sound level system 68 5 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a propulsion unit performance system 70 6 Model information document relating to EU type-approval of a pollution-control device as a STU 72 7 Model information document relating to EU type-approval of a noise-abatement device as a STU 76 8 Model information document relating to EU type-approval of an exhaust (pollution-control device and noise-abatement device) as a STU 78 9 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a braking system 82 10 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of lighting and light-signalling devices system 85 11 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) a roll-over protective structure (ROPS) system 87 12 Model information document relating to EU type-approval of a type of (or a type of a vehicle with regard to) an installation of tyres system 89 13 Model information document relating to EU type-approval of an audible warning device as a component 92 14 Model information document relating to EU type-approval of a non-glazing front windscreen as a component/STU 94 15 Model information document relating to EU type-approval of a windscreen washer device as a component/STU 96 16 Model information document relating to EU type-approval of a rearward visibility device as a component/STU 98 17 Model information document relating to EU type-approval of safety belts as a STU 100 18 Model information document relating to EU type-approval of a seating position (saddle/seat) as a component/STU) 102 19 Model information document relating to EU type-approval of a trailer coupling device as a STU 104 20 Model information document relating to EU type-approval of devices to prevent unauthorised use as a STU 106 21 Model information document relating to EU type-approval of passenger handholds as a STU 108 22 Model information document relating to EU type-approval of footrests as a STU 110 23 Model information document relating to EU type-approval of a side-car as a STU 111 24 Manufacturer’s declaration for vehicles capable of converting their performance level from subcategory (L3e/L4e)-A2 to (L3e/L4e)-A3 and vice-versa 120 25 Manufacturer’s declaration on powertrain tampering prevention measures (anti-tampering) 123 PART A INFORMATION FOLDER 1. General requirements 1.1. When applying for EU type-approval for a vehicle, system, component or separate technical unit, the manufacturer shall provide, in accordance with Article 27 of Regulation (EU) No 168/2013, an information folder which shall contain the following: 1.1.1. a list of contents; 1.1.2. the information on the type-approval procedure chosen in accordance with Article 25(1) of Regulation (EU) No 168/2013, the template for which is set out in point 2 (information folder sheet); 1.1.3. the information document as set out in Part B of this Annex; 1.1.4. all relevant data, drawings, photographs and other information as required in the information document; 1.1.5. the manufacturer’s statement on endurance of functional safety-critical systems, parts and equipment as referred to in Article 22(2) of Regulation (EU) No 168/2013 and set out in Annex II to this regulation; 1.1.6. the manufacturer’s statement on vehicle structure integrity as referred to in Article 22(5) of Regulation (EU) No 168/2013 and in point 1.1.of Annex XIX to Commission Delegated Regulation (EU) No 3/2014 of 24 October 2013 supplementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to vehicle functional safety requirements for the approval of two- or three-wheel vehicles and quadricycles ( 1 ) , as set out point 1.4. of Annex II to this regulation; 1.1.7. the manufacturer’s certificate providing proof of compliance to the type-approval authority on access to vehicle on-board diagnostic (OBD) systems and to vehicle repair and maintenance information as referred to in Article 57(8) of Regulation (EU) No 168/2013 and set out in Annex III to this regulation; 1.1.8. the manufacturer’s declaration of conversion of (L3e/L4e)-A2 to (L3e/L4e)-A3 motorcycle characteristics and vice versa as referred to in Article 25(8) of Regulation (EU) No 168/2013 and in point 4.2.6. of Annex III to Commission Delegated Regulation (EU) No 44/2014 of 21 November 2013 supplementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to the vehicle construction and general requirements for the approval of two- or three- wheel vehicles and quadricycles ( 2 ) , as set out in Appendix 24 of this Annex; 1.1.9. the manufacturer’s declaration on powertrain tampering prevention measures (anti-tampering) as referred to in Article 20(2) of Regulation (EU) No 168/2013 and in points 2.2., 2.6. and 5.2. of Annex II to Commission Delegated Regulation 44/2014 according to the models established in Appendix 25 of this Annex; 1.1.10. any additional information requested by the approval authority as part of the approval procedure. 1.2. Applications submitted on paper shall be in triplicate. Any drawings shall be to an appropriate scale and in sufficient detail on size A4 sheets or in a folder of A4 format. Photographs, if any, shall show sufficient detail. 1.3. If the systems, components or separate technical units have electronic controls, information concerning their performance shall be provided. 2. Template of the information folder sheet Information on the type-approval procedure chosen in accordance with Article 25(1) of Regulation (EU) No 168/2013 Information folder sheet A duly completed version of this statement shall be included in the information folder. The undersigned: [… (full name and position)] Company name and address of the manufacturer: … Name and address of the manufacturer’s representative (if any): … Hereby applies for type-approval procedure (4) : (a) step-by-step type-approval (b) single-step type-approval (c) mixed type-approval Where procedures (a) or (c) are chosen, compliance with requirements as under (b) is declared for all systems, components and separate technical units. Multi-stage type-approval chosen in accordance with Article 25(5) of Regulation (EU) No 168/2013: yes/no (4) Information on the vehicle(s) to be filled in, if application is for EU whole-vehicle type-approval (3) : 0.1. Make (trade name of the manufacturer): … 0.2. Type (17) : … 0.2.1. Variant(s) (17) : … 0.2.2. Version(s) (17) : … 0.2.3. Commercial name(s) (if available): … 0.3. Category, subcategory and sub-subcategory of vehicle (2) : … Information to be filled in, if application is for type-approval of a system/ component/separate technical unit (3)(4) : 0.7. Make(s) (trade name(s) of manufacturer): … 0.8. Type: … 0.8.1. Commercial name(s) (if available): … 1.6. Virtual and/or self-testing (3) 1.6.1. Overview list with virtual and/or self-tested systems, components or separate technical units pursuant to point 6 of Annex III to Commission Delegated Regulation (EU) No 44/2014 below: Overview table virtual and/or self-testing Delegated act Annex Subject Virtual and/or self-tested: yes/no (4) Commission Delegated Regulation (EU) No 134/2014 ( *1 ) IX Testing procedures on maximum design vehicle speed Self-testing: yes/no (4) Commission Delegated Regulation (EU) No 3/2014 II Audible warning devices Self-testing: yes/no (4) Commission Delegated Regulation (EU) No 3/2014 VIII Driver-operated controls including identification of controls, tell-tales and indicators Self-testing: yes/no (4) Commission Delegated Regulation (EU) No 3/2014 IX Installation of lighting and light- signalling devices Virtual testing: yes/no (4) Commission Delegated Regulation (EU) No 3/2014 X Rearward visibility Virtual testing: yes/no (4) Commission Delegated Regulation (EU) No 3/2014 XIV Installation of tyres Virtual testing: yes/no (4) Commission Delegated Regulation (EU) No 44/2014 XIV Registration plate space Self & Virtual testing: yes/no (4) Commission Delegated Regulation (EU) No 44/2014 XVI Stands Self-testing: yes/no (4) This Commission Implementing Regulation VIII Statutory plate and EU type-approval mark Self-testing: yes/no (4) 1.6.2. Detailed report on validation of virtual and/or self-testing added: yes/no (4) Place: … Date: … Signature: … Name and position in the company: … PART B INFORMATION DOCUMENT 1. General requirements 1.1. The information document shall have a reference number supplied by the applicant. 1.2. Where the particulars appearing in the information document for vehicle approval have changed, the manufacturer shall submit revised pages to the approval authority showing clearly the nature of the change(s) and the date of re-issue. 1.3. Type-approval numbers 1.3.1. The manufacturer shall supply the information required by the following table in respect of the applicable subjects for the vehicle in Annex II to Regulation (EU) No 168/2013. All relevant approvals and test reports (if available) for each subject shall be included. However, information in respect of systems, components or separate technical units need not be given here so long as such information is included in the correspondent approval certificate. Type-approval number and test report overview Item number and subject Type-approval number or test report number ( *4 ) Date of issue of the type-approval or of its extension or of the test report Member State or contracting party ( *2 ) issuing the type- approval ( *3 ) or technical service issuing the test report ( *4 ) Reference to the regulatory act and its latest amendment Variant(s)/ version(s e.g. B1 audible warning devices Signed: … Position in company: … Date: … 2. Content of the information document All information documents shall contain the following: 2.1. For a whole vehicle type-approval the manufacturer shall complete: — the matrix in point 2.3. to identify the versions and variants of the vehicle intended for type-approval; — a list of items applicable to the (sub-)category and to the technical characteristics of the vehicle from which content has been extracted, adhering to the numbering system of the total list set out in point 2.6. 2.2. For a system, component or separate technical unit as listed in table 1 the manufacturer shall complete the applicable appendix to this Annex. In addition to the Annexes mentioned in table 1, the systems, components and separate technical units shall comply with the following requirements: — arrangements for type-approval procedures (Annex III of Commission Delegated Regulation (EU) No 44/2014) — conformity of production (CoP) (Annex IV of Delegated Regulation (EU) No 44/2014) — access to repair and maintenance information (Annex XV of Delegated Regulation (EU) No 44/2014) Table 1 Lists of systems, components and separate technical units which may be subject to an EU type-approval LIST I — Environmental and propulsion unit performance requirements Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) No 134/2014 Annex number As amended by and/or at the stage of implementation 1 System: tailpipe pollution-control system II, III, V, VI 2 System: crankcase and evaporative emissions IV, V 3 System: environmental and functional on-board diagnostic (OBD) VIII (and Annex XII to Commission Delegated Regulation (EU) No 44/2014) 4 System: sound level IX 5 System: propulsion unit performance X 6 STU: pollution-control device II, III, IV, V, VI 7 STU: noise-abatement device IX 8 STU: exhaust device (pollution-control device and noise-abatement device) II, III, V, VI, IX LIST II — Vehicle functional safety requirements Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) No 3/2014 Annex number As amended by and/or at the stage of implementation 9 System: braking III 10 System: installation of lighting and light-signalling devices IX 11 System: Roll-over protective structure (ROPS) XI 12 System: installation of tyres XV 13 Component: audible warning device II 14 Component/STU: non-glazing front windscreen VII 15 Component/STU: windscreen washer device VII 16 Component/STU: rearward visibility device X 17 STU: safety belts XII 18 Component/STU: seating position (saddle/seat) XIII LIST III — Vehicle construction and general type-approval requirements Appendix System or component/separate technical unit (STU) Commission Delegated Regulation (EU) No 44/2014 Annex number As amended by and/or at the stage of implementation 19 STU: trailer coupling device V 20 STU: devices to prevent unauthorised use VI 21 STU: passenger handholds XIII 22 STU: footrests XIII 23 STU: side-car VIII, XI, XIII; (and Annexes III, V, VII, IX, X, XII, XIII, XIV, XV, XVII and XIX to Commission Delegated Regulation (EU) No 3/2014) 2.3. Matrix showing the combinations of the entries listed in point 2.6. within the versions and variants of the vehicle type Variants and version matrix Item No All Version 1 Version 2 Version 3 Version n 2.3.1. A separate matrix shall be compiled for each variant within the type. 2.3.2. Entries with no restrictions on their combination within a variant shall be listed in the column headed ‘All’. 2.3.3. The above information may be presented in an alternative format or merged with the information supplied under point 2.6. 2.4. Type-, variant- and version designations 2.4.1. The manufacturer shall allocate an alphanumeric code to each vehicle type, variant and version, made up of Roman letters and/or Arabic numerals, which shall also be indicated in the certificate of conformity (see Annex IV) of the vehicle concerned. The use of brackets and hyphens is permitted provided they do not replace a letter or a numeral. 2.4.2. The whole code shall be designated: Type-Variant-Version or ‘TVV’. 2.4.3. The TVV shall clearly and unequivocally identify a unique combination of technical features in relation to the criteria defined in Part B of this Annex. 2.4.4. The same manufacturer may use the same code in order to define a vehicle type when the latter falls in two or more categories. 2.4.5. The same manufacturer shall not use the same code in order to define a vehicle type for more than one type-approval within the same vehicle category. 2.4.6. Number of characters for the TVV 2.4.6.1. The number of characters shall not exceed: a. 15 for the code of the vehicle type; b. 25 for the code of one variant; c. 35 for the code of one version. 2.4.6.2. The complete alphanumeric ‘TVV’ shall not contain more than 75 characters. 2.4.6.3. When the TVV is used as a whole, a space shall be left between the type, the variant and the version. Example of such TVV: 159AF[… space]0054[… space]977K(BE). 2.5. For those subjects referred to in Annex II to Regulation (EU) No 168/2013 whose approvals have been granted in accordance with the UNECE regulations referred to in Article 54 of Regulation (EU) 168/2013 (UNECE approvals), the manufacturer shall supply the information required in point 2.7. only if it is not already provided in the correspondent approval certificate and/or test report. However, the information referred to in the certificate of conformity (Annex IV) shall be supplied in any case. 2.6. The manufacturer shall complete the applicable item numbers of the template set out in point 2.8. and submit this filled-out list to the approval authority that grants the type-approval, split into two separate documents. The applicable items marked with * shall remain with the approval authority that grants the type-approval and all other applicable items shall make part of the information folder. The Colum ‘(Sub) categories’ indicates to which sub-categories applies each particular entry (e.g. ‘L1e - L7e’ means that the entry applies to all categories and subcategories). 2.7. The following type of data entries may be omitted in the information document under the condition that an appropriate technical drawing either as a paper document or a pdf-file is added to the information folder and on which these listed items are shown in a clear and readable way: 2.7.1. Make (with the exemption of Item No 0.1); 2.7.2. Type (with the exemption of Item No 0.2); 2.7.3. Location / where; 2.7.4. Working principle (with the exemption of Item No 3.2.1.2); 2.7.5. Characteristics; 2.7.6. Number of (with the exemption of Items No 1.3., 3.2.1.1. and 6.16.1.); 2.7.7. Identification / part number; 2.7.8. (Brief) / (Technical) description; 2.7.9. Design; 2.7.10. Schematic drawing / diagram; 2.7.11. (Construction) materials used; 2.7.12. Angles / inclination and other dimensions (height, length, width, distance) (with the exemption of Items No 2.2.1., 2.2.2., 2.2.3., 2.2.17., 7.6.1. and 7.6.2.); 2.7.13. Tolerance; 2.7.14. Reference mark; 2.7.15. Size (with the exemption of point 6.18.1.1.1., 6.18.1.1.2. and 6.18.1.1.3.); 2.7.16. Configuration; 2.8. INFORMATION DOCUMENT DATA ENTRIES Item No. (Sub) categories Detailed information 0. GENERAL INFORMATION A. General information concerning vehicles 0.1. L1e — L7e Make (trade name of manufacturer) : … 0.2. L1e — L7e Type (17) : … 0.2.1 L1e — L7e Variant(s) (17) : … 0.2.2 L1e — L7e Version(s) (17) : … 0.2.3. L1e — L7e Commercial name(s) (if available): … 0.3. L1e — L7e Category, subcategory and sub-subcategory of vehicle (2) : … 0.4. L1e — L7e Company name and address of manufacturer : … 0.4.1. L1e — L7e Name(s) and address(es) of assembly plants: … 0.4.2. L1e — L7e Name and address of manufacturer’s authorised representative, if any: … 0.5. L1e — L7e Manufacturer’s statutory plate(s) : … 0.5.1. L1e — L7e Location of the manufacturer's statutory plate (15)(18) : … 0.5.2. L1e — L7e Method of attachment: … 0.5.3. L1e — L7e Photographs and/or drawings of the statutory plate (completed example with dimensions): … 0.6. L1e — L7e Location of the vehicle identification number (15) : … 0.6.1. L1e — L7e Photographs and/or drawings of the locations of the vehicle identification number (completed example with dimensions): … 0.6.1.1. L1e — L7e The serial number of the type begins with: … B. General information concerning systems, components or separate technical units 0.7. L1e — L7e Make(s) (trade name(s) of manufacturer) : … 0.8. L1e — L7e Type : … 0.8.1. L1e — L7e Commercial name(s) (if available): … 0.8.2. L1e — L7e Type-approval number(s) (if available): … 0.8.3. L1e — L7e Type-approval(s) issued on (date, if available): … 0.9. L1e — L7e Company name and address of manufacturer : … 0.9.1. L1e — L7e Name(s) and address(es) of assembly plants: … 0.9.2. L1e — L7e Name and address of manufacturer’s authorised representative, if any: … 0.10. Vehicle(s) for which the system/separate technical unit is intended for (21) : … 0.10.1. L1e — L7e Type (17) : … 0.10.2. L1e — L7e Variant (17) : … 0.10.3. L1e — L7e Version (17) : … 0.10.4. L1e — L7e Commercial name(s) (if available): … 0.10.5. L1e — L7e Category, subcategory and sub-subcategory of vehicle (2) : … 0.11. L1e — L7e Type-approval marks for components and separate technical units (19) : … 0.11.1. L1e — L7e Method of attachment: … 0.11.2. L1e — L7e Photographs and/or drawings of the location of the type-approval mark (completed example with dimensions): … C. General information regarding conformity of production and access to repair and maintenance information 0.12. Conformity of production 0.12.1. L1e — L7e Description of overall quality-assurance management systems. 0.13. Access to repair and maintenance information 0.13.1. L1e — L7e Address of principal website for access to vehicle repair and maintenance information: … 0.13.2. L1e — L7e In the case of multi-stage type-approval, address of principal website for access to vehicle repair and maintenance information from manufacturer(s) at previous stage(s): 1. GENERAL CONSTRUCTION CHARACTERISTICS 1.1. L1e — L7e Photographs and/or drawings of a representative vehicle: … 1.2. L1e — L7e Scale drawing of the whole vehicle: … 1.3. L1e — L7e Number of axles and wheels: … 1.3.1. L1e — L7e Axles with twinned wheels (23) : … 1.3.2. L1e — L7e Powered axles (23) : … 1.4. L1e — L7e Chassis (if any) (overall drawing): … 1.5. L2e, L5e-B, L6e-B, L7e-A2, L7e-B2, L7e-C Material used for the bodywork: 1.6. L1e — L7e Position and arrangement of the propulsion(s): … 1.7. L4e, L5e-B, L6e-B, L7e-A2, L7e-B2, L7e-C Hand of drive: left/right/centre (4) : … 1.7.1. L1e — L7e Vehicle is equipped to be driven in right/left-hand traffic and in countries that use metric/metric and imperial units. (4) : … 1.8. Propulsion unit performance 1.8.1. L3e, L4e, L5e, L7e-A, L7e-B2 Declared maximum vehicle speed: … km/h 1.8.2. L1e, L2e, L6e, L7e-B1, L7e-C Maximum design vehicle speed (22) : … km/h and gear in which it is reached: … 1.8.3. L1e — L7e Maximum net power combustion engine: … kW at … min -1 at A/F ratio: … 1.8.4. L1e — L7e Maximum net torque combustion engine: … Nm at … min -1 at A/F ratio: … 1.8.5. L1e — L7e Maximum continuous-rated power electric motor (15/30 (4) minutes power (27) ): … kW at … min -1 1.8.6. L1e — L7e Maximum continuous-rated torque electric motor: … Nm at … min -1 1.8.7. L1e — L7e Maximum continuous total power for propulsion(s): … kW at … min -1 at A/F ratio: … 1.8.8. L1e — L7e Maximum continuous total torque for propulsion(s): … Nm at … min -1 at A/F ratio: … 1.8.9. L1e — L7e Maximum peak power for propulsion(s): … kW at … min -1 at A/F ratio: … 2. MASSES AND DIMENSIONS (in kg and mm.) refer to drawings where applicable 2.1 Range of vehicle mass (overall) 2.1.1. L1e — L7e Mass in running order: … kg 2.1.1.1. L1e — L7e Distribution of mass in running order between the axles: … kg 2.1.2. L1e — L7e Actual mass: … kg 2.1.2.1. L1e — L7e Distribution of actual mass between the axles: … kg 2.1.3. L1e — L7e Technically permissible maximum laden mass: … kg 2.1.3.1. L1e — L7e Technically permissible maximum mass on front axle: … kg 2.1.3.2. L1e — L7e Technically permissible maximum mass on rear axle: … kg 2.1.3.3. L4e Technically permissible maximum mass on sidecar axle: … kg 2.1.4. L1e — L7e Maximum hill-starting ability at the maximum technically permissible mass declared by the manufacturer: … % slope 2.1.5. L1e — L7e Maximum pay mass declared by manufacturer: … kg 2.1.6. L1e — L7e Safe load carrying capacity of load platform declared by manufacturer: … kg 2.1.7. L1e — L7e Technically permissible maximum towable mass in case of (4) : Braked: … kg Unbraked: … kg 2.1.7.1 L1e — L7e Technically permissible maximum laden mass of the combination: … kg 2.1.7.2. L1e — L7e Technically permissible maximum mass at the coupling point: … kg 2.1.8. L1e — L7e Mass of the optional equipment: … kg 2.1.9. L1e — L7e Mass of the superstructure: … kg 2.1.10. L1e — L7e Mass of the propulsion battery: … kg 2.1.11. L2e, L4e, L5e, L6e, L7e Mass of the doors: … kg 2.1.12. L2e-U, L5e-B, L6e-BU, L7e-CU Mass of the machines or equipment installed on the load platform area: … kg 2.1.13. L1e — L7e Mass of the gaseous fuel system as well as storage tanks for gaseous fuel: … kg 2.1.14. L1e — L7e Mass of the storage tanks to store compressed air: … kg 2.2. Range of vehicle dimensions (overall) 2.2.1. L1e — L7e Length: … mm 2.2.2. L1e — L7e Width: … mm 2.2.3. L1e — L7e Height: … mm 2.2.4. L1e — L7e Wheelbase: … mm 2.2.4.1. L4e Wheelbase sidecar (28) : … mm 2.2.5. Track width 2.2.5.1. L1e — L7e if equipped with twinned wheels L2e, L4e, L5e, L6e, L7e Track width front: … mm. 2.2.5.2. L1e — L7e if equipped with twinned wheels Track width rear: … mm. 2.2.5.3. L2e, L4e, L5e, L6e, L7e Track width sidecar: … mm. 2.2.6. L7e-B Front overhang: … mm. 2.2.7. L7e-B Rear overhang: … mm. 2.2.8. Load platform dimensions 2.2.8.1. L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CU Length of the load platform: … mm 2.2.8.2. L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CU Width of load platform: … mm 2.2.8.3. L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CU Height of load platform: … mm 2.2.9. Centre of gravity 2.2.9.1. L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CU Location of the centre of gravity forward of the rear axle Lcg: … mm. 2.2.9.2. L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CU Location of the centre of gravity above the ground plane Hcg: … mm. 2.2.9.3. L2e-U, L5e-B, L6e-BU, L7e-B2, L7e-CU Location centre of gravity of loaded platform forward of the rear axle LcgLP: … mm. 2.2.10. Miscellaneous dimensions 2.2.10.1. L7e-B2 Approach angle (11) : … degrees. 2.2.10.2. L7e-B2 Departure angle (11) : … degrees. 2.2.10.3. L7e-B2 Ramp angle (11) : … degrees. 2.2.10.4. L7e-B2 Ground clearance under the front axle (11) : … mm. 2.2.10.5. L7e-B2 Ground clearance under the rear axle (11) : … mm. 2.2.10.6. L3e-AxE (x=1, 2 or 3), L3e-AxT (x=1, 2 or 3) L7e-B Ground clearance between the axles (11) : … mm. 2.2.10.7. L7e-B Wheelbase to ground clearance ratio … [no unit] 2.2.10.8. L7e-B2 Static stability coefficient — Kst: … [no unit] 2.2.10.9. L3e-AxE, L3e-AxT Seat height: … mm 2.2.10.10. L3e-AxE, L3e-AxT Ground clearance: … mm 3. GENERAL POWERTRAIN CHARACTERISTICS 3.1 Manufacturer of the propulsion unit 3.1.1. Combustion engine 3.1.1.1. L1e — L7e Manufacturer: … 3.1.1.2. L1e — L7e Engine code (as marked on the engine or other means of identification): … 3.1.1.3. L1e — L7e Fuel identification marking (if available): … 3.1.2. Electric motor 3.1.2.1. L1e — L7e Manufacturer: … 3.1.2.2. L1e — L7e Electric motor code (as marked on the engine or other means of identification): … 3.1.3. Hybrid application 3.1.3.1. L1e — L7e Manufacturer: … 3.1.3.2. L1e — L7e Application code (as marked on the engine or other means of identification): … 3.1.3.3. L1e — L7e Fuel identification marking (if available): … 3.1.3.4. L1e — L7e Photographs and/or drawings of the location of the code(s) and/or type-approval numbers (completed example with dimensions) (20) : … 3.2. Combustion engine 3.2.1. Specific engine information 3.2.1.1. L1e — L7e Number of combustion engines: … 3.2.1.2. L1e — L7e Working principle: internal combustion engine (ICE)/positive ignition/compression ignition /external combustion engine (ECE)/turbine/compressed air (4) : … 3.2.1.3. L1e — L7e Cycle: four-stroke/two-stroke/rotary/other (4) : … 3.2.1.4. L1e — L7e Cylinders 3.2.1.4.1. L1e — L7e Number: … 3.2.1.4.2. L1e — L7e Arrangement (26) : … 3.2.1.4.3. L1e — L7e Bore (12) : … mm 3.2.1.4.4. L1e — L7e Stroke (12) : … mm 3.2.1.4.5. L1e — L7e Number and configuration of stators in the case of rotary-piston engine: … 3.2.1.4.6. L1e — L7e Volume of combustion chambers in the case of rotary-piston engine: … cm 3 3.2.1.4.7. L1e — L7e Firing order: … 3.2.1.5. L1e — L7e Engine capacity (6) : … cm 3 3.2.1.6. L1e — L7e Volumetric compression ratio (7) : … 3.2.1.7. L1e — L7e Number of inlet and exhaust valves * 3.2.1.7.1. L1e — L7e Number and minimum cross-sectional areas of inlet and outlet ports: … * 3.2.1.7.2. L1e — L7e Valve timing or equivalent data: … * 3.2.1.7.3. L1e — L7e Maximum lift of valves, angles of opening and closing, or timing details of alternative distribution systems, in relation to dead centres. For variable timing system, minimum and maximum timing: … * 3.2.1.7.4. L1e — L7e Reference and/or setting ranges (4) : … 3.2.1.8. L1e — L7e Drawings of combustion chamber, cylinder head, piston, piston rings: … 3.2.1.9. L1e — L7e Normal warm engine idling speed: … min -1 3.2.1.10. L1e — L7e Stop-start system: yes/no (4) * 3.2.2. Powertrain/propulsion/drive-train management system 3.2.2.1. L1e — L7e PCUs/ECUs (4) software identification number(s): … and calibration verification number(s): … 3.2.3. Fuel 3.2.3.1. L1e — L7e Fuel type: (9) 3.2.3.2. L1e — L7e Vehicle fuel configuration: mono-fuel/bi- fuel/flex fuel (4) 3.2.3.2.1. L1e — L7e Maximum amount of bio-fuel acceptable in fuel: … % by volume 3.2.4. Fuel pressure delivery and control 3.2.4.1. L1e — L7e Brief description and schematic drawing of low-and/or high-pressure fuelling wet system(s) (4) : … 3.2.4.2. L1e — L7e Low- and/or high-pressure fuel pump(s): yes/no (4) 3.2.4.2.1. L1e — L7e Fuel pump control: mechanical/on/off electric/continuous operation/electronically controlled variable operation (4) : … 3.2.4.2.2. L1e — L7e For CI combustion engines and dual fuel engines only maximum fuel delivery (4)(7) : … g/s or mm 3 /stroke or cycle at an engine speed of:…min -1 or, alternatively, a characteristic diagram: … (When boost control is supplied, state the characteristic fuel delivery and boost pressure versus engine speed) 3.2.4.3. L1e — L7e Common rail: yes/no (4) 3.2.4.4. L1e — L7e Fuel distributor/rail/hoses (4) : yes/no (4) 3.2.4.5. L1e — L7e Fuel pressure and/or fuel flow regulator(s): yes/no (4) 3.2.5. Fuel mass metering and control 3.2.5.1. L1e — L7e By carburettor(s): yes/no (4) * 3.2.5.1.1. L1e — L7e Operating principle and construction: … * 3.2.5.1.2. L1e — L7e Maximum fuel-flow rate: … g/s at maximum power and torque: … 3.2.5.1.3. L1e — L7e Carburettor(s) settings (7) : … * 3.2.5.1.4. L1e — L7e Carburettor diffusers: … * 3.2.5.1.5. L1e — L7e Carburettor fuel-level in float chamber: … * 3.2.5.1.5.1. L1e — L7e Carburettor mass of float: … 3.2.5.1.6. L1e — L7e Carburettor cold-starting system: manual/automatic (4) : yes/no (4) 3.2.5.1.6.1. L1e — L7e Carburettor cold-starting system operating principle(s): … 3.2.5.1.7. L1e — L7e Mixture scavenging port: yes/no (4) 3.2.5.1.7.1. L1e — L7e Mixture scavenging port dimensions: … 3.2.5.2. L1e — L7e By mechanically/hydraulically controlled fuel injection (4) : yes/no (4) 3.2.5.2.1. L1e — L7e Operation principle: … 3.2.5.2.2. L1e — L7e Mechanical/electronic (4) adjustment of maximum fuel mass delivery: yes/no (4) 3.2.5.3. L1e — L7e By electronically controlled fuel injection system: yes/no (4) 3.2.5.3.1. L1e — L7e Operation principle: port injection/direct injection/pre-chamber/swirl chamber (4) : … 3.2.5.3.2. L1e — L7e Fuel injector(s): single-/multi-point/direct injection/other (specify) (4) : … 3.2.5.3.3. L1e — L7e Total and per cylinder amount of fuel injectors: … 3.2.5.4. L1e — L7e Air-assisted fuel injector: yes/no (4) : … 3.2.5.4.1. L1e — L7e Description and operating pressure of air-assist: … 3.2.5.5. L1e — L7e Cold start system: yes/no (4) 3.2.5.5.1. L1e — L7e Description of cold start system: … 3.2.5.6. L1e — L7e Auxiliary starting aid: yes/no (4) 3.2.5.7. L1e — L7e CI injection specific: yes/no 3.2.5.7.1. L1e — L7e Static injection timing (7) : … 3.2.5.7.2. L1e — L7e Injection advance curve (7) : … 3.2.6. Gaseous fuelling system and control 3.2.6.1. L1e — L7e Brief description and schematic drawing of gaseous fuelling system(s): … 3.2.6.2. L1e — L7e Liquefied petroleum gas (LPG) fuelling system: yes/no (4) 3.2.6.2.1. L1e — L7e Type-approval number according to UNECE Regulation No 67 ( 3 ) : … 3.2.6.2.2. L1e — L7e Electronic engine management control unit for LPG fuelling: yes/no (4) 3.2.6.2.2.1. L1e — L7e Emission-related adjustment possibilities: … 3.2.6.2.3. L1e — L7e Further documentation: … * 3.2.6.2.3.1 L1e — L7e Description of the safeguarding of the catalyst at switch-over from petrol to LPG or back: … 3.2.6.2.3.2 L1e — L7e System layout (electrical connections, vacuum connections, compensation hoses, etc.): … 3.2.6.2.4. L1e — L7e Drawing of the symbol: … 3.2.6.3. L1e — L7e Natural gas (NG) fuelling system: yes/no (4) 3.2.6.3.1. L1e — L7e Type-approval number according to UNECE Regulation No 110 ( 4 ) : … 3.2.6.3.2. L1e — L7e Electronic engine management-control unit for NG fuelling: yes/no (4) 3.2.6.3.2.1. L1e — L7e Emission-related adjustment possibilities: … 3.2.6.3.3.. L1e — L7e Further documentation: … * 3.2.6.3.3.1. L1e — L7e Description of the safeguarding of the catalyst at switch-over from petrol to NG or back: … 3.2.6.3.3.2. L1e — L7e System layout (electrical connections, vacuum connections compensation hoses, etc.): … 3.2.6.3.4. L1e — L7e Drawing of the symbol: … 3.2.6.4. L1e — L7e Gaseous fuel: LPG/NG-H/NG-L/NG-HL (4) : yes/no (4) 3.2.6.4.1. L1e — L7e Pressure regulator(s) or vaporiser/pressure regulator(s) (4) * 3.2.6.4.1.1. L1e — L7e Number of pressure reduction stages: … 3.2.6.4.1.2. L1e — L7e Pressure in final stage, minimum: … kPa — maximum: … kPa 3.2.6.4.1.3. L1e — L7e Number of main adjustment points: … 3.2.6.4.1.4. L1e — L7e Number of idle adjustment points: … 3.2.6.4.1.5. L1e — L7e Type-approval number: … 3.2.6.4.2. L1e — L7e Fuelling system: mixing unit/gas injection/liquid injection/direct injection (4) * 3.2.6.4.2.1. L1e — L7e Mixture strength regulation: … 3.2.6.4.2.2. L1e — L7e System description and/or diagram and drawings: … 3.2.6.4.2.3. L1e — L7e Type-approval number: … 3.2.6.4.3. L1e — L7e Mixing unit: yes/no (4) 3.2.6.4.3.1. L1e — L7e Number: … 3.2.6.4.3.2. L1e — L7e Location: … 3.2.6.4.3.3. L1e — L7e Adjustment possibilities: … 3.2.6.4.3.4. L1e — L7e Type-approval number: … 3.2.6.4.4. L1e — L7e Inlet manifold injection: yes/no (4) 3.2.6.4.4.1. L1e — L7e Injection: single-point/multi-point (4) 3.2.6.4.4.2. L1e — L7e Injection: continuous/simultaneously timed/sequentially timed (4) 3.2.6.4.5. L1e — L7e Injection equipment: yes/no (4) 3.2.6.4.5.1. L1e — L7e Adjustment possibilities: … 3.2.6.4.5.2. L1e — L7e Type-approval number: … 3.2.6.4.6. L1e — L7e Supply pump: yes/no (4) 3.2.6.4.6.1. L1e — L7e Type-approval number: … 3.2.6.4.7. L1e — L7e Injector(s): … 3.2.6.4.7.1. L1e — L7e Type-approval number: … 3.2.6.4.8. L1e — L7e Direct/port injection: yes/no (4) 3.2.6.4.9. L1e — L7e Injection pump/pressure regulator: yes/no (4) 3.2.6.4.9.1. L1e — L7e Type-approval number: … 3.2.6.4.10. L1e — L7e Separate electronic control unit (ECU) for gaseous fuelling system: yes/no (4) 3.2.6.4.10.1. L1e — L7e Adjustment possibilities: … 3.2.6.4.10.2. L1e — L7e Software identification number(s): … 3.2.6.4.10.3. L1e — L7e Calibration verification number(s): … 3.2.6.5. L1e — L7e NG fuel-specific equipment: … 3.2.6.5.1. L1e — L7e Variant 1 (only in the case of approvals of engines for several specific fuel compositions): … 3.2.6.5.2. L1e — L7e Fuel composition: Overview methane (CH 4 ): basis: …%mole min. …%mole max. …%mole ethane (C 2 H 6 ): basis: …%mole min. …%mole max. …%mole propane (C 3 H 8 ): basis: …%mole min. …%mole max. …%mole butane (C 4 H 10 ): basis: …%mole min. …%mole max. …%mole C 5 /C 5 +: basis: …%mole min. …%mole max. …%mole oxygen (O 2 ): basis: …%mole min. …%mole max. …%mole inert (N 2 , He, etc.): basis: …%mole min. …%mole max. …%mole 3.2.6.5.3. L1e — L7e Gaseous fuel injector(s): … 3.2.6.5.4. L1e — L7e Variant 2 (only in the case of approvals for several specific fuel compositions): … 3.2.6.6. L1e — L7e Hydrogen fuel-specific equipment: yes/no (4) 3.2.6.6.1. L1e — L7e EC type-approval number according to Regulation (EC) No 79/2009 of the European Parliament and of the Council ( 5 ) : … * 3.2.6.6.2. L1e — L7e Further documentation 3.2.6.6.3. L1e — L7e System layout (electrical connections, vacuum connections, compensation hoses, etc.): … * 3.2.6.6.4. L1e — L7e Description of the safeguarding of the catalyst at switch-over from petrol to hydrogen/H 2 NG (4) or back: … 3.2.6.6.5. L1e — L7e Drawing of the symbol: … 3.2.6.7. L1e — L7e H 2 NG fuelling system: yes/no (4) 3.2.6.7.1. L1e — L7e Percentage of hydrogen in the fuel (the maximum specified by the manufacturer): … 3.2.7. Air-induction system 3.2.7.1. L1e — L7e Brief description and schematic drawing of gaseous intake air-flow and induction system: … 3.2.7.2. L1e — L7e Intake manifold description and working principle (e.g. fixed length/variable length/swirl valves) (4) (include detailed drawings and/or photos): … * 3.2.7.2.1. L1e — L7e Description and drawings of inlet pipes and their accessories (plenum chamber, heating device with control strategy, additional air intakes, etc.): … 3.2.7.3. L1e — L7e Intake air pressure charger: yes/no (4) 3.2.7.3.1. L1e — L7e Brief description and schematic drawing of the intake air-pressure charger system: … 3.2.7.3.2. L1e — L7e Working and control principles: … 3.2.7.3.3. L1e — L7e Type(s) (turbo or supercharger, other) (4) : … 3.2.7.3.4. L1e — L7e Maximum intake air-charge pressure and flow-rate at maximum torque and power: … kPa and g/s or charge pressure and flow-rate map: … kPa and g/s 3.2.7.4. L1e — L7e Waste gate: yes/no (4) 3.2.7.5. L1e — L7e Intercooler: yes/no (4) 3.2.7.5.1. L1e — L7e Type: air-air/air-water/other (4) * 3.2.7.5.2. L1e — L7e Intake depression at rated engine speed and at 100 % load (compression ignition engines only): … kPa 3.2.7.6. L1e — L7e Air filter, (drawings, photographs): … 3.2.7.7. L1e — L7e Intake air-silencer description (drawings, photographs): … * 3.2.7.7.1. L1e — L7e Working principle: … 3.2.8. Air-mass metering and control 3.2.8.1. L1e — L7e Brief description and schematic drawing of air-mass metering and control system: … 3.2.8.2. L1e — L7e Mechanical throttle body: yes/no (4) 3.2.8.3. L1e — L7e Electronic throttle control (ETC): yes/no (4) 3.2.8.3.1. L1e — L7e Schematic drawing of electronic throttle control: … * 3.2.8.3.1.2. L1e — L7e Description of ETC hardware redundancies regarding sensors/actuators/electric power/ground/control electronics: … 3.2.9. Spark delivery system and control 3.2.9.1. L1e — L7e Brief description and schematic drawing of spark delivery and control system: … 3.2.9.1.1. L1e — L7e Working principle: … L1e — L7e Ignition advance curve or map (7) at wide open throttle: … 3.2.9.1.3. L1e — L7e Static ignition timing (7) : … degrees before TDC at maximum torque and power 3.2.9.2. L1e — L7e Ion sense capability: yes/no (4) 3.2.9.3. L1e — L7e Spark plugs: 3.2.9.3.1. L1e — L7e Gap setting: … mm 3.2.9.4. L1e — L7e Ignition coil(s): * 3.2.9.4.1. L1e — L7e Working principle: … * 3.2.9.4.2. L1e — L7e Dwell angle and timing at wide open throttle: … 3.2.10. Powertrain cooling system and control 3.2.10.1. L1e — L7e Brief description and schematic drawing of powertrain cooling and control system: … 3.2.10.2. L1e — L7e Cooling system: liquid: yes/no (4) 3.2.10.2.1. L1e — L7e Maximum temperature at outlet: … K 3.2.10.2.2. L1e — L7e Nominal setting of the engine temperature control mechanism: … 3.2.10.2.3. L1e — L7e Nature of liquid: … 3.2.10.2.4. L1e — L7e Circulating pump(s): yes/no (4) 3.2.10.2.4.1. L1e — L7e Characteristics: … 3.2.10.2.5. L1e — L7e Drive ratio(s): … 3.2.10.2.6. L1e — L7e Description of the fan and its drive mechanism: … 3.2.10.3. L1e — L7e Air cooling: yes/no (4) 3.2.10.3.1. L1e — L7e Reference point: … 3.2.10.3.2. L1e — L7e Maximum temperature at reference point: … K 3.2.10.3.3. L1e — L7e) Fan: yes/no (4) 3.2.10.3.3.1. L1e — L7e Characteristics: … 3.2.10.3.3.2. L1e — L7e Drive ratio(s): … 3.2.11. Powertrain lubrication system and control 3.2.11.1. L1e — L7e Brief description and schematic drawing of powertrain lubrication and control system: … 3.2.11.2. L1e — L7e Lubrication system configuration(s) (wet sump, dry sump, other, pump/injection into induction system/mixed with the fuel, etc.) (4) : … 3.2.11.3. L1e — L7e Location of oil reservoir (if any): … 3.2.11.4. L1e — L7e Feed system (pump/injection into induction system/mixed with the fuel, etc.) (4) : … 3.2.11.5. L1e — L7e Lubricating pump: yes/no (4) … 3.2.11.6. L1e — L7e Oil cooler: yes/no (4) 3.2.11.6.1. L1e — L7e Drawing … 3.2.11.7. L1e — L7e Lubricant(s) characteristics: … 3.2.11.8. L1e — L7e Lubricant mixed with the fuel: yes/no (4) : … 3.2.11.8.1. L1e — L7e Percentage range of lubricant mixed with the fuel: … 3.2.12. Exhaust system and control 3.2.12.1. L1e — L7e Brief description and schematic drawing of exhaust devices for noise and tailpipe emission control: … 3.2.12.2. L1e — L7e Description and drawing of the exhaust manifold: … 3.2.12.3. L1e — L7e Description and detailed drawing of the exhaust device: … 3.2.12.4. L1e — L7e Maximum permissible exhaust back-pressure at rated engine speed and at 100 % load: … kPa (29) 3.2.12.5. L1e — L7e Type, marking of exhaust noise-abatement device(s): … * 3.2.12.6. L1e — L7e Noise-reducing measures in the engine compartment and on the engine where relevant for external noise: … 3.2.12.7. L1e — L7e Location of the exhaust outlet: … 3.2.12.8. L1e — L7e Exhaust noise-abatement device containing fibrous materials: yes/no (4) : … 3.2.13. Other electrical systems and control than those intended for the electrical propulsion 3.2.13.1. L1e — L7e Rated voltage: … V, positive/negative ground (4) 3.2.13.2. L1e — L7e Generator: yes/no (4) : 3.2.13.2.1. L1e — L7e Nominal output: … VA 3.2.13.3. L1e — L7e Battery(ies): yes/no (4) 3.2.13.3.1. L1e — L7e Capacity and other characteristics (mass,…): … 3.2.13.4. L1e — L7e Electric heating systems for the passenger compartment: yes/no (4) 3.3. Pure electric and hybrid electric propulsion and control 3.3.1. L1e — L7e Electric vehicle configuration: pure electric/hybrid electric/manpower — electric (4) : 3.3.2. L1e — L7e Brief description and schematic drawing of pure and hybrid electric propulsions and its control system(s): … 3.3.3. Electric propulsion motor 3.3.3.1. L1e — L7e Number of electric motors for propulsion: … 3.3.3.2. L1e — L7e Type (winding, excitation): … 3.3.3.3. L1e — L7e Operating voltage: … V 3.3.4. Propulsion batteries 3.3.4.1. L1e — L7e Primary propulsion battery 3.3.4.1.1. L1e — L7e Number of cells: … 3.3.4.1.2. L1e — L7e Mass: … kg 3.3.4.1.3. L1e — L7e Capacity: … Ah (Amp-hours) / … V 3.3.4.1.4. L1e — L7e Voltage: … V 3.3.4.1.5. L1e — L7e Position in the vehicle: … 3.3.4.2. L1e — L7e Secondary propulsion battery 3.3.4.2.1. L1e — L7e Number of cells: … 3.3.4.2.2. L1e — L7e Mass: … kg 3.3.4.2.3. L1e — L7e Capacity: … Ah (Amp-hours) / … V 3.3.4.2.4. L1e — L7e Voltage: … V 3.3.4.2.5. L1e — L7e Position in the vehicle: … 3.3.5. Hybrid electric vehicle 3.3.5.1. L1e — L7e Engine or motor combination (number of electric motor(s) and/or combustion engine(s)/other) (4) : … 3.3.5.2. L1e — L7e Category of hybrid electric vehicle: off-vehicle charging/not off-vehicle charging: 3.3.5.3. L1e — L7e Operating mode switch: with/without (4) 3.3.5.4. L1e — L7e Selectable modes: yes/no (4) 3.3.5.5. L1e — L7e Pure fuel consuming: yes/no (4) 3.3.5.6. L1e — L7e Vehicle propelled with fuel cell: yes/no (4) 3.3.5.7. L1e — L7e Hybrid operation modes: yes/no (4) (if yes, short description): … 3.3.6. Energy storage device 3.3.6.1. L1e — L7e Description: (battery, capacitor, flywheel/generator) (4) 3.3.6.2. L1e — L7e Identification number: … * 3.3.6.3. L1e — L7e Kind of electrochemical couple: … 3.3.6.4. L1e — L7e Energy (for battery: voltage and capacity Ah in 2h, for capacitor: J,…, for flywheel/generator: J,…,): … 3.3.6.5. L1e — L7e Charger: on-board/external/without (4) 3.3.7. Electric motor (describe each type of electric motor separately) … 3.3.7.1. L1e — L7e Primary use: propulsion motor/generator (4) 3.3.7.2. L1e — L7e When used as propulsion motor: single-/multi-motors (number) (4) : … 3.3.7.3. L1e — L7e Working principle: … 3.3.7.4. L1e — L7e Direct current/alternating current/number of phases: … 3.3.7.5. L1e — L7e Separate excitation/series/compound (4) : 3.3.7.6. L1e — L7e Synchronous/asynchronous (4) : 3.3.8. Electric motor control unit 3.3.8.1. L1e — L7e Identification number: … 3.3.9. Power controller 3.3.9.1. L1e — L7e Identification number: … 3.4. Other engines, electric motors or combinations (specific information concerning the parts of these motors) 3.4.1. Cooling system (temperatures permitted by the manufacturer) 3.4.1.1. L1e — L7e Liquid cooling: … 3.4.1.1.1. L1e — L7e Maximum temperature at outlet: … K 3.4.1.2. L1e — L7e Air cooling: … 3.4.1.2.1. L1e — L7e Reference point: … 3.4.1.2.2. L1e — L7e Maximum temperature at reference point: … K 3.4.2. Lubrication system 3.4.2.1. L1e — L7e Description of lubrication system: … 3.4.2.2. L1e — L7e Location of oil reservoir (if any): … 3.4.2.3. L1e — L7e Feed system (pump/injection into induction system/mixed with the fuel, etc.) (4) : … 3.4.2.4. L1e — L7e Lubricant mixed with the fuel: … 3.4.2.4.1. L1e — L7e Percentage: … 3.4.2.5. L1e — L7e Oil cooler: yes/no (4) : … * 3.4.2.5.1. L1e — L7e Drawing(s): … 3.5. Drive-train and control (13) 3.5.1. L1e — L7e Brief description and schematic drawing of the vehicle drive-train and its control system (gear shift control, clutch control or any other element of drive-train): … 3.5.2. Clutch 3.5.2.1. L1e — L7e Brief description and schematic drawing of the clutch and its control system: … 3.5.3. Transmission 3.5.3.1. L1e — L7e Brief description and schematic drawing of gear shift system(s) and its control: … 3.5.3.2. L1e — L7e Drawing of the transmission: … 3.5.3.3. L1e — L7e Type (mechanical, hydraulic, electric, manual/manual automated/automatic/CVT/ other (indicate).) (4) : … 3.5.3.4. L1e — L7e A brief description of the electrical/electronic components (if any): … 3.5.3.5. L1e — L7e Location relative to the engine: … 3.5.3.6. L1e — L7e Method of control: … 3.5.4. L1e — L7e Gear ratios Overview gear ratios Gear Internal transmission ratios (ratios of engine to transmission output shaft revolutions) Final drive ratio(s) (ratio of transmission output shaft to driven wheel revolutions) Total gear ratios Ratio (engine speed/vehicle speed) for manual transmission only Maximum for CVT ( 1 ) 1 2 3 … Minimum for CVT ( 1 ) Reverse 3.5.4.1. L3e-AxE, L3e-AxT Final drive ratio: … 3.5.4.2. L3e-AxE, L3e-AxT Overall gear ratio in highest gear: … 3.6. Safe-cornering device 3.6.1. L1e — L7e equipped with twinned wheels, L2e, L5e, L6e, L7e Safe-cornering device (Annex VIII to Regulation (EU) No 168/2013: yes/no (4) ; differential/other (4) 3.6.2. L1e — L7e equipped with twinned wheels, L2e, L5e, L6e, L7e Differential lock: yes/no/optional (4) 3.6.3. L1e — L7e Brief description and schematic drawing of the safe-cornering device, the differential lock and their control systems: … 3.7. Suspension and control 3.7.1. L1e — L7e Brief description and schematic drawing of suspension and its control system: … 3.7.2. L1e — L7e Drawing of the suspension arrangements: … 3.7.3. L1e — L7e Level adjustment: yes/no/optional (4) 3.7.4. L1e — L7e Brief description of the electrical/electronic components: … 3.7.5. L1e — L7e Stabilisers: yes/no/optional (4) 3.7.6. L1e — L7e Shock absorbers: yes/no/optional (4) 3.8. Passenger-compartment heating system and air-conditioning 3.8.1. Passenger-compartment heating system 3.8.1.1. L2e, L5e-B, L6e-B, L7e An overall drawing of the heating system giving its location on the vehicle (and the arrangement of the sound damping devices (including the position of the heat exchange points)): … 3.8.1.2. L2e, L5e-B, L6e-B, L7e An overall drawing of the heat-exchanger used in systems utilising the heat from the exhaust gases, or of the parts where that exchange takes place (in the case of heating systems using the heat provided by the engine cooling air): … 3.8.1.3. L2e, L5e-B, L6e-B, L7e A sectional drawing of the heat-exchanger or parts where heat exchange takes place, together with a statement of the wall thickness, of the materials used and the characteristics of their surface: … 3.8.1.4. L2e, L5e-B, L6e-B, L7e Specifications regarding the method of manufacture and technical data relating to other major components of the heating system, such as the fan: … 3.8.2. Air-conditioning 3.8.2.1. L2e, L5e-B, L6e-B, L7e Brief description and schematic drawing of air-conditioning and its control system: … 3.8.2.2. L2e, L5e-B, L6e-B, L7e Gas used as refrigerant in the air-conditioning system: … 3.8.2.3. L2e, L5e-B, L6e-B, L7e The air-conditioning system is designed to contain fluorinated greenhouse gases with global warming potential higher than 150: yes/no (4) . If Yes, fill in the following sections: 3.8.2.3.1. L2e, L5e-B, L6e-B, L7e Drawing and brief description of the air-conditioning system, including the reference or part number and material of the leak components: … 3.8.2.3.2. L2e, L5e-B, L6e-B, L7e Leakage of the air-conditioning system 3.8.2.3.3. L2e, L5e-B, L6e-B, L7e Reference or part number and material of the components of the system and test information (e.g. test report number, Type-approval number, etc.): … 3.8.2.3.4. L2e, L5e-B, L6e-B, L7e Overall leakage/year of the entire system: … g/year 3.9. Cycles designed to pedal 3.9.1. L1e Ratio manpower/electric power: … 3.9.2. L1e Maximum assistance factor: … 3.9.3. L1e Maximum vehicle speed for which the electric motor gives assistance: … km/h 3.9.4. L1e Switch-off distance: … km 4. GENERAL INFORMATION ON ENVIRONMENTAL AND PROPULSION PERFORMANCE 4.0 General information on environmental and propulsion performance 4.0.1. L1e — L7e Environmental step (16) : Euro … (3/4/5) (4) 4.1. Tailpipe emission-control system 4.1.1. L1e — L7e Brief description and schematic drawing of the tailpipe emission-control system and its control: … 4.1.2. Catalytic converter 4.1.2.1. L1e — L7e Configuration, number of catalytic converters and elements (information to be provided for each separate unit): … 4.1.2.2. L1e — L7e Drawing with dimensions, shape and volume of the catalytic converter(s): … 4.1.2.3. L1e — L7e Catalytic reaction: … * 4.1.2.4. L1e — L7e Total charge of precious metals: … * 4.1.2.5. L1e — L7e Relative concentration: … * 4.1.2.6. L1e — L7e Substrate (structure and material): … * 4.1.2.7. L1e — L7e Cell density: … * 4.1.2.8. L1e — L7e Casing for the catalytic converter(s): … 4.1.2.9. L1e — L7e Location of the catalytic converter(s) (place and reference distance in the exhaust line): … 4.1.2.10. L1e — L7e Catalyst heat-shield: yes/no (4) 4.1.2.11. L1e — L7e Brief description and schematic drawing of the regeneration system/method of exhaust after-treatment systems and its control system: … * 4.1.2.11.1. L1e — L7e Normal operating temperature range: … K 4.1.2.11.2. L1e — L7e Consumable reagents: yes/no (4) 4.1.2.11.3. L1e — L7e Brief description and schematic drawing of the reagent flow (wet) system and its control system: … 4.1.2.11.4. L1e — L7e Type and concentration of reagent needed for catalytic action: … * 4.1.2.11.5. L1e — L7e Normal operational temperature range of reagent: … K 4.1.2.11.6. L1e — L7e Frequency of reagent refill: continuous/maintenance (4) 4.1.2.12. L1e — L7e Identifying part number: … 4.1.3. Oxygen sensor(s) 4.1.3.1. L1e — L7e Oxygen sensor component(s) drawing(s): … 4.1.3.2. L1e — L7e Drawing of exhaust device with oxygen sensor location(s) (dimensions relative to exhaust valves): … 4.1.3.3. L1e — L7e Control range(s): … 4.1.3.4. L1e — L7e Identifying part number(s): … 4.1.3.5. L1e — L7e Description of oxygen sensor heating system and heating strategy: … 4.1.3.6. L1e — L7e Oxygen sensor heat shield(s): yes/no (4) 4.1.4. Secondary air-injection (air-inject in exhaust) 4.1.4.1. L1e — L7e Brief description and schematic drawing of the secondary air-injection system and its control system: … 4.1.4.2. L1e — L7e Configuration (mechanical, pulse air, air pump etc.) (4) : … 4.1.4.3. L1e — L7e Working principle: … 4.1.5. External exhaust gas recirculation (EGR) 4.1.5.1. L1e — L7e Brief description and schematic drawing of the EGR system (exhaust flow) and its control system: … 4.1.5.2. L1e — L7e Characteristics: … 4.1.5.3. L1e — L7e Water-cooled EGR system: yes/no (4) 4.1.5.4. L1e — L7e Air-cooled EGR system: yes/no (4) 4.1.6. Particulate filter 4.1.6.1. L1e — L7e PT component drawing with dimensions, shape and capacity of the particulate filter: … 4.1.6.2. L1e — L7e Design of the particulate filter: … 4.1.6.3. L1e — L7e Brief description and schematic drawing of the particulate filter and its control system: … 4.1.6.4. L1e — L7e Location (reference distance in the exhaust line): … 4.1.6.5. L1e — L7e Method or system of regeneration, description and drawing: … 4.1.6.6. L1e — L7e Identifying part number: … 4.1.7. Lean NOx trap 4.1.7.1. L1e — L7e Operation principle of lean NOx trap: … 4.1.8. Additional tailpipe emission-control devices (if any not covered under another heading) 4.1.8.1. L1e — L7e Working principle: … 4.2. Crankcase emission control system 4.2.1. L1e — L7e Configuration of crank-case gas recycling system (breather system, positive crank-case ventilation system, other)(4) (description and drawings). 4.3. Evaporative emission control system 4.3.1. L1e — L7e Evaporative emissions control system: yes/no (4) 4.3.2. L1e — L7e Drawing of the evaporative control system 4.3.3. L1e — L7e Drawing of the canister (including dimensions and indicating vent and purge mechanism) 4.3.4. L1e — L7e Working capacity: … g 4.3.5. L1e — L7e Adsorption material: … (e.g. charcoal, carbon, synthetic, …) 4.3.6. L1e — L7e Housing material: … (e.g. plastic, steel, …) 4.3.7. L1e — L7e Schematic drawing of the fuel tank, indicating capacity and material: … 4.3.8. L1e — L7e Drawing of the heat-shield between tank and exhaust device: … 4.4. Additional information on environmental and propulsion unit performance 4.4.1. L1e — L7e Description and/or schematic drawings of additional pollution-control devices: … 4.4.2. L1e — L7e Location of the coefficient of absorption symbol (compression-ignition engines only): … 4.4.3. L1e — L7e Applicable information document set out in respectively UN Regulation No 9, 41 or 63 shall supplement this information document with regard to the sound level. 4.4.4. L1e — L7e Applicable information document set out in respectively UN Regulation No 92 shall supplement this information document with regards to the noise-abatement devices installed on the vehicle. 5. VEHICLE PROPULSION FAMILY 5.1. L1e — L7e To define the vehicle propulsion family, the manufacturer shall submit the information required for classification criteria set out in point 3 of Annex XI to Commission Delegated Regulation (EU) No 134/2014, if not already provided in the information document. 6. INFORMATION ON FUNCTIONAL SAFETY 6.1. Audible warning devices 6.1.1. L1e — L7e Summary description of device(s) used and their purpose: … 6.1.2. L1e — L7e Drawing(s) showing the location of the audible warning device(s) in relation to the structure of the vehicle: … 6.1.3. L1e — L7e Details of the method of attachment, including the part of the vehicle structure to which the audible warning device(s) is (are) attached: … 6.1.4. L1e — L7e Electrical/pneumatic circuit diagram: … 6.1.4.1. L1e — L7e Voltage: AC/DC (4) 6.1.4.2. L1e — L7e Rated voltage or pressure: … 6.1.5. L1e — L7e Drawing of the mounting device: … 6.2. Braking, including anti-lock and combined braking systems 6.2.1. L1e — L7e Characteristics of the brakes, including details and drawings of the drums, discs, hoses, make and type of shoe/pad assemblies and/or linings, effective braking areas, radius of drums, shoes or discs, mass of drums, adjustment devices, relevant parts of the axle(s) and suspension, levers, pedals (4) : … 6.2.2. L1e — L7e Operating diagram, description and/or drawing of the braking system, including details and drawings of the transmission and controls as well as a brief description of the electrical and/or electronic components used in the braking system (4) : 6.2.2.1. L1e — L7e Front, rear and sidecar brakes, disc and/or drum (4) : 6.2.2.2. L1e — L7e Parking braking system: … 6.2.2.3. L1e — L7e Any additional braking system: … 6.2.3. L1e — L7e Vehicle is equipped to tow a trailer with no brake/overrun brake/electric/pneumatic/hydraulic service brakes: yes/no (4) : … 6.2.4. L1e — L7e Anti-lock/Combined braking system 6.2.4.1. L1e — L7e Anti-lock braking system: yes/no/optional (4) 6.2.4.2. L1e — L7e Combined braking system: yes/no/optional (4) 6.2.4.3. L1e — L7e Anti-lock and combined braking system: yes/no/optional (4) 6.2.4.4. L1e — L7e Schematic drawing(s): … 6.2.5. L1e — L7e Hydraulic reservoir(s) (volume and location): … 6.2.6. L1e — L7e Particular characteristics of the braking system(s) 6.2.6.1. L1e — L7e Brake shoes and/or pads (4) : … 6.2.6.2. L1e — L7e Linings and/or pads (indicate make, type, grade of material or identification mark): … 6.2.6.3. L1e — L7e Brake levers and/or pedals (4) : … 6.2.6.4. L1e — L7e Other devices (where applicable): drawing and description: … 6.3. Electrical safety 6.3.1. L1e — L7e Brief description of the power circuit components installation and drawings/photographs showing the location of the power circuit components installation: … 6.3.2. L1e — L7e Schematic diagram of all electrical functions included in power circuit: … 6.3.3. L1e — L7e Working voltage(s) (V): … 6.3.4. L1e — L7e Description of protection against electric-shocks: … 6.3.5. L1e — L7e Fuse and/or circuit breaker yes/no/optional (4) 6.3.5.1. L1e — L7e Diagram showing the functional range: … 6.3.6. L1e — L7e Configuration of power wiring harness: … 6.4. Front and rear protective structures 6.4.1. Front protective structure 6.4.1.1. L1e — L7e Detailed technical description (including photographs or drawings): … 6.4.1.2. L1e — L7e Materials used: … 6.4.2. Rear protective structure 6.4.2.1. L1e — L7e Detailed technical description (including photographs or drawings): … 6.4.2.2. L1e — L7e Materials used: … 6.5. Glazing, windscreen wipers and washers, and defrosting and demisting systems 6.5.1. Windscreen 6.5.1.1. L2e, L5e, L6e, L7e Materials used: … 6.5.1.2. L2e, L5e, L6e, L7e Method of mounting: … 6.5.1.3. L2e, L5e, L6e, L7e Angle of inclination: … 6.5.1.4. L2e, L5e, L6e, L7e Windscreen accessories and the position in which they are fitted, together with a brief description of any electrical/electronic components: … 6.5.1.5. L2e, L5e, L6e, L7e Drawing of the windscreen with dimensions: … 6.5.2. Other windows 6.5.2.1. L2e, L5e, L6e, L7e Materials used: … 6.5.2.2 L2e, L5e, L6e, L7e A brief description of the electrical/electronic components (if any) of the window lifting mechanism: … 6.5.3. Opening roof glazing 6.5.3.1. L2e, L5e, L6e, L7e Materials used: … 6.5.4. Other glass panes 6.5.4.1. L2e, L5e, L6e, L7e Materials used: … 6.6. Windscreen wiper(s) 6.6.1. L2e, L5e, L6e, L7e Detailed technical description (including photographs or drawings): … 6.7. Windscreen washer 6.7.1. L2e, L5e, L6e, L7e Detailed technical description (including photographs or drawings): … 6.7.2. L2e, L5e, L6e, L7e Capacity of the reservoir: … l 6.8. Defrosting and demisting 6.8.1. L2e, L5e, L6e, L7e Detailed technical description (including photographs or drawings): … 6.9. Driver-operated controls including identification of controls, tell-tales and indicators 6.9.1. L1e — L7e Arrangement and identification of controls, tell-tales and indicators: … 6.9.2. L1e — L7e Photographs and/or drawings of the arrangement of symbols and controls, tell-tales and indicators: … 6.9.3. L1e — L7e Controls, tell-tales and indicators for which, when fitted, identification is mandatory, including the identification symbols to be used for that purpose: 6.9.4. L1e — L7e Summary table: the vehicle is equipped with the following driver-operated controls, including indicators and tell-tales (4) Controls, tell-tales and indicators for which, when fitted, identification is mandatory, and symbols to be used for that purpose Symbol No Device Control / indicator available ( 2 ) Identified by symbol ( 2 ) Where ( 3 ) Tell-tale available ( 2 ) Identified by symbol ( 2 ) Where ( 3 ) 1 Master light 2 Dipped-beam head lamps 3 Main-beam head lamps 4 Position (side) lamps 5 Front fog lamps 6 Rear fog lamp 7 Headlamp levelling device 8 Parking lamps 9 Direction indicators 10 Hazard warning 11 Windscreen wiper 12 Windscreen washer 13 Windscreen wiper and washer 14 Headlamp cleaning device 15 Windscreen demisting and defrosting 16 Rear window demisting and defrosting 17 Ventilating fan 18 Diesel pre-heat 19 Choke 20 Brake failure 21 Fuel level 22 Battery charging condition 23 Engine coolant temperature 24 Malfunction indicator light (MI) 6.9.5. L1e — L7e Controls, tell-tales and indicators for which, when fitted, identification is optional, and symbols which shall be used if they are to be identified Symbol No Device Control / indicator available ( 4 ) Identified by symbol ( 4 ) Where ( 5 ) Tell-tale available ( 4 ) Identified by symbol ( 4 ) Where ( 5 ) 1 Parking brake 2 Rear window wiper 3 Rear window washer 4 Rear window wiper and washer 5 Intermittent windscreen wiper 6 Audible warning device (horn) 7 Front hood (bonnet) 8 Rear hood (boot) 9 Seat belt 10 Engine oil pressure 11 Unleaded petrol 12 … 13 … 6.10. Speedometer and odometer 6.10.1. Speedometer 6.10.1.1. L1e — L7e Photographs and/or drawings of the complete system: … 6.10.1.2. L1e — L7e Vehicle speed range displayed: … 6.10.1.3. L1e — L7e Tolerance of the measuring mechanism of the speedometer: … 6.10.1.4. L1e — L7e Technical constant of the speedometer: … 6.10.1.5. L1e — L7e Method of operation and description of the drive mechanism: … 6.10.1.6. L1e — L7e Overall transmission ratio of the drive mechanism: … 6.10.2. Odometer 6.10.2.1. L1e — L7e Tolerance of the measuring mechanism of the odometer: … 6.10.2.2. L1e — L7e Method of operation and description of the drive mechanism: … 6.11. Installation of lighting, light-signalling devices, including automatic switching of lighting 6.11.1. L1e — L7e List of all devices (mentioning the number, make(s),type, component type-approval mark(s), the maximum intensity of the main-beam headlamps, colour, the corresponding tell-tale): … 6.11.2. L1e — L7e Diagram showing the location of the lighting and light-signalling devices: … 6.11.3. L1e — L7e Hazard warning lamps: … 6.11.4. L1e — L7e Brief description of the electrical and/or electronic components used in the lighting system and in the light-signalling system: … 6.11.5. L1e — L7e For every lamp and reflector, supply the following information (in writing and/or by diagram): 6.11.5.1. L1e — L7e Drawing showing the extent of the illuminating surface: … 6.11.5.2. L1e — L7e Method used to define the apparent surface in accordance with point 2.10 of UNECE Regulation No 48 ( OJ L 323, 6.12.2011, p. 46 ): … 6.11.5.3. L1e — L7e Axis of reference and centre of reference: … 6.11.5.4. L1e — L7e Method of operation of concealable lamps: … 6.11.6. L1e — L7e Description/drawing and type of headlamp levelling device (e.g. automatic, stepwise manually adjustable, continuously manually adjustable) (4) : … 6.11.6.1. L1e — L7e Control device: … 6.11.6.2. L1e — L7e Reference marks: … 6.11.6.3. L1e — L7e Marks assigned for loading conditions: … 6.12. Rearward visibility 6.12.1. Rear-view mirrors (stating for each mirror) 6.12.1.1. L1e — L7e Drawing(s) for the identification of the mirror showing the position of the mirror relative to the vehicle structure: … 6.12.1.2. L1e — L7e Details of the method of attachment including that part of the vehicle structure to which it is attached: … 6.12.1.3. L1e — L7e A brief description of the electronic components of the adjustment system: … 6.12.2. L1e — L7e Devices for indirect vision other than mirrors 6.12.2.1. L1e — L7e Description of the device: … 6.12.2.2. L1e — L7e In the case of a camera-monitor device, the detection distance (mm), contrast, luminance range, glare correction, display performance (black and white/colour (4) ), image repetition frequency, luminance reach of the monitor (4) : … 6.12.2.3. L1e — L7e Sufficiently detailed drawings to identify the complete device, including installation instructions; the position for the EU type-approval mark has to be indicated on the drawings: … 6.13. Rollover protective structure (ROPS) 6.13.1. L7e-B2 Detailed technical description, position, fixing, etc. (including photographs or drawings): … 6.13.2. ROPS by Frame (4) 6.13.2.1. L7e-B2 Internal and external dimensions: … 6.13.2.2. L7e-B2 Material(s) and method of construction: … 6.13.3. ROPS by Cab (4) 6.13.3.1. L7e-B2 Other weather protection arrangements (description): … 6.13.3.2. L7e-B2 Internal and external dimensions: … 6.13.4. ROPS by Roll bar(s) mounted at front/rear (4) , fold-down/not fold down (4) 6.13.4.1. L7e-B2 Dimensions: … 6.13.4.2. L7e-B2 Material(s) and method of construction: … 6.14. Safety belts and/or other restraints 6.14.1. L2e, L4e, L5e-B, L6e-B, L7e Number and position of safety belts and restraint systems and seats on which they can be used, please fill out table below: (L = left side, R = right side, C = centre) Safety belt configuration and associated information Complete EU type-approval mark Variant, if applicable Belt adjustment device for height (indicate yes/no/optional) First row of seats L C R Second row of seats L C R L = left, C= centre, R=right 6.14.2. L2e, L4e, L5e-B, L6e-B, L7e Description of a specific type of belt, with one anchorage attached to the seat back-rest or incorporating an energy-dissipation device: … 6.14.3. L2e, L4e, L5e-B, L6e-B, L7e Number and location of the anchorages: … 6.14.4. L2e, L4e, L5e-B, L6e-B, L7e Brief description of electrical/electronic components: … 6.15. Safety belt anchorages 6.15.1. L2e, L4e, L5e-B, L6e-B, L7e Photographs and/or drawings of the bodywork showing the true, effective location and dimensions of the anchorages, together with an indication of the R-point: … 6.15.2. L2e, L4e, L5e-B, L6e-B, L7e Drawings of the anchorages and the parts of the vehicle structure to which they are attached (together with a statement on the nature of the materials used): … 6.15.3. L2e, L4e, L5e-B, L6e-B, L7e Designation of the types of belts (14) authorised for attachment to the anchorages on the vehicle: … Safety-belt anchorage configuration and associated information Anchorage location Vehicle structure Seat structure First row of seats Right-hand seat Lower anchorages Upper anchorages outboard inboard Centre seat Lower anchorages Upper anchorages right left Left-hand seat Lower anchorages Upper anchorages outboard inboard Second row of seats Right-hand seat Lower anchorages Upper anchorages outboard inboard Centre seat Lower anchorages Upper anchorages right left Left-hand seat Lower anchorages Upper anchorages outboard inboard 6.15.4. L2e, L4e, L5e-B, L6e-B, L7e Type-approval mark for each position: … 6.15.5. L2e, L4e, L5e-B, L6e-B, L7e Special devices (example: seat-height adjustment, preloading device, etc.): … 6.15.6. L2e, L4e, L5e-B, L6e-B, L7e Photographs and/or drawings of the bodywork showing the true, effective location and dimensions of the anchorages, together with an indication of the R-point: … 6.15.7. L2e, L4e, L5e-B, L6e-B, L7e Observation: … 6.16. Seating positions (saddles and seats) 6.16.1. L1e — L7e Number of seating positions: … 6.16.1.1. L2e, L5e, L6e, L7e Location and arrangement (8) : … 6.16.2. L1e — L7e Seating position configuration: seat/saddle (4) 6.16.3. L1e — L7e Description and drawings of: 6.16.3.1. L1e — L7e The seats and their anchorages: … 6.16.3.2. L1e — L7e The adjustment system: … 6.16.3.3. L1e — L7e The displacement and locking systems: … 6.16.3.4. L1e — L7e The seat-belt anchorages incorporated in the seat structure: … 6.16.3.5. L1e — L7e The parts of the vehicle used as anchorages: … 6.16.4. L2e, L4e, L5e-B, L6e-B, L7e Coordinates or drawing of the R-point(s) of all seating positions: … 6.16.4.1. L2e, L4e, L5e-B, L6e-B, L7e Driver’s seat: … 6.16.4.2. L2e, L4e, L5e-B, L6e-B, L7e All other seating positions: … 6.16.5. L1e — L7e Design torso angle: … 6.16.5.1. L1e — L7e Driver’s seat: … 6.16.5.2. L1e — L7e All other seating positions: … 6.16.6. L1e — L7e Range of seat adjustment: … 6.16.6.1. L1e — L7e Driver’s seat: … 6.16.6.2. L1e — L7e All other seating positions: … 6.17. Steer-ability, cornering properties and turn-ability 6.17.1. L1e — L7e Schematic diagram of steered axle(s) showing steering geometry: … 6.17.2. Transmission and control of steering 6.17.2.1. L1e — L7e Configuration of steering transmission (specify for front and rear): … 6.17.2.2. L1e — L7e Linkage to wheels (including other than mechanical means; specify for front and rear): … 6.17.2.2.1. L1e — L7e A brief description of the electrical/electronic components: … 6.17.2.3. L1e — L7e Diagram of the steering transmission: … 6.17.2.4. L2e, L5e, L6e, L7e Schematic diagram(s) of the steering control(s): … 6.17.2.5. L2e, L5e, L6e, L7e Range and method of adjustment of the steering control(s): … 6.17.2.6. L2e, L5e, L6e, L7e Method of assistance: … 6.17.3. Maximum steering angle of the wheels 6.17.3.1. L1e — L7e To the right: … degrees; number of turns of the steering wheel (or equivalent data): … 6.17.3.2. L1e — L7e To the left: … degrees; number of turns of the steering wheel (or equivalent data): … 6.18. Tyres/wheels combination 6.18.1. Tyres : 6.18.1.1. Size designation 6.18.1.1.1. L1e — L7e Axle 1: … 6.18.1.1.2. L1e — L7e Axle 2: … 6.18.1.1.3. L4e Sidecar wheel: … 6.18.1.2. L1e — L7e Minimum load-capacity index: … with the maximum load on each tyre: … Kg 6.18.1.3. L1e — L7e Minimum-speed category symbol compatible with the theoretical maximum design vehicle speed: … 6.18.1.4. L1e — L7e Tyre pressure(s) as recommended by the vehicle manufacturer: … kPa 6.18.2. Wheels : 6.18.2.1. L1e — L7e Rim size(s): … 6.18.2.2. L1e — L7e Categories of use compatible with the vehicle: … 6.18.2.3. L1e — L7e Nominal rolling circumference: … 6.19. Vehicle maximum speed limitation plate and its location on the vehicle 6.19.1. L7e-B1 and L7e-B2 Maximum speed limitation plate (indicate the reflecting material used; drawings and photos may be used as appropriate): … 6.19.2. L7e-B1 and L7e-B2 Location of maximum speed limitation plate (indicate variants where necessary; drawings and photos may be used as appropriate): … 6.19.3. L7e-B1 and L7e-B2 Height above road surface, upper edge: … mm 6.19.4. L7e-B1 and L7e-B2 Height above road surface, lower edge: … mm 6.19.5. L7e-B1 and L7e-B2 Distance of the centre line from the longitudinal median plane of the vehicle: … mm 6.19.6. L7e-B1 and L7e-B2 Distance from the left vehicle edge: … mm 6.20. Vehicle occupant protection, including interior fittings and vehicle doors 6.20.1. Bodywork 6.20.1.1. L2e, L5e-B, L6e-B, L7e Materials used and methods of construction: … 6.20.2. Occupant doors, latches and hinges 6.20.2.1. L2e, L5e, L6e, L7e Number of doors, and its configuration, dimensions and maximum angle of opening (5) : … 6.20.2.2. L2e, L5e, L6e, L7e Drawing of latches and hinges and of their position in the doors: … 6.20.2.3. L2e, L5e, L6e, L7e Technical description of latches and hinges: … 6.20.2.4. L2e, L5e, L6e, L7e Details, including dimensions, of entrances, steps and necessary handles where applicable: … 6.20.3. Interior protection for occupants 6.20.3.1. L2e, L5e, L6e, L7e Photographs, drawings and/or an exploded view of the interior fittings, showing the parts in the passenger compartment and the materials used (with the exception of interior rear view mirrors, arrangement of controls, seats and the rear part of seats), roof and opening roof, backrest: … 6.20.4. Head restraints 6.20.4.1. L2e, L5e, L6e, L7e Head restraints: integrated/detachable/separate (4) 6.20.4.2. L2e, L5e, L6e, L7e Detailed description of the head restraint, specifying in particular the nature of the padding material or materials and, where applicable, the position and specifications of the braces and anchorage pieces for the type of seat for which approval is sought: … 6.20.4.3. L2e, L5e, L6e, L7e In the case of a ‘separate’ head restraint 6.20.4.3.1. L2e, L5e, L6e, L7e Detailed description of the structural zone to which the head restraint is intended to be fixed: … 6.20.4.3.2. L2e, L5e, L6e, L7e Scale drawings of the significant parts of the structure and the head restraint: … 6.21. Maximum continuous total power and/or maximum vehicle speed limitation by design 6.21.1. Propulsion and/or drive-train output governors 6.21.1.1. L1e — L7e Number (minimum two, exemption L3e-A3 and L4e-A3): 6.21.1.2. L1e — L7e How is the redundancy of governors ensured?: … 6.21.1.3. L1e — L7e Nominal cut-off point no 1: … 6.21.1.3.1. L1e — L7e Engine/motor/drive-train rotation speed at which cut-off starts under load: … min -1 6.21.1.3.2. L1e — L7e Maximum rotation speed at the minimum engine load: … min -1 6.21.1.4. L1e — L7e Nominal cut-off point no 2: … 6.21.1.4.1 L1e — L7e Engine/motor/drive-train rotation speed at which cut-off starts under load (4) : … min -1 6.21.1.4.2. L1e — L7e Maximum rotation speed at the minimum engine load: … min -1 6.21.1.5. L1e — L7e The stated purpose of governor(s): maximum design vehicle speed limitation/maximum power limitation/engine over-speed protection (4) : … 7. INFORMATION ON VEHICLE CONSTRUCTION 7.1. Coupling devices and attachments 7.1.1. L1e — L7e L-category vehicle equipped with coupling device: yes/no/optional (4) 7.1.2. L1e — L7e Guidelines and information for consumers in all EU languages regarding the impact on the driveability of using a trailer with an L-category vehicle included in the owner's manual: yes/no (4) 7.1.3. L1e — L7e For coupling-device approved as separate technical unit: installation and operating instructions added to documentation: yes/no (4) 7.1.4. L1e — L7e Photographs and/or drawings showing the position and the construction of the coupling-devices: … 7.1.5. L1e — L7e Instructions for attaching the coupling-type to the vehicle and photographs or drawings of the fixing points on the vehicle as stated by the manufacturer; additional information, if the use of the coupling-type is restricted to certain variants or versions of the vehicle type: … 7.1.6. L1e — L7e Attachment points for a secondary coupling and/or breakaway cable (drawings and pictures may be used as appropriate): yes/no (4) 7.2. Devices to prevent unauthorised use 7.2.1. Protective device 7.2.1.1. L1e — L7e Summary description of protective device(s) used: … 7.2.2. Vehicle immobiliser 7.2.2.1. L1e — L7e Technical description of the vehicle immobiliser and of the measures taken against inadvertent activation: … 7.2.3. Alarm system 7.2.3.1. L1e — L7e Description of the alarm system and of the vehicle parts involved in its installation: … 7.2.3.2. L1e — L7e List of the main components comprising the alarm system: … 7.3. Electromagnetic compatibility (EMC) 7.3.1. L1e — L7e Requirements under UNECE Regulation No 10 ( OJ L 254, 20.9.2012, p. 1 ) are met with relevant documentation included in the information document: yes/no (4) 7.3.2. L1e — L7e Table or drawing of radio-interference control equipment: … 7.3.3. L1e — L7e Particulars of the nominal value of the direct-current resistance, and, in the case of resistive ignition cables, of their nominal resistance per metre: … 7.4. External projections 7.4.1. L1e — L7evehicles with bodywork General arrangement (drawing or photographs accompanied if necessary by dimensional details and/or text) indicating the position of the attached sections and views, of any parts of the exterior surface which can be regarded as critical for external projections, for example, and where relevant: bumpers, floor line, door and window pillars, air-intake grilles, radiator grille, windscreen wipers, rain gutter channels, handles, slide rails, flaps, door hinges and locks, hooks, eyes, winches, decorative trim, badges, emblems and recesses and any other parts of the exterior surface which can be regarded as critical (e.g. lighting equipment): … 7.5. Fuel storage 7.5.1. Fuel tank(s) 7.5.1.1. Main fuel tank(s) 7.5.1.1.1. L1e — L7e Maximum capacity: … 7.5.1.1.2. L1e — L7e Materials used: … 7.5.1.1.3. L1e — L7e Fuel tank inlet: restricted orifice/label (4) … 7.5.1.2. Reserve fuel tank(s) 7.5.1.2.1. L1e — L7e Maximum capacity: … 7.5.1.2.2. L1e — L7e Materials used: … 7.5.1.2.3. L1e — L7e Fuel tank inlet: restricted orifice/label (4) … 7.5.1.3. L1e — L7e Drawing and technical description of the tank(s) with connections and lines of the breathing and venting system, locks, valves, fastening devices: … 7.5.1.4. L1e — L7e Drawing clearly showing the position of the tank(s) in the vehicle: … 7.5.1.5. L1e — L7e Drawing of the heat shield between tank and exhaust device: … 7.5.2. Compressed natural gas (CNG) container(s) 7.5.2.1. L1e — L7e Applicable information document set out in UNECE regulation No 110 ( 6 ) as prescribed for vehicle category M1 shall supplement this information document with regards to the CNG tanks installed on the vehicle. 7.5.3. L1e — L7e Liquefied petroleum gas (LPG)container(s) 7.5.3.1. L1e — L7e Applicable information document set out in UNECE regulation No 67 ( 7 ) as prescribed for vehicle category M1 shall supplement this information document with regards to the LPG tanks installed on the vehicle. 7.6. On-board diagnostics (OBD) functional requirements 7.6.1 On-board diagnostics system 7.6.1.1. L1e — L7e Stage I: yes/no (4) and/or 7.6.1.2. L1e — L7e Stage II: yes/no (4) 7.6.2. OBD system general information 7.6.2.1. L3e—L7e (10) Written description and/or drawing of the malfunction indicator (MI): … 7.6.2.2. L3e—L7e (10) List and purpose of all components monitored by the OBD system: … 7.6.2.3. L3e— L7e (10) Written description (general working principles) for all OBD stage I circuit (open circuit, shorted low and high, rationality) and electronics (PCU/ECU internal and communication) diagnostics: … 7.6.2.4. L3e—L7e (10) Written description (general working principles) for all OBD stage I diagnostic functionality triggering any operating mode which significantly reduces engine torque in case of fault detection: … 7.6.2.5. L3e— L7e (10) Written description of the communication protocol(s) supported: … 7.6.2.6. L3e—L7e (10) Physical location of diagnostic-connector (add drawings and photographs): … 7.6.2.7. L3e— L7e (10) Written description in case of voluntary compliance with OBD stage II (general working principles): 7.6.2.7.1. L3e — L7e (10) Positive-ignition engines 7.6.2.7.1.1. L3e — L7e (10) Catalyst monitoring: … 7.6.2.7.1.2. L3e — L7e (10) Misfire detection: … 7.6.2.7.1.3. L3e — L7e (10) Oxygen sensor monitoring: … 7.6.2.7.1.4. L3e — L7e (10) Other components monitored by the OBD system: … 7.6.2.7.2. L3e — L7e (10) Compression-ignition engines 7.6.2.7.2.1. L3e — L7e (10) Catalyst monitoring: … 7.6.2.7.2.2. L3e — L7e (10) Particulate filter monitoring: … 7.6.2.7.2.3. L3e — L7e (10) Electronic fuelling system monitoring: … 7.6.2.7.2.4. L3e — L7e (10) deNOx system monitoring: … 7.6.2.7.2.5. L3e — L7e (10) Other components monitored by the OBD system: … 7.6.2.7.3 L3e — L7e (10) Criteria for MI activation (fixed number of driving cycles or statistical method): … 7.6.2.7.4. L3e — L7e (10) List of all OBD output codes and formats used (with explanation of each): … 7.6.3. OBD compatibility The following additional information shall be provided by the vehicle manufacturer to enable the manufacture of OBD-compatible replacement or service parts, diagnostic tools and test equipment : 7.6.3.1. L3e — L7e (10) A comprehensive document describing all sensed components concerned with the strategy for fault detection and MI activation (fixed number of driving cycles or statistical method). This shall, include a list of relevant secondary sensed parameters for each component monitored by the OBD system. The document shall also list all OBD output codes and formats (with an explanation of each) used in association with individual emission-related powertrain components and individual non-emission-related components, where monitoring the component is used to determine MI activation. This shall contain, in particular, a comprehensive explanation for the data given in service $05 Test ID $ 21 to FF and the data given in service $06: … 7.6.3.2. L3e — L7e (10) For vehicle types using a communication link in accordance with ISO 15765-4 ‘Road vehicles, diagnostics on controller area network (CAN) — Part 4: requirements for emissions-related systems’, the manufacturer shall provide a comprehensive explanation for the data given in service $06 Test ID $00 to FF, for each OBD monitor ID supported: … 7.6.3.3. L3e — L7e (10) The information required above may be provided in table form as described below. Example OBD fault-code overview list Component Fault code Monitoring strategy Fault detection criteria MI activation criteria Secondary parameters Preconditioning Demonstration test Intake air temperature sensor open circuit P0xxxxzz Comparison with temperature model after cold start > 20 degr difference between measured and modelled intake air temperature 3 rd cycle Coolant and intake air temperature sensor signals Two type I cycles Type I 7.6.3.4. L3e — L7e (10) Description of ETC diagnostic fault codes: … 7.6.4. Communication protocol information The following information shall be referenced to a specific vehicle make, model and variant, or identified using other workable definitions such as VIN or vehicle and systems identification : 7.6.4.1. L3e — L7e (10) Any protocol information system needed to enable complete diagnostics in addition to the standards prescribed in point 3.8. of Appendix 1 to Annex XII to Commission Delegated Regulation (EU) No 44/2014, such as additional hardware or software protocol information, parameter identification, transfer functions, ‘keep alive’ requirements, or error conditions; 7.6.4.2. L3e — L7e (10) Details of how to obtain and interpret all fault codes not in accordance with the standards prescribed in point 3.11. of Appendix 1 to Annex XII to Commission Delegated Regulation (EU) No 44/2014 7.6.4.3. L3e — L7e (10) A list of all available live data parameters including scaling and access information; 7.6.4.4. L3e — L7e (10) A list of all available functional tests including device activation or control and the means to implement them; 7.6.4.5. L3e — L7e (10) Details of how to obtain all component and status information, time stamps, pending DTC and freeze frames; 7.6.4.6. L3e — L7e (10) PCU/ECU identification and variant coding; 7.6.4.7. L3e — L7e (10) Details of how to reset service lights; 7.6.4.8. L3e — L7e (10) Location of diagnostic connector and connector details; 7.6.4.9. L3e — L7e (10) Engine code identification. 7.6.5. Test and diagnosis of OBD monitored components 7.6.5.1. L3e — L7e (10) A description of tests to confirm its functionality, at the component or in the harness: 7.7. Passenger handholds and footrests 7.7.1. Handholds 7.7.1.1. L1e — L7e Configuration: strap and/or handle (4) 7.7.1.3. L1e — L7e Photographs and/or drawings showing the location and the construction: 7.7.2. Footrests 7.7.2.1. L1e — L7e Photographs and/or drawings showing the location and the construction: 7.8. Registration plate space 7.8.1. L1e — L7e Location of rear registration plate (indicate variants where necessary; drawings may be used as appropriate): … 7.8.1.1. L1e — L7e Height above road surface, upper edge: … mm 7.8.1.2. L1e — L7e Height above road surface, lower edge: … mm 7.8.1.3. L1e — L7e Distance of the centre line from the longitudinal median plane of the vehicle: … mm 7.8.1.4. L1e — L7e Dimensions (length x width): … mm x … mm 7.8.1.5. L1e — L7e Inclination of the plane to the vertical: … degr. 7.8.1.6. L1e — L7e Angle of visibility in the horizontal plane: … degr 7.9. Stands 7.9.1. L1e, L3e Configuration: central and/or side (4) : … 7.9.2. L1e, L3e Construction material used: … 7.9.3. L1e, L3e Photographs and drawings showing the location of the stand(s) in relation to the structure of the vehicle: … 7.9.4. L1e, L3e Description of the method to prevent contact of the stand with the ground when the vehicle is being propelled: … ( 1 ) OJ L 7, 10.1.2014, p. 1 . ( 2 ) OJ L 25, 28.1.2014, p. 1 . ( *1 ) Commission Delegated Regulation (EU) No 134/2014 of 16 December 2013 supplementing Regulation (EU) No 168/2013 of the European Parliament and of the Council with regard to environmental and propulsion unit performance requirements and amending Annex V thereof ( OJ L 53, 21.2.2014, p. 1 ). ( *2 ) Contracting parties to the Revised 1958 Agreement. ( *3 ) To be indicated if not obtainable from the type-approval number. ( *4 ) The approval authority shall complete the references for the test reports, established by regulatory acts, for which no type-approval certificate is available. ( 3 ) OJ L 72, 14.3.2008, p. 1 . ( 4 ) OJ L 120, 7.5.2011, p. 1 . ( 5 ) Regulation (EC) No 79/2009 of the European Parliament and of the Council of 14 January 2009 on type-approval of hydrogen-powered motor vehicles, and amending Directive 2007/46/EC ( OJ L 35, 4.2.2009, p. 32 ). ( 6 ) OJ L 120, 7.5.2011, p. 1 . ( 7 ) OJ L 72, 14.3.2008, p. 1 . ( 1 ) ( + ) Continuously variable transmission. ( 2 ) ( + ) x = yes - = no or not separately available o = optional. ( 3 ) ( ++ ) d = directly on control, indicator or tell-tale c = in close vicinity. ( 4 ) ( + ) x = yes - = no or not separately available o = optional. ( 5 ) ( ++ ) d = directly on control, indicator or tell-tale c = in close vicinity.