The Smoke Control Areas (Exempted Fireplaces) (Wales) Order 2011

Section 1Title, commencement and application

(1) The title of this Order is the Smoke Control Areas (Exempted Fireplaces) (Wales) Order 2011 and it comes into force on 4 February 2011.

(2) This Order applies in relation to Wales.

Section 2Classes of fireplaces exempted from section 20 of the Clean Air Act 1993

The classes of fireplaces described in the Schedule are, subject to the conditions listed, exempted from the provisions of section 20 of the Clean Air Act 1993 (which prohibits smoke emissions in smoke control areas).

Section 3Revocation

The Smoke Control Areas (Exempted Fireplaces) (Wales) Order 2009 ( S.I. 2009/3224) (W.278) is revoked.

Section 1

The fireplace must be installed, maintained and operated in accordance with the installation and use instruction manual reference: “Part No 106870 Issue No. 1” dated February 2010 and supplementary instruction manual reference: “Part No 106872 Issue No. 1” dated May 2010.

The appliance will be fitted with a mechanical stop to prevent closure of the air control beyond the 40% open position when sold into smoke control areas.

Section 1

The fireplace must be installed, maintained and operated in accordance with the instruction manual reference “Rev 02” dated April 2010.

All the appliances will be fitted with a mechanical stop to prevent closure of the air control beyond 20mm from the closed position and 50 mm beyond the fully open position.

Section 1

The fireplace must be installed, maintained and operated in accordance with the instruction manual reference“INSTALLATION AND OPERATION MANUAL Arimax Bio 120-3000 kW” dated 30 March 2010.

Section 1

The fireplace must be installed, maintained and operated in accordance with the ECO 40 instruction manual, document Version 01-327332 dated October 2009.

Section 1

The fireplace must be installed, maintained and operated in accordance with the Unilux — 3 40 instruction manual, document Version 01 — 326587 dated August 2009.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s and Wood Energy Limited’s instructions entitled “Binder Equipment Installation, Commissioning and Maintenance” dated 17 May 2005, reference WEL-BinderManual rev0.doc, revision 0.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s and Wood Energy Limited’s instructions entitled “Binder Equipment Installation, Commissioning and Maintenance” dated 17 May 2005, reference WEL-BinderManual rev0.doc, revision 0.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s and Wood Energy Limited’s instructions entitled “Binder Equipment Installation, Commissioning and Maintenance” dated 17 May 2005, reference WEL-BinderManual rev0.doc, revision 0.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s and Wood Energy Limited’s instructions entitled “Binder Equipment Installation, Commissioning and Maintenance” dated 17 May 2005, reference WEL-BinderManual rev0.doc, revision 0.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s and Wood Energy Limited’s Operating instructions for Binder appliances referenced: “2009 July Binder O&M revision 8.doc Operation and Maintenance Manual, revision 8”, dated 15 July 2009.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s and Wood Energy Limited’s Operating instructions for Binder appliances referenced: “2009 July Binder O&M revision 8.doc Operation and Maintenance Manual, revision 8”, dated 15 July 2009.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s and Wood Energy Limited’s Operating instructions for Binder appliances referenced: “2009 July Binder O&M revision 8.doc Operation and Maintenance Manual, revision 8”, dated 15 July 2009.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated April 2005, reference Bedienun-gsanleitung Englisch v2.0 doc.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated April 2005, reference Bedienun-gsanleitung Englisch v2.0 doc.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instruction manual reference “91-62351” dated July 2009.

Section 1

The fireplace must be installed, maintained and operated in accordance with the installation and use instruction manual reference “COVE1SR01.-10 Issue A”.

An adjustment of the air control such that the minimum closure of the air control is equivalent to that found with the control pushed in 15mm from the fully open position.

Section 1

The fireplace must be installed, maintained and operated in accordance with the installation and use instruction manual reference “Tor 02.10 Issue A”.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s installation manual for the Classic Pellet Boilers reference “No. 22, Pellet Boilers, Type Classic 25, 31, 35, 40, 49, 60, reference BA Classic 25L-60L Nr 21 0508”.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions entitled “Operating Instructions Clearview Vision/Vision Inset/Pioneer & Solution” dated 1 July 2006, reference V1/42, stamped and signed “Smoke Control”.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s installation instructions IAV SE/EX 0726-6 611821 Lighting instruction BAV SA/EX 0717-2 611820.

A permanent stop must be in place on the air inlet to prevent closure beyond a minimum air open position.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s installation instructions IAV SE/EX 0740-1 511911.

A permanent stop must be in place on the air inlet to prevent closure beyond a minimum air open position.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instruction manual references “Cove2SR 07.09 IssB” dated July 2009.

A permanent stop must be in place on air control to prevent closure beyond 14mm from the fully closed position.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 20 February 2007, reference 161 505 27 06/1.

Section 1

The fireplace must be installed, maintained and operated in accordance with the instruction manual references “SE Selbourne 5 Issue 1” dated August 2009.

All appliances will be fitted with a mechanical stop to prevent closure beyond the 50% open position when sold into smoke control areas.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions, reference “PM250 Issue 1”.

A permanent stop must be in place on the secondary air inlet to prevent closure beyond the 75% open position.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 5 August 1998, reference A/22160 as amended by those dated 4 December 2004, reference D13.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 5 August 1998, reference A/22160 as amended by those dated 4 December 2004, reference D13.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 5 August 1998, reference A/22160 as amended by those dated 4 October 2004, reference GHD/DUN4B/1.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 4 December 2004, reference D13W.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 4 December 2004, reference D13W together with the manufacturer’s instructions dated 4 October 2004, reference GHD/DUN4B/1.

Section 1

The fireplace must be installed, maintained and operated in accordance with the instruction manual reference “ EW1MF technical manual” dated February 2009.

When the primary air control is in the closed position, it remains permanently open by 5mm and is prevented from closing fully by a screw.

Section 1

The fireplace must be installed, maintained and operated in accordance with the instruction manual reference “02/10” dated 10 February 2010.

The fitting of a system that prevents the closure of the secondary air flaps to be less than 4mm (3 Turns) open position should be implemented.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s installation manual dated November 2009, reference IMENP 10-35 November 2009 for the Firefox pellet boiler.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s installation manual dated November 2009, reference IMPK PK 15/25 11/2009 EN for the Firefox pellet boiler.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s installation manual dated November 2009, reference IMPK PK 45 11/2009 EN for the Firefox pellet boiler.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instruction manual dated February 2009, reference 100 SE Issue 1.

Section 1

The fireplace must be installed, maintained and operated in accordance with the instruction manual references “Esse 125SE Issue 1” dated Awst 2009.

All appliances will be fitted with a mechanical stop to prevent closure beyond the 50% open position when sold into smoke control areas.

Section 1

The fireplace must be installed, maintained and operated in accordance with the installation and operation manual reference “1622/Integra INSET revision c” dated July 2010.

All appliances used in smoke control areas must be fitted with a mechanical stop to fix secondary air control fully open.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions “Operating manual” reference Version 1/2010/Rev. 4.21.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 5 March 2007, reference 004275101 011.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 2 October 2006, reference 004275115 REV 005.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 28 August 2006, reference 004275128 REV 002.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated 12 July 2006, reference 004275110 REV 011.

Section 1

The fireplace must be installed, maintained and operated in accordance with the instruction manual references “FFXCBA” dated January 2010.

Section 1

The fireplace must be installed, maintained and operated in accordance with the instruction manual references “Issue 03” dated March 10.

The fitting of a system that prevents the closure of the secondary air control beyond the 3.5mm open position should be implemented.

Section 1

The fireplace must be installed, maintained and operated in accordance with the manufacturer’s instructions dated June 2005, reference “Bedienun-gsanleitung Firematic V 1.1 ENG doc”.

Section 1

The fireplace must be installed, maintained and operated in accordance with Instruction manual references “05.007 Operating Instructions – FM (1Ph) 20 35 45 60 v2.3” dated “Awst 2009”.

Cite this legislation