§ 465.01Applicability.
This part applies to any coil coating facility or to any canmaking facility that discharges pollutants to waters of the United States or that introduces pollutants to a publicly owned treatment works.
資料由法律人 LawPlayer整理提供·U.S. federal law / curated by LawPlayer from GPO govinfo & eCFR
CFR Regulation
COIL COATING POINT SOURCE CATEGORY
§ 465.02General definitions.
In addition to the definitions set forth in 40 CFR part 401, the following definitions apply to this part:
(a) “Coil” means a strip of basis material rolled into a roll for handling.
(b) “Coil coating ” means the process of converting basis material strip into coated stock. Usually cleaning, conversion coating, and painting are performed on the basis material. This regulation covers processes which perform any two or more of the three operations.
(c) “Basis material” means the coiled strip which is processed.
(d) “Area processed” means the area actually exposed to process solutions. Usually this includes both sides of the metal strip.
(e) “Steel basis material” means cold rolled steel, hot rolled steel, and chrome, nickel and tin coated steel which are processed in coil coating.
(f) “Galvanized basis material” means zinc coated steel, galvalum, brass and other copper base strip which is processed in coil coating.
(g) “Aluminum basis material” means aluminum, aluminum alloys and aluminum coated steels which are processed in coil coating.
(h) The term “can” means a container formed from sheet metal and consisting of a body and two ends or a body and a top.
(i) The term “canmaking” means the manufacturing process or processes used to manufacture a can from a basic metal.
(j) The term “Total Toxic Organics (TTO)” shall mean the sum of the mass of each of the following toxic organic compounds which are found at a concentration greater than 0.010 mg/1.
1,1,1-Trichloroethane
1,1-Dichloroethane
1,1,2,2-Tetrachloroethane
Bis (2-chloroethyl) ether
Chloroform
1,1-Dichloroethylene
Methylene chloride (dichloromethane)
Pentachlorophenol
Bis (2-ethylhexyl) phthalate
Butyl benzyl-phthalate
Di-N-butyl phthalate
Phenanthrene
Tetrachloroethylene
Toluene
§ 465.03Monitoring and reporting requirements.
The following special monitoring requirements apply to all facilities controlled by this regulation.
(a) Periodic analyses for cyanide are not required when both of the following conditions are met:
(1) The first wastewater sample taken in each calendar year has been analyzed and found to contain less than 0.07 mg/l cyanide
(2) The owner or operator of the coil coating facility certifies in writing to the POTW authority or permit issuing authority that cyanide is not used in the coil coating process.
(b) The “monthly average” regulatory values shall be the basis for the monthly average discharge limits in direct discharge permits and for pretreatment standards. Compliance with the monthly discharge limit is required regardless of the number of samples analyzed and averaged.
(c) The analytical method required for determination of petroleum hydrocarbons (non-polar material) is given under the listing for “oil and grease” at 40 CFR 136.3(a), Table IB and must be used after December 31, 2005.
(d) The owner or operator of any canmaking facility subject to the provisions of this regulation shall advise the permit issuing authority or POTW authority and the EPA Office of Water Regulations and Standards, Washington, DC 20460 whenever it has been decided that the plant will manufacture cans from an aluminum alloy containing less than 1.0 percent manganese. Such notification shall be made in writing, not less than 30 days in advance of the scheduled production and shall provide the chemical analysis of the alloy and the expected period of use.
(Approved by the Office of Management and Budget under control number 2040-0033)
§ 465.04Compliance date for PSES.
(a) For subparts A, B, and C the compliance date for Pretreatment Standards for Existing Source (PSES) is December 1, 1985.
(b) For subpart D, the compliance date for Pretreatment Standards for Existing Sources will be as soon as possible, but in no case later than November 17, 1986.
§ 465.10Applicability; description of the steel basis material subcategory.
This subpart applies to discharges to waters of the United States, and introductions of pollutants into publicly owned treatment works from coil coating of steel basis material coils.
§ 465.11Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available.
Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available:
Subpart A
Pollutant or pollutant property
BPT effluent limitations
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
1.16
(0.24)
0.47
(0.096)
Cyanide
0.80
(0.17)
0.33
(0.068)
Zinc
3.66
(0.75)
1.54
(0.32)
Iron
3.39
(0.70)
1.74
(0.36)
Oil and grease
55.1
(11.3)
33.1
(6.77)
TSS
113.0
(23.1)
55.1
(11.3)
pH
( 1 )
( 1 )
( 1 )
( 1 )
1 Within the range of 7.5 to 10.0 at all times.
§ 465.12Effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable.
Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable:
Subpart A
Pollutant or pollutant property
BAT effluent limitations
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.50
(0.10)
0.20
(0.041)
Cyanide
0.34
(0.07)
0.14
(0.029)
Zinc
1.56
(0.32)
0.66
(0.14)
Iron
1.45
(0.30)
0.74
(0.15)
§ 465.13New source performance standards.
The following standards of performance establish the quantity or quality of pollutants or pollutant properties, controlled by this section, which may be discharged by a new source subject to the provisions of this subpart:
Subpart A
Pollutant or pollutant property
NSPS
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.12
(0.024)
0.047
(0.01)
Cyanide
0.063
(0.013)
0.025
(0.005)
Zinc
0.33
(0.066)
0.14
(0.027)
Iron
0.39
(0.086)
0.20
(0.041)
Oil and grease
3.16
(0.65)
3.16
(0.65)
TSS
4.74
(0.97)
3.79
(0.78)
pH
( 1 )
( 1 )
( 1 )
( 1 )
1 Within the range of 7.5 to 10.0 at all times.
§ 465.14Pretreatment standards for existing sources.
Except as provided in 40 CFR 403.7 and 403.13, any existing source subject to this subpart which introduces pollutants into a publicly owned treatment works must comply with 40 CFR part 403 and achieve the following retreatment standards for existing sources. The mass of wastewater pollutants in coil coating process wastewater introduced into a POTW shall not exceed the following values:
Subpart A
Pollutant or pollutant property
PSES
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pound per 1 million ft 2 ) of area processed
Chromium
0.50
(0.10)
0.20
(0.041)
Cyanide
0.34
(0.07)
0.14
(0.029)
Zinc
1.56
(0.32)
0.66
(0.14)
§ 465.15Pretreatment standards for new sources.
Except as provided in CFR 403.7, any new source subject to this subpart which introduces pollutants into a publicly owned treatment works must comply with 40 CFR part 403 and achieve the following pretreatment standards for new sources. The mass of wastewater pollutants in coil coating process wastewater introduced into a POTW shall not exceed the following values:
Subpart A
Pollutant or pollutant property
PSNS
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.12
(0.024)
0.047
(0.01)
Cyanide
0.063
(0.013)
0.025
(0.005)
Zinc
0.33
(0.066)
0.14
(0.027)
§ 465.20Applicability; description of the galvanized basis material subcategory.
This subpart applies to discharges to waters of the United States and introductions of pollutants into publicly owned treatment works from coil coating of galvanized basis material coils.
§ 465.21Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available.
Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available:
Subpart B
Pollutant or pollutant property
BPT effluent limitations
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
1.10
(0.23)
0.45
(0.091)
Copper
4.96
(1.02)
2.61
(0.54)
Cyanide
0.76
(0.16)
0.32
(0.064)
Zinc
3.47
(0.71)
1.46
(0.30)
Iron
3.21
(0.66)
1.65
(0.34)
Oil and grease
52.2
(10.7)
31.3
(6.42)
TSS
107.0
(21.9)
52.2
(10.7)
pH
( 1 )
( 1 )
( 1 )
( 1 )
1 Within the range of 7.5 to 10.0 at all times.
§ 465.22Effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable.
Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable:
Subpart B
Pollutant or pollutant property
BAT effluent limitations
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.37
(0.077)
0.16
(0.031)
Copper
1.71
(0.35)
0.90
(0.19)
Cyanide
0.26
(0.053)
0.11
(0.022)
Zinc
1.20
(0.25)
0.51
(0.11)
Iron
1.10
(0.23)
0.57
(0.12)
§ 465.23New source performance standards.
The following standards of performance establish the quantity or quality of pollutants or pollutant properties, controlled by this section which may be discharged by a new source subject to the provisions of this subpart:
Subpart B
Pollutant or pollutant property
NSPS
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.13
(0.027)
0.052
(0.011)
Copper
0.44
(0.090)
0.21
(0.043)
Cyanide
0.07
(0.015)
0.028
(0.006)
Zinc
0.35
(0.08)
0.15
(0.030)
Iron
0.43
(0.09)
0.22
(0.045)
Oil and grease
3.43
(0.71)
3.43
(0.702)
TSS
5.15
(1.06)
4.12
(0.84)
pH
( 1 )
( 1 )
( 1 )
( 1 )
1 Within the range of 7.5 to 10.0 at all times.
§ 465.24Pretreatment standards for existing sources.
Except as provided in 40 CFR 403.7 and 403.13, any existing source subject to this subpart which introduces pollutants into a publicly owned treatment works must comply with 40 CFR part 403 and achieve the following pretreatment standards for existing sources. The mass of wastewater pollutants in coil coating process wastewater introduced into a POTW shall not exceed the following values:
Subpart B
Pollutant or pollutant property
PSES
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.37
(0.077)
0.16
(0.031)
Copper
1.71
(0.35)
0.90
(0.19)
Cyanide
0.26
(0.053)
0.11
(0.022)
Zinc
1.20
(0.25)
0.51
(0.11)
§ 465.25Pretreatment standards for new sources.
Except as provided in 40 CFR 403.7, any new source subject to this subpart which introduces pollutants into a publicly owned treatment works must comply with 40 CFR part 403 and achieve the following pretreatment standards for new sources. The mass of wastewater pollutants in coil coating process wastewater introduced into a POTW shall not exceed the following values.
Subpart B
Pollutant or pollutant property
PSNS
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.13
(0.027)
0.052
(0.011)
Copper
0.44
(0.090)
0.21
(0.043)
Cyanide
0.07
(0.015)
0.028
(0.006)
Zinc
0.35
(0.072)
0.15
(0.030)
§ 465.30Applicability; description of the aluminum basis material subcategory.
This subpart applies to discharges to waters of the United States and introductions of pollutants into publicly owned treatment works from coil coating of aluminum basis material coils.
§ 465.31Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available.
Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available:
Subpart C
Pollutant or pollutant property
BPT Effluent limitations
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
1.42
(0.29)
0.58
(0.12)
Cyanide
0.98
(0.20)
0.41
(0.083)
Zinc
4.48
(0.92)
1.89
(0.39)
Aluminum
15.3
(3.14)
6.26.
(1.28)
Oil and grease
67.3
(13.8)
40.4
(8.27)
TSS
138.0
(28.3)
67.3
(13.8)
pH
( 1 )
( 1 )
( 1 )
( 1 )
1 Within the range of 7.5 to 10.0 at all times.
§ 465.32Effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable.
Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable:
Subpart C
Pollutant or pollutant property
BAT Effluent limitations
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.42
(0.085)
0.17
(0.034)
Cyanide
0.29
(0.059)
0.12
(0.024)
Zinc
1.32
(0.27)
0.56
(0.12)
Aluminum
4.49
(0.92)
1.84.
(0.38)
§ 465.33New source performance standards.
The following standards of performance establish the quantity or quality of pollutants or pollutant properties, controlled by this section, which may be discharged by a new source subject to the provisions of this subpart.
Subpart C
Pollutant or pollutant property
NSPS
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.18
(0.037)
0.072
(0.015)
Cyanide
0.095
(0.020)
0.038
(0.008)
Zinc
0.49
(0.10)
0.20
(0.041)
Aluminum
1.44
(0.30)
0.59
(0.121)
Oil and Grease
4.75
(0.98)
4.75
(0.98)
TSS
7.13
(1.46)
5.70
(1.17)
pH
( 1 )
( 1 )
( 1 )
( 1 )
1 Within the range of 7.5 to 10.0 at all times.
§ 465.34Pretreatment standards for existing sources.
Except as provided in 40 CFR 403.7 and 403.13, any existing source subject to this subpart which introduces pollutants into a publicly owned treatment works must comply with 40 CFR part 403 and achieve the following pretreatment standards for existing sources. The mass of wastewater pollutants in coil coating process wastewater introduced into a POTW shall not exceed the following values:
Subpart C
Pollutant or pollutant property
PSES
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.42
(0.085)
0.17
(0.034)
Cyanide
0.29
(0.059)
0.12
(0.024)
Zinc
1.32
(0.27)
0.56
(0.12)
§ 465.35Pretreatment standards for new sources.
Except as provided in 40 CFR 403.7, any new source subject to this subpart which introduces pollutants into a publicly owned treatment works must comply with 40 CFR part 403 and achieve the following pretreatment standards for new sources. The mass of wastewater pollutants in coil coating process wastewater introduced into a POTW shall not exceed the following values:
Subpart C
Pollutant or pollutant property
PSNS
Maximum for any 1 day
Maximum for monthly average
mg/m 2 (pounds per 1 million ft 2 ) of area processed
Chromium
0.18
(0.037)
0.072
(0.015)
Cyanide
0.095
(0.02)
0.038
(0.008)
Zinc
0.49
(0.10)
0.20
(0.041)
§ 465.40Applicability; description of the canmaking subcategory.
This subpart applies to discharges to waters of the United States, and introductions of pollutants into publicly owned treatment works from the manufacturing of seamless can bodies, which are washed.
§ 465.41Effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available.
Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best practicable control technology currently available:
Subpart D—BPT Effluent Limitations
Pollutant or pollutant property
Maximum for any 1 day
Maximum for monthly average
g (lbs)/1,000,000 cans manufactured
Cr
94.60 (0.209)
38.70 (0.085)
Zn
313.90 (0.692)
131.15 (0.289)
Al
1382.45 (3.048)
688.00 (1.517)
F
12792.50 (28.203)
5676.00 (12.514)
P
3590.50 (7.916)
1468.45 (3.237)
O & G
4300.00 (9.480)
2580.00 (5.688)
TSS
8815.00 (19.434)
4192.50 (9.243)
pH
( 1 )
( 1 )
1 Within the range of 7.0 to 10 at all times.
§ 465.42Effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable.
Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the degree of effluent reduction attainable by the application of the best available technology economically achievable:
Subpart D—BAT Effluent Limitations
Pollutant or pollutant property
Maximum for any 1 day
Maximum for monthly average
g (lbs)/1,000,000 cans manufactured
Cr
36.92 (0.081)
15.10 (0.033)
Zn
122.49 (0.270)
51.18 (0.113)
Al
539.48 (1.189)
268.48 (0.592)
F
4992.05 (11.001)
2214.96 (4.883)
P
1401.13 (3.089)
573.04 (1.263)
§ 465.43New source performance standards.
The following standards of performance establish the quantity of pollutants or pollutant properties, controlled by this section, which may be discharged by a new source subject to the provisions of this subpart:
Subpart D—NSPS
Pollutant or pollutant property
Maximum for any 1 day
Maximum for monthly average
g (lbs)/1,000,000 cans manufactured
Cr
27.98 (0.062)
11.45 (0.025)
Zn
92.86 (0.205)
38.80 (0.086)
Al
408.95 (0.902)
203.52 (0.449)
F
3784.20 (8.343)
1679.04 (3.702)
P
1062.12 (2.342)
434.39 (0.958)
O & G
1272.00 (2.804)
763.20 (1.683)
TSS
2607.60 (5.749)
1240.20 (2.734)
pH
( 1 )
( 1 )
1 Within the range of 7.0 to 10 at all times.
§ 465.44Pretreatment standards for existing sources.
Except as provided in 40 CFR 403.7 and 403.13, any existing source subject to this subpart which introduces pollutants into a publicly owned treatment works must comply with 40 CFR part 403 and achieve the following pretreatment standards for exisiting sources.
Subpart D—PSES
Pollutant or pollutant property
Maximum for any 1 day
Maximum for monthly average
g (lbs)/1,000,000 cans manufactured
Cr
36.92 (0.081)
15.10 (0.033)
Cu
159.41 (0.351)
83.90 (0.185)
Zn
122.49 (0.270)
51.18 (0.113)
F
4992.05 (11.001)
2214.96 (4.883)
P
1401.13 (3.089)
573.04 (1.263)
Mn
57.05 (0.126)
24.33 (0.053)
TTO
26.85 (0.059)
12.59 (0.028)
O&G (for alternate monitoring)
1678.00 (3.699)
1006.80 (2.220)
§ 465.45Pretreatment standards for new sources.
Except as provided in 40 CFR 403.7 any new source subject to this subpart which introduces pollutants into a publicly owned treatment works must comply with 40 CFR part 403 and achieve the following pretreatment standards for new sources.
Subpart D—PSNS
Pollutant or pollutant property
Maximum for any 1 day
Maximum for monthly average
g (lbs)/1,000,000 cans manufactured
Cr
27.98 (0.0617)
11.45 (0.025)
Cu
120.84 (0.267)
63.60 (0.140)
Zn
92.86 (0.205)
38.80 (0.086)
F
3784.20 (8.345)
1679.04 (3.702)
P
1062.12 (2.342)
434.39 (0.958)
Mn
43.25 (0.095)
18.44 (0.041)
TTO
20.35 (0.045)
9.54 (0.0210)
O&G (for alternate monitoring)
1272.00 (2.804)
763.20 (1.683)
28 sections
Cite this law
COIL COATING POINT SOURCE CATEGORY (U.S.C.). Retrieved via LawPlayer, https://lawplayer.com/us/act/cfr-title-40-part-465
United States government works (U.S. Code, Code of Federal Regulations) are in the public domain under 17 U.S.C. § 105.
本頁資料來源：GPO govinfo / eCFR·整理提供：法律人 LawPlayer· lawplayer.com