APPROVAL AND PROMULGATION OF STATE PLANS FOR DESIGNATED FACILITIES AND POLLUTANTS

• Citation: 40 CFR Part 62
• Sections: 940

§ 62.01 Definitions.

As used in this part, all terms not defined herein shall have the meaning given to them in the Clean Air Act and in part 60 of this chapter.

§ 62.02 Introduction.

(a) This part sets forth the Administrator's approval and disapproval of State plans for the control of pollutants and facilities under section 111(d), and section 129 as applicable, of the Act, and the Administrator's promulgation of such plans or portions of plans thereof. Approval of a plan or any portion of a plan is based on a determination by the Administrator that it meets the requirements of section 111(d), and section 129 as applicable, of the Act and provisions of part 60 of this chapter.

(b)(1) If a State does not submit a complete, approvable plan, the Administrator may then promulgate a substitute plan or part of a plan. The promulgated provision, plus the approved parts of the State plan, constitute the applicable plan for purposes of the act.

(2) The part 60 subpart A of this chapter general provisions and appendices to part 60 apply to part 62, except as follows: 40 CFR 60.7(a)(1), 60.7(a)(3), and 60.8(a) and where special provisions set forth under the applicable subpart of this part shall apply instead of any conflicting provisions.

(c) The Administrator will promulgate substitute provisions for the disapproved regulatory provisions only. If a nonregulatory provision is disapproved, however, it will be noted in this part and a detailed explanation will be sent to the State.

(d) Section 62.12 provides information on availability of applicable plans. The Administrator and state and local agencies shall enforce

(1) Regulatory provisions of a plan approved or promulgated by the Administrator, and

(2) All permit conditions or denials issued in carrying out the approved or promulgated regulations for the review of designated facilities.

(e) Each State's plan is dealt with in a separate subpart, with separate headings for different pollutants and facilities. The plans shall include an introductory section identifying the plan by name and the date of its submittal. Additional sections are included as necessary to specifically identify disapproved provisions, to set forth reasons for disapproval, and to set forth provisions of the plan promulgated by the Administrator. Except as otherwise specified, all supplemental information submitted to the Administrator with respect to any plan has been submitted by the Governor of the State.

(f) Revisions to applicable plans will be included in this part when approved or promulgated by the Administrator.

(g) Substitute plans promulgated by the Administrator for States that do not have approved plans are contained in separate subparts that appear after the subparts for States. These Federal plans include sections identifying the applicability of the plan, emission limits, compliance schedules, recordkeeping and reporting, performance testing, and monitoring requirements.

§ 62.03 Extensions.

The Administrator may, whenever he determines necessary, extend the period for submission of any plan or plan revision or portion thereof.

§ 62.04 Approval status.

The approval status of each State's plan or portions thereof, are set forth in each subpart. All plans are approved unless specifically disapproved in the appropriate subpart.

§ 62.05 Legal authority.

(a) The Administrator's determination of the absence or inadequacy of legal authority required to be included in the plan is set forth in each subpart. This includes the legal authority of local agencies and State governmental agencies other than an air pollution control agency if such other agencies are assigned responsibility for carrying out a plan or portion thereof.

(b) No legal authority as such is promulgated by the Administrator. Where required regulatory provisions are not included in the plan by the State because of inadequate authority, substitute provisions are promulgated by the Administrator.

§ 62.06 Negative declarations.

A State may submit to the Administrator a letter certifying that no designated facilities exist in the State if such is the case. The negative declaration will be in lieu of a plan.

§ 62.07 Emission standards, compliance schedules.

(a) In each subpart, emission standards and compliance schedules which have been disapproved by the Administrator are identified, and those promulgated by the Administrator are set forth.

(b) The Administrator's approval or promulgation of any compliance schedule shall not affect the responsibility of the owner or operator to comply with any applicable emission limitation on or after the date for final compliance specified in the applicable schedule.

§ 62.08 Emission inventories and source surveillance.

(a) Each subpart identifies the plan provisions for source surveillance which are disapproved, and sets forth the Administrator's promulgation of necessary provisions for requiring designated sources to maintain records, make reports, and submit information.

(b) The Administrator will not promulgate provisions for disapproved State or local agency procedures for testing, inspection, investigation, or detection. However, detailed critiques of such portions will be provided to the State.

§ 62.09 Revision of plans by Administrator.

After notice and opportunity for public hearing in each affected State, the Administrator may revise any provision of an applicable plan if:

(a) The provision was promulgated by the Administrator and

(b) The plan, as revised, will be consistent with the Act and with the requirements of part 60, subpart B of this chapter.

§ 62.10 Submission to Administrator.

Except as otherwise provided in § 60.23 of this chapter, all requests, reports, applications, submittals, and other communications to the Administrator pursuant to this part shall be submitted in duplicate and addressed to the appropriate Regional office of the Environmental Protection Agency.” The Regional offices are as follows:

Table 1 to § 62.10

Region and jurisdiction

Address

I—Connecticut, Maine, Massachusetts, New Hampshire, Rhode Island, and Vermont

Director, Enforcement and Compliance Assurance Division, U.S. EPA Region I, 5 Post Office Square—Suite 100 (04-2), Boston, MA 02109-3912, Attn: Air Compliance Clerk.

II—New York, New Jersey, Puerto Rico, Virgin Islands

290 Broadway, New York, NY 10007-1866.

III—Delaware, District of Columbia, Maryland, Pennsylvania, Virginia, West Virginia

Air Protection Division, Mail Code 3AP00, 1650 Arch Street, Philadelphia, PA 19103-1129.

IV—Alabama, Florida, Georgia, Mississippi, Kentucky, North Carolina, South Carolina, Tennessee

61 Forsyth Street SW, Atlanta, GA 30303-3104.

V—Illinois, Indiana, Michigan, Minnesota, Ohio, Wisconsin

Mail Code A-17J, 77 West Jackson Blvd., Chicago, Il 60604-3590.

VI—Arkansas, Louisiana, New Mexico, Oklahoma, Texas

1201 Elm Street, Suite 500, Dallas, TX 75270.

VII—Iowa, Kansas, Missouri, Nebraska

Air and Waste Management Division 11201 Renner Boulevard, Lenexa, Kansas 66219.

VIII—Colorado, Montana, North Dakota, South Dakota, Utah, Wyoming

Director, Air Program, Office of Partnerships and Regulatory Assistance, Mail Code 8P-AR, 1595 Wynkoop Street, Denver, CO 80202-1129.

IX—Arizona, California, Hawaii, Nevada, the territories of American Samoa and Guam; the Commonwealth of the Northern Mariana Islands; the territories of Baker Island, Howland Island, Jarvis Island, Johnston Atoll, Kingman Reef, Midway Atoll, Palmyra Atoll, and Wake Islands; and certain U.S. Government activities in the freely associated states of the Republic of the Marshall Islands, the Federated States of Micronesia, and the Republic of Palau

75 Hawthorne Street, San Francisco, CA 94105.

§ 62.11 Severability.

The provisions promulgated in this part and the various applications thereof are distinct and severable. If any provision of this part or the application thereof to any person or circumstances is held invalid, such invalidity shall not affect other provisions or application of such provision to other persons or circumstances which can be given effect without the invalid provision or application.

§ 62.12 Availability of applicable plans.

Copies of the applicable plans will be available for public inspection at the following locations:

(a) EPA Docket Center, Room 3334, WJC West Building, 1301 Constitution Avenue NW, Washington, DC.

(b) The applicable EPA Regional office, at the address listed in § 62.10.

§ 62.13 Federal plans.

The Federal plans apply to owners and operators of affected facilities that are not covered by an EPA approved and currently effective State or Tribal plan. This Federal plan, or portions thereof, also applies to each affected facility located in any State or portion of Indian country whose approved State or Tribal plan for that area is subsequently vacated in whole or in part. Affected facilities are defined in each Federal plan.

(a) The substantive requirements of the municipal waste combustor Federal plan are contained in subpart FFF of this part. These requirements include emission limits, compliance schedules, testing, monitoring, and reporting and recordkeeping requirements.

(b) The substantive requirements of the municipal solid waste landfills Federal plan that implements 40 CFR part 60, subpart Cc of this chapter, are contained in subpart GGG of this part. These requirements include emission limits, compliance schedules, testing, monitoring, and reporting and recordkeeping requirements. After June 21, 2021, per paragraph (j) of this section, the substantive requirements of the municipal solid waste landfills Federal plan are contained in subpart OOO of this part and owners and operators of municipal solid waste landfills must comply with subpart OOO of this part or a state/tribal plan implementing 40 CFR part 60, subpart Cf of this chapter, instead of subpart GGG of this part.

(c) The substantive requirements of the hospital/ medical/infectious waste incinerator Federal plan are contained in subpart HHH of this part. These requirements include emission limits, compliance schedules, testing, monitoring and reporting and recordkeeping requirements.

(d) The substantive requirements of the commercial and industrial solid waste incineration units Federal plan are contained in subpart III of this part. These requirements include emission limits, compliance schedules, testing, monitoring, and reporting and recordkeeping requirements.

(e) The substantive requirements of the small municipal waste combustion unit Federal plan are contained in subpart JJJ of this part. These requirements include emission limits, compliance schedules, testing, monitoring, and reporting and recordkeeping requirements.

(f) [Reserved]

(g) The substantive requirements of the sewage sludge incineration units Federal plan are contained in subpart LLL of this part. These requirements include emission limits, compliance schedules, testing, monitoring, and reporting and recordkeeping requirements.

(h)-(i) [Reserved]

(j) The substantive requirements of the municipal solid waste landfills Federal plan that implements 40 CFR part 60, subpart Cf of this chapter, are contained in subpart OOO of this part. These requirements include emission limits, compliance schedules, testing, monitoring, and reporting and recordkeeping requirements.

§ 62.100 Identification of plan.

(a) Identification of plan. Alabama Designated Facility Plan (Section (d) Plan).

(b) The plan was officially submitted as follows. (1) Control of sulfuric acid mist emissions from existing sulfuric acid production units, submitted on May 18, 1980;

(2) Control of fluoride emissions from existing phosphate fertilizer plants, submitted on April 10, 1978.

(3) Alabama Department of Environmental Management Plan For the Control of Landfill Gas Emissions at Existing Municipal Solid Waste Landfills, submitted on January 6, 1998, by the Alabama Department of Environmental Management.

(4) State of Alabama Plan for Implementation of 40 CFR part 60, Subpart Cb, For Existing Municipal Waste Combustors, submitted on September 11, 1998, by the Alabama Department of Environmental Management.

(5) Alabama Department of Environmental Management Plan for the Control of Hospital/Medical/Infectious Waste Incinerators, submitted on April 20, 1999, by the Alabama Department of Environmental Management.

(c) Designated facilities. The plan applies to existing facilities in the following categories of sources:

(1) Sulfuric acid plants;

(2) Phosphate fertilizer plants.

(3) Existing municipal solid waste landfills.

(4) Existing municipal waste combustors.

(5) Existing hospital/medical/infectious waste incinerators.

Table 1 to Subpart FFF of Part 62 Table 1 to Subpart FFF of Part 62—Municipal Waste Combustor Units (MWC Units) Excluded From Subpart FFF 1

State

MWC units

Alabama

Existing facilities with an MWC unit capacity greater than 250 tons per day of municipal solid waste at the following MWC sites: (a) Solid Waste Disposal Authority of the City of Huntsville, Alabama.

Florida

Existing MWC units with capacity to combust more than 250 tons per day of municipal solid waste.

Georgia

Existing facilities with a MWC unit capacity greater than 250 tons per day of municipal solid waste at the following MWC sites:

(a) Savannah Energy Systems Company, Savannah, Georgia.

Illinois

Existing MWC units located at Robbins Resource Recovery Center, Robbins, Illinois.

Maine

Existing facilities with an MWC unit capacity greater than 250 tons per day of municipal solid waste at the following MWC sites: (a) Penobscot Energy Recovery Company, Orrington, Maine. (b) Maine Energy Recovery Company, Biddeford, Maine. (c) Regional Waste Systems, Inc., Portland, Maine.

Maryland

Existing MWC facilities with an MWC unit capacity greater than 250 tons per day of municipal solid waste.

Minnesota

All MWC units with unit capacities greater than 93.75 million British thermal units per hour on a heat input basis (250 tons per day) located in Minnesota.

New York

Existing MWC units with capacity to combust more than 250 tons per day of municipal solid waste.

Oklahoma

Existing MWC facilities with an MWC unit capacity greater than 250 tons per day of municipal solid waste at the following MWC site: Ogden-Martin Systems of Tulsa, Incorporated, 2122 South Yukon Avenue, Tulsa, Oklahoma.

Oregon

Existing facilities at the following MWC sites:

(a) Ogden Martin Systems, Marion County, Oregon.

(b) Coos County, Coos Bay, Oregon.

Pennsylvania

Existing MWC facilities with an MWC unit capacity greater than 250 tons per day of municipal solid waste at the following MWC site: (a) American Ref-fuel of Delaware Valley, LP (formerly Delaware County Resource Recovery facility), City of Chester, PA. (b) Harrisburg Materials, Energy, Recycling and Recovery Facility, City of Harrisburg, PA. (c) Lancaster County Solid Waste Management Authority, Conoy Township, Lancaster County, PA. (d) Montenay Montgomery Limited Partnership, Plymouth Township, Montgomery County, PA. (e) Wheelabrator Falls, Inc., Falls Township, Bucks County, PA. (f) York County Solid Waste and Refuse Authority, York, PA.

South Carolina

Existing facilities with a MWC unit capacity greater than 250 tons per day of municipal solid waste at the following MWC sites:

(a) Foster Wheeler Charleston Resource Recovery Facility, Charleston, South Carolina.

Tennessee

Existing MWC units with capacity to combust more than 250 tons per day of municipal solid waste.

1 Notwithstanding the exclusions in table 1 of this subpart, this subpart applies to affected facilities not regulated by an EPA approved and currently effective State or Tribal plan.

Table 2 to Subpart FFF of Part 62 Table 2 to Subpart FFF of Part 62—Nitrogen Oxides Requirements for Affected Facilities

Municipal waste combustor technology

Nitrogen oxides emission limit (parts per million by volume) a

Mass burn waterwall

205.

Mass burn rotary waterwall

250.

Refuse-derived fuel combustor

250.

Fluidized bed combustor

180.

Mass burn refractory combustors

No limit.

a Corrected to 7 percent oxygen, dry basis.

Table 3 to Subpart FFF of Part 62 Table 3 to Subpart FFF of Part 62—Municipal Waste Combustor Operating Requirements

Municipal waste combustor technology

Carbon monoxide emissions level (parts per million by volume) a

Averaging time (hrs) b

Mass burn waterwall

100

4

Mass burn refractory

100

4

Mass burn rotary refractory

100

24

Mass burn rotary waterwall

250

24

Modular starved air

50

4

Modular excess air

50

4

Refuse-derived fuel stoker

200

24

Fluidized bed, mixed fuel (wood/refuse-derived fuel)

200

c 24

Bubbling fluidized bed combustor

100

4

Circulating fluidized bed combustor

100

4

Pulverized coal/refuse-derived fuel mixed fuel-fired combustor

150

4

Spreader stoker coal/refuse-derived fuel mixed fuel-fired combustor

200

24

a Measured at the combustor outlet in conjunction with a measurement of oxygen concentration, corrected to 7 percent oxygen, dry basis. Calculated as an arithmetic average.

b Averaging times are 4-hour or 24-hour block averages.

c 24-hour block average, geometric mean.

Table 4 to Subpart FFF of Part 62 Table 4 to Subpart FFF of Part 62—Generic Compliance Schedule and Increments of Progress (Pre-1987 MWCs) a b

Affected facilities

Increment 1 Submit final control plan

Increment 2 Award contracts

Increment 3 Begin on-site construction

Increment 4 Complete on-site construction

Increment 5 Final compliance

Affected facilities that commenced construction, modification, or reconstruction on or before June 26, 1987 (All pollutants)

January 11, 1999

05/18/99

11/16/99

11/19/00

12/19/00

a Table 4 or 5 of this subpart applies to MWC units subject to the Federal plan except those with site-specific compliance schedules shown in Table 6 of this subpart.

b As an alternative to this schedule, the owner or operator may close the affected facility by December 19, 2000, complete the retrofit while the affected facility is closed, and achieve final compliance upon restarting. See §§ 62.14108(c), 62.14108(d), and 62.14109(i) of this subpart.

Table 5 to Subpart FFF of Part 62 Table 5 to Subpart FFF of Part 62—Generic Compliance Schedules and Increments of Progress

[Post-1987 MWCs] a b

Affected facilities

Increment 1 Submit final control plan

Increment 2 Award contracts

Increment 3 Begin on-site construction

Increment 4 Complete on-site construction

Increment 5 Final compliance

Affected facilities that commenced construction modification, or reconstruction after June 26, 1987:

1. Emission limits for Hg, dioxin/furan

NA c

NA c

NA c

NA c

11/12/99 or 1 year after permit issuance d e

2. Emission limits for SO 2 , HCl, PM, Pb, Cd, opacity CO, NO X

January 11, 1999

05/18/99

11/16/99

11/19/00

12/19/00.

a Table 4 or 5 of this subpart applies to MWC units subject to the Federal plan except those with site-specific compliance schedules shown in table 6 of this subpart.

b As an alternative to this schedule, the unit may close by December 19, 2000, complete retrofit while closed, and achieve final compliance upon restarting. See §§ 62.14108(c), 62.14108(d), and 62.14109(i) of this subpart.

c Because final compliance is achieved in 1 year, no increments of progress are required.

d Permit issuance is issuance of a revised construction permit or revised operating permit, if a permit modification is required to retrofit controls.

e Final compliance must be achieved no later than December 19, 2000, even if the date “1 year after permit issuance” exceeds December 19, 2000.

Table 6 to Subpart FFF of Part 62 Table 6 to Subpart FFF of Part 62—Site-Specific Compliance Schedules and Increments of Progress a

Affected facilities at the following MWC sites

City, State

Increment 1 Submit final control plan

Increment 2 Award contracts

Increment 3 Begin on-site construction

Increment 4 Complete on-site construction

Increment 5 Final compliance c

Stanislaus Resource Recovery Facility

Crows Landing, California

January 11, 1999

01/19/00

05/19/00

11/19/00

12/19/00

Southeast Resource Recovery Facility

Long Beach, California

January 11, 1999

04/30/99

10/31/99

04/30/00

12/19/00

All large MWC units

Maine

January 11, 1999

01/01/99

07/01/99

09/01/00

12/19/00

Baltimore Resco

Baltimore, Maryland

January 11, 1999

January 11, 1999

January 11, 1999

09/01/00

12/19/00

All large MWC units

New Jersey b

January 11, 1999

05/18/99

11/14/99

11/19/00

12/19/00

American Ref-Fuel

Delaware County, Pennsylvania

11/01/98

05/18/99

11/14/99

11/19/00

12/19/00

Montenay Energy Resource

Montgomery County, Pennsylvania

11/01/98

05/18/99

11/14/99

11/19/00

12/19/00

I-95 Energy/Resource Recovery Facility

Lorton, Virginia

January 11, 1999

10/15/99

03/01/00

11/19/00

12/19/00

New Hanover County, Unit 3A

Wilmington, North Carolina

09/15/99

03/01/00

07/01/00

11/19/00

12/19/00

a These schedules have been reviewed and determined to be acceptable by EPA.

b This schedule applies to HC1 SO 2 , PM, Pb, Cd, CO, and NO X . However, owners and operators of large MWC units in New Jersey have the option of reserving the portion of their control plan that addresses NO X . Owners and operators must submit the reserved portion to EPA by December 15, 1999.

c The owner or operator of an affected facility that began construction, modification, or reconstruction after June 26, 1987 must achieve final compliance with the mercury and dioxins/furans limits within 1 year after promulgation of subpart FFF (i.e., by 11/12/99) or 1 year after permit issuance. Permit issuance is issuance of a revised construction permit or revised operating permit if a permit modification is required to retrofit controls. Final compliance must be achieved no later than December 19, 2000, even if the date “1 year after permit issuance” exceeds December 19, 2000.

Table 1 to Subpart GGG of Part 62 Table 1 to Subpart GGG of Part 62—States That Have an Approved and Effective State Plan a

State plan

Effective date of state plan b

Alabama

12/07/98

Allegheny County, Pennsylvania

04/16/99

Arizona

11/19/99

California

11/22/99

Colorado

09/28/98

Delaware

11/16/99

Florida

08/03/99

Georgia

01/12/99

Illinois

01/22/99

Iowa

06/22/98

Kansas

05/19/98

Kentucky

06/21/99

Louisiana

10/28/97

Maryland

11/8/99

Minnesota

09/25/98

Missouri

06/23/98

Montana

09/08/98

Nashville, Tennessee

02/16/99

Nebraska

06/23/98

Nevada

11/19/99

New Mexico

02/10/98

New York

09/17/99

North Dakota

02/13/98

Ohio

10/06/98

Oklahoma

05/18/99

Oregon

08/25/98

South Carolina

10/25/99

South Dakota

08/02/99

Tennessee

11/29/99

Texas

08/16/99

Utah

03/16/98

Wyoming

07/31/98

a This table is provided as a matter of convenience and is not controlling in determining whether a MSW landfill is subject to the Federal plan. A MSW landfill is subject to this Federal plan if it commenced construction before May 30, 1991 and has not been modified or reconstructed on or after that date and is not covered by an approved and currently effective State or Tribal plan.

b The State plan is expected to become effective on the date indicated. However, if the State plan does not become effective on the date indicated, the Federal plan applies until the State plan becomes effective.

Table 2 to Subpart GGG of Part 62 Table 2 to Subpart GGG of Part 62—States That Submitted a Negative Declaration Letter a

State, locality, or portion of Indian country

Date of negative declaration

District of Columbia

09/11/97

New Hampshire

07/22/98

Philadelphia, Pennsylvania

02/27/96

Rhode Island

05/27/98

Vermont

08/20/96

a A MSW landfill with a design capacity equal to or greater than 2.5 million megagrams and 2.5 million cubic meters located in an area for which a negative declaration letter was submitted is subject to the Federal plan, notwithstanding the negative declaration letter and this table 2.

Table 3 to Subpart GGG of Part 62 Table 3 to Subpart GGG of Part 62—Generic Compliance Schedule and Increments of Progress a

Increment

Date

Increment 1—Submit final control plan

1 year after initial NMOC emission rate report or the first annual emission rate report showing NMOC emissions ≥50 Mg/yr. b

Increment 2—Award Contracts

20 months after initial NMOC emission rate report or the first annual emission rate report showing NMOC emissions ≥50 Mg/yr. b

Increment 3—Begin on-site construction

24 months after initial NMOC emission rate report or the first annual emission rate report showing NMOC emissions ≥50 Mg/yr. b

Increment 4—Complete on-site construction

30 months after initial NMOC emission rate report or the first annual emission rate report showing NMOC emissions ≥50 Mg/yr. b

Increment 5—Final compliance

30 months after initial NMOC emission rate report or the first annual emission rate report showing NMOC emissions ≥50 Mg/yr. b

a Table 3 of subpart GGG applies to landfills with design capacities ≥2.5 million megagrams and 2.5 million cubic meters that are subject to this subpart except those with site-specific compliance schedules shown in table 4 of subpart GGG.

b NMOC = nonmethane organic compounds Mg/yr = megagrams per year

Table 1 to Subpart HHH of Part 62 Table 1 to Subpart HHH of Part 62—Emission Limits for Small Rural, Small, Medium, and Large HMIWI

For the air pollutant

You must meet this emissions limit

With these units (7 percent oxygen, dry basis)

Using this averaging time a

And determining compliance using this method b

HMIWI size

Small rural

Small

Medium

Large

Particulate matter

87 (0.038)

66 (0.029)

46 (0.020) c 34 (0.015) d

25 (0.011)

Milligrams per dry standard cubic meter (grains per dry standard cubic foot)

3-run average (1-hour minimum sample time per run)

EPA Reference Method 5 of appendix A-3 of part 60, or EPA Reference Method M 26A or 29 of appendix A-8 of part 60

Carbon monoxide

20

20

5.5

11

Parts per million by volume

3-run average (1-hour minimum sample time per run)

EPA Reference Method 10 or 10B of appendix A-4 of part 60

Dioxins/furans

240 (100) or 5.1 (2.2)

16 (7.0) or 0.013 (0.0057)

0.85 (0.37) or 0.020 (0.0087)

9.3 (4.1) or 0.054 (0.024)

Nanograms per dry standard cubic meter total dioxins/furans (grains per billion dry standard cubic feet) or nanograms per dry standard cubic meter TEQ (grains per billion dry standard cubic feet)

3-run average (4-hour minimum sample time per run)

EPA Reference Method 23 of appendix A-7 of part 60

Hydrogen chloride

810

44 c 15 d

7.7

6.6

Parts per million by volume

3-run average (1-hour minimum sample time per run)

EPA Reference Method 26 or 26A of appendix A-8 of part 60

Sulfur dioxide

55

4.2

4.2

9.0

Parts per million by volume

3-run average (1-hour minimum sample time per run)

EPA Reference Method 6 or 6C of appendix A-4 of part 60

Nitrogen oxides

130

190

190

140

Parts per million by volume

3-run average (1-hour minimum sample time per run)

EPA Reference Method 7 or 7E of appendix A-4 of part 60

Lead

0.50 (0.22)

0.31 (0.14)

0.018 (0.0079)

0.036 (0.016)

Milligrams per dry standard cubic meter (grains per thousand dry standard cubic feet)

3-run average (1-hour minimum sample time per run)

EPA Reference Method 29 of appendix A-8 of part 60

Cadmium

0.11 (0.048)

0.017 (0.0074)

0.013 (0.0057)

0.0092 (0.0040)

Milligrams per dry standard cubic meter (grains per thousand dry standard cubic feet)

3-run average (1-hour minimum sample time per run)

EPA Reference Method 29 of appendix A-8 of part 60

Mercury

0.051 (0.0022)

0.014 (0.0061)

0.025 (0.011)

0.018 (0.0079)

Milligrams per dry standard cubic meter (grains per thousand dry standard cubic feet)

3-run average (1-hour minimum sample time per run)

EPA Reference Method 29 of appendix A-8 of part 60

a Except as allowed under §§ 62.14452(o)-(q) for HMIWI equipped with CEMS or continuous automated sampling systems.

b Does not include CEMS, continuous automated sampling systems, and approved alternative non-EPA test methods allowed under § 62.14452(d) and (m).

c Limits for those HMIWI for which construction or modification was commenced according to § 62.14400(a)(2)(i).

d Limits for those HMIWI for which construction or modification was commenced according to § 62.14400(a)(2)(ii).

Table 2 to Subpart HHH of Part 62 Table 2 to Subpart HHH of Part 62—Toxic Equivalency Factors

Dioxin/furan congener

Toxic equivalency factor

2,3,7,8-tetrachlorinated dibenzo-p-dioxin

1

1,2,3,7,8-pentachlorinated dibenzo-p-dioxin

1

1,2,3,4,7,8-hexachlorinated dibenzo-p-dioxin

0.1

1,2,3,7,8,9-hexachlorinated dibenzo-p-dioxin

0.1

1,2,3,6,7,8-hexachlorinated dibenzo-p-dioxin

0.1

1,2,3,4,6,7,8-heptachlorinated dibenzo-p-dioxin

0.01

Octachlorinated dibenzo-p-dioxin

0.0003

2,3,7,8-tetrachlorinated dibenzofuran

0.1

2,3,4,7,8-pentachlorinated dibenzofuran

0.3

1,2,3,7,8-pentachlorinated dibenzofuran

0.03

1,2,3,4,7,8-hexachlorinated dibenzofuran

0.1

1,2,3,6,7,8-hexachlorinated dibenzofuran

0.1

1,2,3,7,8,9-hexachlorinated dibenzofuran

0.1

2,3,4,6,7,8-hexachlorinated dibenzofuran

0.1

1,2,3,4,6,7,8-heptachlorinated dibenzofuran

0.01

1,2,3,4,7,8,9-heptachlorinated dibenzofuran

0.01

Octachlorinated dibenzofuran

0.0003

Table 3 to Subpart HHH of Part 62 Table 3 to Subpart HHH of Part 62—Operating Parameters To Be Monitored and Minimum Measurement and Recording Frequencies

Operating parameters to be monitored

Minimum frequency

HMIWI

Data measurement

Data recording

HMIWI with combustion control only

HMIWI with dry scrubber followed by FF

HMIWI with wet scrubber

HMIWI with dry scrubber followed by FF and wet scrubber

HMIWI with SNCR system

Maximum operating parameters:

Maximum charge rate

Once per charge

Once per charge

✓

✓

✓

✓

✓

Maximum FF inlet temperature

Continuous

Once per minute

✓

✓

Maximum flue gas temperature

Continuous

Once per minute

✓

✓

Minimum operating parameters:

Minimum secondary chamber temperature

Continuous

Once per minute

✓

✓

✓

✓

✓

Minimum dioxin/furan sorbent flow rate

Hourly

Once per hour

✓

✓

Minimum HCl sorbent flow rate

Hourly

Once per hour

✓

✓

Minimum mercury (Hg) sorbent flow rate

Hourly

Once per hour

✓

✓

Minimum pressure drop across the wet scrubber or minimum horsepower or amperage to wet scrubber

Continuous

Once per minute

✓

✓

Minimum scrubber liquor flow rate

Continuous

Once per minute

✓

✓

Minimum scrubber liquor pH

Continuous

Once per minute

✓

✓

Minimum reagent flow rate

Hourly

Once per hour

✓

Table 1 to Subpart III of Part 62 Table 1 to Subpart III of Part 62—Emission Limitations

For the air pollutant

You must meet this emission limitation a

Using this averaging time

And determining compliance using this method

Cadmium

0.004 milligrams per dry standard cubic meter

3-run average (1 hour minimum sample time per run)

Performance test (Method 29 of appendix A of part 60).

Carbon monoxide

157 parts per million by dry volume

3-run average (1 hour minimum sample time per run)

Performance test (Method 10, 10A, or 10B, of appendix A of part 60).

Dioxins/furans (toxic equivalency basis)

0.41 nanograms per dry standard cubic meter

3-run average (4 hour minimum sample time per run)

Performance test (Method 23 of appendix A of part 60).

Hydrogen chloride

62 parts per million by dry volume

3-run average (1 hour minimum sample time per run)

Performance test (Method 26A of appendix A of part 60).

Lead

0.04 milligrams per dry standard cubic meter

3-run (1 hour minimum sample time per run)

Performance test (Method 29 of appendix A of part 60).

Mercury

0.47 milligrams per dry standard cubic meter

3-run average (1 hour minimum sample time per run)

Performance test (Method 29 of appendix A of part 60).

Opacity

10 percent

6-minute averages

Performance test (Method 9 of appendix A of part 60).

Oxides of nitrogen

388 parts per million by dry volume

3-run average (1 hour minimum sample time per run)

Performance test (Methods 7, 7A, 7C, 7D, or 7E of appendix A of part 60).

Particulate matter

70 milligrams per dry standard cubic meter

3-run average (1 hour minimum sample time per run)

Performance test (Method 5 or 29 of appendix A of part 60).

Sulfur dioxide

20 parts per million by dry volume

3-run average (1 hour minimum sample time per run)

Performance test (Method 6 or 6c of appendix A of part 60).

a All emission limitations (except for opacity) are measured at 7 percent oxygen, dry basis at standard conditions.

Table 2 to Subpart III of Part 62 Table 2 to Subpart III of Part 62—Operating Limits for Wet Scrubbers

For these operating parameters

You must establish these operating limits

And monitor using these minimum frequencies

Data measurement

Data recording

Averaging time

Charge rate

Maximum charge rate

Continuous

Every hour

1. Daily (batch units) 2. 3-hour rolling (continuous and intermittent units) a

Pressure drop across the wet scrubber or amperage to wet scrubber

Minimum pressure drop or amperage

Continuous

Every 15 minutes

3-hour rolling a

Scrubber liquor flow rate

Minimum flow rate

Continuous

Every 15 minutes

3-hour rolling a

Scrubber liquor pH

Minimum pH

Continuous

Every 15 minutes

3-hour rolling a

a Calculated each hour as the average of the previous 3 operating hours.

Table 3 to Subpart III of Part 62 Table 3 to Subpart III of Part 62—Toxic Equivalency Factors

Dioxin/furan congener

Toxic equivalency factor

A. 2,3,7,8-tetrachlorinated dibenzo-p-dioxin

1

B. 12,3,7,8-pentachlorinated dibenzo-p-dioxin

0.5

C. 1,2,3,4,7,8-hexachlorinated dibenzo-p-dioxin

0.1

D. 1,2,3,7,8,9-hexachlorinated dibenzo-p-dioxin

0.1

E. 12,3,6,7,8-hexachlorinated dibenzo-p-dioxin

0.1

F. 1,2,3,4,6,7,8-heptachlorinated dibenzo-p-dioxin

0.01

G. 0ctachlorinated dibenzo-p-dioxin

0.001

H. 2,3,7,8-tetrachlorinated dibenzofuran

0.1

I. 2,3,4,7,8-pentachlorinated dibenzofuran

0.5

J. 1,2,3,7,8-pentachlorinated dibenzofuran

0.05

K. 1,2,3,4,7,8-hexachlorinated dibenzofuran

0.1

L. 1,2,3,6,7,8-hexachlorinated dibenzofuran

0.1

M. 1,2,3,7,8,9-hexachlorinated dibenzofuran

0.1

N. 2,3,4,6,7,8-hexachlorinated dibenzofuran

0.1

O. 1,2,3,4,6,7,8-heptachlorinated dibenzofuran

0.01

P. 1,2,3,4,7,8,9-heptachlorinated dibenzofuran

0.01

Q. 0ctachlorinated dibenzofuran

0.001

Table 4 to Subpart III of Part 62 Table 4 to Subpart III of Part 62—Summary of Reporting Requirements a

Report

Due date

Contents

Reference

A. Waste Management Plan

No later than April 5, 2004

Waste management plan

§ 62.14715.

B. Initial Test Report

No later than 60 days following the initial performance test

1. Complete test report for the initial performance test 2. The values for the site-specific operating limits. 3. Installation of bag leak detection systems for fabric filters.

§ 62.14720.

C. Annual report

No later than 12 months following the submission of the initial test report. Subsequent reports are to be submitted no more than 12 months following the previous report

1. Name and address 2. Statement and signature by responsible official. 3. Date of report. 4. Values for the operating limits. 5. If no deviations or malfunctions were reported, a statement that no deviations occurred during the reporting period. 6. Highest recorded 3-hour average and the lowest 3-hour average, as applicable, for each operating parameter recorded for the calendar year being reported

§§ 62.14725 and 62.14730. Subsequent reports are to be submitted no more than 12 months following the previous report.

7. Information for deviations or malfunctions recorded under § 62.14700(b)(6) and (c) through (e) 8. If a performance test was conducted during the reporting period, the results of the test. 9. If a performance test was not conducted during the reporting period, a statement that the requirements of § 62.14680(a) or (b) were met. 10. Documentation of periods when all qualified CISWI unit operators were unavailable for more than 8 hours but less than 2 weeks.

D. Emission Limitation or Operating Limit Deviation Report

By August 1 of that year for data collected during the first half of the calendar year By February 1 of the following year for data collected during the second half of the calendar year.

1. Dates and times of deviations 2. Averaged and recorded data for these dates. 3. Duration and causes for each deviation and the corrective actions taken. 4. Copy of operating limit monitoring data and any test reports. 5. Dates, times, and causes for monitor downtime incidents. 6. Whether each deviation occurred during a period of startup, shutdown, or malfunction.

§§ 62.14735 and 62.14740.

E. Qualified Operator Deviation Notification

Within 10 days of deviation

1. Statement of cause of deviation. 2. Description of efforts to have an accessible qualified operator. 3. The date a qualified operator will be accessible.

§ 62.14745(a)(1).

F. Qualified Operator Deviation Status Report

Every 4 weeks following deviation.

1. Description of efforts to have an accessible qualified operator 2. The date a qualified operator will be accessible. 3. Request for approval to continue operation.

§ 62.14745(a)(2).

G. Qualified Operator Deviation Notification of Resumed Operation

Prior to resuming operation

Notification that you are resuming operation

§ 62.14745(b).

a This table is only a summary, see the referenced sections of the rule for the complete requirements.

Table 1 to Subpart LLL of Part 62 Table 1 to Subpart LLL of Part 62—Compliance Schedule for Existing Sewage Sludge Incineration Units

Comply with these requirements

By this date

1—Submit final control plan

March 21, 2016, for all units except East Bank Wastewater Treatment Plant, New Orleans, Louisiana, and Bayshore Regional Wastewater Treatment Plant in Union Beach, Monmouth County, NJ.

2—Final compliance

For East Bank Wastewater Treatment Plant, New Orleans, Louisiana, and Bayshore Regional Wastewater Treatment Plant in Union Beach, Monmouth County, NJ, March 21, 2017.

Table 2 to Subpart LLL of Part 62 Table 2 to Subpart LLL of Part 62—Emission Limits and Standards for Existing Fluidized Bed Sewage Sludge Incineration Units

For the air pollutant

You must meet this emission limit 1

Using these averaging methods and minimum sampling volumes or durations

And determining compliance using this method

Particulate matter

18 milligrams per dry standard cubic meter

3-run average (collect a minimum volume of 1 dry standard cubic meters sample per run)

Performance test (Method 5 at 40 CFR part 60, appendix A-3; Method 26A or Method 29 at 40 CFR part 60, appendix A-8).

Hydrogen chloride

0.51 parts per million by dry volume

3-run average (Collect a minimum volume of 1 dry standard cubic meters per run)

Performance test (Method 26A at 40 CFR part 60, appendix A-8).

Carbon monoxide

64 parts per million by dry volume

3-run average (collect sample for a minimum duration of one hour per run)

Performance test (Method 10, 10A, or 10B at 40 CFR part 60, appendix A-4).

Dioxins/furans (total mass basis); or

1.2 nanograms per dry standard cubic meter (total mass basis); or

3-run average (collect a minimum volume of 1 dry standard cubic meters per run)

Performance test (Method 23 at 40 CFR part 60, appendix A-7).

Dioxins/furans (toxic equivalency basis) 2

0.10 nanograms per dry standard cubic meter (toxic equivalency basis)

Mercury

0.037 milligrams per dry standard cubic meter

3-run average (For Method 29 and ASTM D6784-02 (Reapproved 2008) 3 , collect a minimum volume of 1 dry standard cubic meters per run. For Method 30B, collect a minimum sample as specified in Method 30B at 40 CFR part 60, appendix A-8)

Performance test (Method 29 at 40 CFR part 60, appendix A-8; Method 30B at 40 CFR part 60, appendix A-8; or ASTM D6784-02 (Reapproved 2008). 3 5

Oxides of nitrogen

150 parts per million by dry volume

3-run average (Collect sample for a minimum duration of one hour per run)

Performance test (Method 7 or 7E at 40 CFR part 60, appendix A-4).

Sulfur dioxide

15 parts per million by dry volume

3-run average (For Method 6, collect a minimum volume of 60 liters per run. For Method 6C, collect sample for a minimum duration of one hour per run)

Performance test (Method 6 or 6C at 40 CFR part 40, appendix A-4; or ANSI/ASME PTC-19.10-1981. 3 4

Cadmium

0.0016 milligrams per dry standard cubic meter

3-run average (collect a minimum volume of 1 dry standard cubic meters per run)

Performance test (Method 29 at 40 CFR part 60, appendix A-8). Use GFAAS or ICP/MS for the analytical finish.

Lead

0.0074 milligrams per dry standard cubic meter

3-run average (collect a minimum volume of 1 dry standard cubic meters sample per run)

Performance test (Method 29 at 40 CFR part 60, appendix A-8. Use GFAAS or ICP/MS for the analytical finish.

Fugitive emissions from ash handling

Visible emissions of combustion ash from an ash conveying system (including conveyor transfer points) for no more than 5 percent of any compliance test hourly observation period

Three 1-hour observation periods

Visible emission test (Method 22 at 40 CFR part 60, appendix A-7).

1 All emission limits are measured at 7-percent oxygen, dry basis at standard conditions.

2 You have the option to comply with either the dioxin/furan emission limit on a total mass basis or the dioxin/furan emission limit on a toxic equivalency basis.

3 The Director of the Federal Register approves these incorporations by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. You may inspect these standards at U.S. Environmental Protection Agency, 1200 Pennsylvania Avenue NW., Washington, DC 20460, [phone], http://www.epa.gov. You may also inspect a copy at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: {HYPERLINK “ http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html ”}.

4 ANSI/ASME PTC 19.10-1981, Flue and Exhaust Gas Analyses [Part 10, Instruments and Apparatus]. American Society of Mechanical Engineers (ASME), Three Park Avenue, New York, NY 10016-5990 (Phone: [phone]; Web site: https://www.asme.org/ ).

5 ASTM D6784-02 (Reapproved 2008) Standard Test Method for Elemental, Oxidized, Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired Stationary Sources (Ontario Hydro Method), [approved April 1, 2008]. ASTM International, 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428-2959; ProQuest, 300 North Zeeb Road, Ann Arbor, MI 48106 (Phone: [phone]; Web site: http://www.astm.org/ ).

Table 3 to Subpart LLL of Part 62 Table 3 to Subpart LLL of Part 62—Emission Limits and Standards for Existing Multiple Hearth Sewage Sludge Incineration Units

For the air pollutant

You must meet this emission limit 1

Using these averaging methods and minimum sampling volumes or durations

And determining compliance using this method

Particulate matter

80 milligrams per dry standard cubic meter

3-run average (collect a minimum volume of 0.75 dry standard cubic meters per run)

Performance test (Method 5 at 40 CFR part 60, appendix A-3; Method 26A or Method 29 at 40 CFR part 60, appendix A-8).

Hydrogen chloride

1.2 parts per million by dry volume

3-run average (For Method 26, collect a minimum volume of 200 liters per run. For Method 26A, collect a minimum volume of 1 dry standard cubic meters per run)

Performance test (Method 26 or 26A at 40 CFR part 60, appendix A-8).

Carbon monoxide

3,800 parts per million by dry volume

3-run average (collect sample for a minimum duration of one hour per run)

Performance test (Method 10, 10A, or 10B at 40 CFR part 60, appendix A-4).

Dioxins/furans (total mass basis)

5.0 nanograms per dry standard cubic meter; or

3-run average (collect a minimum volume of 1 dry standard cubic meters per run)

Performance test (Method 23 at 40 CFR part 60, appendix A-7).

Dioxins/furans (toxic equivalency basis). 2

0.32 nanograms per dry standard cubic meter

Mercury

0.28 milligrams per dry standard cubic meter

3-run average (For Method 29 and ASTM D6784-02 (Reapproved 2008), 3 collect a minimum volume of 1 dry standard cubic meters per run. For Method 30B, collect a minimum sample as specified in Method 30B at 40 CFR part 60, appendix A-8)

Performance test (Method 29 at 40 CFR part 60, appendix A-8; Method 30B at 40 CFR part 60, appendix A-8; or ASTM D6784-02 (Reapproved 2008). 3 5

Oxides of nitrogen

220 parts per million by dry volume

3-run average (Collect sample for a minimum duration of one hour per run)

Performance test (Method 7 or 7E at 40 CFR part 60, appendix A-4).

Sulfur dioxide

26 parts per million by dry volume

3-run average (For Method 6, collect a minimum volume of 200 liters per run. For Method 6C, collect sample for a minimum duration of one hour per run)

Performance test (Method 6 or 6C at 40 CFR part 40, appendix A-4; or ANSI/ASME PTC 19.10-1981. 3 4

Cadmium

0.095 milligrams per dry standard cubic meter

3-run average (collect a minimum volume of 1 dry standard cubic meters per run)

Performance test (Method 29 at 40 CFR part 60, appendix A-8).

Lead

0.30 milligrams per dry standard cubic meter

3-run average (collect a minimum volume of 1 dry standard cubic meters per run)

Performance test (Method 29 at 40 CFR part 60, appendix A-8.

Fugitive emissions from ash handling

Visible emissions of combustion ash from an ash conveying system (including conveyor transfer points) for no more than 5 percent of any compliance test hourly observation period

Three 1-hour observation periods

Visible emission test (Method 22 at 40 CFR part 60, appendix A-7).

1 All emission limits are measured at 7-percent oxygen, dry basis at standard conditions.

2 You have the option to comply with either the dioxin/furan emission limit on a total mass basis or the dioxin/furan emission limit on a toxic equivalency basis.

3 The Director of the Federal Register approves these incorporations by reference in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. You may inspect these standards at U.S. Environmental Protection Agency, 1200 Pennsylvania Avenue NW., Washington, DC 20460, [phone], http://www.epa.gov. You may also inspect a copy at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

4 ANSI/ASME PTC 19.10-1981, Flue and Exhaust Gas Analyses [Part 10, Instruments and Apparatus]. American Society of Mechanical Engineers (ASME), Three Park Avenue, New York, NY 10016-5990 (Phone: [phone]; Web site: https://www.asme.org/ ).

5 ASTM D6784-02 (Reapproved 2008) Standard Test Method for Elemental, Oxidized, Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired Stationary Sources (Ontario Hydro Method), [approved April 1, 2008]. ASTM International, 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken, PA 19428-2959; ProQuest, 300 North Zeeb Road, Ann Arbor, MI 48106 (Phone: [phone]; Web site: http://www.astm.org/ ).

Table 4 to Subpart LLL of Part 62 Table 4 to Subpart LLL of Part 62—Operating Parameters for Existing Sewage Sludge Incineration Units 1

For these operating parameters

You must establish these operating limits

And monitor using these minimum frequencies

Data measurement

Data recording 2

Data averaging period for compliance

All sewage sludge incineration units

Combustion chamber operating temperature (not required if afterburner temperature is monitored)

Minimum combustion chamber operating temperature or afterburner temperature

Continuous

Every 15 minutes

12-hour block.

Fugitive emissions from ash handling

Site-specific operating requirements

Not applicable

Not applicable

Not applicable.

Scrubber

Pressure drop across each wet scrubber

Minimum pressure drop

Continuous

Every 15 minutes

12-hour block.

Scrubber liquid flow rate

Minimum flow rate

Continuous

Every 15 minutes

12-hour block.

Scrubber liquid pH

Minimum pH

Continuous

Every 15 minutes

3-hour block.

Fabric Filter

Alarm time of the bag leak detection system alarm

Maximum alarm time of the bag leak detection system alarm (this operating limit is provided in § 60.4850 and is not established on a site-specific basis)

Electrostatic precipitator

Secondary voltage of the electrostatic precipitator collection plates

Minimum power input to the electrostatic precipitator collection plates

Continuous

Hourly

12-hour block.

Secondary amperage of the electrostatic precipitator collection plates

Effluent water flow rate at the outlet of the electrostatic precipitator

Minimum effluent water flow rate at the outlet of the electrostatic precipitator

Hourly

Hourly

12-hour block.

Activated carbon injection

Mercury sorbent injection rate

Minimum mercury sorbent injection rate

Hourly

Hourly

12-hour block.

Dioxin/furan sorbent injection rate

Minimum dioxin/furan sorbent injection rate.

Carrier gas flow rate or carrier gas pressure drop

Minimum carrier gas flow rate or minimum carrier gas pressure drop

Continuous

Every 15 minutes

12-hour block.

Afterburner

Temperature of the afterburner combustion chamber

Minimum temperature of the afterburner combustion chamber

Continuous

Every 15 minutes

12-hour block.

1 As specified in § 62.15985, you may use a continuous emissions monitoring system or continuous automated sampling system in lieu of establishing certain operating limits.

2 This recording time refers to the minimum frequency that the continuous monitor or other measuring device initially records data. For all data recorded every 15 minutes, you must calculate hourly arithmetic averages. For all parameters, you use hourly averages to calculate the 12-hour or 3-hour block average specified in this table for demonstrating compliance. You maintain records of 1-hour averages.

Table 5 to Subpart LLL of Part 62 Table 5 to Subpart LLL of Part 62—Toxic Equivalency Factors

Dioxin/furan isomer

Toxic equivalency factor

2,3,7,8-tetrachlorinated dibenzo-p-dioxin

1

1,2,3,7,8-pentachlorinated dibenzo-p-dioxin

1

1,2,3,4,7,8-hexachlorinated dibenzo-p-dioxin

0.1

1,2,3,7,8,9-hexachlorinated dibenzo-p-dioxin

0.1

1,2,3,6,7,8-hexachlorinated dibenzo-p-dioxin

0.1

1,2,3,4,6,7,8-heptachlorinated dibenzo-p-dioxin

0.01

octachlorinated dibenzo-p-dioxin

0.0003

2,3,7,8-tetrachlorinated dibenzofuran

0.1

2,3,4,7,8-pentachlorinated dibenzofuran

0.3

1,2,3,7,8-pentachlorinated dibenzofuran

0.03

1,2,3,4,7,8-hexachlorinated dibenzofuran

0.1

1,2,3,6,7,8-hexachlorinated dibenzofuran

0.1

1,2,3,7,8,9-hexachlorinated dibenzofuran

0.1

2,3,4,6,7,8-hexachlorinated dibenzofuran

0.1

1,2,3,4,6,7,8-heptachlorinated dibenzofuran

0.01

1,2,3,4,7,8,9-heptachlorinated dibenzofuran

0.01

octachlorinated dibenzofuran

0.0003

Table 6 to Subpart LLL of Part 62 Table 6 to Subpart LLL of Part 62—Summary of Reporting Requirements for Existing Sewage Sludge Incineration Units 1

Report

Due date

Contents

Reference

Final control plan and final compliance report

No later than 10 business days after the compliance date

1. Final control plan including air pollution control device descriptions, process changes, type of waste to be burned, and the maximum design sewage sludge burning capacity

§ 62.16030(a).

2. Notification of any failure to submit the final control plan and achieve final compliance

3. Notification of any closure

Initial compliance report

No later than 60 days following the initial performance test

1. Company name and address 2.Statement by a responsible official, with that official's name, title, and signature, certifying the accuracy of the content of the report. 3. Date of report. 4. Complete test report for the initial performance test. 5. Results of CMS 2 performance evaluation.

§ 62.16030(b).

6. The values for the site-specific operating limits and the calculations and methods used to establish each operating limit

7. Documentation of installation of bag leak detection system for fabric filter

8. Results of initial air pollution control device inspection, including a description of repairs

9. The site-specific monitoring plan required under § 62.15995

10. The site-specific monitoring plan for your ash handling system required under § 62.15995

Annual compliance report

No later than 12 months following the submission of the initial compliance report; subsequent reports are to be submitted no more than 12 months following the previous report

1. Company name and address 2. Statement and signature by responsible official. 3. Date and beginning and ending dates of report. 4. If a performance test was conducted during the reporting period, the results of the test, including any new operating limits and associated calculations and the type of activated carbon used, if applicable.

§ 62.16030(c).

5. For each pollutant and operating parameter recorded using a CMS, the highest recorded 3-hour average and the lowest recorded 3-hour average, as applicable

6. If no deviations from emission limits, emission standards, or operating limits occurred, a statement that no deviations occurred

7. If a fabric filter is used, the date, time, and duration of alarms

8. If a performance evaluation of a CMS was conducted, the results, including any new operating limits and their associated calculations

9. If you met the requirements of § 62.16000(a)(3) and did not conduct a performance test, include the dates of the last three performance tests, a comparison to the 50 percent emission limit threshold of the emission level achieved in the last three performance tests, and a statement as to whether there have been any process changes

10. Documentation of periods when all qualified SSI unit operators were unavailable for more than 8 hours but less than 2 weeks

11. Results of annual pollutions control device inspections, including description of repairs

12. If there were no periods during which your CMSs had malfunctions, a statement that there were no periods during which your CMSs had malfunctions

13. If there were no periods during which your CMSs were out of control, a statement that there were no periods during which your CMSs were out of control

14. If there were no operator training deviations, a statement that there were no such deviations

15. Information on monitoring plan revisions, including a copy of any revised monitoring plan

Deviation report (deviations from emission limits, emission standards, or operating limits, as specified in § 62.16030(e)(1))

By August 1 of a calendar year for data collected during the first half of the calendar year; by February 1 of a calendar year for data collected during the second half of the calendar year

If using a CMS: 1. Company name and address. 2. Statement by a responsible official. 3. The calendar dates and times your unit deviated from the emission limits or operating limits. 4. The averaged and recorded data for those dates. 5. Duration and cause of each deviation. 6. Dates, times, and causes for monitor downtime incidents. 7. A copy of the operating parameter monitoring data during each deviation and any test report that documents the emission levels.

§ 62.16030(d).

8. For periods of CMS malfunction or when a CMS was out of control, you must include the information specified in § 62.16030(d)(3)(viii)

If not using a CMS:

1. Company name and address

2. Statement by a responsible official

3. The total operating time of each affected SSI unit

4. The calendar dates and times your unit deviated from the emission limits, emission standard, or operating limits

5. The averaged and recorded data for those dates

6. Duration and cause of each deviation

7. A copy of any performance test report that showed a deviation from the emission limits or standards

8. A brief description of any malfunction, a description of actions taken during the malfunction to minimize emissions, and corrective action taken

Notification of qualified operator deviation (if all qualified operators are not accessible for 2 weeks or more)

Within 10 days of deviation

1. Statement of cause of deviation 2. Description of actions taken to ensure that a qualified operator will be available 3. The date when a qualified operator will be accessible

§ 62.16030(e).

Notification of status of qualified operator deviation

Every 4 weeks following notification of deviation

1. Description of actions taken to ensure that a qualified operator is accessible 2. The date when you anticipate that a qualified operator will be accessible. 3. Request for approval to continue operation.

§ 62.16030(e).

Notification of resumed operation following shut down (due to qualified operator deviation and as specified in § 62.15945(b)(2)(i)

Within five days of obtaining a qualified operator and resuming operation

1. Notification that you have obtained a qualified operator and are resuming operation

§ 62.16030(e).

Notification of a force majeure

As soon as practicable following the date you first knew, or through due diligence should have known that the event may cause or caused a delay in conducting a performance test beyond the regulatory deadline; the notification must occur before the performance test deadline unless the initial force majeure or a subsequent force majeure event delays the notice, and in such cases, the notification must occur as soon as practicable

1. Description of the force majeure event 2. Rationale for attributing the delay in conducting the performance test beyond the regulatory deadline to the force majeure. 3. Description of the measures taken or to be taken to minimize the delay. 4. Identification of the date by which you propose to conduct the performance test.

§ 62.16030(f).

Notification of intent to start or stop use of a CMS

1 month before starting or stopping use of a CMS

1. Intent to start or stop use of a CMS

§ 62.16030(g)

Notification of intent to conduct a performance test

At least 30 days prior to the performance test

1. Intent to conduct a performance test to comply with this subpart

Notification of intent to conduct a rescheduled performance test

At least 7 days prior to the date of a rescheduled performance test

1. Intent to conduct a rescheduled performance test to comply with this subpart

1 This table is only a summary, see the referenced sections of the rule for the complete requirements.

2 CMS means continuous monitoring system.

§ 62.101 Identification of sources.

The plan applies to existing facilities at the following sulfuric acid plants:

(a) Acid plants operated by

(1) Reichhold Chemical Company in Tuscaloosa,

(2) Stauffer Chemical Company in Mobile, and

(3) Estech Chemical in Dothan.

(b) There are no oleum plants.

(c) There are not sulfur-burning plants.

(d) There are no bound sulfur feedstock plants.

§ 62.102 Identification of sources.

The plan currently does not identify any sources subject to its fluoride emission limits.

§ 62.103 Identification of sources.

The plan applies to existing municipal solid waste landfills for which construction, reconstruction, or modification was commenced before May 30, 1991, that accepted waste at any time since November 8, 1987, or that have additional capacity available for future waste deposition, as described in 40 CFR part 60, subpart Cc.

§ 62.104 Identification of sources.

The plan applies to existing facilities with a municipal waste combustor (MWC) unit capacity greater than 250 tons per day of municipal solid waste (MSW) at the following MWC sites:

(a) Solid Waste Disposal Authority of the City of Huntsville MWC, Huntsville, Alabama.

(b) [Reserved]

§ 62.105 Identification of sources.

The plan applies to existing hospital/medical/infectious waste incinerators for which construction, reconstruction, or modification was commenced before June 20, 1996, as described in 40 CFR part 60, subpart Ce.

§ 62.106 Identification of plan—negative declaration.

Letter from the Alabama Department of Environmental Management submitted January 11, 2001, certifying that there are no small municipal waste combustion units subject to 40 CFR part 60, subpart BBBB.

§ 62.107 Identification of sources.

(a) Approval of State Plan for Commercial and Industrial Solid Waste Incineration Units. Effective February 10, 2020, EPA approved Alabama's State Plan for Commercial and Solid Waste Incineration Units, which is codified at Alabama Rule 335-3-3-.05, amended December 8, 2017, and which is incorporated by reference. The plan applies to each existing commercial and industrial solid waste incineration unit and air curtain incineration unit in the State of Alabama that commenced construction on or before June 4, 2010, or commenced modification or construction after June 4, 2010, but no later than August 7, 2013, as such incineration units are defined in 40 CFR 60.2875 and 40 CFR part 60.

(b) Incorporation by reference. (1) The material incorporated by reference in this section was approved by the Director of the Federal Register Office in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies of the material may be inspected or obtained from the EPA Docket Center—Public Reading Room, EPA West Building, Room 3334, 1301 Constitution Avenue NW, Washington, DC 20004 or U.S. EPA, Region 4, Air Analysis and Support Branch, 61 Forsyth Street, Atlanta, GA 30303. The telephone number for the Public Reading Room is [phone]. Copies may be inspected at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email [email protected] or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

(2) State of Alabama, Alabama Department of Environmental Management. 1400 Coliseum Boulevard, Montgomery, AL 36110, 334-271-7700, adem.alabama.gov.

(i) Administrative Rule 335-3-3-3.05, Incineration of Commercial and Industrial Solid Waste (Administrative Code division 335-3, Air Division—Air Pollution Control Program), adopted October 20, 2017.

(ii) [Reserved]

§ 62.350 Identification of plan—negative declaration.

The Alaska Department of Environmental Conservation submitted on June 9, 1977, certification that there are no existing phosphate fertilizer plants in the State subject to part 60, subpart B of this chapter.

§ 62.351 Identification of plan—negative declaration.

The Alaska Department of Environmental Conservation submitted on June 9, 1977, certification that there are no existing sulfuric acid plants in the State subject to part 60, subpart B of this chapter.

§ 62.352 Identification of plan—negative declaration.

The Alaska Department of Environmental Conservation submitted on June 9, 1977, certification that there are no existing kraft pulp mills in the State subject to part 60, subpart B of this chapter.

§ 62.353 Identification of plan—negative declaration.

The Alaska Department of Environmental Conservation submitted on June 9, 1977, certification that there are no existing primary aluminum reduction plants in the State subject to part 60, subpart B of this chapter.

§ 62.354 Identification of plan—negative declaration.

Letter from the Department of Environmental Conservation submitted June 30, 1997 certifying that there are no existing municipal waste combustor units in the State of Alaska that are subject to part 60, subpart Cb, of this chapter.

§ 62.600 Identification of plan.

(a) The Arizona Department of Environmental Quality submitted on June 17, 1997, and June 29, 1999, the State of Arizona's Section 111(d) Plan for Existing Municipal Solid Waste Landfills.

(b) Control of landfill gas emissions from existing municipal solid waste landfills, submitted by the Arizona Department of Environmental Quality on July 24, 2018, to implement 40 CFR part 60, subpart Cf. The Plan includes the regulatory provisions cited in paragraph (d) of this section, which the EPA incorporates by reference.

(c) After August 27, 2020, the substantive requirements of the municipal solid waste landfills state plan are contained in paragraph (b) of this section and owners and operators of municipal solid waste landfills in Arizona must comply with the requirements in paragraph (b) of this section.

(d)(1) The material incorporated by reference in this section was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. You may obtain copies at the EPA Region 9 office, 75 Hawthorne Street, San Francisco, California 94105, 415-947-8000 or from the source listed in this paragraph (d). Copies may be inspected at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email [email protected] or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.

(2) State of Arizona, Arizona Secretary of State, 1700 W Washington St Floor 7, Phoenix, AZ 85007.

(i) Title 18 Arizona Administrative Code, Title 2. Department of Environmental Quality—Air Pollution Control:

(A) Article 7. Existing Stationary Source Performance Standards R18-2-731 Standards of Performance for Existing Municipal Solid Waste Landfills, effective August 10, 2018.

(B) Article 9. New Source Performance Standards R18-2-901 Standards of Performance for New Stationary Sources, paragraph (80), effective August 10, 2018.

(ii) [Reserved]

§ 62.601 Identification of sources.

(a) The plan applies to all existing municipal solid waste landfills for which construction, reconstruction, or modification was commenced before May 30, 1991, as described in 40 CFR part 60, subpart Cc.

(b) The plan in § 62.600(b) applies to all existing municipal solid waste landfills under the jurisdiction of the Arizona Department of Environmental Quality for which construction, reconstruction, or modification was commenced on or before July 17, 2014.